Microstructures and tensile properties of Mg-8Gd-0.6Zr-xNd-yY (x+y=3, mass%) alloys

Mg-8Gd-0.6Zr-xNd-yY (mass%) alloys which containing different Nd:Y mass ratio of 3:0, 2:1, 1:2 and 0:3 with a constant x + y = 3 were prepared by metal mould casting method, and the microstructure, aging behaviour and tensile properties have been investigated. The fibrous eutectic areas along the boundaries enlarge clearly in the as-cast alloys containing Y element, and the fine grain boundaries and dispersed precipitation are observed in the aged alloys. The Mg-8Gd-0.6Zr-2Nd-Y alloy exhibits notably age-hardening behaviour and the highest mechanical property. The ultimate tensile strength and yield strength of Mg-8Gd-0.6Zr-2Nd-Y alloy in the peak aged hardness are 293 and 221 MPa at room temperature, 248 and 191 MPa at 230 degrees C. The improvement of age-hardening response and tensile properties is mainly attributed to the quadrate-like stable Mg5RE precipitate, which forms readily and orderly in aged Mg-8Gd-0.6Zr-2Nd-Y alloy.

Electrochemical properties of rare earth AB(3)-type alloy as negative electrode material in MH-Ni battery

Electrochemical properties of rare earth AB(3)-type hydrogen storage alloys as negative electrode material and a polymer instead of 6 M KOH aqueous solution as solid state electrolyte in MH-Ni battery have been investigated at room temperature and 28degreesC first time. The partial replacement of Ni by Al and Mn elements increases the specific capacity and cycle stability of the alloy.

Electrochemical properties of LaAl2 laves phase alloy

The electrochemical performance of Laves phase alloys LaAl2 and LaAl1.5Ni0.5 were investigated. The results showed that LaAl2 alloy milled for 2 hours has the larger discharge capacity than that of as-cast alloy. In addition, partial substitution of Ni for Al will clearly increases the discharge capacity of milled LaAl2 alloy.

Grey interrelation analysis to assess the influence of elements on the galvanic efficiency of Al sacrificial anode

Grey interrelation analysis method was used to study the correlation of Al-anode elements and its galvanic efficiency at 20 degreesC, 40 degreesC and 60 degreesC. Twenty-eight kinds of Al-anodes were made for experiments by the method given by Chinese National Standard GB4948-85 [1] and the correlation degree of elements added in the anodes were calculated. The results showed that the order of elements affecting galvanic efficiency at different temperature is basically the same, and the correlation degree can reflect the variation of Al-anode galvanic efficiency when changing temperature. It is suggested that the elements being added in Al-anode are Zn, In, Ga, Mg.

Effect of alloy elements on the anti-corrosion properties of low alloy steel

Effect of alloy elements on corrosion of low alloy steel was studied under simulated offshore conditions. The results showed that the elements Cu, P, Mo, W, V had evident effect on corrosion resistance in the atmosphere zone; Cu, P, V, Mo in the splash zone and Cr, Al, Mo in the submerged zone.

利用激光诱导击穿光谱对铝合金成分进行多元素同时定量分析

利用激光诱导击穿光谱定量分析了铝合金中多种元素的成分。采用Nd∶YAG脉冲激光器,在空气环境下烧蚀铝合金固体样品获得等离子体。利用多通道光栅光谱仪和CCD检测器对200～980nm波长范围的光谱进行同时检测。研究了检测时延、激光脉冲能量、元素深度分布对光谱强度的影响,考虑这些因素之后对实验参数进行了优化。在优化的实验参数下对国家标准铝合金样品中的八种元素Si,Fe,Cu,Mn,Mg,Zn,Sn及Ni进行了定标,并利用定标曲线对一种铝合金样品进行了定量分析。实验结果表明,测量结果的相对标准偏差(RSD)最大为5.89%,相对误差在-20.99%～15%范围内,说明对铝合金样品成分进行定量分析,激光诱导击穿光谱是一种有效的光谱分析工具,但是分析结果的准确度仍需要提高。

XRD and XPS studies on the ultra-uniform Raney-Ni catalyst prepared from the melt-quenching alloy

We present a novel method for preparing an ultra-uniform Raney-Ni catalyst, which includes melt-quenching, hydrogen treatment and leaching in an alkali solution. The resultant catalyst shows superior activity in the reaction of cyclohexanone hydrogenation. X-ray diffraction (XRD) and XPS have been employed to characterize the catalysts. As demonstrated, the pretreatment with hydrogen caused a distinct phase transfer of the Ni-Al alloys, forming more of the Ni2Al3 component. In the subsequent leaching process, the Ni2Al3 component shows high activity and the resultant catalyst exhibits high surface areas and small pores. Moreover, metallic Al in the hydrogen-pretreated alloy appeared to be leached more easily and thus the aluminium species remaining on the catalyst surface is aluminium oxide predominantly, which serves as a matrix to stabilize active Ni species on the surface. Copyright (C) 2001 John Wiley & Sons, Ltd.

Variaciones temporales en las determinaciones de Ca, Mg y K intercambiables

p.317-323

Fabrication of Ti-Al coatings by mechanical alloying method

By means of the mechanical alloying (MA) method, Al and Ti + Al coatings were deposited on Ti alloy substrates. During the mechano-activation processing, the substrate surface was impacted by a large number of flying balls along with particles of powder. The repeated ball collisions with the substrate resulted in the deposition of powder on its surface. MA technique produced Ti + Al coating with a thickness of 200 µm and Al one with a thickness of 50 µm after 2 h milling at room temperature. The as-synthesized coatings showed structures with high apparent density and free of porosity. The surface morphology of the MA-coatings was very rough. Annealing treatment led to the leveling of this uneven morphology. Annealing at temperatures ranging between 600 °C and 1100 °C gave different aluminide phases on the samples. In the case of Al coating, Al3Ti and Ti3Al compound were observed upon heating up to 1100 °C. In the case of Ti + Al coating, Al3Ti, Al2Ti, TiAl and Ti3Al were formed on the surface.

Adsorption Study using Optimised 3D Organised Mesoporous Silica Coated with Fe and Al Oxides for Specific As(III) and As(V) Removal from Contaminated Synthetic Groundwater

This work presents the possibility of optimising 3D Organised Mesoporous Silica (OMS) coated with both iron and aluminium oxides for the optimal removal of As(III) and As(V) from synthetic contaminated water. The materials developed were fully characterised and were tested for removing arsenic in batch experiments. The effect of total Al to Fe oxides coating on the selective removal of As(III) and As(V) was studied. It was shown that 8% metal coating was the optimal configuration for the coated OMS materials in removing arsenic. The effect of arsenic initial concentration and pH, kinetics and diffusion mechanisms was studied, modelled and discussed. It was shown that the advantage of an organised material over an un-structured sorbent was very limited in terms of kinetic and diffusion under the experimental conditions. It was shown that physisorption was the main adsorption process involved in As removal by the coated OMS. Maximum adsorption capacity of 55 mg As(V).g-1 was noticed at pH 5 for material coated with 8% Al oxides while 35 mg As(V).g-1 was removed at pH 4 for equivalent material coated with Fe oxides.

Aging Behavior of YAl2p/Mg-14Li-1Al Composite

YAl2p/Mg-14Li-1Al composite was made by a stir-casting technique. The aging behavior of the composite was investigated using hardness test, differential scanning calorimetry, and X-ray diffraction. The results show that the microhardness variations of both the matrix alloy and its composite are related to the precipitation and decomposition of θ-MgLi2Al phase. The strengthening of the composite is from the addition of YAl2 particulates and the precipitation in matrix alloy. The former contribution is stable, but the latter is unstable and depends on the aging behavior. The addition of YAl2 particulates delays occurring of the aging behavior of composite.

Variabilidad espacial de la pesquería de Dosidicus gigas (d’Orbigny, 1835) calamar gigante del 2004 al 2012

Se efectuó un análisis de la distribución espacial de operaciones de pesca de la flota calamarera industrial dentro y fuera de la zona económica exclusiva peruana (ZEE) con relación a la temperatura superficial de mar (TSM) y concentración de clorofila-a (Cl-a) para el periodo 2004-2012. La data de operaciones de pesca se dividió en tres periodos en función a distancia a la costa considerando regulaciones de pesca, de enero 2004 a octubre 2010, de noviembre 2010 a diciembre 2011 y 2012. Durante el primer periodo, se identificaron dos patrones mensuales de distribución espacial, de enero a julio fue a lo largo del litoral desde Paita (5°S) hasta San Juan de Marcona (15°22’S) y de agosto a diciembre entre Chimbote y Paita. En el segundo periodo, las operaciones de pesca formaron pequeñas concentraciones y puntos de pesca dispersas debido a la restricción de pesca dentro de las 80 millas náuticas desde noviembre del 2010. Durante el 2012 la flota se localizó fuera de la ZEE. Las mayores concentraciones de la flota se ubicaron entre 30 a 90 millas náuticas de la costa. Mayores concentraciones de pesca se localizaron en Paita-Chimbote (5°-9°S) y Callao- San Juan de Marcona (12°03’-15°22’S). Las faenas de pesca se realizaron en un rango amplio de TSM entre 14,1 y 26,8 °C, con mayor incidencia en temperaturas entre 18,4 a 22 °C, con tendencia a localizarse en áreas de mayor temperatura durante los últimos años. Respecto a la clorofila-a, la flota faenó entre concentraciones de clorofila-a de 0 a 9,5 mg/m3 dentro de la ZEE, y entre 0,2 y 0,5 mg/m3 fuera de la ZEE. Se observó un patrón de distribución de flota, asociado a las anomalías de temperatura superficial de mar del área El Niño 1+2, a la distribución latitudinal y una variabilidad cíclica mensual de la TSM.

Influvence of Alloying Additions on the Structure and Properties of Ai-7Si-0.3Mg Alloy

Cast Ai-Si alloys are widely used in the automotive, aerospace and general engineering industries due to their excellent combination of properties such as good castability, low coefficient of thermal expansion, high strength-to-weight ratio and good corrosion resistance. The present investigation is on the influence of alloying additions on the structure and properties of Ai-7Si-0.3Mg alloy. The primary objective of this present investigation is to study these beneficial effects of calcium on the structure and properties of Ai-7Si-0.3Mg-xFe alloys. The second objective of this work is to study the effects of Mn,Be and Sr addition as Fe neutralizers and also to study the interaction of Mn,Be,Sr and Ca in Ai-7Si-0.3Mg-xFe alloys. In this study the duel beneficial effects of Ca viz;modification and Fe-neutralization, comparison of the effects of Ca and Sr with common Fe neutralizers. The casting have been characterized with respect to their microstructure, %porosity and electrical conductivity, solidification behaviour and mechanical properties. One of the interesting observations in the present work is that a low level of calcium reduces the porosity compared to the untreated alloy. However higher level of calcium addition lead to higher porosity in the casting. An empirical analysis carried out for comparing the results of the present work with those of the other researchers on the effect of increasing iron content on UTS and % elongation of Ai-Si-Mg and Ai-Si-Cu alloys has shown a linear and an inverse first order polynomial relationships respectively.

Correlacion entre bilirrubinometría transcutanea y bilirrubina serica en neonatos a termino o cercanos al termino con ictericia

La ictericia es causa frecuente de hospitalización en neonatos. El objetivo principal fue establecer la correlación entre bilirrubinometría transcutánea y bilirrubina sérica, y su utilidad para identificar requerimiento de fototerapia. Materiales y métodos: Es un estudio descriptivo de correlación. Incluyó neonatos con realización de bilirrubinometría transcutánea y bilirrubina sérica. Se calculan índices de correlación de Pearson para el tórax y la frente. La variabilidad de las diferencias entre niveles transcutáneos y bilirrubina séricas, se correlacionan, mediante diagrama de Bland-Altman. Se obtienen mediciones de desempeño de la prueba, con sensibilidad y especificidad. Resultados: Se incluyeron 88 Neonatos, con 112 bilirrubinometrías transcutáneas, (mediana en tórax: 6,0 mg/dl y en frente: 5,9 mg/dl). Se tomaron 95 muestras de bilirrubina sérica, (mediana: 7,2 mg/dl). Los índices de correlación de Pearson fueron 0.83 (tórax) y 0.93 (frente). Utilizando puntos de corte establecidos, para determinar la necesidad de fototerapia, se obtuvieron, sensibilidad del 93 % y especificidad del 86 % (tórax), y sensibilidad del 94% y especificidad del 83 % (frente). Utilizando percentiles 75 del gráfico de Buthani, se obtuvieron sensibilidad del 83% y Especificidad del 98% para la bilirrubinometría transcutánea. Discusión: Las mediciones transcutáneas se correlacionaron bien con las sanguíneas. Las sensibilidades obtenidas fueron satisfactorias. Conclusión: Las mediciones transcutáneas, hubieran detectado la mayoría de infantes que requirieron fototerapia, confirmando la utilidad como método no invasivo en la práctica clínica.

Factores asociados al desarrollo de formas sintomáticas de hipercalciuria idiopática en niños de la Fundación Cardioinfantil

La hipercalciuria idiopática (HI) es un trastorno metabólico frecuente, con curso clínico, la mayoría de las veces asintomático. Sin embargo, en algunos pacientes se manifiesta clínicamente con hematuria, polaquiuria, disuria, incontinencia urinaria, enuresis y dolor abdominal o lumbar, los cuales afectan las actividades diarias de los niños y motivan consultas médicas repetitivas, con los costos que esto genera. Se requiere de la sospecha clínica y el conocimiento de la enfermedad para su diagnóstico y tratamiento oportunos. Objetivo. Determinar los factores relacionados con el desarrollo de la forma sintomática de HI, para lo cual se estudiaron: la magnitud de la calciuria, el antecedente familiar de urolitiasis, el género, la edad y la excreción de oxalato de calcio. El propósito final fue ampliar y difundir el conocimiento de la enfermedad dentro de la comunidad médica. Materiales y métodos. Se realizó un estudio analítico de casos y controles para determinar la relación existente entre los factores mencionados y la presencia de síntomas de HI. La población de estudio estuvo compuesta por 60 pacientes con diagnóstico establecido de HI, de la consulta de Nefropediatría de la Fundación Cardioinfantil, con edades entre los 2 y los 13 años. La metodología consistió en un estudio no pareado con 1,4 casos por cada control. Para el análisis estadístico de las asociaciones entre los factores en estudio y la HI sintomática se utilizó la prueba exacta de Fisher y el Ji cuadrado de Pearson con un nivel de significancia del 5% (p<0,05). Para establecer la fuerza de la asociación se calculó la razón de disparidad (OR) y el intervalo de confianza del 95%. Además, se determinaron las variables que explican en conjunto la HI sintomática, controlando las variables de confusión con un modelo de regresión logística incondicional a un nivel de significancia del 5% (p<0,05). Resultados. Se establecieron asociaciones entre los siguientes factores y la presencia de síntomas de HI en niños: el género masculino (p = 0,006; OR = 6,2; IC = 1,6-24,5) y la magnitud de la calciuria (p = 0,003). Con menor diferencia estadística se encontraron el antecedente familiar positivo de urolitiasis (p = 0,018; OR = 4,889; IC = 1,26-19,48) y el incremento en la edad (p = 0,044). La presencia de oxalato de calcio en el uroanálisis no se relacionó con los síntomas de HI (p = 0,2; OR = 0,59; IC = 0,17-1,49). Conclusiones. Los valores elevados de calciuria M(mayor a 6 mg/kg/día) y el género masculino, se asocian con la presencia de síntomas de HI en niños. Adicionalmente, se observaron, con frecuencia, en el grupo de pacientes sintomáticos, la presencia de niños de edades mayores y el antecedente familiar positivo de litiasis renal, aunque no se evidencian diferencias significativas para estos dos factores. El hallazgo de cristales de oxalato de calcio en el uroanálisis no se relacionó con los síntomas de HI.