Effectiveness of Electrochemical Chloride Extraction for the Iowa Avenue Pedestrian Bridge, TR-499, 2005

The main objective of this study is to determine the effectiveness of the Electrochemical Chloride Extraction (ECE) technique on a bridge deck with very high concentrations of chloride. This ECE technique was used during the summer of 2003 to reverse the effects of corrosion, which had occurred in the reinforcing steel embedded in the pedestrian bridge deck over Highway 6, along Iowa Avenue, in Iowa City, Iowa, USA. First, the half cell potential was measured to determine the existing corrosion level in the field. The half-cell potential values were in the indecisive range of corrosion (between -200 mV and -350 mV). The ECE technique was then applied to remove the chloride from the bridge deck. The chloride content in the deck was significantly reduced from 25 lb/cy to 4.96 lb/cy in 8 weeks. Concrete cores obtained from the deck were measured for their compressive strengths and there was no reduction in strength due to the ECE technique. Laboratory tests were also performed to demonstrate the effectiveness of the ECE process. In order to simulate the corrosion in the bridge deck, two reinforced slabs and 12 reinforced beams were prepared. First, the half-cell potentials were measured from the test specimens and they all ranged below -200 mV. Upon introduction of 3% salt solution, the potential reached up to -500 mV. This potential was maintained while a salt solution was being added for six months. The ECE technique was then applied to the test specimens in order to remove the chloride from them. Half-cell potential was measured to determine if the ECE technique can effectively reduce the level of corrosion.

Transrectal specimen extraction after laparoscopic left colectomy: a case-matched study.

Aim  Avoiding 'mini-laparotomy' to extract a colectomy specimen may decrease wound complications and further improve recovery after laparoscopic surgery. The aim of this study was to develop a new technique for transrectal specimen extraction (TRSE) and to compare it with conventional laparoscopy (CL) for left sided colectomy. Method  Eleven patients with benign disease requiring either sigmoid or left colon resection underwent TRSE. The unfired circular stapler was inserted transanally and used as a guide to suture-close the recto-sigmoid junction laparoscopically and as a handle to pull the sutured sigmoid through the opened rectum inside a laparoscopic camera bag. The anvil was inserted into the lumen of the intussuscepted sigmoid and pushed to the level of the anastomosis. The anastomosis was fashioned end-to-end in the first patients and side-to-end in the following patients to improve safety. Intra-operative and postoperative outcomes of patients undergoing TRSE were compared with those of a group of 20 patients undergoing CL, who were matched for type of resection, body mass index and age. Results  The procedure was successful in all but the first patient who was converted to conventional laparoscopic colectomy without any additional morbidity. Two patients in the end-to-end anastomosis group, but none in the side-to-end group, developed peri-anastomotic sepsis. Compared with CL, patients undergoing TRSE did not show any significant differences in operative time, recovery or morbidity. Conclusion  Transrectal specimen extraction after left colectomy using the circular stapler technique is feasible. A side-to-end anastomosis appears safer than an end-to-end anastomosis. Further studies are needed to explore the potential advantages of this procedure over CL.

Construction mechanisms and thermal evolution of upper crustal intrusions : the Saint-Jean-du-Doigt bimodal intrusion (Brittany, France)

Understanding the emplacement and growth of intrusive bodies in terms of mechanism, duration, ther¬mal evolution and rates are fundamental aspects of crustal evolution. Recent studies show that many plutons grow in several Ma by in situ accretion of discrete magma pulses, which constitute small-scale magmatic reservoirs. The residence time of magmas, and hence their capacities to interact and differentiate, are con¬trolled by the local thermal environment. The latter is highly dependant on 1) the emplacement depth, 2) the magmas and country rock composition, 3) the country rock thermal conductivity, 4) the rate of magma injection and 5) the geometry of the intrusion. In shallow level plutons, where magmas solidify quickly, evi¬dence for magma mixing and/or differentiation processes is considered by many authors to be inherited from deeper levels. This work shows however that in-situ differentiation and magma interactions occurred within basaltic and felsic sills at shallow depth (0.3 GPa) in the St-Jean-du-Doigt (SJDD) bimodal intrusion, France. This intrusion emplaced ca. 347 Ma ago (IDTIMS U/Pb on zircon) in the Precambrian crust of the Armori- can massif and preserves remarkable sill-like emplacement processes of bimodal mafic-felsic magmas. Field evidence coupled to high precision zircon U-Pb dating document progressive thermal maturation within the incrementally built ioppolith. Early m-thick mafic sills (eastern part) form the roof of the intrusion and are homogeneous and fine-grained with planar contacts with neighboring felsic sills; within a minimal 0.8 Ma time span, the system gets warmer (western part). Sills are emplaced by under-accretion under the old east¬ern part, interact and mingle. A striking feature of this younger, warmer part is in-situ differentiation of the mafic sills in the top 40 cm of the layer, which suggests liquids survival in the shallow crust. Rheological and thermal models were performed in order to determine the parameters required to allow this observed in- situ differentiation-accumulation processes. Strong constraints such as total emplacement durations (ca. 0.8 Ma, TIMS date) and pluton thickness (1.5 Km, gravity model) allow a quantitative estimation of the various parameters required (injection rates, incubation time,...). The results show that in-situ differentiation may be achieved in less than 10 years at such shallow depth, provided that: (1) The differentiating sills are injected beneath consolidated, yet still warm basalt sills, which act as low conductive insulating screens (eastern part formation in the SJDD intrusion). The latter are emplaced in a very short time (800 years) at high injection rate (0.5 m/y) in order to create a "hot zone" in the shallow crust (incubation time). This implies that nearly 1/3 of the pluton (400m) is emplaced by a subsequent and sustained magmatic activity occurring on a short time scale at the very beginning of the system. (2) Once incubation time is achieved, the calculations show that a small hot zone is created at the base of the sill pile, where new injections stay above their solidus T°C and may interact and differentiate. Extraction of differentiated residual liquids might eventually take place and mix with newly injected magma as documented in active syn-emplacement shear-zones within the "warm" part of the pluton. (3) Finally, the model show that in order to maintain a permanent hot zone at shallow level, injection rate must be of 0.03 m/y with injection of 5m thick basaltic sills eveiy 130yr, imply¬ing formation of a 15 km thick pluton. As this thickness is in contradiction with the one calculated for SJDD (1.5 Km) and exceed much the average thickness observed for many shallow level plutons, I infer that there is no permanent hot zone (or magma chambers) at such shallow level. I rather propose formation of small, ephemeral (10-15yr) reservoirs, which represent only small portions of the final size of the pluton. Thermal calculations show that, in the case of SJDD, 5m thick basaltic sills emplaced every 1500 y, allow formation of such ephemeral reservoirs. The latter are formed by several sills, which are in a mushy state and may interact and differentiate during a short time.The mineralogical, chemical and isotopic data presented in this study suggest a signature intermediate be¬tween E-MORB- and arc-like for the SJDD mafic sills and feeder dykes. The mantle source involved produced hydrated magmas and may be astenosphere modified by "arc-type" components, probably related to a sub¬ducting slab. Combined fluid mobile/immobile trace elements and Sr-Nd isotopes suggest that such subduc¬tion components are mainly fluids derived from altered oceanic crust with minor effect from the subducted sediments. Close match between the SJDD compositions and BABB may point to a continental back-arc setting with little crustal contamination. If so, the SjDD intrusion is a major witness of an extensional tectonic regime during the Early-Carboniferous, linked to the subduction of the Rheno-Hercynian Ocean beneath the Variscan terranes. Also of interest is the unusual association of cogenetic (same isotopic compositions) K-feldspar A- type granite and albite-granite. A-type granites may form by magma mixing between the mafic magma and crustal melts. Alternatively, they might derive from the melting of a biotite-bearing quartz-feldspathic crustal protolith triggered by early mafic injections at low crustal levels. Albite-granite may form by plagioclase cu¬mulate remelting issued from A-type magma differentiation.

Comparison of naphthalene bioavailability determined by whole-cell biosensing and availability determined by extraction with Tenax

A rapid biological method for the determination of the bioavailability of naphthalene was developed and its value as an alternative to extraction-based chemical approaches demonstrated. Genetically engineered whole-cell biosensors are used to determine bioavailable naphthalene and their responses compared with results from Tenax extraction and chemical analysis. Results show a 1:1 correlation between biosensor results and chemical analyses for naphthalene-contaminated model materials and sediments, but the biosensor assay is much faster. This work demonstrates that biosensor technology can perform as well as standard chemical methods, though with some advantages including the inherent biological relevance of the response, rapid response time, and potential for field deployment. A survey of results from this work and the literature shows that bioavailability under non-equilibrium conditions nonetheless correlates well with K(oc) or K(d). A rationale is provided wherein chemical resistance is speculated to be operative.

Repurposing Social Tagging Data for Extraction of Domain-level Concepts

The World Wide Web, the world¿s largest resource for information, has evolved from organizing information using controlled, top-down taxonomies to a bottom up approach that emphasizes assigning meaning to data via mechanisms such as the Social Web (Web 2.0). Tagging adds meta-data, (weak semantics) to the content available on the web. This research investigates the potential for repurposing this layer of meta-data. We propose a multi-phase approach that exploits user-defined tags to identify and extract domain-level concepts. We operationalize this approach and assess its feasibility by application to a publicly available tag repository. The paper describes insights gained from implementing and applying the heuristics contained in the approach, as well as challenges and implications of repurposing tags for extraction of domain-level concepts.

Influence of rootstocks and pruning times on yield and on nutrient content and extraction in 'Niagara Rosada' grapevine

The objective of this work was to evaluate the influence of rootstocks and pruning times on yield and on nutrient content and extraction by pruned branches and harvested bunches of 'Niagara Rosada' grapevine in subtropical climate. The rootstocks 'IAC 766', 'IAC 572', 'IAC 313', 'IAC 571-6', and '106-8 Mgt' were evaluated. Treatments consisted of a combination between five rootstocks and three pruning times. At pruning, fresh and dry matter mass of branches were evaluated to estimate biomass accumulation. At harvest, yield was estimated by weighing of bunches per plant. Branches and bunches were sampled at pruning and at harvest, respectively, for nutrient content analysis. Nutrient content and dry matter mass of branches and bunches were used to estimate total nutrient extraction. 'Niagara Rosada' grapevine grafted onto the 'IAC 572' rootstock had the highest yield and dry matter mass of bunches, which were significantly different from the ones observed in 'Niagara Rosada'/'IAC 313'. 'Niagara Rosada' grafted onto the 'IAC 572' rootstock extracted the largest quantity of K, P, Mg, S, Cu, and Fe, differing from 'IAC 313' and 'IAC 766' in K and P extraction, and from '106-8 Mgt' in Mg and S extraction. Winter pruning results in higher yield, dry matter accumulation by branches, and total nutrient content and extraction.

Embedding, Extraction and Detection of Digital Watermark in Spectral Images

Tässä diplomityössä tutkitaan tekniikoita, joillavesileima lisätään spektrikuvaan, ja menetelmiä, joilla vesileimat tunnistetaanja havaitaan spektrikuvista. PCA (Principal Component Analysis) -algoritmia käyttäen alkuperäisten kuvien spektriulottuvuutta vähennettiin. Vesileiman lisääminen spektrikuvaan suoritettiin muunnosavaruudessa. Ehdotetun mallin mukaisesti muunnosavaruuden komponentti korvattiin vesileiman ja toisen muunnosavaruuden komponentin lineaarikombinaatiolla. Lisäyksessä käytettävää parametrijoukkoa tutkittiin. Vesileimattujen kuvien laatu mitattiin ja analysoitiin. Suositukset vesileiman lisäykseen esitettiin. Useita menetelmiä käytettiin vesileimojen tunnistamiseen ja tunnistamisen tulokset analysoitiin. Vesileimojen kyky sietää erilaisia hyökkäyksiä tarkistettiin. Diplomityössä suoritettiin joukko havaitsemis-kokeita ottamalla huomioon vesileiman lisäyksessä käytetyt parametrit. ICA (Independent Component Analysis) -menetelmää pidetään yhtenä mahdollisena vaihtoehtona vesileiman havaitsemisessa.

Supervised localimage feature detection

This thesis is about detection of local image features. The research topic belongs to the wider area of object detection, which is a machine vision and pattern recognition problem where an object must be detected (located) in an image. State-of-the-art object detection methods often divide the problem into separate interest point detection and local image description steps, but in this thesis a different technique is used, leading to higher quality image features which enable more precise localization. Instead of using interest point detection the landmark positions are marked manually. Therefore, the quality of the image features is not limited by the interest point detection phase and the learning of image features is simplified. The approach combines both interest point detection and local description into one phase for detection. Computational efficiency of the descriptor is therefore important, leaving out many of the commonly used descriptors as unsuitably heavy. Multiresolution Gabor features has been the main descriptor in this thesis and improving their efficiency is a significant part. Actual image features are formed from descriptors by using a classifierwhich can then recognize similar looking patches in new images. The main classifier is based on Gaussian mixture models. Classifiers are used in one-class classifier configuration where there are only positive training samples without explicit background class. The local image feature detection method has been tested with two freely available face detection databases and a proprietary license plate database. The localization performance was very good in these experiments. Other applications applying the same under-lying techniques are also presented, including object categorization and fault detection.

Enzymatic technology to improve oil extraction from Caryocar brasiliense camb. (Pequi) Pulp.

The present study aims to compare yield and quality of pequi pulp oil when applying two distinct processes: in the first, pulp drying in a tray dryer at 60ºC was combined with enzymatic treatment and pressing to oil extraction; in the second, a simple process was carried out by combining sun-drying pulp and pressing. In this study, raw pequi fruits were collected in Mato Grosso State, Brazil. The fruits were autoclaved at 121ºC and stored under refrigeration. An enzymatic extract with pectinase and CMCase activities was used for hydrolysis of pequi pulp, prior to oil extraction. The oil extractions were carried out by hydraulic pressing, with or without enzymatic incubation. The oil content in the pequi pulp (45% w/w) and the physicochemical characteristic of the oil was determined according to standard analytical methods. Free fatty acids, peroxide values, iodine and saponification indices were respectively 1.46 mgKOH/g, 2.98 meq/kg, 49.13 and 189.40. The acidity and peroxide values were lower than the obtained values in commercial oil samples, respectively 2.48 mgKOH/g and 5.22 meq/kg. Aqueous extraction has presented lower efficiency and higher oxidation of unsaturated fatty acids. On the other hand, pequi pulp pressing at room temperature has produced better quality oil. However its efficiency is still smaller than the combined enzymatic treatment and pressing process. This combined process promotes cellular wall hydrolysis and pulp viscosity reduction, contributing to at least 20% of oil yield increase by pressing.

Spontaneous Cdc42 polarization independent of GDI-mediated extraction and actin-based trafficking.

The small Rho-family GTPase Cdc42 is critical for cell polarization and polarizes spontaneously in absence of upstream spatial cues. Spontaneous polarization is thought to require dynamic Cdc42 recycling through Guanine nucleotide Dissociation Inhibitor (GDI)-mediated membrane extraction and vesicle trafficking. Here, we describe a functional fluorescent Cdc42 allele in fission yeast, which demonstrates Cdc42 dynamics and polarization independent of these pathways. Furthermore, an engineered Cdc42 allele targeted to the membrane independently of these recycling pathways by an amphipathic helix is viable and polarizes spontaneously to multiple sites in fission and budding yeasts. We show that Cdc42 is highly mobile at the membrane and accumulates at sites of activity, where it displays slower mobility. By contrast, a near-immobile transmembrane domain-containing Cdc42 allele supports viability and polarized activity, but does not accumulate at sites of activity. We propose that Cdc42 activation, enhanced by positive feedback, leads to its local accumulation by capture of fast-diffusing inactive molecules.

Exploring transparent approaches to the authentication of signatures on artwork

This thesis is composed of three main parts. The first consists of a state of the art of the different notions that are significant to understand the elements surrounding art authentication in general, and of signatures in particular, and that the author deemed them necessary to fully grasp the microcosm that makes up this particular market. Individuals with a solid knowledge of the art and expertise area, and that are particularly interested in the present study are advised to advance directly to the fourth Chapter. The expertise of the signature, it's reliability, and the factors impacting the expert's conclusions are brought forward. The final aim of the state of the art is to offer a general list of recommendations based on an exhaustive review of the current literature and given in light of all of the exposed issues. These guidelines are specifically formulated for the expertise of signatures on paintings, but can also be applied to wider themes in the area of signature examination. The second part of this thesis covers the experimental stages of the research. It consists of the method developed to authenticate painted signatures on works of art. This method is articulated around several main objectives: defining measurable features on painted signatures and defining their relevance in order to establish the separation capacities between groups of authentic and simulated signatures. For the first time, numerical analyses of painted signatures have been obtained and are used to attribute their authorship to given artists. An in-depth discussion of the developed method constitutes the third and final part of this study. It evaluates the opportunities and constraints when applied by signature and handwriting experts in forensic science. A brief summary covering each chapter allows a rapid overview of the study and summarizes the aims and main themes of each chapter. These outlines presented below summarize the aims and main themes addressed in each chapter. Part I - Theory Chapter 1 exposes legal aspects surrounding the authentication of works of art by art experts. The definition of what is legally authentic, the quality and types of the experts that can express an opinion concerning the authorship of a specific painting, and standard deontological rules are addressed. The practices applied in Switzerland will be specifically dealt with. Chapter 2 presents an overview of the different scientific analyses that can be carried out on paintings (from the canvas to the top coat). Scientific examinations of works of art have become more common, as more and more museums equip themselves with laboratories, thus an understanding of their role in the art authentication process is vital. The added value that a signature expertise can have in comparison to other scientific techniques is also addressed. Chapter 3 provides a historical overview of the signature on paintings throughout the ages, in order to offer the reader an understanding of the origin of the signature on works of art and its evolution through time. An explanation is given on the transitions that the signature went through from the 15th century on and how it progressively took on its widely known modern form. Both this chapter and chapter 2 are presented to show the reader the rich sources of information that can be provided to describe a painting, and how the signature is one of these sources. Chapter 4 focuses on the different hypotheses the FHE must keep in mind when examining a painted signature, since a number of scenarios can be encountered when dealing with signatures on works of art. The different forms of signatures, as well as the variables that may have an influence on the painted signatures, are also presented. Finally, the current state of knowledge of the examination procedure of signatures in forensic science in general, and in particular for painted signatures, is exposed. The state of the art of the assessment of the authorship of signatures on paintings is established and discussed in light of the theoretical facets mentioned previously. Chapter 5 considers key elements that can have an impact on the FHE during his or her2 examinations. This includes a discussion on elements such as the skill, confidence and competence of an expert, as well as the potential bias effects he might encounter. A better understanding of elements surrounding handwriting examinations, to, in turn, better communicate results and conclusions to an audience, is also undertaken. Chapter 6 reviews the judicial acceptance of signature analysis in Courts and closes the state of the art section of this thesis. This chapter brings forward the current issues pertaining to the appreciation of this expertise by the non- forensic community, and will discuss the increasing number of claims of the unscientific nature of signature authentication. The necessity to aim for more scientific, comprehensive and transparent authentication methods will be discussed. The theoretical part of this thesis is concluded by a series of general recommendations for forensic handwriting examiners in forensic science, specifically for the expertise of signatures on paintings. These recommendations stem from the exhaustive review of the literature and the issues exposed from this review and can also be applied to the traditional examination of signatures (on paper). Part II - Experimental part Chapter 7 describes and defines the sampling, extraction and analysis phases of the research. The sampling stage of artists' signatures and their respective simulations are presented, followed by the steps that were undertaken to extract and determine sets of characteristics, specific to each artist, that describe their signatures. The method is based on a study of five artists and a group of individuals acting as forgers for the sake of this study. Finally, the analysis procedure of these characteristics to assess of the strength of evidence, and based on a Bayesian reasoning process, is presented. Chapter 8 outlines the results concerning both the artist and simulation corpuses after their optical observation, followed by the results of the analysis phase of the research. The feature selection process and the likelihood ratio evaluation are the main themes that are addressed. The discrimination power between both corpuses is illustrated through multivariate analysis. Part III - Discussion Chapter 9 discusses the materials, the methods, and the obtained results of the research. The opportunities, but also constraints and limits, of the developed method are exposed. Future works that can be carried out subsequent to the results of the study are also presented. Chapter 10, the last chapter of this thesis, proposes a strategy to incorporate the model developed in the last chapters into the traditional signature expertise procedures. Thus, the strength of this expertise is discussed in conjunction with the traditional conclusions reached by forensic handwriting examiners in forensic science. Finally, this chapter summarizes and advocates a list of formal recommendations for good practices for handwriting examiners. In conclusion, the research highlights the interdisciplinary aspect of signature examination of signatures on paintings. The current state of knowledge of the judicial quality of art experts, along with the scientific and historical analysis of paintings and signatures, are overviewed to give the reader a feel of the different factors that have an impact on this particular subject. The temperamental acceptance of forensic signature analysis in court, also presented in the state of the art, explicitly demonstrates the necessity of a better recognition of signature expertise by courts of law. This general acceptance, however, can only be achieved by producing high quality results through a well-defined examination process. This research offers an original approach to attribute a painted signature to a certain artist: for the first time, a probabilistic model used to measure the discriminative potential between authentic and simulated painted signatures is studied. The opportunities and limits that lie within this method of scientifically establishing the authorship of signatures on works of art are thus presented. In addition, the second key contribution of this work proposes a procedure to combine the developed method into that used traditionally signature experts in forensic science. Such an implementation into the holistic traditional signature examination casework is a large step providing the forensic, judicial and art communities with a solid-based reasoning framework for the examination of signatures on paintings. The framework and preliminary results associated with this research have been published (Montani, 2009a) and presented at international forensic science conferences (Montani, 2009b; Montani, 2012).

Modelling additional costs caused by a new product feature

Työn tavoitteena oli mallintaa uuden tuoteominaisuuden aiheuttamat lisäkustannukset ja suunnitella päätöksenteon työkalu Timberjack Oy:n kuormatraktorivalmistuksen johtoryhmälle. Tarkoituksena oli luoda karkean tason malli, joka sopisi eri tyyppisten tuoteominaisuuksien kustannuksien selvittämiseen. Uuden tuoteominaisuuden vaikutusta yrityksen eri toimintoihin selvitettiin haastatteluin. Haastattelukierroksen tukena käytettiin kysymyslomaketta. Haastattelujen tavoitteena oli selvittää prosessit, toiminnot ja resurssit, jotka ovat välttämättömiä uuden tuoteominaisuuden tuotantoon saattamisessa ja tuotannossa. Malli suunniteltiin haastattelujen ja tietojärjestelmästä hankitun tiedon pohjalta. Mallin rungon muodostivat ne prosessit ja toiminnot, joihin uudella tuoteominaisuudella on vaikutusta. Huomioon otettiin sellaiset resurssit, joita uusi tuoteominaisuus kuluttaa joko välittömästi, tai välillisesti. Tarkasteluun sisällytettiin ainoastaan lisäkustannukset. Uuden tuoteominaisuuden toteuttamisesta riippumattomat, joka tapauksessa toteutuvat yleiskustannukset jätettiin huomioimatta. Malli on yleistys uuden tuoteominaisuuden aiheuttamista lisäkustannuksista, koska tarkoituksena on, että se sopii eri tyyppisten tuoteominaisuuksien aiheuttamien kustannusten selvittämiseen. Lisäksi malli soveltuu muiden pienehköjen tuotemuutosten kustannusten kartoittamiseen.

Evaluation of the indication for surgical extraction of third molars according to the oral surgeon and the primary care dentist. Experience in the Master of Oral Surgery and Implantology at Barcelona University Dental School

Introduction: Third molar extraction is the most frequent procedure in oral surgery. The present study evaluates the indication of third molar extraction as established by the primary care dentist (PCD) and the oral surgeon, and compares the justification for extraction with the principal reason for patient consultation. Patients and method: A descriptive study was made of 319 patients subjected to surgical removal of a third molar in the context of the Master of Oral Surgery and Implantology (Barcelona University Dental School, Barcelona, Spain) between July 2004 and March 2005. The following parameters were evaluated: sex, age, molar, type of impaction, position according to the classifications of Pell and Gregory and of Winter, and the reasons justifying extraction. Results: The lower third molars were the most commonly extracted molars (73.7%). A total of 69.6% of the teeth were covered by soft tissues only. Fifty-six percent of the lower molars corresponded to Pell and Gregory Class IIB, while 42.1% were in the vertical position. The most common reason for patient reference to our Service of Oral Surgery on the part of the PCD was prophylactic removal (51.0% versus 46.1% in the case of the oral surgeon). Discussion and conclusions. Our results show prophylaxis to be the principal indication of third molar extraction, followed by orthodontic reasons. Regarding third molars with associated clinical symptoms or signs, infectious disease-including pericoronitis- was the pathology most often observed by the oral surgeon, followed by caries. This order of frequency was seen to invert in the case of third molars referred for extraction by the PCD. A vertical position predominated among the third molars with associated pathology