Solo contaminado com cádmio: extratibilidade do metal e cinética química de degradação da matéria orgânica de torta de filtro

The chemical kinetics of sugarcane filter cake (FC) organic matter degradation at rates (0, 40, 80, and 120 t ha-1) in non-contaminated and different degrees of cadmium-contaminated Oxisol (0.19, 28, 56, 112 and 200 mg Cd kg-1) and DTPA-extractable Cd was studied. FC degradation was determined by quantifying CO2 emitted from soil samples during 72 days of incubation. DTPA-extractable Cd was performed after the incubation period. FC degradation was described by a two-stage equation of chemical kinetics. FC degradation rates were between 15 and 33%. Total CO2 emitted from FC declined with increasing degree in Cd-contamination and the DTPA-extractable Cd declined with FC rates.

Bionanocompósitos preparados por incorporação de nanocristais de celulose em polímeros biodegradáveis por meio de evaporação de solvente, automontagem ou eletrofiação

This review reports the preparation and characterization of bionanocomposites based on biodegradable polymers reinforced with cellulose nanocrystals (CNC) described in the literature. The outstanding potential of cellulose nanocrystals as reinforcement fillers of biodegradable polymers is presented with an emphasis on the solution casting process, which is an appropriate method to investigate the physico-chemical effects of the incorporation of CNC into the polymeric matrices. Besides solution casting, other small scale methods such as electrospinning and layer-by-layer are also covered.

DETERMINAÇÃO DE Cd E Pb EM AMOSTRAS DE GOMA XANTANA POR GF AAS

This paper describes the evaluation of a method for determination of Cd and Pb in xanthan gum samples by Graphite Furnace Atomic Absorption Spectrometry (GF AAS) using NH4H2PO4 as the chemical modifier. The sample preparation was performed using a reflux system adapted in the digestion tubes. With this system it was possible to increase the temperature of the digester block above the boiling point of the reaction medium, preventing loss of analyte and excessive evaporation of acids during heating. Samples were digested with HNO3 for 3 h in a digester block at 220 ºC. The limits of detection for Cd and Pb were 2.2 and 33.8 ng g-1, respectively. The RSDs for both analytes were, on average, lower than 5.0% and accuracy was verified by recovery tests, yielding values in the 83-100% range.

NANOCRISTAIS DE CELULOSE A PARTIR DE CELULOSE BACTERIANA

Bacterial cellulose produced from Gluconacetobacter xilinus was used to produce cellulose nanocrystals by sulfuric acid hydrolysis. Hydrolysis was performed with 64% sulfuric acid at 50 ºC with the hydrolysis time ranging between 5 and 90 min. The production of nanocrystals was observed to have size distributions that were dependent on hydrolysis times up to 10 min, after which time the suspensions showed distributions closer in size. Results from thermal analysis and X-ray diffraction showed that the amorphous cellulose was removed, leaving only the crystalline portion. Self-supported films were formed from the suspension of nanocrystals and had iridescence characteristics. The films were characterized by microscopy measures and specular reflectance.

Simultaneous determination of Cd and Pb in antibiotics used in sugar-cane fermentation process by GFAAS

A method has been developed for the simultaneous determination of Cd and Pb in antibiotics used in sugar-cane fermentation by GFAAS. The integrated platform of transversely heated graphite atomizer was treated with tungsten to form a coating of tungsten carbide. Six samples of commercial solid antibiotics were analyzed by injecting 20 µL of digested samples into the pretreated graphite platform with co-injection of 5 µL of 1000 mg L-1 Pd as chemical modifier. Samples were mineralized in a closed-vessel microwave-assisted acid-digestion system using nitric acid plus hydrogen peroxide. The pyrolysis and atomization temperatures of the heating program of the atomizer were selected as 600°C and 2200°C, respectively. The calculated characteristic mass for Cd and Pb was 1.6 pg and 42 pg, respectively. Limits of detection (LOD) based on integrated absorbance were 0.02 µg L-1 Cd and 0.7 µg L-1 Pb and the relative standard deviations (n = 10) for Cd and Pb were 5.7% and 8.0%, respectively. The recoveries of Cd and Pb added to the digested samples varied from 91% to 125% (Cd) and 80% to 112% (Pb).

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Kokemäenjoen suiston kehitys, maaperämuodostumat ja niiden kemialliset piirteet

Suurelta osin Natura-alueeseen kuuluvan Kokemäenjoen suistoalueen kuivan maan ja suiston edustan vesialueen erityyppisten maaperäkerrostumien kerrosjärjestys ja alueellinen jakautuminen selvitettiin pintamaaperän kartoituksella, tutkimuskaivannoilla ja kairauksella. Suiston kerrostumat luokiteltiin viiteen maaperämuodostumaan. Vanhimmasta nuorimpaan, Toukari, Vainio-Mattila, Hevosluoto, Lanajuopa ja Säikkä muodostumaan. Nämä edustavat vanhoja Itämeren altaan ja nuorempia merelle päin etenevän suiston eri osien kerrostumisympäristöjä. Eri muodostumien fysikaaliset ja kemialliset ominaisuudet kuvattiin ja ne eroavat luonteeltaan ratkaisevasti toisistaan. Suiston etenemistä edustavat Hevosluoto- ja Säikkä-muodostumat ovat kontaminoituneet 1900-luvun alkupuolelta lähtien yhä voimakkaammin ihmistoiminnasta kertyvistä raskasmetallipitoisuuksista ja orgaanisista haitta-aineista. Tämä näkyy erityisesti elohopean, kadmiumin, arseenin, lyijyn, sinkin, nikkelin, dioksiinien ja furaanien kokonaispitoisuuksien kasvuna näissä muodostumissa. Pitoisuudet ovat suurimpia muodostumien nuorimmissa osissa. Kuivalla maalla raskasmetallipitoisuudet ylittävät paikoin valtioneuvoston pilaantuneelle maaperälle asettamat kynnysarvot, jolloin säädökset on huomioitava suiston maaperää muokattaessa. Vesialueella nämä kynnysarvot ylittyvät myös orgaanisten haitta-aineiden osalta. Tietyin osin ovat esimerkiksi arseenin ja nikkelin osalta taustapitoisuudet suistoalueen vanhimmassa Toukari muodostumassa jo luontaisesti kynnysarvoja suuremmat. Tämä pitää osata ottaa huomioon maansiirtotoimenpiteitä suunniteltaessa. Suistoon kerrostuvan maa-aineksen ja nopean maankohoamisen vuoksi suisto etenee nykyisin 30-40 m vuodessa merialueelle päin. Tämä mataloittaa vääjäämättömästi suiston edustan vesialueita kerrostumisen siirtyessä merelle päin. Näin myös Natura-alueen ainutlaatuiset biotoopit vähitellen siirtyvät merelle päin.

Adsorption of hydrogen sulfide by modified cellulose nano/microcrystals

Hydrogen sulfide is toxic and hazardous pollutant. It has been under great interest for past few years because of all the time tighten environmental regulations and increased interest of mining. Hydrogen sulfide gas originates from mining and wastewater treatment systems have caused death in two cases. It also causes acid rains and corrosion for wastewater pipelines. The aim of this master thesis was to study if chemically modified cellulose nanocrystals could be used as adsorbents to purify hydrogen sulfide out from water and what are the adsorption capacities of these adsorbents. The effects of pH and backgrounds on adsorption capacities of different adsorbents are tested. In theoretical section hydrogen sulfide, its properties and different purification methods are presented. Also analytical detection methods for hydrogen sulfide are presented. Cellulose nano/microcrystals, properties, application and different modification methods are discussed and finally theory of adsorption and modeling of adsorption is shortly discussed. In experimental section different cellulose nanocrystals based adsorbents are prepared and tested at different hydrogen sulfide concentrations and in different conditions. Result of experimental section was that the highest adsorption capacity at one component adsorption had wet MFC/CaCO3. At different pH the adsorption capacities of adsorbents changed quite dramatically. Also change of hydrogen sulfide solution background did have effect on adsorption capacities. Although, when tested adsorbents’ adsorption capacities are compared to those find in literatures, it seems that more development of MFC based adsorbents is needed.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Optical spectroscopy of organic material based on C60

The structure and optical properties of thin films based on C60 materials are studied. Reproducible vacuum method of thin fullerene films production with Cd impurity on Si, glass and mica surfaces is developed. Surface morphology of the films are investigated by AFM and SEM methods. The ab initio quantum - chemical calculations of the geometry, total energy and excited energy states of complex fullerene- cadmium telluride supramolecules are performed. Photoluminescence spectra of composite thin films based on C60 before and after X-ray irradiation were measured. The intensity of additional peaks is defined as the charge composition due to the type of substrate. These results are interpreted as an appearance of the dipole-allowed transitions in the fullerene excited singlet states spectrum cause of an interference with cadmium telluride. X-ray irradiated films were investigated, and additional peaks in photoluminescence spectra were detected. These peaks appear as a result of molecular complexes formation from C60CdTe mixture and dimerization of the films. Density functional B3LYP quantum-chemical calculations for C60CdTe, molecular complexes, (C60)2 and C120O dimers were performed to elucidate some experimental results.

Pharmacology and toxicology of diphenyl diselenide in several biological models

The pharmacology of synthetic organoselenium compounds indicates that they can be used as antioxidants, enzyme inhibitors, neuroprotectors, anti-tumor and anti-infectious agents, and immunomodulators. In this review, we focus on the effects of diphenyl diselenide (DPDS) in various biological model organisms. DPDS possesses antioxidant activity, confirmed in several in vitro and in vivo systems, and thus has a protective effect against hepatic, renal and gastric injuries, in addition to its neuroprotective activity. The activity of the compound on the central nervous system has been studied since DPDS has lipophilic characteristics, increasing adenylyl cyclase activity and inhibiting glutamate and MK-801 binding to rat synaptic membranes. Systemic administration facilitates the formation of long-term object recognition memory in mice and has a protective effect against brain ischemia and on reserpine-induced orofacial dyskinesia in rats. On the other hand, DPDS may be toxic, mainly because of its interaction with thiol groups. In the yeast Saccharomyces cerevisiae, the molecule acts as a pro-oxidant by depleting free glutathione. Administration to mice during cadmium intoxication has the opposite effect, reducing oxidative stress in various tissues. DPDS is a potent inhibitor of d-aminolevulinate dehydratase and chronic exposure to high doses of this compound has central effects on mouse brain, as well as liver and renal toxicity. Genotoxicity of this compound has been assessed in bacteria, haploid and diploid yeast and in a tumor cell line.

Heavy metals investigation in bovine tissues in Brazil

The aim of this study was to investigate the presence of arsenic, lead, and cadmium residues in samples of liver, kidney, and muscle of cattle during the years of 2002 to 2008. A total of 1017 samples from 20 Brazilian States were used. The samples were analyzed at the National Agricultural Laboratory using the atomic absorption spectrometry technique. Arsenic residues were detected in 15.7% of liver samples and 28.7% of kidney samples although no results have exceeded the MRL. With regard to lead, 16 samples of liver and 74 samples of kidney were contaminated (5.2 and 10.9%, respectively). Among these samples, only one liver and two of kidney samples had lead levels above the MRL. Cadmium was found with levels below the MRL in 12.5% of the liver samples, and only 3 samples (1%) were quantified above the MRL. Among the kidney samples, 420 (60.8% of the total tested) had cadmium residues, and five of them exceeded the limits established by legislation. It is concluded that the Brazilian meat meets the legislation requirements without putting consumer's healthy at risk since as it satisfies the national and international food-safety conditions.

Jätteiden kemiallisten ominaisuuksien spektrometriset online-mittausmenetelmät

Tässä diplomityössä käsiteltiin spektrometrisia online-mittausmenetelmiä jätteiden kemiallisten ja fysikaalisten ominaisuuksien määrittämiseksi. Tavoitteena oli selvittää, mitä ominaisuuksia menetelmillä voidaan mitata ja kuinka luotettavia tuloksia mittauksilla saadaan. Diplomityössä suoritettiin kirjallisuuskatsaus, jossa käsiteltiin kolmen spektrometrisen menetelmän soveltuvuutta reaaliaikaisiin jätemittauksiin. Työn empiirisessä osassa FPXRFanalysaattorilla mitattiin neljän eri jätenäytteen alkuainepitoisuuksia. Mittauksen tarkoituksena oli selvittää, mitä alkuaineita menetelmällä voidaan mitata. FPXRF-analysaattorilla saatuja tuloksia verrattiin ICP-MS-menetelmällä saatuihin tuloksiin regressioanalyysin avulla. Työssä todettiin, että FPXRF-analysaattori sopii parhaiten kaliumin, kalsiumin, ja raudan pitoisuuksien määrittämiseen. Lisäksi lyijyn, sinkin, kromin, kloorin, kuparin, kadmiumin, arseenin, fosforin, molybdeenin ja vanadiinin määrittäminen on mahdollista, mutta tarkan pitoisuuden saamiseksi laboratoriomenetelmien käyttö voi olla tarpeen. Tutkituista jätenäytteistä menetelmä soveltui parhaiten tuhkalle ja kompostille niiden fyysisten ominaisuuksien, kuten homogeenisuuden ja kosteuspitoisuuden takia. Biojätteelle menetelmä soveltui huonosti. FPXRF-analysaattorin luotettavuuteen vaikuttaa näytteen kosteuspitoisuus, homogeenisuus, partikkelikoko, mittaustapa ja laitteen kalibrointi. Työssä tarkastelluilla menetelmillä ei voida tällä hetkellä täysin korvata laboratorioanalyyseja. FPXRF-analysaattoria voidaan kuitenkin käyttää kvalitatiiviseen tai semikvantitatiiviseen haitta-aineiden analysointiin, millä voidaan vähentää kalliiden laboratorioanalyysien tarvetta.

Far infrared optical properties of V and Cr doped Sb2Te3 /

The far infrared reflectance of Sb2Te3 , Sbi.97Vo.o3Te3 and Sbi.94Cr .o6Te3 was measured near normal incidence at different temperatures (between 45K and 300K). The direct current resistivities of the above samples were also measured between the temperatures of 4K and 300K. Also Kramers Kronig (KK) analyses were performed on the reflectance spectra to obtain the optical conductivities. In the doped samples, it was observed that a phonon at 62cm-1 softens to about 55cm-1 on decreasing the temperature from 295K to 45K. Also, it was observed that the plasma frequency of the doped samples is independent of doping. The scattering rate for the vanadium doped sample was seen to be greater than that for the chromium doped sample despite the fact that vanadium impurity density is less than that of chromium. The Drude-Lorentz model fits to the KK optical conductivity show that the samples used in this work are conventional metals. Definitive measurements of the temperature dependence of the scattering rate across the ferromagnetic transition await equipment changes allowing measurements at low temperature using the mercury cadmium telluride (MCT) detector.

Sample preparation and heavy metal determination by atomic spectrometry /

Microwave digestions of mercury in Standards Reference Material (SRM) coal samples with nitric acid and hydrogen peroxide in quartz vessels were compared with Teflon® vessel digestion by using flow injection cold vapor atomic absorption spectrometry. Teflon® vessels gave poor reproducibiUty and tended to deliver high values, while the digestion results from quartz vessel show good agreement with certificate values and better standard deviations. Trace level elements (Ag, Ba, Cd, Cr, Co, Cu, Fe, Mg, Mn, Mo, Pb, Sn, Ti, V and Zn) in used oil and residual oil samples were determined by inductively coupled plasma-optical emission spectrometry. Different microwave digestion programs were developed for each sample and most of the results are in good agreement with certified values. The disagreement with values for Ag was due to the precipitation of Ag in sample; while Sn, V and Zn values had good recoveries from the spike test, which suggests that these certified values might need to be reconsidered. Gold, silver, copper, cadmium, cobalt, nickel and zinc were determined by continuous hydride generation inductively coupled plasma-optical emission spectrometry. The performance of two sample introduction systems: MSIS™ and gas-liquid separator were compared. Under the respective optimum conditions, MSIS^"^ showed better sensitivity and lower detection limits for Ag, Cd, Cu, Co and similar values for Au, Ni and Zn to those for the gas-liquid separator.