Modelling of Organic Rankine Cycle for Waste Heat Recovery Process in Supercritical Condition

Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.

Porous organic cages for sulfur hexafluoride separation

A series of porous organic cages is examined for the selective adsorption of sulphur hexafluoride (SF6) over nitrogen. Despite lacking any metal sites, a porous cage, CC3, shows the highest SF6/N2 selectivity reported for any material at ambient temperature and pressure, which translates to real separations in a gas breakthrough column. The SF6 uptake of these materials is considerably higher than would be expected from the static pore structures. The location of SF6 within these materials is elucidated by x-ray crystallography, and it is shown that cooperative diffusion and structural rearrangements in these molecular crystals can rationalize their superior SF6/N2 selectivity.

Preparation of new materials by heterogeneous modification of cellulose

O presente trabalho teve como principal objectivo estudar a modificação química heterogénea controlada de fibras de celulose com diferentes reagentes de modo a alterar as suas propriedades de superfície, em especial em termos da criação de um carácter hidrofóbico e lipofóbico, preservando, sempre que possível, as suas propriedades mecânicas e, consequentemente, abrindo novas perspectivas de aplicação. O desenvolvimento do trabalho envolveu três abordagens principais, envolvendo, em cada caso, o estudo de diferentes condições reaccionais. Na primeira abordagem foram utilizados como reagentes de modificação compostos perfluorados, nomeadamente o anidrido trifluoroacético (TFAA), o cloreto de 2,3,4,5,6-pentafluorobenzoílo (PFBz) e o cloreto de 3,3,3- trifluoropropanoílo (TFP), para promover a acilação heterogénea da superfície das fibras. A segunda estratégia usada consistiu na preparação de híbridos de celulose do tipo orgânico-inorgânico classe-II, através da modificação das fibras de celulose com o (3-isocianatopropil)trietoxissilano (ICPTEOS), um reagente organossilano bifuncional. A ligação às fibras de celulose foi efectuada através das funções isocianato e, posteriormente, os grupos etoxissilano foram sujeitos a tratamentos de hidrólise ácida, como tal ou na presença de outros siloxanos, nomeadamente o tetraetoxissilano (TEOS) e o 1H,1H,2H,2Hperfluorodeciltrietoxissilano (PFDTEOS). Finalmente, a última abordagem foi baseada na modificação das fibras com triclorometilssilano (TCMS), através de uma reacção gás-sólido, que dispensou assim o uso de solventes orgânicos. A ocorrência de modificação química foi em cada caso confirmada por Espectroscopia de Infravermelho com Transformada de Fourier e Reflectância Total Atenuada (FTIR-ATR), Análise Elementar (EA) e determinação de ângulos de contacto. Adicionalmente, e dependendo de cada caso específico, diversas outras técnicas foram empregues na caracterização aprofundada dos materiais preparados, nomeadamente Ressonância Magnética Nuclear CPMAS no Estado Sólido (RMN), Espectroscopia de Difracção de Raios-X (XRD), Análise Termogravimétrica (TGA), Espectrometria de Massa de Iões Secundários com Análise de Tempo de Vôo (ToF-SIMS), Espectroscopia Fotoelectrónica de Raios-X (XPS) e Microscopia Electrónica de Varrimento (SEM). Relativamente à acilação das fibras de celulose com reagentes perfluorados, o sucesso da reacção foi comprovado por FTIR-ATR, EA, XPS e ToF-SIMS. Neste contexto, obtiveram-se fibras modificadas possuindo graus de substituição (DS) compreendidos entre 0.006 e 0.39. Verificou-se por XRD que, em geral, mesmo para os valores de DS mais elevados, a cristalinidade das fibras não foi afectada, indicando que a modificação foi limitada às camadas mais superficiais das mesmas ou a regiões amorfas das suas camadas mais internas. Adicionalmente, observou-se por ToF-SIMS que a distribuição dos grupos perfluorados à superfície das fibras foi, de facto, bastante heterogénea. Todos os derivados de celulose perfluorados apresentaram elevada hidrofobicidade e lipofobicidade, tendo-se atingido ângulos de contacto com água e diiodometano de 126º e 104º, respectivamente. Um aspecto interessante relativo a estes materiais é que a elevada omnifobicidade foi observada mesmo para valores de DS muito reduzidos, não se mostrando significativamente afectada pelo aumento dos mesmos. Em consonância, verificou-se por XPS que a cobertura da superfície das fibras de celulose com grupos perfluorados aumentou apenas ligeiramente com o aumento do DS, apontando para a esterificação de camadas mais internas das fibras, associada, neste caso, predominantemente aos seus domínios amorfos. No que diz respeito à estabilidade hidrolítica destes derivados, obtiveram-se dois tipos distintos de comportamento. Por um lado, as fibras de celulose trifluoroacetiladas são facilmente hidrolisáveis em meio neutro, e, por outro, as fibras pentafluorobenzoiladas e trifluoropropanoiladas mostram-se bastante resistentes face a condições de hidrólise em meio neutro e ácido (pH 4), podendo, contudo, ser facilmente hidrolisadas em meio alcalino (pH 9 e 12, para derivados do PFBz e do TFP, respectivamente). Na segunda abordagem verificou-se a ocorrência de reacção por FTIR-ATR e EA. Em geral, a modificação química com ICPTEOS ocorre predominantemente nas zonas mais superficiais das fibras de celulose ou em regiões amorfas. Contudo, em condições reaccionais mais severas (maior quantidade de reagente e tempo de reacção), esta atingiu também regiões cristalinas, afectando, consequentemente, a estrutura cristalina das fibras, como verificado por XRD. Por RMN de 29Si observou-se que após reacção com o ICPTEOS já existiam indícios de alguma hidrólise dos grupos etoxissilano, e que a sua subsequente condensação parcial tinha levado à formação de uma película inorgânica em redor das fibras (verificado por SEM), constituída maioritariamente por estruturas lineares, com uma contribuição mais modesta de estruturas “diméricas” e outras mais ramificadas. Consequentemente, este revestimento inorgânico transformou as fibras de celulose em materiais híbridos com elevada hidrofobicidade (ângulos de contacto com água entre 103-129º). A hidrólise ácida dos restantes grupos etoxissilano, como tal ou na presença de TEOS, originou híbridos de celulose com elevada hidrofilicidade, sendo impossível medirem-se os ângulos de contacto com água dos produtos finais, devido à presença maioritária de grupos silanol (Si-OH) e ligações Si-O-Si à superfície, os quais contribuíram para o consequente aumento de energia de superfície. No entanto, quando a hidrólise foi realizada na presença de PFDTEOS, obtiveram-se materiais híbridos com elevada hidrofobicidade e lipofobicidade (ângulos de contacto com água e diiodometano de 140º e 134º, respectivamente), devido à combinação da presença de grupos perfluorados e micro- e nano-rugosidades na superfície das fibras de celulose, conforme confirmado por SEM. Finalmente, a última abordagem permitiu preparar materiais derivados de celulose altamente hidrofóbicos e lipofóbicos (ângulos de contacto com água e diiodometano de 136º e 109º, respectivamente) por um processo simples, envolvendo tempos de tratamento tão curtos como 0.5 min. Este comportamento omnifóbico foi gerado pelo efeito sinergético entre a diminuição de energia de superfície das fibras, devido à presença de grupos metilo dos resíduos de TCMS ligados a estas, e a condensação dos resíduos de TCMS na forma de micro- e nano-partículas inorgânicas, que levou à criação de um revestimento rugoso à superfície das fibras, conforme observado por RMN de 29Si e SEM, respectivamente. A pré-humidificação das fibras de celulose demonstrou desempenhar um importante papel de “acelerador” dos processos de hidrólise e condensação das moléculas de TCMS. Nestas condições, o tempo de tratamento foi um dos parâmetros mais relevantes, pois para tempos de tratamento muito curtos (0.5 min) os materiais resultantes não apresentaram quaisquer diferenças a nível de propriedades físico-químicas em relação ao substrato de partida (a humidade em excesso consumiu todo o TCMS antes que este conseguisse reagir com os grupos hidroxilo das fibras de celulose), possuindo, por exemplo, valores de ângulos de contacto com água idênticos. Para tempos de tratamento mais longos, como 30 min, os materiais finais apresentaram a maior quantidade de componentes inorgânicos, tal como verificado por EA e TGA. Assim, o controlo da humidade das fibras é imperativo para se poder moldar as propriedades finais dos produtos. Esta última abordagem é particularmente promissora uma vez que tem como base um sistema simples e “verde” que pode ser facilmente implementado. Em conclusão, este trabalho permitiu demonstrar que a modificação química heterogénea controlada das fibras de celulose representa uma iniciativa promissora para a preparação de novos materiais obtidos a partir de recursos renováveis, com propriedades interessantes e passíveis de ser potencialmente aplicados em diferentes áreas. Para além do mais, as estratégias de modificação estudadas podem também ser precursoras de novos estudos que possam vir a ser desenvolvidos dentro do mesmo âmbito.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Lanthanide-organic frameworks for optical and catalytic applications

Este projecto de doutoramento tem como objetivo isolar e caracterizar sistematicamente novos polímeros de coordenação, no estado sólido. A presença de grupos rígidos possuindo, em particular, átomos de oxigénio e de azoto, deverá induzir interessantes propriedades fotoluminescentes (rendimentos quânticos e tempos de vida elevados, assim como vias de transferência de energia eficientes), que poderão permitir a utilização dos compostos poliméricos na produção de dispositivos funcionais. As diferentes abordagens sintéticas foram ajustadas para cada material e basearam-se, preferencialmente, nas sínteses hidrotérmicas e nas assistidas por radiação de microondas. A estrutura dos materiais foi elucidada a partir de métodos de difracção de raios X (de cristal único ou de pós) em conjunto com outras técnicas, tais como RMN de estado sólido, microscopia eletrónica, análises térmicas, espectroscopia vibracional e estudos de composição elementar. Os compostos microcristalinos foram sistematicamente estudados a fim de investigar outras propriedades além das de fotoluminescência. Alguns dos materiais revelaram multifuncionalidade apresentando simultaneamente tempos de vida na ordem dos milisegundos, elevados rendimentos quânticos e elevado desempenho como catalisadores heterogéneos. As propriedades magnéticas de um composto baseado em érbio foram igualmente estudadas, assim como as de adsorpção e permuta de solvente de uma estrutura porosa baseada em cério.

Metal-organic frameworks based on phosphonate linkers

During the last few decades, Metal-Organic Frameworks (MOFs), also known as Coordination Polymers, have attracted worldwide research attentions due to their incremented fascinating architectures and unique properties. These multidimensional materials have been potential applications in distinct areas: gas storage and separation, ion exchange, catalysis, magnetism, in optical sensors, among several others. The MOF research group at the University of Aveiro has prepared MOFs from the combination of phosphonate organic primary building units (PBUs) with, mainly, lanthanides. This thesis documents the last findings in this area involving the synthesis of multidimensional MOFs based on four di- or tripodal phosphonates ligands. The organic PBUs were designed and prepared by selecting and optimizing the best reaction conditions and synthetic routes. The self-assembly between phosphonate PBUs and rare-earths cations led to the formation of several 1D, 2D and 3D families of isotypical MOFs. The preparation of these materials was achieved by using distinct synthetic approaches: hydro(solvo)thermal, microwave- and ultrasound-assisted, one-pot and ionothermal synthesis. The selection of the organic PBUs showed to have an important role in the final architectures: while flexible phosphonate ligands afforded 1D, 2D and dense 3D structures, a large and rigid organic PBU isolated a porous 3D MOF. The crystal structure of these materials was successfully unveiled by powder or single-crystal X-ray diffraction. All multidimensional MOFs were characterized by standard solid-state techniques (FT-IR, electron microscopy (SEM and EDS), solid-state NMR, elemental and thermogravimetric analysis). Some MOF materials exhibited remarkable thermal stability and robustness up to ca. 400 ºC. The intrinsic properties of some MOFs were investigated. Photoluminescence studies revealed that the selected organic PBUs are suitable sensitizers of Tb3+ leading to the isolation of intense green-emitting materials. The suppression of the O−H quenchers by deuteration or dehydration processes improves substantially the photoluminescence of the optically-active Eu3+-based materials. Some MOF materials exhibited high heterogeneous catalytic activity and excellent regioselectivity in the ring-opening reaction of styrene oxide (PhEtO) with methanol (100% conversion of PhEtO at 55 ºC for 30 min). The porous MOF material was employed in gas separation processes. This compound showed the ability to separate propane over propylene. The ionexchanged form of this material (containing K+ cations into its network) exhibited higher affinity for CO2 being capable to separate acetylene over this environment non-friendly gas.

Characterization of water-soluble organic matter from urban aerosols

Water-soluble organic matter (WSOM) from atmospheric particles comprises a complex array of molecular structures that play an important role on the physic-chemical properties of atmospheric particles and, therefore, are linked to several global-relevant atmospheric processes which impact the climate and public health. Due to the large variety of sources and formation processes, adequate knowledge on WSOM composition and its effects on the properties of atmospheric aerosol are still limited. Therefore, this thesis aims at providing new insights on the molecular composition of WSOM from fine atmospheric aerosols typical of an urban area (Aveiro, Portugal). In a first step, adsorption phenomena of semivolatile organic compounds on quartz fibre filters employed in the collection of atmospheric aerosols were assessed. Afterwards, atmospheric aerosol samples were collected during fifteen months, on a weekly basis. A mass balance of aerosol samples was performed in order to set the relative contribution of elemental carbon, WSOM and water-insoluble organic matter to the aerosol mass collected at the urban area of Aveiro, with a special focus on the assessment of the influence of different meteorological conditions. In order to assess the chemical complexity of the WSOM from urban aerosols, their structural characteristics were studied by means of Fourier transform infrared infrared - Attenuated Total Reflectance (FTIR-ATR) and solid-state cross polarization with magic angle spinning 13C nuclear magnetic resonance (CPMAS 13C NMR) spectroscopies, as well as their elemental composition. The structural characterization of aerosol WSOM samples collected in the urban area highlighted a highly complex mixture of functional groups. It was concluded that aliphatic and aromatic structures, hydroxyl groups and carboxyl groups are characteristic to all samples. The semi-quantitative assessment of the CPMAS 13C NMR data showed different distributions of the various functional groups between the aerosol samples collected at different seasons. Moreover, the presence of signals typical of lignin-derived structures in both CPMAS 13C NMR and FTIR-ATR spectra of the WSOM samples from the colder seasons, highlights the major contribution of biomass burning processes in domestic fireplaces, during low temperature conditions, into the bulk chemical properties of WSOM from urban aerosols. A comprehensive two-dimensional liquid chromatography (LC x LC) method, on-line coupled to a diode array, fluorescence, and evaporative light scattering detectors, was employed for resolving the chemical heterogeneity of the aerosol WSOM samples and, simultaneously, to map the hydrophobicity versus the molecular weight distribution of the samples. The LC x LC method employed a mixed-mode hydrophilic interaction column operating under aqueous reversed phase mode in the first dimension, and a size-exclusion column in the second dimension, which was found to be useful for separating the aerosol WSOM samples into various fractions with distinct molecular weight and hydrophobic features. The estimative of the average molecular weight (Mw) distribution of the urban aerosol WSOM samples ranged from 48 to 942 Da and from 45 to 1241 Da in terms of UV absorption and fluorescence detection, respectively. Findings suggest that smaller Mw group fractions seem to be related to a more hydrophobic nature.

Methylamine as true template and TEAOH as purifying agent: unexpected roles of current organic additives in the hydrothermal synthesis of microporous aluminophosphates

Methylamine (MA), TEA+ and water were shown to play a concerted role during the synthesis of two new aluminophosphates IST-1 and IST-2. Both structures start to nucleate after the dramatic change of the gel composition due to preliminary interactions between TEA+ cations.

Detection of explosive vapors using organic thin-film transistors

Field effect transistors (FETs) based on organic materials were investigated as sensors for detecting 2,4,6-trinitrotoluene (TNT) vapors. Several FET devices were fabricated using two types of semiconducting organic materials, solution processed polymers deposited by spin coating and, oligomers (or small molecules) deposited by vacuum sublimation. When vapors of nitroaromatic compounds bind to thin films of organic materials which form the transistor channel, the conductivity of the thin film increases and changes the transistor electrical characteristic. The use of the amplifying properties of the transistor represents a major advantage over conventional techniques based on simple changes of resistance in polymers frequently used in electronic noses.

Accounting for the dissociating properties of organic chemicals in LCIA: an uncertainty analysis applied to micropollutants in the assessment of freshwater ecotoxicity

In life cycle impact assessment (LCIA) models, the sorption of the ionic fraction of dissociating organic chemicals is not adequately modeled because conventional non-polar partitioning models are applied. Therefore, high uncertainties are expected when modeling the mobility, as well as the bioavailability for uptake by exposed biota and degradation, of dissociating organic chemicals. Alternative regressions that account for the ionized fraction of a molecule to estimate fate parameters were applied to the USEtox model. The most sensitive model parameters in the estimation of ecotoxicological characterization factors (CFs) of micropollutants were evaluated by Monte Carlo analysis in both the default USEtox model and the alternative approach. Negligible differences of CFs values and 95% confidence limits between the two approaches were estimated for direct emissions to the freshwater compartment; however the default USEtox model overestimates CFs and the 95% confidence limits of basic compounds up to three orders and four orders of magnitude, respectively, relatively to the alternative approach for emissions to the agricultural soil compartment. For three emission scenarios, LCIA results show that the default USEtox model overestimates freshwater ecotoxicity impacts for the emission scenarios to agricultural soil by one order of magnitude, and larger confidence limits were estimated, relatively to the alternative approach.

New end-use application for GFRP recyclates as reinforcement for concrete-polymer materials’

Glass fibre-reinforced plastics (GFRP), nowadays commonly used in the construction, transportation and automobile sectors, have been considered inherently difficult to recycle due to both: cross-linked nature of thermoset resins, which cannot be remolded, and complex composition of the composite itself, which includes glass fibres, matrix and different types of inorganic fillers. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. There are several methods to recycle GFR thermostable materials: (a) incineration, with partial energy recovery due to the heat generated during organic part combustion; (b) thermal and/or chemical recycling, such as solvolysis, pyrolisis and similar thermal decomposition processes, with glass fibre recovering; and (c) mechanical recycling or size reduction, in which the material is subjected to a milling process in order to obtain a specific grain size that makes the material suitable as reinforcement in new formulations. This last method has important advantages over the previous ones: there is no atmospheric pollution by gas emission, a much simpler equipment is required as compared with ovens necessary for thermal recycling processes, and does not require the use of chemical solvents with subsequent environmental impacts. In this study the effect of incorporation of recycled GFRP waste materials, obtained by means of milling processes, on mechanical behavior of polyester polymer mortars was assessed. For this purpose, different contents of recycled GFRP waste materials, with distinct size gradings, were incorporated into polyester polymer mortars as sand aggregates and filler replacements. The effect of GFRP waste treatment with silane coupling agent was also assessed. Design of experiments and data treatment were accomplish by means of factorial design and analysis of variance ANOVA. The use of factorial experiment design, instead of the one-factor-at-a-time method is efficient at allowing the evaluation of the effects and possible interactions of the different material factors involved. Experimental results were promising toward the recyclability of GFRP waste materials as aggregates and filler replacements for polymer mortar, with significant gain of mechanical properties with regard to non-modified polymer mortars.

Novel LTCC-potentiometric microfluidic device for biparametric analysis of organic compounds carrying plastic antibodies as ionophores: Application to sulfamethoxazole and trimethoprim

Monitoring organic environmental contaminants is of crucial importance to ensure public health. This requires simple, portable and robust devices to carry out on-site analysis. For this purpose, a low-temperature co-fired ceramics (LTCC) microfluidic potentiometric device (LTCC/μPOT) was developed for the first time for an organic compound: sulfamethoxazole (SMX). Sensory materials relied on newly designed plastic antibodies. Sol–gel, self-assembling monolayer and molecular-imprinting techniques were merged for this purpose. Silica beads were amine-modified and linked to SMX via glutaraldehyde modification. Condensation polymerization was conducted around SMX to fill the vacant spaces. SMX was removed after, leaving behind imprinted sites of complementary shape. The obtained particles were used as ionophores in plasticized PVC membranes. The most suitable membrane composition was selected in steady-state assays. Its suitability to flow analysis was verified in flow-injection studies with regular tubular electrodes. The LTCC/μPOT device integrated a bidimensional mixer, an embedded reference electrode based on Ag/AgCl and an Ag-based contact screen-printed under a micromachined cavity of 600 μm depth. The sensing membranes were deposited over this contact and acted as indicating electrodes. Under optimum conditions, the SMX sensor displayed slopes of about −58.7 mV/decade in a range from 12.7 to 250 μg/mL, providing a detection limit of 3.85 μg/mL and a sampling throughput of 36 samples/h with a reagent consumption of 3.3 mL per sample. The system was adjusted later to multiple analyte detection by including a second potentiometric cell on the LTCC/μPOT device. No additional reference electrode was required. This concept was applied to Trimethoprim (TMP), always administered concomitantly with sulphonamide drugs, and tested in fish-farming waters. The biparametric microanalyzer displayed Nernstian behaviour, with average slopes −54.7 (SMX) and +57.8 (TMP) mV/decade. To demonstrate the microanalyzer capabilities for real applications, it was successfully applied to single and simultaneous determination of SMX and TMP in aquaculture waters.

Molecular simulation of gas adsorption equilibria in nanoporous materials

This work is divided into two distinct parts. The first part consists of the study of the metal organic framework UiO-66Zr, where the aim was to determine the force field that best describes the adsorption equilibrium properties of two different gases, methane and carbon dioxide. The other part of the work focuses on the study of the single wall carbon nanotube topology for ethane adsorption; the aim was to simplify as much as possible the solid-fluid force field model to increase the computational efficiency of the Monte Carlo simulations. The choice of both adsorbents relies on their potential use in adsorption processes, such as the capture and storage of carbon dioxide, natural gas storage, separation of components of biogas, and olefin/paraffin separations. The adsorption studies on the two porous materials were performed by molecular simulation using the grand canonical Monte Carlo (μ,V,T) method, over the temperature range of 298-343 K and pressure range 0.06-70 bar. The calibration curves of pressure and density as a function of chemical potential and temperature for the three adsorbates under study, were obtained Monte Carlo simulation in the canonical ensemble (N,V,T); polynomial fit and interpolation of the obtained data allowed to determine the pressure and gas density at any chemical potential. The adsorption equilibria of methane and carbon dioxide in UiO-66Zr were simulated and compared with the experimental data obtained by Jasmina H. Cavka et al. The results show that the best force field for both gases is a chargeless united-atom force field based on the TraPPE model. Using this validated force field it was possible to estimate the isosteric heats of adsorption and the Henry constants. In the Grand-Canonical Monte Carlo simulations of carbon nanotubes, we conclude that the fastest type of run is obtained with a force field that approximates the nanotube as a smooth cylinder; this approximation gives execution times that are 1.6 times faster than the typical atomistic runs.

Spin labile conducting metallopolymers : a new architecture for hybrid multifunctional materials

The synthesis of 3-ethynylthienyl- (2.07), 3-ethynylterthienyl- (2.19) substituted qsal [qsalH = N-(8-quinolyl)salicylaldimine] and 3,3' -diethynyl-2,2' -bithienyl bridging bisqsal (5.06) ligands are described along with the preparation and characterization of eight cationic iron(III) complexes containing these ligands with a selection of counteranions [(2.07) with: SCN- (2.08), PF6- (2.09), and CI04- (2.10); (2.19) with PF6 - (2.20); (5.06) with: cr (5.07), SeN- (5.08), PF6- (5.09), and CI04- (5.10)]. Spin-crossover is observed in the solid state for (2.08) - (2.10) and (5.07) - (5.10), including a ve ry rare S = 5/2 to 3/2 spin-crossover in complex (2.09). The unusal reduction of complex (2.10) produces a high-spin iron(I1) complex (2.12). Six iron(II) complexes that are derived from thienyl analogues of bispicen [bispicen = bis(2-pyridylmethyl)-diamine] [2,5-thienyl substituents = H- (3.11), Phenyl- (3.12), 2- thienyl (3.13) or N-phenyl-2-pyridinalimine ligands [2,5-phenyl substituents = diphenyl (3.23), di(2-thienyl) (3.24), 4-phenyl substituent = 3-thienyl (3.25)] are reported Complexes (3.11), (3.23) and (3.25) display thermal spin-crossover in the solid state and (3.12) remains high-spin at all temperatures. Complex (3.13) rearranges to form an iron(II) complex (3.14) with temperature dependent magnetic properties be s t described as a one-dimensional ferromagnetic chain, with interchain antiferromagnetic interactions and/or ZFS dominant at low temperatures. Magnetic succeptibility and Mossbauer data for complex (3.24) display a temperature dependent mixture of spin isomers. The preparation and characterization of two cobalt(II) complexes containing 3- ethynylthienyl- (4.04) and 3-ethynylterhienyl- (4.06) substituted bipyridine ligands [(4.05): [Co(dbsqh(4.04)]; (4.07): [Co(dbsq)2(4.06)]] [dbsq = 3,5-dbsq=3,5-di-tert-butylI ,2-semiquinonate] are reported. Complexes (4.05) and (4.07) exhibit thermal valence tautomerism in the solid state and in solution. Self assembly of complex (2.10) into polymeric spheres (6.11) afforded the first spincrossover, polydisperse, micro- to nanoscale material of its kind. . Complexes (2.20), (3.24) and (4.07) also form polymers through electrochemical synthesis to produce hybrid metaUopolymer films (6.12), (6.15) and (6.16), respectively. The films have been characterized by EDX, FT-IR and UV-Vis spectroscopy. Variable-temperature magnetic susceptibility measurements demonstrate that spin lability is operative in the polymers and conductivity measurements confirm the electron transport properties. Polymer (6.15) has a persistent oxidized state that shows a significant decrease in electrical resistance.