Application and development of numerical methods for the modelling of innovative gas cooled fission reactors

Innovative gas cooled reactors, such as the pebble bed reactor (PBR) and the gas cooled fast reactor (GFR) offer higher efficiency and new application areas for nuclear energy. Numerical methods were applied and developed to analyse the specific features of these reactor types with fully three dimensional calculation models. In the first part of this thesis, discrete element method (DEM) was used for a physically realistic modelling of the packing of fuel pebbles in PBR geometries and methods were developed for utilising the DEM results in subsequent reactor physics and thermal-hydraulics calculations. In the second part, the flow and heat transfer for a single gas cooled fuel rod of a GFR were investigated with computational fluid dynamics (CFD) methods. An in-house DEM implementation was validated and used for packing simulations, in which the effect of several parameters on the resulting average packing density was investigated. The restitution coefficient was found out to have the most significant effect. The results can be utilised in further work to obtain a pebble bed with a specific packing density. The packing structures of selected pebble beds were also analysed in detail and local variations in the packing density were observed, which should be taken into account especially in the reactor core thermal-hydraulic analyses. Two open source DEM codes were used to produce stochastic pebble bed configurations to add realism and improve the accuracy of criticality calculations performed with the Monte Carlo reactor physics code Serpent. Russian ASTRA criticality experiments were calculated. Pebble beds corresponding to the experimental specifications within measurement uncertainties were produced in DEM simulations and successfully exported into the subsequent reactor physics analysis. With the developed approach, two typical issues in Monte Carlo reactor physics calculations of pebble bed geometries were avoided. A novel method was developed and implemented as a MATLAB code to calculate porosities in the cells of a CFD calculation mesh constructed over a pebble bed obtained from DEM simulations. The code was further developed to distribute power and temperature data accurately between discrete based reactor physics and continuum based thermal-hydraulics models to enable coupled reactor core calculations. The developed method was also found useful for analysing sphere packings in general. CFD calculations were performed to investigate the pressure losses and heat transfer in three dimensional air cooled smooth and rib roughened rod geometries, housed inside a hexagonal flow channel representing a sub-channel of a single fuel rod of a GFR. The CFD geometry represented the test section of the L-STAR experimental facility at Karlsruhe Institute of Technology and the calculation results were compared to the corresponding experimental results. Knowledge was gained of the adequacy of various turbulence models and of the modelling requirements and issues related to the specific application. The obtained pressure loss results were in a relatively good agreement with the experimental data. Heat transfer in the smooth rod geometry was somewhat under predicted, which can partly be explained by unaccounted heat losses and uncertainties. In the rib roughened geometry heat transfer was severely under predicted by the used realisable k − epsilon turbulence model. An additional calculation with a v2 − f turbulence model showed significant improvement in the heat transfer results, which is most likely due to the better performance of the model in separated flow problems. Further investigations are suggested before using CFD to make conclusions of the heat transfer performance of rib roughened GFR fuel rod geometries. It is suggested that the viewpoints of numerical modelling are included in the planning of experiments to ease the challenging model construction and simulations and to avoid introducing additional sources of uncertainties. To facilitate the use of advanced calculation approaches, multi-physical aspects in experiments should also be considered and documented in a reasonable detail.

Two-phase flow measurements with spacer grid in a rod bundle geometry

Heat transfer effectiveness in nuclear rod bundles is of great importance to nuclear reactor safety and economics. An important design parameter is the Critical Heat Flux (CHF), which limits the transferred heat from the fuel to the coolant. The CHF is determined by flow behaviour, especially the turbulence created inside the fuel rod bundle. Adiabatic experiments can be used to characterize the flow behaviour separately from the heat transfer phenomena in diabatic flow. To enhance the turbulence, mixing vanes are attached to spacer grids, which hold the rods in place. The vanes either make the flow swirl around a single sub-channel or induce cross-mixing between adjacent sub-channels. In adiabatic two-phase conditions an important phenomenon that can be investigated is the effect of the spacer on canceling the lift force, which collects the small bubbles to the rod surfaces leading to decreased CHF in diabatic conditions and thus limits the reactor power. Computational Fluid Dynamics (CFD) can be used to simulate the flow numerically and to test how different spacer configurations affect the flow. Experimental data is needed to validate and verify the used CFD models. Especially the modeling of turbulence is challenging even for single-phase flow inside the complex sub-channel geometry. In two-phase flow other factors such as bubble dynamics further complicate the modeling. To investigate the spacer grid effect on two-phase flow, and to provide further experimental data for CFD validation, a series of experiments was run on an adiabatic sub-channel flow loop using a duct-type spacer grid with different configurations. Utilizing the wire-mesh sensor technology, the facility gives high resolution experimental data in both time and space. The experimental results indicate that the duct-type spacer grid is less effective in canceling the lift force effect than the egg-crate type spacer tested earlier.

A new model for the immobilization of the rat hind limb

An alternative device for the immobilization of the hind limb of the rat was developed to study the effects of chronic disuse on the soleus and tibialis anterior muscles, maintained for 3 weeks in the shortening and the stretching positions, respectively. The proposed device is made of steel mesh and cotton materials, and has some advantages when compared to cast or plaster cast: it is cheaper, lighter (12 g or 4% of the body weight of the rat) and the same unit can be easily adjusted and used several times in the same animal or in animals of similar size. Immobilization is also useful to restrain the movements of the hip, knee, and ankle joints. Male rats (291 ± 35 g and aged 14 ± 2 weeks) were used to develop and test the model. The soleus muscle of 18 rats was maintained in a shortened position for 21 consecutive days and lost 19 ± 7% of its length (P = 0.008) and 44 ± 6% of its weight (P = 0.002) compared to the contralateral intact muscle. No difference (P = 0.67) was found in the stretched tibialis anterior of the same hind limb when compared to the contralateral muscle. No ulcer, sore or foot swelling was observed in the animals. Immobilization was effective in producing chronic muscle disuse in the hind limbs of rats and is an acceptable alternative to the traditional methods of immobilization such as cast or plaster cast.

Novel retrograde puncture method to establish preperitoneal space for laparoscopic direct inguinal hernia repair with internal ring suturing

The aim of this study was to explore the clinical efficacy of a novel retrograde puncture approach to establish a preperitoneal space for laparoscopic direct inguinal hernia repair with inguinal ring suturing. Forty-two patients who underwent laparoscopic inguinal hernia repair with retrograde puncture for preperitoneal space establishment as well as inguinal ring suturing between August 2013 and March 2014 at our hospital were enrolled. Preperitoneal space was successfully established in all patients, with a mean establishment time of 6 min. Laparoscopic repairs were successful in all patients, with a mean surgical time of 26±15.1 min. Mean postoperative hospitalization duration was 3.0±0.7 days. Two patients suffered from postoperative local hematomas, which were relieved after puncturing and drainage. Four patients had short-term local pain. There were no cases of chronic pain. Patients were followed up for 6 months to 1 year, and no recurrence was observed. Our results demonstrate that preperitoneal space established by the retrograde puncture technique can be successfully used in adult laparoscopic hernioplasty to avoid intraoperative mesh fixation, and thus reduce medical costs.

THE EFFECTIVE DIFFUSIVITY OF CLOVE(Eugenia caryophyllus) ESSENTIAL OIL IN PRESSURIZED CO2

The effective diffusivity of clove essential oil in subcritical liquid CO2 was estimated. The experimental apparatus employed was a fixed-bed extractor. The fixed bed was formed with grounded (mesh -32 + 65) and compacted clove buds which were considered a solid element. The effective diffusion coefficient was evaluated by fitting the experimental concentration profile to the unsteady state mass balance equation for unidirectional diffusion in a finite solid medium. The diffusion coefficient was related to the concentration of oil in the solid by an exponential function. The estimated values of the effective diffusion coefficient varied from 3.64 to 5.22x10-10 m2/s. The average relative errors were lower than 3.1%.

Composição química e classes de lipídios em peixe de água doce Curimatã comum, Prochilodus cearensis

O presente trabalho teve como objetivo obter dados quantitativos sobre as classes de lipídios presentes no filé de curimatã, Prochilodus cearensis. Os lipídios totais (LT) foram fracionados em classes de lipídios neutros (LN), gliceroglicolipídios (GL) e glicerofosfolipídios (PL) através de cromatografia em coluna aberta de sílica gel 60 (70-230 mesh). As análises foram realizadas em quatro lotes de amostras contendo cada uma três exemplares, adquiridos em feiras livres de Fortaleza-CE, nos meses de março, maio, junho e julho de 1998. Os LT representaram em média 3,8% em relação ao peso fresco da amostra. A classe lipídica dominante foi de LN com média de 75,1% dos LT ou 2,9g/100g de filé. Os GL e PL contribuíram em média com 1,6% (61mg/100g de filé) e 23,3% (885mg/100g de filé), respectivamente. A composição química centesimal apresentou média de 76,3% de umidade, 18,6% de proteína total e 1,3% de cinza.

Simulation model of wind turbine gearbox and lubrication system

As increasing efficiency of a wind turbine gearbox, more power can be transferred from rotor blades to generator and less power is used to cause wear and heating in the gearbox. By using a simulation model, behavior of the gearbox can be studied before creating expensive prototypes. The objective of the thesis is to model a wind turbine gearbox and its lubrication system to study power losses and heat transfer inside the gearbox and to study the simulation methods of the used software. Software used to create the simulation model is Siemens LMS Imagine.Lab AMESim, which can be used to create one-dimensional mechatronic system simulation models from different fields of engineering. When combining components from different libraries it is possible to create a simulation model, which includes mechanical, thermal and hydraulic models of the gearbox. Results for mechanical, thermal, and hydraulic simulations are presented in the thesis. Due to the large scale of the wind turbine gearbox and the amount of power transmitted, power loss calculations from AMESim software are inaccurate and power losses are modelled as constant efficiency for each gear mesh. Starting values for simulation in thermal and hydraulic simulations were chosen from test measurements and from empirical study as compact and complex design of gearbox prevents accurate test measurements. In further studies to increase the accuracy of the simulation model, components used for power loss calculations needs to be modified and values for unknown variables are needed to be solved through accurate test measurements.

Elementtikoon vaikutus väsymismenetelmien tarkkuuteen

Kandidaatintyössä tutkittiin kolmen hitsatun palstalevyliitoksen väsymiskestävyyttä äärellisten elementtien menetelmällä. Tutkimuksen pääpaino oli 2D-mallin antamien tulosten suppenevuudessa kolmella eri elementtikoolla ja kolmessa eri mittasuhdetapauksessa. Tutkimustuloksissa havaittiin noin 5 % muutos harvimman ja tiheimmän elementtiverkon tulosten välillä. Tutkimuksessa havaittiin myös että muutos harvimman ja tiheimmän elementtiverkon tuloksissa pieneni hiukan mitä suurempia kappaleet ja niiden hitsausliitokset olivat.

Evaluation of the quality of a molded sweet biscuit enriched with okara flour

The objective of this research was to test the addition of soymilk residue, also known as okara, to a molded sweet biscuit (MSB). The okara was provided by two soymilk producing companies whose production systems are based on hot disintegration of decorticated (company B) or non-decorticated (company A) soybeans and separation of the soymilk. Okaras A and B were dehydrated in a flash dryer and then ground to a flour (< 200 mesh). The okara flours showed high protein (35 g.100 g-1 dwb), lipid (17 g.100 g-1 dwb), and fiber (17 to 21 g.100 g-1 dwb) contents. The water holding capacity, protein solubility, emulsifying capacity, emulsion stability and isoflavone contents found in flour A were significantly higher (p < 0.05) than in flour B. The formulation of MSB, replacing 30% (w/w) of the wheat flour with okara flour was tested. The results of the physical measurements, brittleness and water activity of the MSB with flours A and B did not differ significantly (p < 0.05) from those of the standard. The color, flavor and overall quality of the MSB with 30% of okara flour B did not differ significantly from those of the standard biscuit, demonstrating its potential for application in confectionery products.

Microbiological quality of meals served in nursing homes in the city of Ponta Grossa, Paraná

Abstract The aim of this study was to analyze the microbiological quality of meals served in nursing homes in the city of Ponta Grossa, Paraná, before and after the training of food handlers. The first stage was to perform a checklist conforming with current legislation. The second consisted of the collection of 4 food samples from each location and a microbiological investigation in accordance with the relevant legislation. The third was the training of food handlers in relation to good food handling practices. The fourth was a further microbiological analysis of new samples. The application of a checklist showed that the locations met the requirements of current legislation. Of the 40 samples analyzed, 17.5% (7 samples) were unfit for consumption. Among the unfit samples 15% (6 samples) had coliforms at 45 °C, 2.5% (1 sample) had coagulase-positive staphylococci, 2.5% (1 sample) had Bacillus cereus and 2.5% (1 sample) had Salmonella sp. The results of this study show the importance of controlling the quality of food served to an age group that is prone to health risks.

Simulation and material calibration of ultra high strength steel (UHSS) S960 welded joint under static tensile test utilizing finite element method (FEM)

The aim of this work was to calibrate the material properties including strength and strain values for different material zones of ultra-high strength steel (UHSS) welded joints under monotonic static loading. The UHSS is heat sensitive and softens by heat due to welding, the affected zone is heat affected zone (HAZ). In this regard, cylindrical specimens were cut out from welded joints of Strenx® 960 MC and Strenx® Tube 960 MH, were examined by tensile test. The hardness values of specimens’ cross section were measured. Using correlations between hardness and strength, initial material properties were obtained. The same size specimen with different zones of material same as real specimen were created and defined in finite element method (FEM) software with commercial brand Abaqus 6.14-1. The loading and boundary conditions were defined considering tensile test values. Using initial material properties made of hardness-strength correlations (true stress-strain values) as Abaqus main input, FEM is utilized to simulate the tensile test process. By comparing FEM Abaqus results with measured results of tensile test, initial material properties will be revised and reused as software input to be fully calibrated in such a way that FEM results and tensile test results deviate minimum. Two type of different S960 were used including 960 MC plates, and structural hollow section 960 MH X-joint. The joint is welded by BöhlerTM X96 filler material. In welded joints, typically the following zones appear: Weld (WEL), Heat affected zone (HAZ) coarse grained (HCG) and fine grained (HFG), annealed zone, and base material (BaM). Results showed that: The HAZ zone is softened due to heat input while welding. For all the specimens, the softened zone’s strength is decreased and makes it a weakest zone where fracture happens while loading. Stress concentration of a notched specimen can represent the properties of notched zone. The load-displacement diagram from FEM modeling matches with the experiments by the calibrated material properties by compromising two correlations of hardness and strength.

Bird depredation of grapes in Niagara vineyards : a novel approach to identifying spatial and temporal trends /

Although local grape growers view bird depredation as a significant economic issue, the most recent research on the problem in the Niagara Peninsula is three decades old. Peer-reviewed publications on the subject are rare, and researchers have struggled to develop bird-damage assessment techniques useful for facilitating management programmes. I used a variation of Stevenson and Virgo's (1971) visual estimation procedure to quantify spatial and temporal trends in bird damage to grapes within single vineyard plots at two locations near St. Catharines, Ontario. I present a novel approach to managing the rank-data from visual estimates, which is unprecedented in its sensitivity to spatial trends in bird damage. I also review its valid use in comparative statistical analysis. Spatial trends in 3 out of 4 study plots confirmed a priori predictions about localisation in bird damage based on optimal foraging from a central location (staging area). Damage to grape clusters was: (1) greater near the edges of vineyard plots and decreased with distance towards the center, (2) greater in areas adjacent to staging areas for birds, and (3) vertically stratified, with upper-tier clusters sustaining more damage than lower-tier clusters. From a management perspective, this predictive approach provides vineyard owners with the ability to identify the portions of plots likely to be most susceptible to bird damage, and thus the opportunity to focus deterrent measures in these areas. Other management considerations at Henry of Pelham were: (1) wind damage to ice-wine Riesling and Vidal was much higher than bird damage, (2) plastic netting with narrow mesh provided more effective protection agsiinst birds than nylon netting with wider mesh, and (3) no trends in relative susceptibility of varietals by colour (red vs green) were evident.

Postglacial paleoecology and effects of European settlement on the environment of Lake Hunger and Lake Lisgar, Southwestern Ontario /

This investigation has three purposes I to make a comparative chemical study on sediment cores collected for Lake Lisgar (man-made lake in an urban center) and Lake Hunger (natural basin in a rural community) encompassing the time since European settlement I to determine the postglacial chemical history of Lake Hunger, and to determine the vegetational history of the Lake Hunger area from postglacial time to the present. The minus 80 mesh fraction of 108 soil samples and 18 stream sediment samples collected in the vicinity of Lakes' Lisgar and Hunger were analyzed for cold hydrochloric acid soluble lead, zinc, nickel, cobalt, copper, aluminum, sodium, potassium, calcium, magnesium, iron and manganese. Lacustrine sediments from 5 boreholes in the Lake Lisgar basin were collected. Boreholes 1, 2, 3, and 4 were analyzed for palynological and chemical information and Borehole 5 was subjected to pollen and ostracode analysis. Lacustrine sediments from 6 boreholes in the Lake Hunger basin were collected. Palyno- -logical and chemical analysis were performed on Boreholes 1, 2, 3, 4, and 6 and Borehole 5 was analyzed for pollen. In addition, radiocarbon dates were obtained on sediment samples from Boreholes 4 and 5. A total of 8 surface samples were collected from the margins of the Lake Hunger basin and these were chemically analyzed in the laboratory. All of the lacustrine sediments were ashed and analyzed for cold hydrochloric acid soluble lead, zinc, nickel, cobalt, copper, aluminum, sodium, potassium, calcium, magnesium, iron and manganese using a Perkin Elmer 40) Atomic Absorption spectrophotometer. The results . obtained for the 12 elements were expressed as parts per million in dry sediments. It was found that man's influence on the element distribution patterns in the sediments of Lake Lisgar appeared to be related to his urbanizing developments within the lake vicinity, whereas, the rural developments in the vicinity of lake Hunger appeared to have had little effect on the element distribution patterns in the lake sediments. The distribution patterns of lead, zinc, nickel, cobalt, aluminum, magnesium, sodium and potassium are similar to the % ash curve throughout postglacial time indicating that the rate of erosion in the drainage basin is the main factor which controls the concentration of these elements in the sediments of Lake Hunger. The vegetational history, from palynological analysis, of Lake Hunger from postglacial time to the present includes the following stages: tundra, open spruce forest, closed boreal forest, deciduous forest and the trend towards the re-establishment of pine following the clearing of land and the subsequent settlement of the Lake Hunger area by European settlers. The concentrations of some elements (cobalt, nickel, iron, manganese, calcium, magnesium, sodium and potassium) in the sediments of Lake Hunger appears to be higher during pre-cultural compared to post-cultural times. At least one complete postglacial record of the chemical history within a lake basin is necessary in order to accurately assess man's effects on his environment.

Individual differences in risk-taking and associated characteristics : a test of specificity in executive functions /

Multiple measures have been devised by clinicians and theorists from many different backgrounds for the purpose of assessing the influence of the frontal lobes on behaviour. Some utilize self-report measures to investigate behavioural characteristics such as risktaking, sensation seeking, impulsivity, and sensitivity to reward and punishment in an attempt to understand complex human decision making. Others rely more on neuroimaging and electrophysiological investigation involving experimental tasks thought to demonstrate executive functions in action, while other researchers prefer to study clinical populations with selective damage. Neuropsychological models of frontal lobe functioning have led to a greater appreciation of the dissociations among various aspects of prefrontal cortex function. This thesis involves (1) an examination of various psychometric and experimental indices of executive functions for coherence as one would predict on the basis of highly developed neurophysiological models of prefrontal function, particularly those aspects of executive function that involve predominantly cognitive abilities versus processes characterized by affect regulation; and (2) investigation of the relations between risk-taking, attentional abilties and their associated characteristics using a neurophysiological model of prefrontal functions addressed in (1). Late adolescence is a stage in which the prefrontal cortices undergo intensive structural and functional maturational changes; this period also involves increases in levels of risky and sensation driven behaviours, as well as a hypersensitivity to reward and a reduction in inhibition. Consequently, late adolescence spears to represent an ideal developmental period in which to examine these decision-making behaviours due to the maximum variability of behavioural characteristics of interest. Participants were 45 male undergraduate 18- to 19-year olds, who completed a battery of measures that included self-report, experimental and behavioural measures designed to assess particular aspects of prefrontal and executive functioning. As predicted, factor analysis supported the grouping of executive process by type (either primarily cognitive or affective), conforming to the orbitofrontal versus dorsolateral typology; risk-taking and associated characteristics were associated more with the orbitofrontal than the dorsolateral factor, whereas attentional and planning abilities tended to correlate more strongly with the dorsolateral factor. Results are discussed in light of future assessment, investigation and understanding of complex human decision-making and executive functions. Implications, applications and suggestions for future research are also proposed.

Impact of considering the effects of latent heat on caldera-hosted hydrothermal systems

To investigate the thennal effects of latent heat in hydrothennal settings, an extension was made to the existing finite-element numerical modelling software, Aquarius. The latent heat algorithm was validated using a series of column models, which analysed the effects of penneability (flow rate), thennal gradient, and position along the two-phase curve (pressure). Increasing the flow rate and pressure increases displacement of the liquid-steam boundary from an initial position detennined without accounting for latent heat while increasing the thennal gradient decreases that displacement. Application to a regional scale model of a caldera-hosted hydrothennal system based on a representative suite of calderas (e.g., Yellowstone, Creede, Valles Grande) led to oscillations in the model solution. Oscillations can be reduced or eliminated by mesh refinement, which requires greater computation effort. Results indicate that latent heat should be accounted for to accurately model phase change conditions in hydrothennal settings.