958 resultados para Reactor of the fixed bed
Resumo:
OBJECTIVES: To determine the prevalence of Her-2/Neu-cerbb-2 in the gastric mucosa of patients with gastric adenocarcinoma in a brazilian patient group. METHODS: The immunohistochemical expression of Her-2/Neu was studied in 37 formalin-fixed paraffin-embedded tissue sections. RESULTS: The immunohistochemical reaction produced by the anti-HER-2/Neu antibody was positive in two cases (5.4%). CONCLUSION: The low prevalence of Her-2/Neu observed in these southern brazilian cases is probably due to the great number of poorly differentiated cancers in this serie.
Resumo:
The objectives were to determine the prevalence of fibrinonecrotic enteritis (FNE) on a farrow-to-finish farm of 1,000 sows, to categorize the pathological changes, and to to investigate the lesion associated agents Isospora suis and Clostridium perfringens. Causes of preweaning mortality (PWM) were classified into 8 categories including FNE. Obtained data were evaluated for statistical significance by adjusted Chi-square analysis. Samples of FNE were taken for complementary studies including a PCR technique for genotyping toxin genes of Clostridium perfringens from gut samples fixed in 10% neutral formalin. From 3,153 piglets examined, less than 1% was classified as FNE. FNE prevalence increased progressively from the first to the third week, the last differing statistically from the others. Eighty percent of gut samples with FNE lesions were positive to Isospora suis, when examined by PCR from 9 severe FNE lesions detected 7 positive samples only for a toxin gene, characteristic of C. perfringens type-A.
Resumo:
The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.
Resumo:
Thirty heads with the neck segment of Caiman latirostris were used. The animals were provided from a creation center called Mister Caiman, under the authorization of the Brazilian Institute of Environment and Renewable Natural Resources (Ibama). Animals were sacrificed according to the slaughtering routine of the abattoir, and the heads were sectioned at the level of the third cervical vertebra. The arterial system was washed with cold saline solution, with drainage through jugular veins. Subsequently, the system was filled with red colored latex injection. Pieces were than fixed in 20% formaldehyde, for seven days. The brains were removed, with a spinal cord segment, the duramater removed and the arteries dissected. At the level of the hypophysis, the internal carotid artery gave off a rostral branch, and a short caudal branch, continuing, naturally, as the caudal cerebral artery. This artery projected laterodorsalwards and, as it overpassed the optic tract, gave off its I (the first) central branch. Penetrated in the cerebral transverse fissure, emitting the diencephalic artery and next its II (second) central branch. Still inside the fissure, originated occipital hemispheric branches and a pineal branch. Emerged from the cerebral transverse fissure, over the occipital pole of the cerebral hemisphere. Projected rostralwards, sagital to the cerebral longitudinal fissure, as interhemispheric artery. This artery gave off medial and convex hemispheric branches to the respective surfaces of the cerebral hemispheres, anastomosed with its contralateral homologous, forming the common ethmoidal artery. This artery entered the fissure between the olfactory peduncles, emerging ventrally and dividing into ethmoidal arteries, right and left, which progressed towards the nasal cavities, vascularizing them. The territory of the caudal cerebral artery included the most caudal area of the base of the cerebral hemisphere, its convex surface, the olfactory peduncles and bulbs, the choroid plexuses and the diencephalus with its parietal organs.
Resumo:
Male capacity for spreading genes to a great number of descendents and to determine population dynamics depend directly on the genital organs. Morphological studies in pinnipeds are scarce and the functional meaning of some characteristics has never been discussed. We hypothesized that Arctocephalus australis (A. australis) shows morphophysiological adaptations in order to guarantee the perpetuation of the species in the unique annual mating season. Seven males, dead from natural causes, had their genital organs collected and fixed for morphological description. Some features differ from other described mammalian males and are closely related to the biology and reproductive cycle of this species, as the scrotal epidermis, absence of glandular portion in the ductus deferens and spermatogenic epithelium suggest a recrudescent testis period. The corona glandis exhibits a singular arrangement: its erectile border looks like a formation of petals and its association with the os penis gives a "lily-flower" form to this region. We propose the name margo petaliformis to this particular erectile border of the corona glandis because of its similarity to a flower corola. The male genital organs of A. australis show morphological features compatible with adaptation to environment requirements and reproductive efficiency.
Resumo:
Thirty Meleagris gallopavo heads with their neck segments were used. Animals were contained and euthanized with the association of mebezonium iodide, embutramide and tetracaine hydrochloride (T 61, Intervet ) by intravenous injection. The arterial system was rinsed with cold saline solution (15°C), with 5000IU heparin and filled with red-colored latex. The samples were fixed in 20% formaldehyde for seven days. The brains were removed with a segment of cervical spinal cord and after, the dura-mater was removed and the arteries dissected. The cerebral carotid arteries, after the intercarotid anastomosis, were projected around the hypophysis, until they reached the tuber cinereum and divided into their terminal branches, the caudal branch and the rostral branch. The rostral branch was projected rostrolateralwards and gave off, in sequence, two collateral branches, the caudal cerebral and the middle cerebral arteries and the terminal branch was as cerebroethmoidal artery. The caudal cerebral artery of one antimere formed the interhemispheric artery, which gave off dorsal hemispheric branches to the convex surface of both antimeres. Its dorsal tectal mesencephalic branch, of only one antimere, originated the dorsal cerebellar artery. In the interior of the cerebral transverse fissure, after the origin of the dorsal tectal mesencephalic artery, the caudal cerebral artery emitted occipital hemispheric branches, pineal branches and medial hemispheric branches, on both antimeres. The caudal cerebral artery's territory comprehended the entire surface of the dorsal hemioptic lobe, the rostral surface of the cerebellum, the diencephalic structures, the caudal pole and the medial surface of the cerebral hemisphere and in the convex surface, the sagittal eminence except for its most rostral third. Due to the asymmetry found in the caudal cerebral arteries' ramifications, the models were classified into three types and their respective subtypes.
Resumo:
This thesis presents a one-dimensional, semi-empirical dynamic model for the simulation and analysis of a calcium looping process for post-combustion CO2 capture. Reduction of greenhouse emissions from fossil fuel power production requires rapid actions including the development of efficient carbon capture and sequestration technologies. The development of new carbon capture technologies can be expedited by using modelling tools. Techno-economical evaluation of new capture processes can be done quickly and cost-effectively with computational models before building expensive pilot plants. Post-combustion calcium looping is a developing carbon capture process which utilizes fluidized bed technology with lime as a sorbent. The main objective of this work was to analyse the technological feasibility of the calcium looping process at different scales with a computational model. A one-dimensional dynamic model was applied to the calcium looping process, simulating the behaviour of the interconnected circulating fluidized bed reactors. The model incorporates fundamental mass and energy balance solvers to semi-empirical models describing solid behaviour in a circulating fluidized bed and chemical reactions occurring in the calcium loop. In addition, fluidized bed combustion, heat transfer and core-wall layer effects were modelled. The calcium looping model framework was successfully applied to a 30 kWth laboratory scale and a pilot scale unit 1.7 MWth and used to design a conceptual 250 MWth industrial scale unit. Valuable information was gathered from the behaviour of a small scale laboratory device. In addition, the interconnected behaviour of pilot plant reactors and the effect of solid fluidization on the thermal and carbon dioxide balances of the system were analysed. The scale-up study provided practical information on the thermal design of an industrial sized unit, selection of particle size and operability in different load scenarios.
Resumo:
The work is mainly focused on the technology of bubbling fluidized bed combustion. Heat transfer and hydrodynamics of the process were examined in the work in detail. Special emphasis was placed on the process of heat exchange in a freeboard zone of bubbling fluidized bed boiler. Operating mode of bubbling fluidized bed boiler depends on many parameters. To assess the influence of some parameters on a temperature regime inside the furnace a simplified method of zonal modeling was used in the work. Thus, effects of bed material fineness, excess air ratio and changes in boiler load were studied. Besides the technology of combustion in bubbling fluidized bed, other common technologies of solid fuels combustion were reviewed. In addition, brief survey of most widely used types of solid fuel was performed in the work.
Resumo:
In Lamium album, sucrose and raffinose-family oligosaccharides are the major products of photosynthesis that are stored in leaves. Using gas analysis and 14CO2 feeding, we compared photosynthesis and the partitioning of recently-fixed carbon in plants where sink activity was lowered by excision of flowers and chilling of roots with those where sink activity was not modified. Reduction in sink activity led to a reduction in the maximum rate of photosynthesis, to retention of fixed carbon in source leaves and to the progressive accumulation of raffinose-family oligosaccharides. This ultimately affected the extractable activities of invertase and sucrose phosphate synthase. At the end of the light period, invertase activity was significantly higher in treated plants. By contrast sucrose phosphate synthase activity was significantly lower in treated plants. We propose that reducing sink activity in L. album is associated with a shift in metabolism away from starch and sucrose synthesis and towards sucrose catabolism, galactinol utilisation and the synthesis of raffinose-family oligosaccharides.
Resumo:
Miconia albicans fruit and seed coat ontogeny were described under light microscope. The samples were fixed in formalin-aceto-alcohol (FAA), neutral-buffered formaldehyde solution (NBF) and formalin-ferrous sulphate (FFS) solutions, embedded in plastic resin, sectioned at 10 µm and stained with Toluidine Blue. Specific dyes and/or reagents were used for the microchemical tests. The ovary is semi-inferior and the indehiscent, fleshy globose berries are originated mainly from the development of the inferior portion of the ovary. The immature pericarp is mainly parenchymatous with some sclereids, druse crystal and phenolic-like compounds idioblasts widespread in the mesocarp. In the mature pericarp, the endocarp cells are often collapsed, the mesocarp is thick with cells more or less turgid, and the sclereids, the druses and the phenolic-like compound idioblasts are almost absent. The ovules are anatropous, bitegmic and crassinucellate, and the zig-zag micropyle is formed by both the exostome and the endostome. The mature seed is pyramidal-elongated in shape, exalbuminous and testal. The raphal part occupies about 40% of the seed coat total length and had the mechanical layer derived from its inner layer. The antiraphal side is non-multiplicative and the exotesta, mesotesta and endotesta are differentiated into a sclerotic layer, with the exotesta being the mechanical one. The tegmen is absent.
Resumo:
The crude latex of Crown-of-Thorns (Euphorbia milii var. hislopii) is a potent plant molluscicide and a promising alternative to the synthetic molluscicides used in schistosomiasis control. The present study was undertaken to investigate the embryofeto-toxic potential of E. milii latex. The study is part of a comprehensive safety evaluation of this plant molluscicide. Lyophilized latex (0, 125, 250 and 500 mg/kg body weight) in corn oil was given by gavage to Wistar rats (N = 100) from days 6 to 15 of pregnancy and cesarean sections were performed on day 21 of pregnancy. The numbers of implantation sites, living and dead fetuses, resorptions and corpora lutea were recorded. Fetuses were weighed, examined for external malformations, and fixed for visceral examination, or cleared and stained with Alizarin red S for skeleton evaluation. A reduction of body weight minus uterine weight at term indicated that E. milii latex was maternally toxic over the dose range tested. No latex-induced embryolethality was noted at the lowest dose (125 mg/kg) but the resorption rate was markedly increased at 250 mg/kg (62.5%) and 500 mg/kg (93.4%). A higher frequency of fetuses showing signs of delayed ossification (control: 17.4%; 125 mg/kg: 27.4% and 250 mg/kg: 62.8%; P<0.05 vs control) indicated that fetal growth was retarded at doses ³ 125 mg latex/kg body weight. No increase in the proportion of fetuses with skeletal anomalies was observed at the lowest dose but the incidence of minor skeletal malformations was higher at 250 mg/kg body weight (control: 13.7%; 125 mg/kg: 14.8%; 250 mg/kg: 45.7%; P<0.05 vs control). Since a higher frequency of minor malformations was noted only at very high doses of latex which are embryolethal and maternally toxic, it is reasonable to conclude that this plant molluscicide poses no teratogenic hazard or, at least, that this possibility is of a considerably low order of magnitude
Resumo:
The carotid bodies from adult spontaneous insulin-dependent diabetic rats (strain BB/S) were perfusion-fixed at normal arterial blood pressure with 3% phosphate-buffered glutaraldehyde and compared with the organs from control rats (strain BB/Sc) prepared in the same way. Serial 5-µm sections were cut, stained, and using an interactive image analysis system, were analysed to determine the volumes of the carotid body and its vascular and extravascular compartments. There was no evidence of systemic arterial disease in the carotid stem arteries in either group of animals, and the microvasculature of the organs appeared normal by light microscopy. The volume of the carotid body was unchanged 3 months after the onset of diabetes but was increased at 6 months. The total vascular volume of the organ was unchanged, but the volume of the small vessels (5-12 µm) was increased. In the control group the small vessels comprised 5% of the total volume of the carotid body, or about 44% of the vascular compartment. The percentage of small vessels increased at 3 months in the diabetic group, but had returned to normal at 6 months. The extravascular volume followed the same pattern as the total carotid body volume and so did not change appreciably when expressed as a percentage of the total volume of the organ. The increase in size of the carotid body in diabetic rats is due, therefore, to an augmented extravascular volume. In one diabetic specimen the carotid sinus nerve showed signs of diabetic neuropathy, axonal swelling and intramyelinic oedema. The clinical implications of these results are discussed.
Resumo:
Gasification of biomass is an efficient method process to produce liquid fuels, heat and electricity. It is interesting especially for the Nordic countries, where raw material for the processes is readily available. The thermal reactions of light hydrocarbons are a major challenge for industrial applications. At elevated temperatures, light hydrocarbons react spontaneously to form higher molecular weight compounds. In this thesis, this phenomenon was studied by literature survey, experimental work and modeling effort. The literature survey revealed that the change in tar composition is likely caused by the kinetic entropy. The role of the surface material is deemed to be an important factor in the reactivity of the system. The experimental results were in accordance with previous publications on the subject. The novelty of the experimental work lies in the used time interval for measurements combined with an industrially relevant temperature interval. The aspects which are covered in the modeling include screening of possible numerical approaches, testing of optimization methods and kinetic modelling. No significant numerical issues were observed, so the used calculation routines are adequate for the task. Evolutionary algorithms gave a better performance combined with better fit than the conventional iterative methods such as Simplex and Levenberg-Marquardt methods. Three models were fitted on experimental data. The LLNL model was used as a reference model to which two other models were compared. A compact model which included all the observed species was developed. The parameter estimation performed on that model gave slightly impaired fit to experimental data than LLNL model, but the difference was barely significant. The third tested model concentrated on the decomposition of hydrocarbons and included a theoretical description of the formation of carbon layer on the reactor walls. The fit to experimental data was extremely good. Based on the simulation results and literature findings, it is likely that the surface coverage of carbonaceous deposits is a major factor in thermal reactions.
Resumo:
In addition to the mutations that underlie most cases of the multiple endocrine neoplasia type 1 (MEN1) syndrome, somatic mutations of the MEN1 gene have also been described in sporadic tumors like gastrinomas, insulinomas and bronchial carcinoid neoplasm. We examined exon 2 of this gene, where most of the mutations have been described, in 148 endocrine and nonendocrine sporadic tumors. DNA was obtained by phenol/chloroform extraction and ethanol precipitation from 92 formalin-fixed, paraffin-embedded samples, and from 40 fresh tumor tissue samples. We used 5 pairs of primers to encompass the complete coding sequence of exon 2 of the MEN1 gene that was screened by the polymerase chain reaction-single-stranded conformation polymorphism (PCR-SSCP) technique in 78 sporadic thyroid cancers: 28 follicular adenomas, 35 papillary carcinomas, 14 follicular carcinomas, and 1 anaplastic thyroid carcinoma. We also examined 46 adrenal lesions (3 hyperplasias, 3 adenomas and 35 adrenocortical carcinomas, 2 pheochromocytomas, 2 ganglioneuroblastomas, and 1 lymphoma) and 24 breast cancers (6 noninvasive, 16 infiltrating ductal, and 2 invasive lobular tumors). The PCR product of 5 tumors suspected to present band shifts by SSCP was cloned. Direct sense and antisense sequencing did not identify mutations. These results suggest that the MEN1 gene is not important in breast, thyroid or adrenal sporadic tumorigenesis. Because the frequency of mutations varies significantly among tumor subgroups and allelic deletions are frequently observed at 11q13 in thyroid and adrenal cancers, another tumor suppressor gene residing in this region is likely to be involved in the tumorigenesis of these neoplasms.
Resumo:
If a dot is flashed in perfect alignment with a pair of dots rotating around the visual fixation point, most observers perceive the rotating dots as being ahead of the flashing dot (flash-lag effect). This perceptual effect has been interpreted to result from the perceptual extrapolation of the moving dots, the differential visual latencies between flashing and moving stimuli, as well as the modulation of attentional mechanisms. Here we attempted to uncouple the attentional effects brought about by the spatial predictability of the flashing dot from the sensory effects dependent on its visual eccentricity. The stimulus was a pair of dots rotating clockwise around the fixation point. Another dot was flashed at either the upper right or the lower left of the visual field according to three separate blocked situations: fixed, alternate and random positions. Twenty-four participants had to judge, in all three situations, the location of the rotating dots in relation to the imaginary line connecting the flashing dot and the fixation point at the moment the dot was flashed. The flash-lag effect was observed in all three situations, and a clear influence of the spatial predictability of the flashing dot on the magnitude of the perceptual phenomenon was revealed, independently of sensory effects related to the eccentricity of the stimulus in the visual field. These findings are consistent with our proposal that, in addition to sensory factors, the attentional set modulates the magnitude of the differential latencies that give rise to the flash-lag phenomenon.