树木年轮硝化纤维素氢同位素组成的测定

树轮硝化纤维素氢同位素分析技术早已为国外学者所掌握，而分析技术上存在的难题使该项工作在国内进展缓慢，这在某种程度上限制了中国学者应用树轮氢同位素技术对过去全球变化的深入研究。在总结和分析前人工作的基础上，就树轮氢同位素的分析方法及初步应用开展了研究。 实验采用经典的金属锌单个还原法测定了水的氢同位素组成、采用熔封管高温燃烧法和金属锌还原法测定了有机质和树轮硝化纤维素的氢同位素组成。通过对实验结果进行分析，最后得出如下结论： 第一，要获得可靠的氢同位素比值，必须保持固定的硝化纤维素/锌质量比，即按照产生2μL（约112μmole）水的硝化纤维素与每100mg的锌与的比例装样。实验中根据1和0.7两种水/锌的比例对CH7样品装样，发现后面那一组得出的实验值（-95.6‰）比给定值（-100.3±2‰）大，而前面那一组的实验值（-100.2‰）跟IAEA的给定值一致。 第二，在真空系统上必须对硝化纤维素进行足够长时间的加热，如在80℃下加热1小时左右，以最大限度移去硝化纤维素吸附的水分。9月9日分析树轮硝化纤维素样品DN-27时，加热时间是45分钟，得到的分析精度是2.2‰；9月13日对树轮硝化纤维素样品LN-31的分析精度提高达到了1.6‰，主要是因为加热时间由原来的45分钟延长到75分钟。 第三，铜粒的加入不会改进硝化纤维素氢同位素分析的精度。通过实验对照，除了加铜粒与否，其他实验条件如样品量，水/锌的比值，加热条件等均相同，样品CH7-5和 -3 (8月31日), 样品CH7-16 和18 (9月8日)以及样品CN-1 和CN-2 (8月31日)的结果表明加入和没有加入铜的样品之间没有显著差异。 第四，硝化纤维素或有机质燃烧后，应尽快将其中的水分在高真空线上萃取出来转移到装有锌粒的反应管中，以避免生成的水分、二氧化碳和氧化铜的进一步反应。硝化纤维素样品CN-3的氢同位素组成测定结果比其他两个CN样品（CN-1和CN-2）得到的结果高了14‰，主要是因为水分提取的时间比其他样品延长了2天。 实验测定树轮硝化纤维素样品DN-27氢同位素组成的精度达到2.2‰，测定树轮硝化纤维素样品LN-31氢同位素组成的精度达到1.6‰,这与国际认可的2.0‰的精度大体相同，从而摸索出了石英管高温燃烧法配合金属锌还原法分析有机质氢同位素组成的实验条件和氢同位素数据的校正方法。为从我国的树轮、泥炭、湖泊沉积和古土壤中提取东亚季风高分辨率变化信息奠定技术基础，也为我国植物生理学家利用氢同位素技术示踪植物生理过程提供了较好的技术平台。

Podridoes-moles das hortalicas causadas por bacterias.

Agentes causadores; Sensibilidade das hortalicas; Condicoes ambientais favoraveis; Exemplos de podridoes-moles em hortalicas; Controle.

Isospecific polymerization of styrene with modified ziegler-type catalysts

Effects of various kinds of additives as well as aging of the catalyst on the polymerization of styrene catalyzed by TiCl4/MgCl2-AlEt3 system have been studied. Experiments show that in toluene the isotacticity of polystyrene can be up to 83% for aged catalyst, whereas when the catalyst is not aged. non-stereospecific polymer is the main product. When PCl3 is used as an additive, the catalyst system gives high activity and isotacticity. The use of a mixture of AlEt3/H2O (1: 1 mole ratio) as a cocatalyst is also efficient. The catalyst [TiCl4-PCl3/MgCl2-AlEt3/H2O] displays high activity and product isotacticity (94%) with an average molecular weight up to 2 X 10(-6). When Co(acac)(3) is added to to [TiCl4/MgCl2-AlEt3] catalyst after it was aged, the isotacticity can be up to 97%. (C) 2001 Elsevier Science Ltd. All rights reserved.

Modification of a poly(methyl methacrylate) injection-molded microchip and its use for high performance analysis of DNA

Inexpensive and permanently modified poly(methyl methacrylate)(PMMA) microchips were fabricated by an injection-molding process. A novel sealing method for plastic microchips at room temperature was introduced. Run-to-run and chip-to-chip reproducibility was good, with relative standard deviation values between 1-3% for the run-to-run and less than 2.1% for the chip-to-chip comparisons. Acrylonitrile-butadiene-styrene (ABS) was used as an additive in PMMA substrates. The proportions of PMMA and ABS were optimized. ABS may be considered as a modifier, which obviously improved some characteristics of the microchip, such as the hydrophilicity and the electro-osmotic flow (EOF). The detection limit of Rhodamine 6G dye for the modified microchip on the home-made microchip analyzer showed a dramatic 100-fold improvement over that for the unmodified PMMA chip. A detection limit of the order of 10(-20) mole has been achieved for each injected phiX-174/HaeIII DNA fragment with the baseline separation between 271 and 281 bp, and fast separation of 11 DNA restriction fragments within 180 seconds. Analysis of a PCR product from the tobacco ACT gene was performed on the modified microchip as an application example.

Contribuição para o reconhecimento de doenças vasculares da bananeira (Musa spp).

Mal-do-panamá. Moko ou murcha bacteriana. Murcha de Erwinia ou podridão mole do rizoma. Murcha abiótica. Características diferenciadoras das murchas bióticas e abióticas em bananeiras. Sintomas externos. Sintomas internos.

Doenças da berinjela no Brasil.

2011

Textural and structural properties of bioactive glasses in the system CaO-SiO2

Gel-derived CaO-SiO2 binary glasses of CaO mole fractions 0. 2, 0.3 and 0. 4 have been prepared and characterised. Pore diameter specific pore volume, skeletal density and porosity were found to increase with increasing CaO-content, whereas a concomitant decrease in specific surface area was observed. Si-29 NMR indicated that the 0.2 CaO mole fraction glass consisted of higly polymerized Q(4) and Q(3) silicate species, with some Q(2) units. With increasing CaO mole fraction, these silicate species became progressively depolymerised such that isolated SiO4 tetrahedra were detected within the 0.4 CaO glass matrix. Unusually, the glasses retained a proportion of Q(4) and Q(3) species as the CaO mole fraction was increased. All glass formulations exhibited in vitro bioactivity. The rate of hydroxyapatite precipitation followed the order 0.2 CaO > 0.4 CaO > > 0.3 CaO, an effect that is attributed to differences in the rate of dissolution of calcium from these glasses. This, in turn, appears to be dependent upon the proportion of Ca 21 participating in the formation of the glassy network.

Oxygen photolysis in the Mauritanian upwelling: Implications for net community production

We carried out 16 photochemical experiments of filtered surface water in a custom-built solar simulator and concomitant measurements of in vitro gross primary production (GPP) and respiration (R) in the Mauritanian upwelling during a Lagrangian study following three sulfur hexafluoride–labeled patches of upwelled water (P1 to P3). Oxygen photolysis rates were correlated with the absorbance of chromophoric dissolved organic matter (CDOM) at 300 nm, suggesting first-order kinetics with respect to CDOM. An exponential fit was used to calculate the apparent quantum yield (AQY) for oxygen photolysis, giving an average AQY of 0.00053 µmol O2 (mole photons m−2 s−1)−1 at 280 nm and slope of 0.0012 nm−1. Modeled photochemical oxygen demand (POD) at the surface (3–16 mmol m−3 d−1) occasionally exceeded R and was dominated by ultraviolet radiation (71–79%). Euphotic-layer integrated GPP decreased with time during both P-1 and P-3, whereas R remained relatively constant and POD increased during P-1 and decreased during P-3. On Day 4 of P-3, GPP and POD maxima coincided with high CDOM absorbance, suggesting “new” CDOM production. Omitting POD may lead to an underestimation of net community production (NCP), both through in vitro and geochemical methods (here by 2–22%). We propose that oxygen-based NCP estimates should be revised upward. For the Mauritanian upwelling, the POD-corrected NCP was strongly correlated with standard NCP with a slope of 1.0066 ± 0.0244 and intercept of 46.51 ± 13.15 mmol m−2 d−1.

Energetics reveals physiologically distinct castes in a eusocial mammal.

Eusociality, which occurs among mammals only in two species of African mole-rat, is characterized by division of labour between morphologically distinct 'castes'1. In Damaraland mole-rats (Cryptomys damarensis), colony labour is divided between 'infrequent worker' and 'frequent worker' castes2. Frequent workers are active year-round and together perform more than 95% of the total work of the colony, whereas infrequent workers typically perform less than 5% of the total work3. Anecdotal evidence suggests that infrequent workers may act as dispersers, with dispersal being limited to comparatively rare periods when the soil is softened by moisture4, 5. Here we show that infrequent workers and queens increase their daily energy expenditure after rainfall whereas frequent workers do not. Infrequent workers are also fatter than frequent workers. We suggest that infrequent workers constitute a physiologically distinct dispersing caste, the members of which, instead of contributing to the work of the colony and helping the queen to reproduce, build up their own body reserves in preparation for dispersal and reproduction when environmental conditions are suitable.

Ion Association in [bmim][PF6]/Naphthalene Mixtures: An Experimental and Computational Study

Mixtures of room temperature ionic liquids (IL) with neutral organic molecules provide a valuable testing ground to investigate the interplay of the ionic and molecular-dipolar state in dense Coulomb systems at near ambient conditions. In the present study, the viscosity eta and the ionic conductivity a of 1-n-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6])/naphthalene mixtures at T = 80 degrees C have been measured at 10 stoichiometries spanning the composition range from pure naphthalene to pure [bmim][PF6]. The viscosity grows nearly monotonically with increasing IL mole fraction (x), whereas the conductivity per ion displays a clear peak at x approximate to 15%. The origin of this maximum has been investigated using molecular dynamics simulations based on a classical force field. Snapshots of the simulated samples show that the conductivity maximum is due to the gradual transition in the IL component from an ionic state at high x to a dipolar fluid made of neutral ion pairs at low x. At concentrations x <0.20 the ion pairs condense into molecular-thin filaments bound by dipolar forces and extending in between nanometric droplets of IL. These results are confirmed and complemented by the computation of dynamic and transport properties in [bmim][PF6]/naphthalene mixtures at low IL concentration.

Mutual Solubilities of Water and the [Cnmim][Tf2N] Hydrophobic Ionic Liquids

Ionic liquids (ILs) have recently garnered increased attention because of their potential environmental benefits as "green" replacements over conventional volatile organic solvents. While ILs cannot significantly volatilize and contribute to air pollution, even the most hydrophobic ones present some miscibility with water posing environmental risks to the aquatic ecosystems. Thus, the knowledge of ILs toxicity and their water solubility must be assessed before an accurate judgment of their environmental benefits and prior to their industrial applications. In this work, the mutual solubilities for [C2-C8mim][Tf2N] (n-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide) and water between 288.15 and 318.15 K at atmospheric pressure were measured. Although these are among the most hydrophobic ionic liquids known, the solubility of water in these compounds is surprisingly large, ranging from 0.17 to 0.36 in mole fraction, while the solubility of these ILs in water is much lower ranging from 3.2 × 10-5 to 1.1 × 10-3 in mole fraction, in the temperature and pressure conditions studied. From the experimental data, the molar thermodynamic functions of solution and solvation such as Gibbs energy, enthalpy, and entropy at infinite dilution were estimated, showing that the solubility of these ILs in water is entropically driven. The predictive capability of COSMO-RS, a model based on unimolecular quantum chemistry calculations, was evaluated for the description of the binary systems investigated providing an acceptable agreement between the model predictions and the experimental data both with the temperature dependence and with the ILs structural variations.

Impairments of hippocampal synaptic plasticity induced by aggregated beta-amyloid (25-35) are dependent on stimulation-protocol and genetic background

The aggregation of beta-amyloid to plaques in the brain is one of the hallmarks of Alzheimer disease (AD). Numerous studies have tried to elucidate to what degree amyloid peptides play a role in the neurodegenerative developments seen in AD. While most studies report an effect of amyloid on neural activity and cognitive abilities of rodents, there have been many inconsistencies in the results. This study investigated to what degree the different genetic backgrounds affect the outcome of beta-amyloid fragment (25-35) on synaptic plasticity in vivo in the rat hippocampus. Two strains, Wistar and Lister hooded rats, were tested. In addition, the effects of a strong (600 stimuli) and a weak stimulation protocol (100 stimuli) on impairments of LTP were analysed. Furthermore, since the state of amyloid aggregation appears to play a role in the induction of toxic processes, it was tested by dual polarisation interferometry to what degree and at what speed beta-amyloid (25-35) can aggregate in vitro. It was found that 100 nmol beta-amyloid (25-35) injected icv did impair LTP in Wistar rats when using the weak but not the strong stimulation protocol (P <0.001). One-hundred nano mole of the reverse sequence amyloid (35-25) had no effect. LTP in Lister Hooded rats was not impaired by amyloid at any stimulation protocol. The aggregation studies showed that amyloid (25-35) aggregated within hours, while amyloid (35-25) did not. These results show that the genetic background and the stimulation protocol are important variables that greatly influence the experimental outcome. The fact that amyloid (25-35) aggregated quickly and showed neurophysiological effects, while amyloid (35-25) did not aggregate and did not show any effects indicates that the state of aggregation plays an important role in the physiological effects.

Formation of Strecker aldehydes and pyrazines in a fried potato model system

Sugars and amino acids were removed from potato slices by soaking in water and ethanol. They were then infused with various combinations of sugars (glucose and/or fructose) and amino acids (asparagine, glutamine, leucine, isoleucine, phenylalanine, and/or methionine) and fried. Volatile compounds were trapped onto Tenax prior to gas chromatography-mass spectrometry. Relative amounts of compounds (relative to the internal standard) and relative yields (per mole of amino acid infused into the slices) were determined. Amounts of 10 pyrazines, 4 Strecker aldehydes, and 4 other compounds were monitored. Relative amounts and relative yields of compounds varied according to the composition of the system. For the single amino acid-glucose systems, leucine gave the highest relative amount and relative yield of its Strecker aldehyde. Asparagine and phenylalanine gave the highest total relative amount and total relative Yield, respectively, of pyrazines. In the system containing all of the amino acids and glucose, the relative amount of 3-methylbutanal was higher, whereas the amounts of the other monitored Strecker aldehydes were lower. Most of the relative amounts of individual pyrazines were lower compared to the glucose-asparagine system, whereas the total relative yield of pyrazines was lower, compared to all of the single amino acid-glucose mixtures. Addition of fructose to the mixed amino acid-glucose model system generated Strecker aldehydes and pyrazines in ratios that were more similar to those of untreated potato chips than to those from the same system but without fructose. Both the sugars and the amino acids present in potato are crucial to the development of flavor compounds in fried potato slices.