The Flotation of Niobium Oxide Minerals from Carbonatite Ores

Global niobium production is presently dominated by three operations, Araxá and Catalão (Brazil), and Niobec (Canada). Although Brazil accounts for over 90% of the world’s niobium production, a number of high grade niobium deposits exist worldwide. The advancement of these deposits depends largely on the development of operable beneficiation flowsheets. Pyrochlore, as the primary niobium mineral, is typically upgraded by flotation with amine collectors at acidic pH following a complicated flowsheet with significant losses of niobium. This research compares the typical two stage flotation flowsheet to a direct flotation process (i.e. elimination of gangue pre-flotation) with the objective of circuit simplification. In addition, the use of a chelating reagent (benzohydroxamic acid, BHA) was studied as an alternative collector for fine grained, highly disseminated pyrochlore. For the amine based reagent system, results showed that while comparable at the laboratory scale, when scaled up to the pilot level the direct flotation process suffered from circuit instability because of high quantities of dissolved calcium in the process water due to stream recirculation and fine calcite dissolution, which ultimately depressed pyrochlore. This scale up issue was not observed in pilot plant operation of the two stage flotation process as a portion of the highly reactive carbonate minerals was removed prior to acid addition. A statistical model was developed for batch flotation using BHA on carbonatite ore (0.25% Nb2O5) that could not be effectively upgraded using the conventional amine reagent scheme. Results showed that it was possible to produce a concentrate containing 1.54% Nb2O5 with 93% Nb recovery in ~15% of the original mass. Fundamental studies undertaken included FT-IR and XPS, which showed the adsorption of both the protonized amine and the neutral amine onto the surface of the pyrochlore (possibly at niobium sites as indicated by detected shifts in the Nb3d binding energy). The results suggest that the preferential flotation of pyrochlore over quartz with amines at low pH levels can be attributed to a difference in critical hemimicelle concentration (CHC) values for the two minerals. BHA was found to be absorbed on pyrochlore surfaces by a similar mechanism to alkyl hydroxamic acid. It is hoped that this work will assist in improving operability of existing pyrochlore flotation circuits and help promote the development of niobium deposits globally. Future studies should focus on investigation into specific gangue mineral depressants and inadvertent activation phenomenon related to BHA flotation of gangue minerals.

Copyright and Parody:Taking Backward the Gowers Review

In 2006 the Gowers Review of Intellectual Property made a series of recommendations for reforming the intellectual property regime to better serve the interests of both consumers and industry. Among the proposed recommendations was that an exception for parody be introduced within the Copyright Designs and Patents Act 1988. In January 2008 the Intellectual Property Office (the IPO) launched the first part of a two-stage consultation process on exceptions to copyright. As part of that consultation process, the IPO proposed a ‘fair dealing style exception’ for parody, and sought views on whether a new exception should be introduced as well as what form it might take. In December 2009 the IPO launched the second stage of this consultation process. The second consultation document rejected the case for a new parody exception. This article considers the place of parody within the copyright regime and the objections levelled against the introduction of an exception set out within the IPO's second consultation document. It invites the IPO to reconsider its decision not to recommend the introduction of a specific exception for parody within the UK.

Time of Flight Measurements for Neutrons Produced in Reactions Driven by Laser-Target Interactions at Petawatt level

Abstract Short intense pulses of fast neutrons were produced in a two stage laser-driven experiment. Protons were accelerated by means of the Target Normal Sheath Acceleration (TNSA) method using the TITAN facility at the Lawrence Livermore National Laboratory. Neutrons were obtained following interactions of the protons with a secondary lithium fluoride (LiF) target. The properties of the neutron flux were studied using BC-400 plastic scintillation detectors and the neutron time of flight (nTOF) technique. The detector setup and the experimental conditions were simulated with the Geant4 toolkit. The effects of different components of the experimental setup on the nTOF were studied. Preliminary results from a comparison between experimental and simulated nTOF distributions are presented.

Raman Analysis of Dilute Aqueous Samples by Localized Evaporation of Submicroliter Droplets on the Tips of Superhydrophobic Copper Wires

Raman analysis of dilute aqueous solutions is normally prevented by their low signal levels. A very general method to increase the concentration to detectable levels is to evaporate droplets of the sample to dryness, creating solid deposits which are then Raman probed. Here, superhydrophobic (SHP) wires with hydrophilic tips have been used as supports for drying droplets, which have the advantage that the residue is automatically deposited at the tip. The SHP wires were readily prepared in minutes using electroless galvanic deposition of Ag onto copper wires followed by modification with a polyfluorothiol (3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-heptadecafluoro-1-decanethiol, HDFT). Cutting the coated wires with a scalpel revealed hydrophilic tips which could support droplets whose maximum size was determined by the wire diameter. Typically, 230 μm wires were used to support 0.6 μL droplets. Evaporation of dilute melamine droplets gave solid deposits which could be observed by scanning electron microscopy (SEM) and Raman spectroscopy. The limit of detection for melamine using a two stage evaporation procedure was 1 × 10^-6 mol dm^-3. The physical appearance of dried droplets of sucrose and glucose showed that the samples retained significant amounts of water, even under high vacuum. Nonetheless, the Raman detection limits of sucrose and glucose were 5 × 10^-4 and 2.5 × 10^-3 mol dm^-3, respectively, which is similar to the sensitivity reported for surface-enhanced Raman spectroscopy (SERS) detection of glucose. It was also possible to quantify the two sugars in mixtures at concentrations which were similar to those found in human blood through multivariate analysis.

In-situ formation of solidified hydrogen thin-membrane targets using a pulse tube cryocooler

An account is given of the Central Laser Facility's work to produce a cryogenic hydrogen targetry system using a pulse tube cryocooler. Due to the increasing demand for low Z thin laser targets, CLF (in collaboration with TUD) have been developing a system which allows the production of solid hydrogen membranes by engineering a design which can achieve this remotely; enabling the gas injection, condensation and solidification of hydrogen without compromising the vacuum of the target chamber. A dynamic sealing mechanism was integrated which allows targets to be grown and then remotely exposed to open vacuum for laser interaction. Further research was conducted on the survivability of the cryogenic targets which concluded that a warm gas effect causes temperature spiking when exposing the solidified hydrogen to the outer vacuum. This effect was shown to be mitigated by improving the pumping capacity of the environment and reducing the minimum temperature obtainable on the target mount. This was achieved by developing a two-stage radiation shield encased with superinsulating blanketing; reducing the base temperature from 14 0.5 K to 7.2 0.2 K about the coldhead as well as improving temperature control stability following the installation of a high-performance temperature controller and sensor apparatus. The system was delivered experimentally and in July 2014 the first laser shots were taken upon hydrogen targets in the Vulcan TAP facility.

Partial Cooperation in Location Choice: Salop’s Model with Three Firms

We consider how three firms compete in a Salop location model and how cooperation in location choice by two of these firms affects the outcomes. We con- sider the classical case of linear transportation costs as a two-stage game in which the firms select first a location on a unit circle along which consumers are dispersed evenly, followed by the competitive selection of a price. Standard analysis restricts itself to purely competitive selection of location; instead, we focus on the situation in which two firms collectively decide about location, but price their products competitively after the location choice has been effectuated. We show that such partial coordination of location is beneficial to all firms, since it reduces the number of equilibria significantly and, thereby, the resulting coordination problem. Subsequently, we show that the case of quadratic transportation costs changes the main conclusions only marginally.

Demonstration of passive plasma lensing of a laser wakefield accelerated electron bunch

We report on the first demonstration of passive all-optical plasma lensing using a two-stage setup. An intense femtosecond laser accelerates electrons in a laser wakefield accelerator (LWFA) to 100 MeVover millimeter length scales. By adding a second gas target behind the initial LWFAstage we introduce a robust and independently tunable plasma lens. We observe a density dependent reduction of the LWFA electron beam divergence from an initial value of 2.3 mrad, down to 1.4 mrad (rms), when the plasma lens is in operation. Such a plasma lens provides a simple and compact approach for divergence reduction well matched to the mm-scale length of the LWFA accelerator. The focusing forces are provided solely by the plasma and driven by the bunch itself only, making this a highly useful and conceptually new approach to electron beam focusing. Possible applications of this lens are not limited to laser plasma accelerators. Since no active driver is needed the passive plasma lens is also suited for high repetition rate focusing of electron bunches. Its understanding is also required for modeling the evolution of the driving particle bunch in particle driven wake field acceleration.

Crystallization on the Mesoscale : Self-Assembly of Iron Oxide Nanocubes into Mesocrystals

Self-assembly of nanoparticles is a promising route to form complex, nanostructured materials with functional properties. Nanoparticle assemblies characterized by a crystallographic alignment of the nanoparticles on the atomic scale, i.e. mesocrystals, are commonly found in nature with outstanding functional and mechanical properties. This thesis aims to investigate and understand the formation mechanisms of mesocrystals formed by self-assembling iron oxide nanocubes. We have used the thermal decomposition method to synthesize monodisperse, oleate-capped iron oxide nanocubes with average edge lengths between 7 nm and 12 nm and studied the evaporation-induced self-assembly in dilute toluene-based nanocube dispersions. The influence of packing constraints on the alignment of the nanocubes in nanofluidic containers has been investigated with small and wide angle X-ray scattering (SAXS and WAXS, respectively). We found that the nanocubes preferentially orient one of their {100} faces with the confining channel wall and display mesocrystalline alignment irrespective of the channel widths.  We manipulated the solvent evaporation rate of drop-cast dispersions on fluorosilane-functionalized silica substrates in a custom-designed cell. The growth stages of the assembly process were investigated using light microscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). We found that particle transport phenomena, e.g. the coffee ring effect and Marangoni flow, result in complex-shaped arrays near the three-phase contact line of a drying colloidal drop when the nitrogen flow rate is high. Diffusion-driven nanoparticle assembly into large mesocrystals with a well-defined morphology dominates at much lower nitrogen flow rates. Analysis of the time-resolved video microscopy data was used to quantify the mesocrystal growth and establish a particle diffusion-based, three-dimensional growth model. The dissipation obtained from the QCM-D signal reached its maximum value when the microscopy-observed lateral growth of the mesocrystals ceased, which we address to the fluid-like behavior of the mesocrystals and their weak binding to the substrate. Analysis of electron microscopy images and diffraction patterns showed that the formed arrays display significant nanoparticle ordering, regardless of the distinctive formation process.  We followed the two-stage formation mechanism of mesocrystals in levitating colloidal drops with real-time SAXS. Modelling of the SAXS data with the square-well potential together with calculations of van der Waals interactions suggests that the nanocubes initially form disordered clusters, which quickly transform into an ordered phase.

The Impact of Supervisory Monitoring On High-End Retail Sales Productivity

Based on a two-stage analysis of a panel of data on 12 outlets of a high-end retailer for 24 months, we investigate how the level of supervisory monitoring affects retail sales productivity. In the first stage, we use Data Envelopment Analysis (DEA) to compute the relative productivity of retail outlets in using their labor and capital resources to generate store sales. In the second stage, we regress the logarithm of DEA scores on contextual variables to obtain consistent estimators of the impact of contextual variables on productivity (Banker and Natarajan in Operation Research 56:48-58, 2008). Contrary to agency theoretic prediction that supervisory monitoring leads to an increase in retail sales productivity, our empirical results indicate that the higher the level of supervisory monitoring, the lower is the retail sales productivity for high-end retail outlets.

Economic Evaluations of State Policies

Thesis (Ph.D.)--University of Washington, 2016-08

Efeito da disponibilidade de oxigénio na produção de bioetanol por Scheffersomyces stipitis

O bioetanol constitui uma alternativa renovável aos combustíveis fósseis. Contudo, o bioetanol de primeira geração, produzido a partir de matérias-primas alimentares, desencadeou sérios problemas económicos e sociais, pelo que é fundamental encontrar estratégias que permitam a viabilidade comercial do bioetanol de segunda geração, produzido a partir de matérias-primas lenho-celulósicas. O licor de cozimento ao sulfito ácido de árvores folhosas (HSSL) é um subproduto da indústria papeleira que, devido ao seu elevado conteúdo em açúcares, pode ser utilizado como substrato para a produção de bioetanol de segunda geração. No entanto, a maior fração dos açúcares do HSSL é composta por pentoses. Por isso, a fermentação do HSSL é realizada pela levedura Scheffersomyces stipitis, pois esta é capaz de fermentar tanto as hexoses como as pentoses. Todavia, a S. stipitis só produz etanol sob condições microaerófilas, pelo que o maior desafio da produção de bioetanol por S. stipitis reside no estabelecimento das condições ótimas de arejamento. Este trabalho teve assim por objetivo estabelecer uma estratégia de arejamento que permita a eficiente produção de bioetanol a partir de HSSL por S. stipitis C4, a qual é uma estirpe adaptada a este substrato. Deste modo, foram realizados ensaios em Erlenmeyer, de modo a caracterizar o crescimento da S. stipitis C4, e ensaios em biorreator, com vista a estudar a produção de etanol por S. stipitis C4 em duas estratégias de arejamento diferentes. Na primeira estratégia foi usado apenas um único estágio de arejamento, com controlo da tensão de oxigénio dissolvido, DOT (%), e na segunda estratégia foram usados dois estágios de arejamento, com controlo da DOT no primeiro estágio e com restrição de oxigénio no segundo estágio. Nos ensaios em Erlenmeyer com HSSL o crescimento da S. stipitis C4 foi completamente inibido. Por sua vez, nos ensaios em biorreator com um único estágio de arejamento o controlo da DOT não permitiu a produção de etanol. No entanto, nos ensaios com dois estágios de arejamento em meio sintético foi possível produzir etanol de forma eficiente. Nesta estratégia, a utilização de um maior valor de DOT no primeiro estágio de arejamento permitiu aumentar a taxa específica de crescimento máxima e o rendimento em biomassa do primeiro estágio. Para além disso, a utilização de um maior valor de DOT no primeiro estágio também permitiu aumentar a produtividade em etanol durante o segundo estágio de arejamento. Por sua vez, no segundo estágio de arejamento verificou-se que a restrição de oxigénio evitou a reassimilação de etanol pela S. stipitis C4. Deste modo, os melhores resultados para a produção de etanol foram obtidos com controlo da DOT a 50% durante o primeiro estágio e com 0 mLAr.min-1 e 250 rpm durante o segundo estágio de arejamento. A aplicação desta estratégia de arejamento a 60% HSSL/40% meio sintético permitiu obter, no primeiro estágio de arejamento, uma taxa específica de crescimento máxima de 0,17 h-1, o que demonstra que a elevada disponibilidade de oxigénio durante o primeiro estágio aumenta a tolerância da S. stipitis C4 aos inibidores. Para além disso, a taxa volumétrica de produção de etanol e o rendimento em etanol de toda a fermentação foi de respetivamente de 0,03 g.L-1.h-1 e 0,38 g.g-1. Assim, a elevada eficiência de conversão dos açúcares em etanol (74,4%) demostra que a fermentação com dois estágios de arejamento constitui uma estratégia promissora para a produção de bioetanol de segunda geração a partir de HSSL.

Parallel partitioning of unstructured meshes

A method is outlined for optimising graph partitions which arise in mapping un- structured mesh calculations to parallel computers. The method employs a combination of iterative techniques to both evenly balance the workload and minimise the number and volume of interprocessor communications. They are designed to work efficiently in parallel as well as sequentially and when combined with a fast direct partitioning technique (such as the Greedy algorithm) to give an initial partition, the resulting two-stage process proves itself to be both a powerful and flexible solution to the static graph-partitioning problem. The algorithms can also be used for dynamic load-balancing and a clustering technique can additionally be employed to speed up the whole process. Experiments indicate that the resulting parallel code can provide high quality partitions, independent of the initial partition, within a few seconds.

Mesh partitioning and load balancing for distributed memory parallel systems

A method is outlined for optimising graph partitions which arise in mapping unstructured mesh calculations to parallel computers. The method employs a relative gain iterative technique to both evenly balance the workload and minimise the number and volume of interprocessor communications. A parallel graph reduction technique is also briefly described and can be used to give a global perspective to the optimisation. The algorithms work efficiently in parallel as well as sequentially and when combined with a fast direct partitioning technique (such as the Greedy algorithm) to give an initial partition, the resulting two-stage process proves itself to be both a powerful and flexible solution to the static graph-partitioning problem. Experiments indicate that the resulting parallel code can provide high quality partitions, independent of the initial partition, within a few seconds. The algorithms can also be used for dynamic load-balancing, reusing existing partitions and in this case the procedures are much faster than static techniques, provide partitions of similar or higher quality and, in comparison, involve the migration of a fraction of the data.

Recurrent gallstone ileus: case report and literature review

The gallstone ileus is a rare complication of cholelithiasis and it represents the 1-4% of small intestinal mechanical obstruction. Gallstone is generally wedged in the terminal ileum, even if unusual locations have been described. The literature reports a very high morbidity and mortality, often because misdiagnosis or delayed diagnosis. There is no unique opinion in literature about the choice between one-stage and two-stage surgery. We report a clinical case that summarizes the diagnostic and therapeutic difficulties of gallstone ileus.

Approximate ab initio calculations and the method of molecular fragments

A two stage approach to performing ab initio calculations on medium and large sized molecules is described. The first step is to perform SCF calculations on small molecules or molecular fragments using the OPIT Program. This employs a small basis set of spherical and p-type Gaussian functions. The Gaussian functions can be identified very closely with atomic cores, bond pairs, lone pairs, etc. The position and exponent of any of the Gaussian functions can be varied by OPIT to produce a small but fully optimised basis set. The second stage is the molecular fragments method. As an example of this, Gaussian exponents and distances are taken from an OPIT calculation on ethylene and used unchanged in a single SCF calculation on benzene. Approximate ab initio calculations of this type give much useful information and are often preferable to semi-empirical approaches, since the nature of the approximations involved is much better defined.