Development of capacitive sensor for measuring soil water content

The irrigation management based on the monitoring of the soil water content allows for the minimization of the amount of water applied, making its use more efficient. Taking into account these aspects, in this work, a sensor for measuring the soil water content was developed to allow real time automation of irrigation systems. This way, problems affecting crop yielding such as irregularities in the time to turn on or turn off the pump, and excess or deficit of water can be solved. To develop the sensors were used stainless steel rods, resin, and insulating varnish. The sensors measuring circuit was based on a microcontroller, which gives its output signal in the digital format. The sensors were calibrated using soil of the type “Quartzarenic Neosoil”. A third order polynomial model was fitted to the experimental data between the values of water content corresponding to the field capacity and the wilting point to correlate the soil water content obtained by the oven standard method with those measured by the electronic circuit, with a coefficient of determination of 93.17%, and an accuracy in the measures of ±0.010 kg kg-1. Based on the results, it was concluded that the sensor and its implemented measuring circuit can be used in the automation process of irrigation systems.

Experimental evaluation of the performance of a wireless sensor network in agricultural environments

The aim of this study was to perform an experimental study to evaluate the proper operation distance between the nodes of a wireless sensor network available on the market for different agricultural crops (maize, physic nut, eucalyptus). The experimental data of the network performance offers to farmers and researchers information that might be useful to the sizing and project of the wireless sensor networks in similar situations to those studied. The evaluation showed that the separation of the nodes depends on the type of culture and it is a critical factor to ensure the feasibility of using WSN. In the configuration used, sending packets every 2 seconds, the battery life was about four days. Therefore, the autonomy may be increased with a longer interval of time between sending packets.

Seasonality of net radiation in two sub-basins of Paracatu by the use of modis sensor products

The net radiation (Rn) represents the main source of energy for physical and chemical processes that occur in the surface-atmosphere interface, and it is used for air and soil heating, water transfer, in the form of vapor from the surface to the atmosphere, and for the metabolism of plants, especially photosynthesis. If there is no record of net radiation in certain areas, the use of information is important to help determine it. Among them we can highlight those provided by remote sensing. In this context, this work aims to estimate the net radiation, with the use of products of MODIS sensor, in the sub-basins of Entre Ribeiros creek and Preto River, located between the Brazilian states of Goiás and Minas Gerais. The SEBAL (Surface Energy Balance Algorithm for Land) was used to obtain the Rn in four different days in the period of July to October, 2007. The Rn results obtained were consistent with others cited in the literature and are important because the orbital information can help determine the Rn in areas where there are not automatic weather stations to record the net radiation.

Uso de imagens do sensor orbital modis na estimação de datas do ciclo de desenvolvimento da cultura da soja para o estado do Paraná – Brasil

RESUMO O Estado do Paraná caracteriza-se por uma grande variabilidade de épocas de semeadura (DS) e, consequentemente, pelo desenvolvimento máximo vegetativo (DMDV), colheita (DC) e ciclo (CI) para a cultura da soja. O objetivo deste trabalho foi estimar essas datas para o período de primavera-verão do ano-safra de 2011/2012, por meio de séries temporais de imagens do Índice de Vegetação Realçado (do inglês Enhanced Vegetation Index - EVI) do sensor Modis (Moderate Resolution Imaging Spectroradiometer). Gerou-se um perfil espectrotemporal médio de EVI, considerando todos os pixels mapeados como soja dentro de cada município. Estes dados serviram de entrada no software Timesat para estimar os decêndios do ciclo da cultura (DS, DMDV, DC e CI) por municípios. Os resultados mostraram que existe grande variabilidade de datas de plantio em diferentes mesorregiões do Estado. Verificaram-se também divergências entre os resultados encontrados e os dados oficiais de DS e DC. A maior parte da semeadura (65,16%) esteve entre o terceiro decêndio de outubro e o primeiro decêndio de novembro. A maior parte da área de soja do Estado do Paraná (65,46%) teve seu DMDV em janeiro e colheita em março (53,92%).

Streamlining Launch Support Operations in a Product Platform

The new product development process is a massive investment to a company that aims to reduce their products’ time-to-market. Capability to shorter time-to market allows longer life-cycle to products which are introduced to market earlier but also give advantage to start product launch later while simultaneously learning from customer behavior and competitors. The product launch support operations are the last ramp-up activities before the product launching. This study defines what these operations mean in a product platform and how they can be streamlined to be more efficient. The methodology includes interviews, innovative group brainstorming and regular working group meetings. The challenges concerning the current situation of product launch support operations are allocated into four categories: General, Process, Project Resources and Project Management including altogether ten sub challenges. The challenges include issues related to technology and marketing management, branding strategy, organizing the global platform structure, harmonizing processes and clarifying handovers between shareholders in the process. The study makes a suggestion of a new Product Launch Support organization and clarification of its roles, responsibilities and tasks. In addition a new project management tool and Lessons Learned are suggested to improve the project management. The study can be seen as a pre-study when having an aim at combining technological and marketing know-how in the product ramp-up process before actual production. The future proceedings are suggested to include more detailed specifications and implementation in order to reach the long range target, reduced the time-to-market.

A platform for anti-biofilm assays combining viability, biomass and matrix quantifications in susceptibility assessments of antimicrobials against Staphylococcus aureus biofilms

Bacteria can exist as planktonic, the lifestyle in which single cells exist in suspension, and as biofilms, which are surface-attached bacterial communities embedded in a selfproduced matrix. Most of the antibiotics and the methods for antimicrobial work have been developed for planktonic bacteria. However, the majority of the bacteria in natural habitats live as biofilms. Biofilms develop dauntingly fast high resistance towards conventional antibacterial treatments and thus, there is a great need to meet the demands of effective anti-biofilm therapy. In this thesis project it was attempted to fill the void of anti-biofilm screening methods by developing a platform of assays that evaluate the effect that screened compounds have on the total biomass, viability and the extracellular polysaccharide (EPS) layer of the biofilms. Additionally, a new method for studying biofilms and their interactions with compounds in a continuous flow system was developed using capillary electrochromatography (CEC). The screening platform was utilized with a screening campaign using a small library of cinchona alkaloids. The assays were optimized to be statistically robust enough for screening. The first assay, based on crystal violet staining, measures total biofilm biomass, and it was automated using a liquid handling workstation to decrease the manual workload and signal variation. The second assay, based on resazurin staining, measures viability of the biofilm, and it was thoroughly optimized for the strain used, but was then a very simple and fast method to be used for primary screening. The fluorescent resazurin probe is not toxic to the biofilms. In fact, it was also shown in this project that staining the biofilms with resazurin prior to staining with crystal violet had no effect on the latter and they can be used in sequence on the same screening plate. This sequential addition step was indeed a major improvement on the use of reagents and consumables and also shortened the work time. As a third assay in the platform a wheat germ agglutinin based assay was added to evaluate the effect a compound has on the EPS layer. Using this assay it was found that even if compounds might have clear effect on both biomass and viability, the EPS layer can be left untouched or even be increased. This is a clear implication of the importance of using several assays to be able to find “true hits” in a screening setting. In the pilot study of screening for antimicrobial and anti-biofilm effects using a cinchona alkaloid library, one compound was found to have antimicrobial effect against planktonic bacteria and prevent biofilm formation at low micromolar concentration. To eradicate biofilms, a higher concentration was needed. It was also shown that the chemical space occupied by the active compound was slightly different than the rest of the cinchona alkaloids as well as the rest of the compounds used for validatory screening during the optimization processes of the separate assays.

Testing Platform Development for Large Scale Solar Integration

Currently, a high penetration level of Distributed Generations (DGs) has been observed in the Danish distribution systems, and even more DGs are foreseen to be present in the upcoming years. How to utilize them for maintaining the security of the power supply under the emergency situations, has been of great interest for study. This master project is intended to develop a control architecture for studying purposes of distribution systems with large scale integration of solar power. As part of the EcoGrid EU Smart Grid project, it focuses on the system modelling and simulation of a Danish representative LV network located in Bornholm island. Regarding the control architecture, two types of reactive control techniques are implemented and compare. In addition, a network voltage control based on a tap changer transformer is tested. The optimized results after applying a genetic algorithm to five typical Danish domestic loads are lower power losses and voltage deviation using Q(U) control, specially with large consumptions. Finally, a communication and information exchange system is developed with the objective of regulating the reactive power and thereby, the network voltage remotely and real-time. Validation test of the simulated parameters are performed as well.

Heat flux measurement inside internal combustion engine with gradient heat flux sensor.

This master’s thesis is devoted to study different heat flux measurement techniques such as differential temperature sensors, semi-infinite surface temperature methods, calorimetric sensors and gradient heat flux sensors. The possibility to use Gradient Heat Flux Sensors (GHFS) to measure heat flux in the combustion chamber of compression ignited reciprocating internal combustion engines was considered in more detail. A. Mityakov conducted an experiment, where Gradient Heat Flux Sensor was placed in four stroke diesel engine Indenor XL4D to measure heat flux in the combustion chamber. The results which were obtained from the experiment were compared with model’s numerical output. This model (a one – dimensional single zone model) was implemented with help of MathCAD and the result of this implementation is graph of heat flux in combustion chamber in relation to the crank angle. The values of heat flux throughout the cycle obtained with aid of heat flux sensor and theoretically were sufficiently similar, but not identical. Such deviation is rather common for this type of experiment.

One process to rule them all? The role of a repository platform in the management of digitized cultural heritage at the National Library of Finland

Presentation at Open Repositories 2013, DSpace User Group, on 12.7.2013 in Charlottetown, PEI, Canada

Reusable formal architectures for networked systems

Today's networked systems are becoming increasingly complex and diverse. The current simulation and runtime verification techniques do not provide support for developing such systems efficiently; moreover, the reliability of the simulated/verified systems is not thoroughly ensured. To address these challenges, the use of formal techniques to reason about network system development is growing, while at the same time, the mathematical background necessary for using formal techniques is a barrier for network designers to efficiently employ them. Thus, these techniques are not vastly used for developing networked systems. The objective of this thesis is to propose formal approaches for the development of reliable networked systems, by taking efficiency into account. With respect to reliability, we propose the architectural development of correct-by-construction networked system models. With respect to efficiency, we propose reusable network architectures as well as network development. At the core of our development methodology, we employ the abstraction and refinement techniques for the development and analysis of networked systems. We evaluate our proposal by employing the proposed architectures to a pervasive class of dynamic networks, i.e., wireless sensor network architectures as well as to a pervasive class of static networks, i.e., network-on-chip architectures. The ultimate goal of our research is to put forward the idea of building libraries of pre-proved rules for the efficient modelling, development, and analysis of networked systems. We take into account both qualitative and quantitative analysis of networks via varied formal tool support, using a theorem prover the Rodin platform and a statistical model checker the SMC-Uppaal.

Synthesis, characterization and chemical sensor application of conducting polymers

Polymeric materials that conduct electricity are highly interesting for fundamental studies and beneficial for modern applications in e.g. solar cells, organic field effect transistors (OFETs) as well as in chemical and bio‐sensing. Therefore, it is important to characterize this class of materials with a wide variety of methods. This work summarizes the use of electrochemistry also in combination with spectroscopic methods in synthesis and characterization of electrically conducting polymers and other π‐conjugated systems. The materials studied in this work are intended for organic electronic devices and chemical sensors. Additionally, an important part of the presented work, concerns rational approaches to the development of water‐based inks containing conducting particles. Electrochemical synthesis and electroactivity of conducting polymers can be greatly enhanced in room temperature ionic liquids (RTILs) in comparison to conventional electrolytes. Therefore, poly(para‐phyenylene) (PPP) was electrochemically synthesized in the two representative RTILs: bmimPF6 and bmiTf2N (imidazolium and pyrrolidinium‐based salts, respectively). It was found that the electrochemical synthesis of PPP was significantly enhanced in bmimPF6. Additionally, the results from doping studies of PPP films indicate improved electroactivity in bmimPF6 during oxidation (p‐doping) and in bmiTf2N in the case of reduction (n‐doping). These findings were supported by in situ infrared spectroscopy studies. Conducting poly(benzimidazobenzophenanthroline) (BBL) is a material which can provide relatively high field‐effect mobility of charge carriers in OFET devices. The main disadvantage of this n‐type semiconductor is its limited processability. Therefore in this work BBL was functionalized with poly(ethylene oxide) PEO, varying the length of side chains enabling water dispersions of the studied polymer. It was found that functionalization did not distract the electrochemical activity of the BBL backbone while the processability was improved significantly in comparison to conventional BBL. Another objective was to study highly processable poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) water‐based inks for controlled patterning scaled‐down to nearly a nanodomain with the intention to fabricate various chemical sensors. Developed PEDOT:PSS inks greatly improved printing of nanoarrays and with further modification with quaternary ammonium cations enabled fabrication of PEDOT:PSS‐based chemical sensors for lead (II) ions with enhanced adhesion and stability in aqueous environments. This opens new possibilities for development of PEDOT:PSS films that can be used in bio‐related applications. Polycyclic aromatic hydrocarbons (PAHs) are a broad group of π‐conjugated materials consisting of aromatic rings in the range from naphthalene to even hundred rings in one molecule. The research on this type of materials is intriguing, due to their interesting optical properties and resemblance of graphene. The objective was to use electrochemical synthesis to yield relatively large PAHs and fabricate electroactive films that could be used as template material in chemical sensors. Spectroscopic, electrochemical and electrical investigations evidence formation of highly stable films with fast redox response, consisting of molecules with 40 to 60 carbon atoms. Additionally, this approach in synthesis, starting from relatively small PAH molecules was successfully used in chemical sensor for lead (II).

Probabilistic position and orientation estimation of rigid objects using an RGB-D sensor

The recent emergence of low-cost RGB-D sensors has brought new opportunities for robotics by providing affordable devices that can provide synchronized images with both color and depth information. In this thesis, recent work on pose estimation utilizing RGBD sensors is reviewed. Also, a pose recognition system for rigid objects using RGB-D data is implemented. The implementation uses half-edge primitives extracted from the RGB-D images for pose estimation. The system is based on the probabilistic object representation framework by Detry et al., which utilizes Nonparametric Belief Propagation for pose inference. Experiments are performed on household objects to evaluate the performance and robustness of the system.

Backpacker 2.0 - Contemporary backpackers and their use of social media as an information and communication platform

Long-term independent budget travel to countries far away has become increasingly common over the last few decades, and backpacking has now entered the tourism mainstream. Nowadays, backpackers are a very important segment of the global travel market. Backpacking is a type of tourism that involves a lot of information search activities. The Internet has become a major source of information as well as a platform for tourism business transactions. It allows travelers to gain information very effortlessly and to learn about tourist destinations and products directly from other travelers in the form of electronic word-of-mouth (eWOM). Social media has penetrated and changed the backpacker market, as now modern travelers can stay connected to people at home, read online recommendations, and organize and book their trips very independently. In order to create a wider understanding on modern-day backpackers and their information search and share behavior in the Web 2.0 era, this thesis examined contemporary backpackers and their use of social media as an information and communication platform. In order to achieve this goal, three sub-objectives were identified: 1. to describe contemporary backpacker tourism 2. to examine contemporary backpackers’ travel information search and share behavior 3. to explore the impacts of new information and communications technologies and Web 2.0 on backpacker tourism The empirical data was gathered with an online survey, thus the method of analysis was mainly quantitative, and a qualitative method was used for a brief analysis of open questions. The research included both descriptive and analytical approaches, as the goal was to describe modern-day backpackers, and to examine possible interdependencies between information search and share behavior and background variables. The interdependencies were tested for statistical significance with the help of five research hypotheses. The results suggested that backpackers no longer fall under the original backpacker definitions described some decades ago. Now, they are mainly short-term travelers, whose trips resemble more those of mainstream tourists. They use communication technologies very actively, and particularly social media. Traditional information sources, mainly guide books and recommendations from friends, are of great importance to them but also eWOM sources are widely used in travel decision making. The use of each source varies according to the stage of the trip. All in all, Web 2.0 and new ICTs have transformed the backpacker tourism industry in many ways. Although the experience has become less authentic in some travelers’ eyes, the backpacker culture is still recognizable.

A distributed, cloud-ready, digital content processing and transformation platform and a specific use case

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Invenio as a Blog Archiving platform

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014