The seasonal evolution of high vertical–mode internal waves in a deep reservoir

The causal mechanism and seasonal evolution of the internal wave field in a deep, warm, monomictic reservoirare examined through the analysis of field observations and numerical techniques. The study period extends fromthe onset of thermal stratification in the spring until midsummer in 2005. During this time, wind forcing wasperiodic, with a period of 24 h (typical of land–sea breezes), and the thermal structure in the lake wascharacterized by the presence of a shallow surface layer overlying a thick metalimnion, typical of small to mediumsized reservoirs with deep outtakes. Basin-scale internal seiches of high vertical mode (ranging from mode V3 toV5) were observed in the metalimnion. The structure of the dominant modes of oscillation changed asstratification evolved on seasonal timescales, but in all cases, their periods were close to that of the local windforcing (i.e., 24 h), suggesting a resonant response. Nonresonant oscillatory modes of type V1 and V2 becamedominant after large frontal events, which disrupted the diurnal periodicity of the wind forcing

Model-based study of a chemical-looping combustion process

Chemical-looping combustion (CLC) is a novel combustion technology with inherent separation of the greenhouse gas CO2. The technique typically employs a dual fluidized bed system where a metal oxide is used as a solid oxygen carrier that transfers the oxygen from combustion air to the fuel. The oxygen carrier is looping between the air reactor, where it is oxidized by the air, and the fuel reactor, where it is reduced by the fuel. Hence, air is not mixed with the fuel, and outgoing CO2 does not become diluted by the nitrogen, which gives a possibility to collect the CO2 from the flue gases after the water vapor is condensed. CLC is being proposed as a promising and energy efficient carbon capture technology, since it can achieve both an increase in power station efficiency simultaneously with low energy penalty from the carbon capture. The outcome of a comprehensive literature study concerning the current status of CLC development is presented in this thesis. Also, a steady state model of the CLC process, based on the conservation equations of mass and energy, was developed. The model was used to determine the process conditions and to calculate the reactor dimensions of a 100 MWth CLC system with bunsenite (NiO) as oxygen carrier and methane (CH4) as fuel. This study has been made in Oxygen Carriers and Their Industrial Applications research project (2008 – 2011), funded by the Tekes – Functional Material program. I would like to acknowledge Tekes and participating companies for funding and all project partners for good and comfortable cooperation.

Developing A Knowledge Management Process Model for Internal IT Organization, Case: Stora Enso Oyj, Corporate IT

The objectives of this Master’s Thesis were to find out what kind of knowledge management strategy would fit best an IT organization that uses ITIL (Information Technology Infrastructure Library) framework for IT Service Management and to create a knowledge management process model to support chosen strategy. The empirical material for this research was collected through qualitative semi-structured interviews of a case organization Stora Enso Corporate IT. The results of the qualitative interviews indicate that codification knowledge management strategy would fit best for the case organization. The knowledge management process model was created based on earlier studies and a literature of knowledge management. The model was evaluated in the interview research and the results showed that the created process model is realistic, useful, and it responds to a real life phenomenon.

A thermogravimetric analysis of the combustion of a Brazilian mineral coal

Knowledge of coal combustion kinetics is crucial for burner design. This work aims to contribute on this issue by determining the kinetics of a particular Brazilian bituminous coal. Non-isothermal thermogravimetry was applied for determining both the pre-exponential factor and the activation energy. Coal samples of 10 mg and 775 mm mean size were used in synthetic air atmospheres (21 % O2). Heating rates from 10 to 50 ºC/min were applied until the temperature reached 850 ºC, which was kept constant until burnout. The activation energy for the primary and the secondary combustion resulted, respectively, in 135.1 kJ/mol and 85.1 kJ/mol.

El juego y su estructura interna en relación con el trabajo de la condición física en primaria = Games and their internal structure in relation to the work of physical condition in Primary Education

One of the methodological resources that teachers use in a generalised way in Physical Education classes is the game. Inthis article we define the concept of game and analyse the characteristics of their internal structure. On the other hand welook at the concepts of physical condition and conditional skills and describe the objectives of its work in Primary Education.Finally, we relate these concepts and propose two practical examples of modifying the internal structure of the game so asto produce variations in the implied conditional skills

Modelagem da combustão da dinitramida de amônio por simulação computacional

In this work, the combustion process of ammonium dinitramide, ADN, has been modeled in two different situations: decomposition in open environment, with abundant air and decomposition in a rocket motor internal environmental conditions. The profiles of the two processes were achieved, based on molar fractions of the species that compose the products of ADN combustion. The velocity of formation and quantity of species in the open environment was bigger than the ones in the rocket motor environment, showing the effect of the different atmosphere in the reactions kinetics.

Internal standard versus external standard calibration: an uncertainty case study of a liquid chromatography analysis

Traditionally, in the cigarettes industry, the determination of ammonium ion in the mainstream smoke is performed by ion chromatography. This work studies this determination and compares the results of this technique with the use of external and internal standard calibration. A reference cigarette sample presented measurement uncertainty of 2.0 μg/cigarette and 1.5 μg/cigarette, with external and internal standard, respectively. It is observed that the greatest source of uncertainty is the bias correction factor and that it is even more significant when using external standard, confirming thus the importance of internal standardization for this correction.

Diesel/biodiesel soot oxidation with ceo2 and ceo2-zro2-modified cordierites: a facile way of accounting for their catalytic ability in fuel combustion processes

CeO2 and mixed CeO2-ZrO2 nanopowders were synthesized and efficiently deposited onto cordierite substrates, with the evaluation of their morphologic and structural properties through XRD, SEM, and FTIR. The modified substrates were employed as outer heterogeneous catalysts for reducing the soot originated from the diesel and diesel/biodiesel blends incomplete combustion. Their activity was evaluated in a diesel stationary motor, and a comparative analysis of the soot emission was carried out through diffuse reflectance spectroscopy. The analyses have shown that the catalyst-impregnated cordierite samples are very efficient for soot oxidation, being capable of reducing the soot emission in more than 60%.

Palladium-supported catalysts in methane combustion: comparison of alumina and zirconia supports

Palladium catalysts supported on alumina and zirconia were prepared by the impregnation method and calcined at 600 and 1000 ºC. Catalysts were characterized by BET measurements, XRD, XPS, O2-TPD and tested in methane combustion through temperature programmed surface reaction. Alumina supported catalysts were slightly more active than zirconia supported catalysts, but after initial heat treatment at 1000 ºC, zirconia supported palladium catalyst showed better performance above 500 ºC A pattern between temperature interval stability of PdOx species and activity was observed, where better PdOx stability was associated with more active catalysts.

Methane combustion kinetic rate constants determination: an ill-posed inverse problem analysis

Methane combustion was studied by the Westbrook and Dryer model. This well-established simplified mechanism is very useful in combustion science, for computational effort can be notably reduced. In the inversion procedure to be studied, rate constants are obtained from [CO] concentration data. However, when inherent experimental errors in chemical concentrations are considered, an ill-conditioned inverse problem must be solved for which appropriate mathematical algorithms are needed. A recurrent neural network was chosen due to its numerical stability and robustness. The proposed methodology was compared against Simplex and Levenberg-Marquardt, the most used methods for optimization problems.

Influence of internal seedborne Fusarium semitectum on cotton seedlings

Fusarium semitectum was found to be the major seed colonizing fungus in the commercial acid delinted cotton (Gossypium hirsutum) seed lots. There was no correlation, however, between its incidence and seedling emergence and disease symptoms on the emerged seedlings in autoclaved sand. Inoculation technique simulating internally seedborne nature of the fungus showed that the observed non-correlation might be related to the threshold level of seed coat colonization. The internally seedborne inoculum besides reducing seedling emergence, incited an array of symptoms on the emerged seedlings, which ranged from negative geotropism, leaf tearing, collar rot leading to dry root rot and seedling mortality. The dry root rot continued to develop on the plants surviving the seedling phase. The collar rot symptoms can be confused with those caused by Rhizoctonia solani.

Voimalaitoksen palamisilman esilämmittimen sisäpuolisen korroosion hallinta pinta-aktiivisten amiinien avulla

Useat voimalaitokset käyttävät hiiliteräksistä valmistettuja palamisilman esilämmittimiä, joissa höyrykattilan palamisilmaa lämmitetään matalapainehöyryllä. Joissakin tapauksissa esilämmittimet ovat kärsineet sisäpuolisen korroosion aiheuttamista putkirikoista. Tämän työn tavoitteena oli selvittää korroosiovaurioiden aiheuttajat ja tarkastella eri keinoja uusien korroosiovaurioiden ehkäisemiseksi. Keskeisimpänä uusien vaurioiden ehkäisykeinona tarkastellaan pinta-aktiivisia amiineja sisältäviä höyrykattilan jälkiannostelukemikaaliseoksia, joista tarkemman tarkastelun kohteena on kaupallinen Helamin 90 H Turb- kemikaaliseos. Pääasialliseksi korroosion aiheuttajaksi on usein epäilty höyryn sisältämää hiilidioksidia. Uusimpien näkemysten mukaan orgaaniset hapot, pääasiassa etikka- ja muurahaishappo ovat kuitenkin hiilidioksidia voimakkaampia korroosion aiheuttajia ilmanesilämmittimissä. Orgaaniset hapot väkevöityvät höyryn lauhtumisen alkaessa muodostuviin lauhdepisaroihin ja alentavat pH-tasoa radikaalisti. pH-tason aleneminen nopeuttaa metallipintoja suojaavan magnetiitin liukenemista ja vaikeuttaa myös sen uusiutumista. Orgaanisia happoja ja hiilidioksidia muodostuu orgaanisten aineiden osittaisessa hajoamisessa höyrykattilan vesi-höyrypiirissä. Pääasialliset orgaanisten aineiden lähteet ovat lisäveden mukana kattilaan kulkeutuva luonnon orgaaninen aines ja käytetyt orgaaniset jälkiannostelukemikaalit. Orgaanisten aineiden kuormaa voidaan pienentää parantamalla lisäveden valmistusprosessin orgaanisten aineiden erotustehokkuutta esimerkiksi käänteisosmoosilla. Mikäli lisäveden laadun parantaminen ei ole järkevästi toteutettavissa, voidaan orgaanisten jälkiannostelukemikaalien oikeanlaisella käytöllä neutraloida orgaanisten happojen vaikutus ilmanesilämmittimissä. Tehokkaimmaksi korroosion hillitsijäksi suoritettujen mittausten perusteella osoittautuivat kemikaaliseokset, jotka sisältävät alkaloivien amiinien lisäksi kalvoa muodostavaa pinta-aktiivista amiinia.

Influence of mixed fuels combustion on boiler operation

The aim of this work is to study the effect of different fuel mixtures on the operation of circulating fluidized bed (CFB) boiler. The applicability of heat balance modeling software IPSEpro to simulate CFB boiler operation is also investigated. The work discusses various types of boilers and methods of boiler operation. The fuel properties and the possible fuel influence on the boiler efficiency are described. Various biofuel types that are possible to use in combination with other fuels are presented. Some examples of the fuel mixtures use are given. A CFB boiler model has been constructed using IPSEpro and applied to analyze boiler operation outside design conditions. In the simulations, the effect of different load levels and moisture contents for the fuel mixture has been studied.

Evaluation of the dioxin and furan formation thermodynamics in combustion processes of urban solid wastes

Specific combustion programs (Gaseq, Chemical equilibria in perfect gases, Chris Morley) are used to model dioxin and formation in the incineration processes of urban solid wastes. Thanks to these programs, it is possible to establish correlations with the formation mechanisms postulated in literature on the subject. It was found that minimum oxygen quantities are required to obtain a significant formation of these compounds and that more furans than dioxins are formed. Likewise, dioxin and furan formation is related to the presence of carbon monoxide, and dioxin and furan distribution among its different compounds depends on the chlorine and hydrogen relative composition. This is due to the fact that an increased chlorine availability leads to the formation of compounds bearing a higher chlorine concentration (penta-, hexa-, hepta-, and octachlorides), whereas an increased hydrogen availability leads to the formation of compounds bearing a lower chlorine number (mono, di-, tri-, and tetrachlorides).

Model based study of a calcium oxide looping process for post-combustion carbon dioxide capture

Calcium oxide looping is a carbon dioxide sequestration technique that utilizes the partially reversible reaction between limestone and carbon dioxide in two interconnected fluidised beds, carbonator and calciner. Flue gases from a combustor are fed into the carbonator where calcium oxide reacts with carbon dioxide within the gases at a temperature of 650 ºC. Calcium oxide is transformed into calcium carbonate which is circulated into the regenerative calciner, where calcium carbonate is returned into calcium oxide and a stream of pure carbon dioxide at a higher temperature of 950 ºC. Calcium oxide looping has proved to have a low impact on the overall process efficiency and would be easily retrofitted into existing power plants. This master’s thesis is done in participation to an EU funded project CaOling as a part of the Lappeenranta University of Technology deliverable, reactor modelling and scale-up tools. Thesis concentrates in creating the first model frame and finding the physically relevant phenomena governing the process.