On optimizing micropower MOS regulated cascode circuits on switched current techniques

Trade-off between settling time and micropower consumption in MOS regulated cascode current sources as building parts in high-accuracy, current-switching D/A converters is analyzed. The regulation-loop frequency characteristic is obtained and difficulties to impose a dominant-pole condition to the resulting 2nd-order system are discussed. Raising pole frequencies while meeting consumption requirements is basically limited by parasitic capacitances. An alternative is found by imposing a twin-pole system in which design constraints are somewhat relaxed and settling slightly faster. Relationships between pole frequencies, transistor geometry and bias are established. Simulated waveforms obtained with PSpice of designed circuits following a voltage perturbation suggest a good agreement with theory. The proposed approach applied to the design of a micropower current-mode D/A converter improves its simulated settling performance.

Thermally activated dynamics of the tilts of the CuO6 octahedra, hopping of interstitial O, and possible instability towards the LTT phase in La2CuO4+δ

The anelastic spectrum (dynamic Young's modulus and elastic energy absorption) of La2CuO4+δ has been measured between 1 and 700 K with 0<δ<0.02. The spectrum of stoichiometric La2CuO4 in the low-temperature orthorhombic (LTO) phase is dominated by two intense relaxation processes which cause softenings of 16% around 150 K and 9% below 30 K at f∼1 kHz. The relaxation at 150 K is attributed to the presence of a fraction of the CuO6 octahedra which are able to change their tilted configuration by thermal activation between orientations which are nearly energetically equivalent, possibly within the twin boundaries. The relaxation below 30 K is governed by tunneling, and involves a considerable fraction of the lattice atoms. It is proposed that the double-well potentials for the low-temperature relaxation are created by the tendency of the LTO phase to form low-temperature tetragonal (LTT) domains, which however are not stabilized like when La is partially substituted with Ba. On doping with excess O, the relaxation rates of these processes are initially enhanced by hole doping, while their intensities are depressed by lattice disorder; an explanation of this behavior is provided. Excess O also causes two additional relaxation processes. The one appearing at lower values of δ is attributed to the hopping of single interstitial O2- ions, with a hopping rate equal to τ-1=2×10-14exp(-5600/T) s. The second process is slower and can be due to O pairs or other complexes containing excess O.

Morphological, mechanical and rheological properties of nylon 6/acrylonitrile-butadiene-styrene blends compatibilized with MMA/MA copolymers

The morphological, mechanical and rheological properties of nylon 6/acrylonitrile-butadiene-styrene blends compatibilized with MMA-MA [poly(methyl methacrylate-comaleic anhydride)] copolymers were studied. A twin screw extruder was used for melt-blended the polymers and the injection moulding process was used to mold the samples. The main focus was on nylon 6/ ABS blends compatibilized with one MMA-MA copolymer. This copolymer has PMMA segments that appear to be miscible with the styrene-acrylonitrile (SAN) phase of ABS and the anhydride groups can react with amine end groups of the nylon 6 (Ny6) to form graft copolymers at the interface between Ny6 and ABS rich phases. Tensile and impact and morphological properties were enhanced by the incorporation of this copolymer. Transmission electron microscopy (TEM) observations revealed that the ABS domains are finely dispersed in nylon 6 matrix and led to the lowest ductile-brittle transition temperatures and highest impact properties. It can be concluded that the MMA-MA copolymer is an efficient alternative for the reactive compatibilization and can be used as a compatibilizer for nylon 6/ABS blends.© 2003 Kluwer Academic Publishers.

Eucalyptus ESTs corresponding to the protoporphyrinogen IX oxidase enzyme related to the synthesis of heme, chlorophyll, and to the action of herbicides

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Implantation sites after embryo transfer into the central area of the uterine cavity

A total of 63 pregnancies (47 singleton, 15 twin, 1 triplet) from intracytoplasmic sperm injection cycles were analysed. In all embryo transfers, the catheter was introduced into the endometrial cavity guided by abdominal ultrasound, with the catheter tip placed at the middle point of the endometrial cavity. Gestational sacs (GS) were located 21-24 days after transfer (gestational age = 5 weeks) by two-dimensional and three-dimensional transvaginal ultrasound. The uterine cavity was divided into three parts: upper, middle and lower. Furthermore, the upper region was subdivided into right, middle and left areas, and the middle region was subdivided into right and left areas. The frequency of gestational sacs in each area was evaluated. In singleton pregnancies 66.0% (31/47) of the GS were detected in the upper region, 29.8% (14/47) in the middle region and 4.2% (2/47) in the lower region. In multiple pregnancies (twins and triplet) 45.5% (15/33) of the GS were detected in the upper region, 51.5% (17/33) in the middle region and 3.0% (1/33) in the lower region. In conclusion, the results demonstrate that when embryos are transferred to the central area of the uterine cavity there is an increase in implantation rate in the middle region compared with the rate expected in naturally conceived pregnancies (9-15%).

Cobertura da cultura da soja pela calda fungicida em função, de pontas de pulverização e volumes de aplicação

The goal of this research was to evaluate two tips of spraying nozzles (hollow cone nozzle and two flat fan nozzle annexed to a nozzle body DUO) and three spray volumes (100, 150 and 200 dm3 ha-1), whose application was for the control of the Asian soybean rust. An area of 288 m 2 was used, with a randomized blocks design in a factorial 2×3 with 4 repetitions, total of 24 experimental parcels of 12 m2. For the spraying with hydraulical nozzles a costal spray of constant pressure kept by C02 compressed with bar of 2 m was used. The analysis of the covering percentage was carried through by means of the use of hidro-sensible paper, that was placed in three position of the plant what it represents, in height, the third superior, average and inferior of the canopy. For both the third no interaction between the evaluated factors, was found and meither difference statistics between the spraying tips and the volumes. In absolute values the twin flat fan nozzle DUO presented minimum difference of covering in relation to the hollow cone nozzle, and for the spray volume of 200 dm3 ha -1 presented greater covering percentage.

Economic growth with equity: challenges for Latin America

Includes bibliography

Strengthening development: the interplay of macro- and microeconomics

Includes bibliography

Macroeconomic policies in times of crisis: options and perspectives

Includes bibliography

Prevention and insurance of conflict and terrorism: issues and evidence for Latin America

Includes bibliography

Description and genetic analysis of three sets of monozygotic twins resulting from transfers of single embryos to recipient mares

Case Description-3 sets of monozygotic twins resulting from transfers of single embryos to recipient mares were examined. Clinical Findings-In all 3 recipient mares with twin pregnancies, only 1 embryonic vesicle was detected before day 25 of gestation. In 1 recipient mare, 2 apparent adjacent vesicles, each containing an embryo with a heartbeat, were visualized on ultrasonographic examination on day 37 of gestation. The other 2 recipient mares underwent ultrasonographic examination on day 30 of gestation, at which time only 1 vesicle and embryo was identified. In these latter 2 recipient mares, however, a thorough ultrasonographic examination for a second conceptus on day 30 had not been performed, as only 1 embryo had been transferred and visualized on early ultrasonographic examination. Treatment and Outcome-All twin pregnancies resulted in death of both fetuses. Genetic analysis confirmed that each set of monozygotic twins originated from the transferred embryo. Clinical Relevance-Monozygotic twin pregnancy may occur after embryo transfer; thus recipient mares should be examined thoroughly for multiple conceptuses, especially between 25 and 30 days of gestation. At this time, the allantoides of monozygotic twins should be visible ultrasonographically and effective management may still be possible.

Risk factors for low birth weight in Botucatu city, SP state, Brazil: A study conducted in the public health system from 2004 to 2008

Background: Low birth weight (LBW), defined as birth weight less than 2500 g, has a complex etiology and may be a result of premature interruption of pregnancy or intrauterine growth restriction. The objective of this study was to provide information on determinants of LBW and contribute to the understanding of the problem in Brazil. Methods. A case-control study was conducted in Botucatu city, SP state, Brazil. The study population consisted of 2 groups with 860 newborns in each group as follows: low weight newborns (LWNB) and a control group (weight ≤ 2500 g). Secondary data from 2004 to 2008 were collected using the Live Birth Certificate (LBC) and records from medical charts of pregnant women in Basic Health Units (BHU) and in the Public University Hospital (UH). Variables were as follows: maternal socio-demographic characteristics, pregnancy and birth conditions including quality of prenatal care according to 3 criteria. They were based on parameters established by the Ministry of Health (MH), one of them, the modified Kessner Index. The multivariable analysis by logistic regression was used to evaluate the association between variables and LBW. Results: According to the analysis, the factors associated with LBW were as follows: prematurity (OR = 56.98, 95% CI 29.52-109.95), twin pregnancy (OR = 20.00, 95% CI 6.25-100.00), maternal smoking (OR = 2.12, 95% CI 1.33-3.45), maternal malnourishment (OR = 2.30, 95% CI 1.08-5.00), maternal obesity (OR = 2.30, 95% IC 1.18-4.48), weight gain during pregnancy less than 5 kg (OR = 2.63, 95% CI 1.35-5.00) and weight gain during pregnancy more than 15 kg (OR = 2.26, 95% CI 1.16-4.41). Adequacy of prenatal care visits adjusted to gestational age was less frequent in the LBW group than in the control group (68.7% vs. 80.5%, x 2 p < 0.001). According to the modified Kessner Index, 64.4% of prenatal visits in the LWNB group were adequate. Conclusion: LWNB are a quite heterogeneous group of infants concerning their determinants and prevention actions against LBW and the follow-up of these infants have also been very complex. Therefore, improvement in the quality of care provided should be given priority through concrete actions for prevention of LBW. © 2012 Fonseca et al; licensee BioMed Central Ltd.

Photodynamic therapy for pythiosis

Background -  Pythiosis is a life-threatening disease caused by Pythium insidiosum. Photodynamic therapy (PDT) is an alternative treatment to surgery that uses the interaction of a photosensitizer, light and molecular oxygen to cause cell death. Objectives -  To evaluate the effect of PDT on the in vitro growth of P. insidiosum and in an in vivo model of pythiosis. Methods -  For in vitro studies, two photosensitizers were evaluated: a haematoporphyrin derivative (Photogem®) and a chlorine (Photodithazine®). AmphotericinB was also evaluated, and the control group was treated with sterile saline solution. All experiments (PDT, porphyrin, chlorine and light alone, amphotericinB and saline solution) were performed as five replicates. For in vivo studies, six rabbits were inoculated with 20,000 zoospores of P. insidiosum, and an area of 1cm3 was treated using the same sensitizers. The PDT irradiation was performed using a laser emitting at 660nm and a fluence of 200J/cm2. Rabbits were clinically evaluated daily and histopathological analysis was performed 72h after PDT. Results -  For in vitro assays, inhibition rates for PDT ranged from 60 to 100% and showed better results in comparison to amphotericinB. For the in vivo assays, after PDT, histological analysis of lesions showed a lack of infection up to 1cm in depth. Conclusions and clinical importance -  In vitro and in vivo studies showed that PDT was effective in the inactivation of P. insidiosum and may represent a new approach to treating pythiosis. © 2013 The Authors. Veterinary Dermatology © 2013 ESVD and ACVD.

Biomimetic sensor based on 5,10,15,20-tetrakis(pentafluorophenyl)-21H,23H- porphyrin iron (III) chloride and MWCNT for selective detection of 2,4-D

Exploitation of the electronic properties of carbon nanotubes for the development of voltammetric and amperometric sensors to monitor analytes of environmental relevance has increased in recent years. This work reports the development of a biomimetic sensor based on a carbon paste modified with 5,10,15,20-tetrakis(pentafluorophenyl)-21H,23H-porphyrin iron (III) chloride (a biomimetic catalyst of the P450 enzyme) and multi-wall carbon nanotubes (MWCNT), for the sensitive and selective detection of the herbicide 2,4- dichlorophenoxyacetic acid (2,4-D). The sensor was evaluated using cyclic voltammetry and amperometry, for electrochemical characterization and quantification purposes, respectively. Amperometric analyses were carried out at -100 mV vs. Ag/AgCl(KClsat), using a 0.1 mol L-1 phosphate buffer solution at pH 6.0 as the support electrolyte. Under these optimized analytical conditions, the sensor showed a linear response between 9.9 × 10-6 and 1.4 × 10-4 mol L-1, a sensitivity of 1.8 × 104 (±429) μA L mol -1, and limits of detection and quantification of 2.1 × 10 -6 and 6.8 × 10-6 mol L-1, respectively. The incorporation of functionalized MWCNT in the carbon paste resulted in a 10-fold increase in the response, compared to that of the biomimetic sensor without MWCNT. In addition, the low applied potential (-100 mV) used to obtain high sensitivity also contributed to the excellent selectivity of the proposed sensor. The viability of the application of this sensor for analysis of soil samples was confirmed by satisfactory recovery values, with a mean of 96% and RSD of 2.1% (n = 3). © 2013 Elsevier B.V.

Dystrophic Epidermolysis Bullosa in Goats

Clinical, histopathological and ultrastructural findings of caprine dystrophic epidermolysis bullosa (DEB) with autosomal recessive inheritance are reported. The goats presented with exungulation, erosions, crusts and scars on the skin and ulcers in the oral cavity. Microscopically, the skin showed subepidermal separation with clefts filled occasionally with clear eosinophilic fluid, cellular debris or neutrophils. Ultrastructurally, the site of blister formation was the sublamina densa in the epidermal basement membrane zone. In skin with blister formation and in clinically uninvolved skin, the basal lamina was preserved, but the anchoring fibrils were sparse and rudimentary. A twin brother of an affected kid was mated over 5 years with his mother; three out of the 10 kids born presented with epidermolysis bullosa, indicating that the disease has an autosomal recessive mode of inheritance. It is suggested that the disease is similar to human severe generalized recessive DEB. © 2012 Elsevier Ltd.