Critical current degradation of Bi-2223 composite tapes induced by cyclic deformation and fatigue-related effects

Application of high temperature superconductor Bi2Sr2Ca2Cu3Ox. (Bi-2223) compound embedded in an Ag matrix requires the knowledge of critical current as a function of mechanical properties. Commercial tapes available in different types have been developed in industrial production scale in which a combination of small diameter filaments, long tape lengths and a ductile matrix results in a conductor with low crack formation and good tolerance against strain. The measurement of critical current and the evaluation of n-index from V-I characteristic curves of Bi-2223/Ag composite tapes subjected to an initial bending strain as a function of number of thermal cycles were done for two types of Bi-2223/Ag composite tapes: with and without steel tape reinforcement. The results showed that tapes with reinforcement presented small critical current degradation as a function of the number of thermal cycles whereas tapes without reinforcement exhibited steadily critical current degradation caused by the propagation of cracks. The n-index followed the same critical current behavior.

Fault current test of a bifilar Bi-2212 bulk coil

A bifilar Bi-2212 bulk coil with parallel shunt resistor was tested under fault current condition using a 3 MVA single-phase transformer in a 220 V-60 Hz line achieving fault current peak of 8 kA. The fault current tests are performed from steady state peak current of 200 A by applying controlled short circuits up to 8 kA varying the time period from one to six cycles. The test results show the function of the shunt resistor providing homogeneous quench behavior of the HTS coil besides its intrinsic stabilizing role. The limiting current ratio achieves a factor 4.2 during 5 cycles without any degradation.

Evaluation of different rhodium modifiers and coatings on the simultaneous determination of As, Bi, Pb, Sb, Se and of Co, Cr, Cu, Fe, Mn in milk by electrothermal atomic absorption spectrometry

Different kinds of modifiers and coatings on the integrated platform of transversely heated graphite atomizer (THGA) have been tested for the simultaneous determination of two group of elements: the first, the more volatile, formed by arsenic, bismuth, lead, antimony and selenium; the second, the less volatile, formed by cobalt, chromium, cupper, iron and manganese in milk by electrothermal atomic absorption spectrometry. Different Rh-modifiers were studied, such as Rh-coated platforms (Rh), carbide plus rhodium coated platforms (W-Rh, Zr-Rh), carbide-coated platforms (W and Zr) with co-injection of RhCl3, solutions and uncoated platforms with injection of solutions of Pd(NO3)(2), Mg(NO3)(2), and RhCl3. Milk samples were diluted 1:10 in 1.0% HNO3 and injected into the tube. The mass of modifier deposited and co-injected in the tube and the use of end capped tubes were also evaluated in order to improve the electrothermal behavior of analytes. Integrated platform pretreated with W plus co-injection RhCl3 for first group and pretreated with W-Rh for second group were elected. For 20 mu L injected samples the analytical curves in the 5.0-20.0 mu g L-1 concentration range have good linear correlation coefficients (r > 0.998). Relative standard deviations (n = 12) are < 6% and the calculated characteristic masses are between 5 pg and 62 pg.

Some comments on the bi(tri)-Hamiltonian structure of generalized AKNS and DNLS hierarchies

We give the correct prescriptions for the terms involving ∂ -1 xδ(x - y), in the Hamiltonian structures of the AKNS and DNLS systems, necessary for the Jacobi identities to hold. We establish that the sl(2) and sl(3) AKNS systems are tri-Hamiltonians and construct two compatible Hamiltonian structures for the sl(n) AKNS system. We give a method for the derivation of the recursion operator for the sl(n + 1) DNLS system, and apply it explicitly to the sl(2) case, showing that such a system is tri-Hamiltonian. © 1998 Elsevier Science B.V.

Evaluation of Ir-based modifiers in the simultaneous determination of As, Bi, Pb, Sb, and Se in milk by graphite furnace atomic absorption spectrometry

Different modifiers (IrCl3, W+IrCl3, Zr+IrCl 3) and coatings (Ir, W-Ir, Zr-Ir) were evaluated for the simultaneous determination of arsenic, bismuth, lead, antimony, and selenium in milk by graphite furnace atomic absorption spectrometry using the 'end-capped' transversely heated graphite atomizer (THGA). Integrated platform, pretreated with Zr-Ir as permanent modifier, was elected as the optimum surface modification resulting in up to 250 firings. Two additional recoatings were possible without significant changes in the analytical performance (750 firings). For 20 μL of matrix-matched standard solutions using diluted (1:10) milk samples, typical correlation coefficients between integrated absorbance and analyte concentration (5.00-20.0 μg/L) was always better than 0.999. The levels of the analytes found in commercial milk samples were lower than the limit of detection: 2.9 μg/L As, 2.9 μg/L Bi, 1.8 μg/L Pb, 1.9 μg/L Sb, and 2.5 μg/L Se. Recoveries were found within the following intervals: 88-114% for As, 89-118% for Bi, 89-113% for Pb, 91-115% for Sb, and 92-115% for Se. The relative standard deviations (n = 12) were ≤2% (As), ≤ 5% (Bi), ≤ 1.4% (Pb), ≤ 3% (Sb), and 5% (Se), and the respective calculated characteristic masses were 54 pg As, 55 pg Bi, 40 pg Pb, 56 pg Sb, and 51 pg Se.

Influence of microwave energy on structural and piezoelectric response of Bi 4Ti 3O 12 ceramics

Bismuth titanate ceramics (Bi 4Ti 3O 12) with 10 wt% in excess of bismuth (BIT10) were prepared by the polymeric precursor method and sinterized in microwave (MW) and conventional furnaces (CF). The effect of microwave energy on structural and electrical behavior of BIT10 ceramics was investigated by means of X-ray diffraction (XRD), Scanning electron microscopy (SEM) and electrical measurements. The results of the BIT10 ceramics processed in the microwave furnace (MW) showed a high structural organization compared to conventional treatment (CF). Size of grains and dieletrical properties are influenced by annealing conditions while coercitive field is not dependent on it. The maximum dielectric permittivity (12000) was obtained for the sample sintered in the microwave furnace. Piezoelectric force microscopy images reveals that in-plane response may not change its sign upon polarization switching, while the out-of-plane response does with the influence of microwave energy. Copyright © 2010 American Scientific Publishers All rights reserved.

Morphotropic phase boundary and electrical properties of 1-x[Bi 0.5Na0.5]TiO3 -xBa[Zr0.25Ti 0.75]O3 lead-free piezoelectric ceramics

Lead-free solid solutions (1-x)Bi0.5Na0.5TiO 3 (BNT)-xBaZr0.25Ti0.75O3 (BZT) (x=0, 0.01, 0.03, 0.05, and 0.07) were prepared by the solid state reaction method. X-ray diffraction (XRD) and Rietveld refinement analyses of 1-x(BNT)-x(BZT) solid solution ceramic were employed to study the structure of these systems. A morphotropic phase boundary (MPB) between rhombohedral and cubic structures occured at the composition x=0.05. Raman spectroscopy exhibited a splitting of the (TO3) mode at x=0.05 and confirmed the presence of MPB region. Scanning electron microcopy (SEM) images showed a change in the grain shape with the increase of BZT into the BNT matrix lattice. The temperature dependent dielectric study showed a gradual increase in dielectric constant up to x=0.05 and then decrease with further increase in BZT content. Maximum coercive field, remanent polarization and high piezoelectric constant were observed at x=0.05. Both the structural and electrical properties show that the solid solution has an MPB around x=0.05. © 2012 Elsevier Ltd and Techna Group S.r.l.

Síntese e caracterização de nanoestruturas e filmes finos de 'BI' 'FE' 'OIND.3' modificado com samário visando aplicação em memórias de múltiplos estados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo descritivo das mamografias categorias IV e V da classificação BI-RADS

Pós-graduação em Ginecologia, Obstetrícia e Mastologia - FMB

Contribuição dos exames ultrassonográficos convencional, Doppler e classificação Bi-Radis® na avaliação dos tumores mamários em cadelas

Pós-graduação em Medicina Veterinária - FMVZ

Modelagem 2,5D dos campos usados no Método Eletromagnético a Multi-Frequência - EMMF

Esta tese mostra a modelagem 2,5D de dados sintéticos do Método Eletromagnético a Multi-frequência (EMMF). O trabalho é apresentado em duas partes: a primeira apresenta os detalhes dos métodos usados nos cálculos dos campos gerados por uma bobina horizontal de corrente colocada sobre a superfície de modelos bidimensionais; e a segunda, usa os resultados obtidos para simular os dados medidos no método EMMF, que são as partes real e imaginária da componente radial do campo magnético gerado pela bobina. Nesta segunda parte, observamos o comportamento do campo calculado em diversos modelos, incluindo variações nas propriedades físicas e na geometria dos mesmos, com o intuito de verificar a sensibilidade do campo observado com relação às estruturas presentes em uma bacia sedimentar. Com esta modelagem, podemos observar as características dos dados e como as duas partes, real e imaginária, contribuem com informações distintas e complementares. Os resultados mostram que os dados da componente radial do campo magnético apresentam muito boa resolução lateral, mesmo estando a fonte fixa em uma única posição. A capacidade desses dados em distinguir e resolver estruturas alvo será fundamental para o trabalho futuro de inversão, bem como para a construção de seções de resistividade aparente.

Comparação dos efeitos do eletrojato equatorial nos dados magnetotelúricos bi e tridimensionais

Este trabalho trata da comparação dos efeitos do eletrojato equatorial nos dados magnetotelúricos bi e tridimensionais. Ele compõe-se fundamentalmente de duas partes: Na primeira, que consiste na comparação dos efeitos dos modelos bi e tridimensionais (linha de corrente e eletrojato gaussiano), determinamos as dimensões que deve apresentar uma estrutura tridimensional para que a resposta magnetotelúrica proveniente dessa estrutura, nas polarizações YX e XY, possa ser substituída pela resposta magnetotelúrica proveniente de uma estrutura bidimensional nos modos TE e TM respectivamente, para a resistividade aparente e fase. Os resultados mostram, para um embasamento condutivo ou resistivo, que é necessário aumentar a dimensão da estrutura tridimensional na direção principal acima de dezesseis vezes, em relação à dimensão inicial, para que a resposta magnetotelúrica proveniente dessa estrutura na polarização YX, possa ser substituída pela resposta magnetotelúrica proveniente de uma estrutura bidimensional no modo TE; no caso da polarização ser XY, essa substituição ocorrerá, no modo TM bidimensional, se aumentarmos a dimensão da estrutura tridimensional na direção principal acima de vinte e seis vezes em relação à dimensão inicial. Na segunda parte, que consiste na determinação dos efeitos do eletrojato equatorial Onwumechilliano, posicionamos a estrutura tridimensional a 10 km, 100 km, 300 km, 500 km, 1000 km e 1500 km, respectivamente, de distância do eletrojato. Dessa forma, determinamos a distância na qual os efeitos do eletrojato equatorial Onwumechilliano sobre as sondagens magnetotelúricas são praticamente desprezíveis. Verificamos que, posicionando a estrutura tridimensional a 1500 km de distância da fonte, para embasamento condutivo, o eletrojato não afeta as sondagens magnetotelúricas. Quando o embasamento é resistivo, o eletrojato afeta as sondagens magnetotelúricas, mesmo posicionando-se a estrutura tridimensional a 1500 km de distância da fonte. De um modo geral, constatamos que o eletrojato equatorial afeta as sondagens magnetotelúricas para freqüências inferiores a 10^-2 Hz, tanto na resistividade aparente quanto na fase e em ambas as polarizações, principalmente, quando o embasamento é resistivo. Observamos também que o efeito galvânico é mais pronunciado na polarização YX que na XY.

Espécies moleculares e supramoleculares de 'PD'(II)' com ligantes mono, bi e polidentados : caracterização estrutural e atividades biológicas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aplicação do '[RuCl IND. 3(DPPB)H IND.2 O] na obtenção do complexos mono e binucleares

Pós-graduação em Química - IQ

Elevated micronucleus frequency in patients with type 2 diabetes, dyslipidemia and periodontitis

The over-production of reactive oxygen species (ROS) can cause oxidative damage to a large number of molecules, including DNA, and has been associated with the pathogenesis of several disorders, such as diabetes mellitus (DM), dyslipidemia and periodontitis (PD). We hypothesise that the presence of these diseases could proportionally increase the DNA damage. The aim of this study was to assess the micronucleus frequency (MNF), as a biomarker for DNA damage, in individuals with type 2 DM, dyslipidemia and PD. One hundred and fifty patients were divided into five groups based upon diabetic, dyslipidemic and periodontal status (Group 1 - poor controlled DM with dyslipidemia and PD; Group 2 - well-controlled DM with dyslipidemia and PD; Group 3 - without DM with dyslipidemia and PD; Group 4 - without DM, without dyslipidemia and with PD; and Group 5 - without DM, dyslipidemia and PD). Blood analyses were carried out for fasting plasma glucose, HbA1c and lipid profile. Periodontal examinations were performed, and venous blood was collected and processed for micronucleus (MN) assay. The frequency of micronuclei was evaluated by cell culture cytokinesis-block MN assay. The general characteristics of each group were described by the mean and standard deviation and the data were submitted to the Mann-Whitney, Kruskal-Wallis, Multiple Logistic Regression and Spearman tests. The Groups 1, 2 and 3 were similarly dyslipidemic presenting increased levels of total cholesterol, low density lipoprotein cholesterol and triglycerides. Periodontal tissue destruction and local inflammation were significantly more severe in diabetics, particularly in Group 1. Frequency of bi-nucleated cells with MN and MNF, as well as nucleoplasmic bridges, were significantly higher for poor controlled diabetics with dyslipidemia and PD in comparison with those systemically healthy, even after adjusting for age, and considering Bonferroni's correction. Elevated frequency of micronuclei was found in patients affected by type 2 diabetes, dyslipidemia and PD. This result suggests that these three pathologies occurring simultaneously promote an additional role to produce DNA impairment. In addition, the micronuclei assay was useful as a biomarker for DNA damage in individuals with chronic degenerative diseases.