Effect of thermal annealing on Fe40Ni38B18Mo4 thin films: modified Herzer model for magnetic evolution

Magnetic properties of nano-crystalline soft magnetic alloys have usually been correlated to structural evolution with heat treatment. However, literature reports pertaining to the study of nano-crystalline thin films are less abundant. Thin films of Fe40Ni38B18Mo4 were deposited on glass substrates under a high vacuum of ≈ 10−6 Torr by employing resistive heating. They were annealed at various temperatures ranging from 373 to 773K based on differential scanning calorimetric studies carried out on the ribbons. The magnetic characteristics were investigated using vibrating sample magnetometry. Morphological characterizations were carried out using atomic force microscopy (AFM), and magnetic force microscopy (MFM) imaging is used to study the domain characteristics. The variation of magnetic properties with thermal annealing is also investigated. From AFM and MFM images it can be inferred that the crystallization temperature of the as-prepared films are lower than their bulk counterparts. Also there is a progressive evolution of coercivity up to 573 K, which is an indication of the lowering of nano-crystallization temperature in thin films. The variation of coercivity with the structural evolution of the thin films with annealing is discussed and a plausible explanation is provided using the modified random anisotropy model

Magnetic and topographical modifications of amorphous Co–Fe thin films induced by high energy Ag7+ ion irradiation

We have investigated the effects of swift heavy ion irradiation on thermally evaporated 44 nm thick, amorphous Co77Fe23 thin films on silicon substrates using 100 MeV Ag7+ ions fluences of 1 1011 ions/ cm2, 1 1012 ions/cm2, 1 1013 ions/cm2, and 3 1013 ions/cm2. The structural modifications upon swift heavy irradiation were investigated using glancing angle X-ray diffraction. The surface morphological evolution of thin film with irradiation was studied using Atomic Force Microscopy. Power spectral density analysis was used to correlate the roughness variation with structural modifications investigated using X-ray diffraction. Magnetic measurements were carried out using vibrating sample magnetometry and the observed variation in coercivity of the irradiated films is explained on the basis of stress relaxation. Magnetic force microscopy images are subjected to analysis using the scanning probe image processor software. These results are in agreement with the results obtained using vibrating sample magnetometry. The magnetic and structural properties are correlated

Evolution of structural and magnetic properties of Co–Fe based metallic glass thin films with thermal annealing

Ultra thin films based on CoFe were prepared from a composite target employing thermal evaporation. The microstructure of the films was modified by thermal annealing. The relationship between microstructure and magnetic properties of the films was investigated using techniques like glancing angle X-ray diffraction (GXRD), transmission electron microscopy (TEM) and vibrating sample magnetometry (VSM). The GXRD and TEM investigations showed an onset of crystallization of CoFe at around 373 K. The magnetic softness of the films improved with thermal annealing but at higher annealing temperature it is found to be deteriorating. Annealing inducedmodification of surface morphology of the alloy thin filmswas probed by atomic force microscopy (AFM). Surface smoothening was observed with thermal annealing and the observed magnetic properties correlate well with surface modifications induced by thermal annealing

Goldnanoteilchen auf Titandioxid

In dieser Arbeit wurde das Wachstum sowie die ultraschnelle Elektronendynamik des Oberflächenplasmon Polaritons von Goldnanoteilchen auf Titandioxid untersucht. Die Messung der Dephasierungszeit des Oberflächenplasmons von Nanoteilchen mit definierter Form und Größe erfolgte dabei mit der Methode des spektralen Lochbrennens. Die Nanoteilchen wurden durch Deposition von Goldatomen aus einem thermischen Atomstrahl mit anschließender Diffussion und Nukleation, d.h. Volmer-Weber-Wachstum, auf Titandioxidsubstraten hergestellt und mittels einer Kombination aus optischer Spektroskopie und Rasterkraftmikroskopie systematisch untersucht. Dabei lässt sich das Nanoteilchenensemble durch das mittlere Achsverhältnis und den mittleren Äquivalentradius charakterisieren. Die Messungen zeigen, dass die Proben große Größen- und Formverteilungen aufweisen und ein definierter Zusammenhang zwischen Größe und Form der Teilchen existiert. Während kleine Goldnanoteilchen nahezu kugelförmig sind, flachen die Teilchen mit zunehmender Größe immer mehr ab. Des Weiteren wurde in dieser Arbeit die Methode des lasergestützten Wachstums auf das System Gold auf Titandioxid angewendet. Systematische Untersuchungen zeigten, dass sich das Achsverhältnis der Teilchen durch geeignete Wahl von Photonenenergie und Fluenz des eingestrahlten Laserlichts definiert und gezielt vorgeben lässt. Die Methode des lasergestützten Wachstums erschließt damit den Bereich außerhalb der Zugänglichkeit des natürlichen Wachstums. Aufgrund der Formabhängigkeit der spektrale Lage der Plasmonresonanz ist man somit in der Lage, die optischen Eigenschaften der Nanoteilchen gezielt einzustellen und z.B. für technische Anwendungen zu optimieren. Die Untersuchung der ultraschnellen Elektronendynamik von Goldnanoteilchen auf Titandioxid mit äquivalenten Radien zwischen 8 bis 15 nm erfolgte in dieser Arbeit mit der Methode des spektralen Lochbrennes. Hierzu wurde die Dephasierungszeit des Oberflächenplasmons systematisch als Funktion der Photonenenergie in einem Bereich von 1,45 bis 1,85 eV gemessen. Es zeigte sich, dass die gemessenen Dephasierungszeiten von 8,5 bis 16,2 fs deutlich unter den in der dielektrischen Funktion von Gold enthaltenen Werten lagen, was den erwarteten Einfluss der reduzierten Dimension der Teilchen demonstriert. Um die Messwerte trotz verschiedener Teilchengrößen untereinander vergleichen und den Einfluss der intrinsischen Dämpfung quantifizieren zu können, wurde zusätzlich der Dämpfungsparameter A bestimmt. Die ermittelten A-Faktoren zeigten dabei eine starke Abhängigkeit von der Plasmonenergie. Für Teilchen mit Plasmonenergien von 1,45 bis 1,55 eV wurde ein Dämpfungsfaktor von A ~ 0,2 nm/fs ermittelt, der lediglich Oberflächenstreuung als dominierenden Dämpfungsmechanismus widerspiegelt. Hingegen wurde für Teilchen mit Plasmonenergien oberhalb von 1,55 eV ein drastischer Anstieg der Dämpfung auf A ~ 0,4 nm/fs beobachtet. Die erhöhte Dämpfung wurde dabei dem zusätzlichen Vorliegen einer chemischen Dämpfung durch das Titandioxidsubstrat zugeschrieben. Zusammenfassend zeigen die Ergebnisse somit, dass eine starke Abhängigkeit der chemischen Dämpfung von der Photonenenergie vorliegt. Es konnte erstmals nachgewiesen werden, dass die chemische Dämpfung erst ab einer bestimmten unteren Schwelle der Photonenenergie einsetzt, die für Goldnanoteilchen auf Titandioxid bei etwa 1,6 eV liegt.

Development of hybrid UV VCSEL with organic active material and dielectric DBR mirrors for medical, sensoric and data storage applications

Lasers play an important role for medical, sensoric and data storage devices. This thesis is focused on design, technology development, fabrication and characterization of hybrid ultraviolet Vertical-Cavity Surface-Emitting Lasers (UV VCSEL) with organic laser-active material and inorganic distributed Bragg reflectors (DBR). Multilayer structures with different layer thicknesses, refractive indices and absorption coefficients of the inorganic materials were studied using theoretical model calculations. During the simulations the structure parameters such as materials and thicknesses have been varied. This procedure was repeated several times during the design optimization process including also the feedback from technology and characterization. Two types of VCSEL devices were investigated. The first is an index coupled structure consisting of bottom and top DBR dielectric mirrors. In the space in between them is the cavity, which includes active region and defines the spectral gain profile. In this configuration the maximum electrical field is concentrated in the cavity and can destroy the chemical structure of the active material. The second type of laser is a so called complex coupled VCSEL. In this structure the active material is placed not only in the cavity but also in parts of the DBR structure. The simulations show that such a distribution of the active material reduces the required pumping power for reaching lasing threshold. High efficiency is achieved by substituting the dielectric material with high refractive index for the periods closer to the cavity. The inorganic materials for the DBR mirrors have been deposited by Plasma- Enhanced Chemical Vapor Deposition (PECVD) and Dual Ion Beam Sputtering (DIBS) machines. Extended optimizations of the technological processes have been performed. All the processes are carried out in a clean room Class 1 and Class 10000. The optical properties and the thicknesses of the layers are measured in-situ by spectroscopic ellipsometry and spectroscopic reflectometry. The surface roughness is analyzed by atomic force microscopy (AFM) and images of the devices are taken with scanning electron microscope (SEM). The silicon dioxide (SiO2) and silicon nitride (Si3N4) layers deposited by the PECVD machine show defects of the material structure and have higher absorption in the ultra violet range compared to ion beam deposition (IBD). This results in low reflectivity of the DBR mirrors and also reduces the optical properties of the VCSEL devices. However PECVD has the advantage that the stress in the layers can be tuned and compensated, in contrast to IBD at the moment. A sputtering machine Ionsys 1000 produced by Roth&Rau company, is used for the deposition of silicon dioxide (SiO2), silicon nitride (Si3N4), aluminum oxide (Al2O3) and zirconium dioxide (ZrO2). The chamber is equipped with main (sputter) and assisted ion sources. The dielectric materials were optimized by introducing additional oxygen and nitrogen into the chamber. DBR mirrors with different material combinations were deposited. The measured optical properties of the fabricated multilayer structures show an excellent agreement with the results of theoretical model calculations. The layers deposited by puttering show high compressive stress. As an active region a novel organic material with spiro-linked molecules is used. Two different materials have been evaporated by utilizing a dye evaporation machine in the clean room of the department Makromolekulare Chemie und Molekulare Materialien (mmCmm). The Spiro-Octopus-1 organic material has a maximum emission at the wavelength λemission = 395 nm and the Spiro-Pphenal has a maximum emission at the wavelength λemission = 418 nm. Both of them have high refractive index and can be combined with low refractive index materials like silicon dioxide (SiO2). The sputtering method shows excellent optical quality of the deposited materials and high reflection of the multilayer structures. The bottom DBR mirrors for all VCSEL devices were deposited by the DIBS machine, whereas the top DBR mirror deposited either by PECVD or by combination of PECVD and DIBS. The fabricated VCSEL structures were optically pumped by nitrogen laser at wavelength λpumping = 337 nm. The emission was measured by spectrometer. A radiation of the VCSEL structure at wavelength 392 nm and 420 nm is observed.

Development of directly modulated high speed telecommunication lasers based on surface defined feedback gratings

High-speed semiconductor lasers are an integral part in the implemen- tation of high-bit-rate optical communications systems. They are com- pact, rugged, reliable, long-lived, and relatively inexpensive sources of coherent light. Due to the very low attenuation window that exists in the silica based optical fiber at 1.55 μm and the zero dispersion point at 1.3 μm, they have become the mainstay of optical fiber com- munication systems. For the fabrication of lasers with gratings such as, distributed bragg reflector or distributed feedback lasers, etching is the most critical step. Etching defines the lateral dimmensions of the structure which determines the performance of optoelectronic devices. In this thesis studies and experiments were carried out about the exist- ing etching processes for InP and a novel dry etching process was de- veloped. The newly developed process was based on Cl2/CH4/H2/Ar chemistry and resulted in very smooth surfaces and vertical side walls. With this process the grating definition was significantly improved as compared to other technological developments in the respective field. A surface defined grating definition approach is used in this thesis work which does not require any re-growth steps and makes the whole fabrication process simpler and cost effective. Moreover, this grating fabrication process is fully compatible with nano-imprint lithography and can be used for high throughput low-cost manufacturing. With usual etching techniques reported before it is not possible to etch very deep because of aspect ratio dependent etching phenomenon where with increasing etch depth the etch rate slows down resulting in non-vertical side walls and footing effects. Although with our de- veloped process quite vertical side walls were achieved but footing was still a problem. To overcome the challenges related to grating defini- tion and deep etching, a completely new three step gas chopping dry etching process was developed. This was the very first time that a time multiplexed etching process for an InP based material system was demonstrated. The developed gas chopping process showed extra ordinary results including high mask selectivity of 15, moderate etch- ing rate, very vertical side walls and a record high aspect ratio of 41. Both the developed etching processes are completely compatible with nano imprint lithography and can be used for low-cost high-throughput fabrication. A large number of broad area laser, ridge waveguide laser, distributed feedback laser, distributed bragg reflector laser and coupled cavity in- jection grating lasers were fabricated using the developed one step etch- ing process. Very extensive characterization was done to optimize all the important design and fabrication parameters. The devices devel- oped have shown excellent performance with a very high side mode suppression ratio of more than 52 dB, an output power of 17 mW per facet, high efficiency of 0.15 W/A, stable operation over temperature and injected currents and a threshold current as low as 30 mA for almost 1 mm long device. A record high modulation bandwidth of 15 GHz with electron-photon resonance and open eye diagrams for 10 Gbps data transmission were also shown.

Optimization in the Technological Steps for the Fabrication of Large Area Micromirror Arrays

Micromirror arrays are a very strong candidate for future energy saving applications. Within this work, the fabrication process for these micromirror arrays has been optimized and some steps for the large area fabrication of micromirror modules were performed. At first the surface roughness of the insulation layer of silicon dioxide (SiO2) was investigated. This SiO2 thin layer was deposited on three different type of substrates i.e. silicon, glass and Polyethylene Naphthalate (PEN) substrates. The deposition techniques which has been used are Plasma Enhanced Chemical Vapor Deposition (PECVD), Physical Vapor Deposition (PVD) and Ion Beam Sputter Deposition (IBSD). The thickness of the SiO2 thin layer was kept constant at 150nm for each deposition process. The surface roughness was measured by Stylus Profilometry and Atomic Force Microscopy (AFM). It was found that the layer which was deposited by IBSD has got the minimum surface roughness value and the layer which was deposited by PECVD process has the highest surface roughness value. During the same investigation, the substrate temperature of PECVD was varied from 80° C to 300° C with the step size of 40° C and it was found that the surface roughness keeps on increasing as the substrate holder temperature increases in the PECVD process. A new insulation layer system was proposed to minimize the dielectric breakdown effect in insulation layer for micromirror arrays. The conventional bilayer system was replaced by five layer system but the total thickness of insulation layer remains the same. It was found that during the actuation of micromirror arrays structure, the dielectric breakdown effect was reduced considerably as compared to the bilayer system. In the second step the fabrication process of the micromirror arrays was successfully adapted and transferred from glass substrates to the flexible PEN substrates by optimizing the conventional process recipe. In the last section, a large module of micromirror arrays was fabricated by electrically interconnecting four 10cm×10cm micromirror modules on a glass pane having dimensions of 21cm×21cm.

The Effect of Periodic Silane Burst on the Properties of GaN on Si (111) Substrates

The periodic silane burst technique was employed during metalorganic chemical vapor deposition of epitaxial GaN on AlN buffer layers grown on Si (111). Periodic silicon delta doping during growth of both the AlN and GaN layers led to growth of GaN films with decreased tensile stresses and decreased threading dislocation densities, as well as films with improved quality as indicated by x-ray diffraction, micro-Raman spectroscopy, atomic force microscopy, and transmission electron microscopy. The possible mechanism of the reduction of tensile stress and the dislocation density is discussed in the paper.

Validity of the self-report on drug use by university studentes : correspondence between self-reported use and use detected in urine

Resumen tomado de la publicaci??n

Efectos del consumo de cigarrillo en la presentación y severidad de la dismenorrea

Introducción: La dismenorrea se presenta como una patología cada vez más frecuente en mujeres de 16-30 años. Dentro de los factores asociados a su presentación, el consumo de tabaco ha revelado resultados contradictorios. El objetivo del presente estudio es explorar la asociación entre el consumo de cigarrillo y la presentación de dismenorrea, y determinar si los trastornos del ánimo y la depresión, alteran dicha asociación. Materiales y métodos: Se realizó un estudio de prevalencia analítica en mujeres de la Universidad del Rosario matriculadas en pregrado durante el primer semestre de 2013, para determinar la asociación entre el consumo de tabaco y la presentación de dismenorrea. En el estudio se tuvieron en cuenta variables tradicionalmente relacionadas con dismenorrea, incluyendo las variables ansiedad y depresión como potenciales variables de confusión. Los registros fueron analizados en el programa Estadístico IBM SPSS Statistics Versión 20.0. Resultados: Se realizaron 538 cuestionarios en total. La edad promedio fue 19.92±2.0 años. La prevalencia de dismenorrea se estimó en 89.3%, la prevalencia de tabaquismo 11.7%. No se encontró una asociación entre dismenorrea y tabaquismo (OR 3.197; IC95% 0.694-14.724). Dentro de las variables analizadas, la depresión y la ansiedad constituyen factores de riesgo independientes para la presentación de dismenorrea con una asociación estadísticamente significativa p=0.026 y p=0.024 respectivamente. El análisis multivariado encuentra como factor determinante en la presentación de dismenorrea, la interacción de depresión y ansiedad controlando por las variables tradicionales p<0.0001. Sin embargo, esta asociación se pierde cuando se analiza en la categoría de dismenorrea severa y gana relevancia el uso de métodos de anticoncepción diferentes a los hormonales, mientras que el hecho de haber iniciado la vida sexual presenta una tendencia limítrofe de riesgo. Conclusiones: No se puede demostrar que el tabaco es un factor asociado a la presentación de dismenorrea. Los trastornos del ánimo y la ansiedad constituyen factores determinantes a la presentación de dismenorrea independientemente de la presencia de otros concomitantes. Las variables de asociación se modifican cuando la variable dependiente se categoriza en su estado más severo. Se necesitan estudios más amplios y detallados para establecer dicha asociación.

La influencia del autoconcepto en el rendimiento académico en estudiantes universitarios. 'The influence of self-concept on academic achievement in university students'.

Resumen tomado de la publicación. Con el apoyo económico del departamento MIDE de la UNED. Incluye anexo con el cuestionario utilizado para la realización del estudio

A study on the phylogeny and the ecology of ammonia-oxidizing bacteria using a new molecular marker based on the gene amoB

L'agricultura i la industrialització han causat un augment significatiu del nombre d'ambients rics en amoni. La presència de compostos nitrogenats redueix la qualitat de l'aigua, causant problemes de toxicitat, deteriorant el medi ambient i fins i tot afectant la salut humana. En conseqüència, la nitrificació s'ha convertit en un procés global que afecta al cicle del nitrogen a la biosfera. Els bacteris oxidadors d'amoni (AOB) són els responsables de l'oxidació de l'amoni a nitrit, i juguen un paper essencial en el cicle del nitrogen. Els primers oxidadors d'amoni foren aïllats a finals del segle XIX, però la lentitud del seu creixement i les dificultats per cultivar-los feren que fins als anys 80, amb els primers estudis emprant el gen 16SrDNA, no s'assolís un coneixement complert d'aquest grup bacterià. Actualment les bases de dades contenen multitud d'entrades amb seqüències corresponents a AOB. L'objectiu d'aquest treball era trobar, desenvolupar i avaluar eines útils i fiables per a l'estudi dels AOB en mostres ambientals. En aquest treball primer descrivim la utilització de la hibridació in situ amb fluorescència (FISH), mitjançant l'aplicació de sondes amb diana en el 16SrRNA dels AOB. La FISH ens va permetre detectar i recomptar aquest grup bacterià; no obstant, aquest mètode no permetia la detecció de noves seqüències, pel que es necessitava una nova eina. Amb aquesta intenció vam aplicar la seqüència de la sonda Nso1225 en una PCR. El fet d'amplificar específicament un fragment del 16SrDNA dels AOB va suposar el desenvolupament d'una nova eina molecular que permetia detectar la presència i diversitat d'aquests bacteris en ambients naturals. Malgrat tot, algunes seqüències pertanyents a bacteris no oxidadors d'amoni del subgrup β dels proteobacteris, eren també obtingudes amb aquesta tècnica. Així mateix, un dels inconvenients de l'ús del 16SrDNA com a marcador és la impossibilitat de detectar simultàniament els AOB que pertanyen als subgrups β i γ dels proteobacteris. El gen amoA, que codifica per la subunitat A de l'enzim amoni monooxigenasa (AMO), era aleshores àmpliament utilitzat com a marcador per a la detecció dels AOB. En aquest treball també descrivim la utilització d'aquest marcador en mostres procedents d'un reactor SBR. Aquest marcador ens va permetre identificar seqüències de AOB en la mostra, però la necessitat de detectar amoA mitjançant clonatge fa que l'ús d'aquest marcador requereixi massa temps per a la seva utilització com a eina en estudis d'ecologia microbiana amb moltes mostres. Per altra banda, alguns autors han assenyalat l'obtenció de seqüències de no AOB en utilitzar amoA en un protocol de PCR-DGGE. Amb la finalitat d'obtenir una eina ràpida i rigorosa per detectar i identificar els AOB, vam desenvolupar un joc nou d'oligonucleòtids amb diana en el gen amoB, que codifica per a la subunitat transmembrana de l'enzim AMO. Aquest gen ha demostrat ser un bon marcador molecular pels AOB, oferint, sense tenir en compte afiliacions filogenètiques, una elevada especificitat, sensibilitat i fiabilitat. En aquest treball també presentem una anàlisi de RT-PCR basada en la detecció del gen amoB per a la quantificació del gènere Nitrosococcus. El nou joc d'oligonucleòtids dissenyat permet una enumeració altament específica i sensible de tots els γ-Nitrosococcus coneguts. Finalment, vam realitzar un estudi poligènic, comparant i avaluant els marcadors amoA, amoB i 16SrDNA, i vàrem construir un arbre filogenètic combinat. Com a resultat concloem que amoB és un marcador adequat per a la detecció i identificació dels AOB en mostres ambientals, proporcionant alhora agrupacions consistents en fer inferències filogenètiques. Per altra banda, la seqüència sencera del gen 16S rDNA és indicada com a marcador en estudis amb finalitats taxonòmiques i filogenètiques en treballar amb cultius purs de AOB.

A review of the potential impacts of climate change on surface water quality

It is now accepted that some human-induced climate change is unavoidable. Potential impacts on water supply have received much attention, but relatively little is known about the concomitant changes in water quality. Projected changes in air temperature and rainfall could affect river flows and, hence, the mobility and dilution of contaminants. Increased water temperatures will affect chemical reaction kinetics and, combined with deteriorations in quality, freshwater ecological status. With increased flows there will be changes in stream power and, hence, sediment loads with the potential to alter the morphology of rivers and the transfer of sediments to lakes, thereby impacting freshwater habitats in both lake and stream systems. This paper reviews such impacts through the lens of UK surface water quality. Widely accepted climate change scenarios suggest more frequent droughts in summer, as well as flash-flooding, leading to uncontrolled discharges from urban areas to receiving water courses and estuaries. Invasion by alien species is highly likely, as is migration of species within the UK adapting to changing temperatures and flow regimes. Lower flows, reduced velocities and, hence, higher water residence times in rivers and lakes will enhance the potential for toxic algal blooms and reduce dissolved oxygen levels. Upland streams could experience increased dissolved organic carbon and colour levels, requiring action at water treatment plants to prevent toxic by-products entering public water supplies. Storms that terminate drought periods will flush nutrients from urban and rural areas or generate acid pulses in acidified upland catchments. Policy responses to climate change, such as the growth of bio-fuels or emission controls, will further impact freshwater quality.