Cascaded DC-DC converter connection of photovoltaic modules

New residential scale photovoltaic (PV) arrays are commonly connected to the grid by a single dc-ac inverter connected to a series string of pv panels, or many small dc-ac inverters which connect one or two panels directly to the ac grid. This paper proposes an alternative topology of nonisolated per-panel dc-dc converters connected in series to create a high voltage string connected to a simplified dc-ac inverter. This offers the advantages of a "converter-per-panel" approach without the cost or efficiency penalties of individual dc-ac grid connected inverters. Buck, boost, buck-boost, and Cu´k converters are considered as possible dc-dc converters that can be cascaded. Matlab simulations are used to compare the efficiency of each topology as well as evaluating the benefits of increasing cost and complexity. The buck and then boost converters are shown to be the most efficient topologies for a given cost, with the buck best suited for long strings and the boost for short strings. While flexible in voltage ranges, buck-boost, and Cu´k converters are always at an efficiency or alternatively cost disadvantage.

A class B switch-mode assisted linear amplifier

A switch-mode assisted linear amplifier (SMALA) combining a linear (Class B) and a switch-mode (Class D) amplifier is presented. The usual single hysteretic controlled half-bridge current dumping stage is replaced by two parallel buck converter stages, in a parallel voltage controlled topology. These operate independently: one buck converter sources current to assist the upper Class B output device, and a complementary converter sinks current to assist the lower device. This topology lends itself to a novel control approach of a dead-band at low power levels where neither class D amplifier assists, allowing the class B amplifier to supply the load without interference, ensuring high fidelity. A 20 W implementation demonstrates 85% efficiency, with distortion below 0.08% measured across the full audio bandwidth at 15 W. The class D amplifier begins assisting at 2 W, and below this value, the distortion was below 0.03%. Complete circuitry is given, showing the simplicity of the additional class D amplifier and its corresponding control circuitry.

Digitally-implemented naturally sampled PWM suitable for multilevel converter control

For dynamic closed loop control of a multilevel converter with a low pulse number (ratio of switching frequency to synthesized fundamental), natural sampled pulse-width modulation (PWM) is the best form of modulation. Natural sampling does not introduce distortion or a delayed response to the modulating signal. However previous natural sampled PWM implementations have generally been analog. For a modular multilevel converter, a digital implementation has advantages of accuracy and flexibility. Re-sampled uniform PWM is a novel digital modulation technique which approaches the performance of natural PWM. Both hardware and software implementations for a five level multilevel converter phase are presented, demonstrating the improvement over uniform PWM.

Detecting anomalous events at railway level crossings

Collisions between pedestrians and vehicles continue to be a major problem throughout the world. Pedestrians trying to cross roads and railway tracks without any caution are often highly susceptible to collisions with vehicles and trains. Continuous financial, human and other losses have prompted transport related organizations to come up with various solutions addressing this issue. However, the quest for new and significant improvements in this area is still ongoing. This work addresses this issue by building a general framework using computer vision techniques to automatically monitor pedestrian movements in such high-risk areas to enable better analysis of activity, and the creation of future alerting strategies. As a result of rapid development in the electronics and semi-conductor industry there is extensive deployment of CCTV cameras in public places to capture video footage. This footage can then be used to analyse crowd activities in those particular places. This work seeks to identify the abnormal behaviour of individuals in video footage. In this work we propose using a Semi-2D Hidden Markov Model (HMM), Full-2D HMM and Spatial HMM to model the normal activities of people. The outliers of the model (i.e. those observations with insufficient likelihood) are identified as abnormal activities. Location features, flow features and optical flow textures are used as the features for the model. The proposed approaches are evaluated using the publicly available UCSD datasets, and we demonstrate improved performance using a Semi-2D Hidden Markov Model compared to other state of the art methods. Further we illustrate how our proposed methods can be applied to detect anomalous events at rail level crossings.

High frequency high power converters for industrial applications

The main contribution of this project was to investigate power electronics technology in designing and developing high frequency high power converters for industrial applications. Therefore, the research was conducted at two levels; first at system level which mainly encapsulated the circuit topology and control scheme and second at application level which involves with real-world applications. Pursuing these objectives, varied topologies have been developed and proposed within this research. The main aim was to resolving solid-state switches limited power rating and operating speed while increasing the system flexibility considering the application characteristics. The developed new power converter configurations were applied to pulsed power and high power ultrasound applications for experimental validation.

Designing innovative business models: Five emerging meta-models

Business models to date have remained the creation of management, however, it is the belief of the authors that designers should be critically approaching, challenging and creating new business models as part of their practice. This belief portrays a new era where business model constructs become the new design brief of the future and fuel design and innovation to work together at the strategic level of an organisation. Innovation can no longer rely on technology and R&D alone but must incorporate business models. Business model innovation has become a strong type of competitive advantage. As firms choose not to compete only on price, but through the delivery of a unique value proposition in order to engage with customers and to differentiate a company within a competitive market. The purpose of this paper is to explore and investigate business model design through various product and/or service deliveries, and identify common drivers that are catalysts for business model innovation. Fifty companies spanning a diverse range of criteria were chosen, to evaluate and compare commonalities and differences in the design of their business models. The analysis of these business cases uncovered commonalities of the key strategic drivers behind these innovative business models. Five Meta Models were derived from this content analysis: Customer Led, Cost Driven, Resource Led, Partnership Led and Price Led. These five key foci provide a designer with a focus from which quick prototypes of new business models are created. Implications from this research suggest there is no ‘one right’ model, but rather through experimentation, the generation of many unique and diverse concepts can result in greater possibilities for future innovation and sustained competitive advantage.

Vision-based estimation of airborne target pseudobearing rate using hidden Markov model filters

The problem of estimating pseudobearing rate information of an airborne target based on measurements from a vision sensor is considered. Novel image speed and heading angle estimators are presented that exploit image morphology, hidden Markov model (HMM) filtering, and relative entropy rate (RER) concepts to allow pseudobearing rate information to be determined before (or whilst) the target track is being estimated from vision information.

Theoretical and experimental characterisation of energy in an electrostatic discharge

Electrostatic discharges have been identified as the most likely cause in a number of incidents of fire and explosion with unexplained ignitions. The lack of data and suitable models for this ignition mechanism creates a void in the analysis to quantify the importance of static electricity as a credible ignition mechanism. Quantifiable hazard analysis of the risk of ignition by static discharge cannot, therefore, be entirely carried out with our current understanding of this phenomenon. The study of electrostatics has been ongoing for a long time. However, it was not until the wide spread use of electronics that research was developed for the protection of electronics from electrostatic discharges. Current experimental models for electrostatic discharge developed for intrinsic safety with electronics are inadequate for ignition analysis and typically are not supported by theoretical analysis. A preliminary simulation and experiment with low voltage was designed to investigate the characteristics of energy dissipation and provided a basis for a high voltage investigation. It was seen that for a low voltage the discharge energy represents about 10% of the initial capacitive energy available and that the energy dissipation was within 10 ns of the initial discharge. The potential difference is greatest at the initial break down when the largest amount of the energy is dissipated. The discharge pathway is then established and minimal energy is dissipated as energy dissipation becomes greatly influenced by other components and stray resistance in the discharge circuit. From the initial low voltage simulation work, the importance of the energy dissipation and the characteristic of the discharge were determined. After the preliminary low voltage work was completed, a high voltage discharge experiment was designed and fabricated. Voltage and current measurement were recorded on the discharge circuit allowing the discharge characteristic to be recorded and energy dissipation in the discharge circuit calculated. Discharge energy calculations show consistency with the low voltage work relating to discharge energy with about 30-40% of the total initial capacitive energy being discharged in the resulting high voltage arc. After the system was characterised and operation validated, high voltage ignition energy measurements were conducted on a solution of n-Pentane evaporating in a 250 cm3 chamber. A series of ignition experiments were conducted to determine the minimum ignition energy of n-Pentane. The data from the ignition work was analysed with standard statistical regression methods for tests that return binary (yes/no) data and found to be in agreement with recent publications. The research demonstrates that energy dissipation is heavily dependent on the circuit configuration and most especially by the discharge circuit's capacitance and resistance. The analysis established a discharge profile for the discharges studied and validates the application of this methodology for further research into different materials and atmospheres; by systematically looking at discharge profiles of test materials with various parameters (e.g., capacitance, inductance, and resistance). Systematic experiments looking at the discharge characteristics of the spark will also help understand the way energy is dissipated in an electrostatic discharge enabling a better understanding of the ignition characteristics of materials in terms of energy and the dissipation of that energy in an electrostatic discharge.

Early challenges of shifting an Australian manufacturer’s utilisation of design

This paper presents the findings from the initial exploration phase of an 11 month project, identifying the early challenges that a design innovation catalyst faces while initiating a shift in the way a medium sized manufacturing firm utilises design. Ultimately, the overarching aims of the project are to transform the utilisation of design within the participating company from a styling tool to a strategic process through the implementation of a design led approach to innovation. Insights were found through qualitative interviews with company staff and reflective journal entries as part of an Action Research methodology. Challenges identified include managing expectations, conveying the potential of a design innovation catalyst and a design led approach to innovation, and a siloed and risk averse culture. Findings presented in this paper will assist in identifying and understanding the preliminary challenges encountered by a design innovation catalyst when embarking on a design led transformation. Future innovation catalysts can prepare for possible barriers by highlighting considerations, opportunities and challenges when embarking on a design led transformation. Implications of this research are provided as possible approaches to overcoming these challenges.

Can emotion provide a new approach to business model innovation?

Companies require new strategies to drive growth and survival, as the fast pace of change has created the need for greater business flexibility. Therefore, industry leaders are looking to business innovation as a principle source of differentiation and competitive advantage. However, most companies rely heavily on either technology or products to provide business innovation, yet competitors can easily and rapidly surpass these forms of innovation. Business model innovation expands beyond innovation in isolated areas, such as product innovation, to create strategies that incorporate many business avenues to work together to create and deliver value to its customers. Existing literature highlights that a business model’s central role is ‘customer value’. However, the emotional underpinnings of customer value within a business model are not well understood. The integration of customer emotion into business model design and value chain can be viewed as a way to innovate beyond just products, services and processes. This paper investigates the emotional avenues within business strategy and operations, business model innovation and customer engagement. Three propositions are outlined and explored as future research. The significance of this research is to provide companies with a new approach to innovation through a deeper understanding and integration of their customers’ emotions.

From production to purpose : using design led innovation to Build Strategic Potential in a Family-Owned SME

There is an evident need to develop the strategic capabilities of companies from within, to ensure competitive competence in a time where strategy is a necessity. This paper is based on the first 4 months of a longitudinal embedded case study of a family-owned Australian small to medium enterprise, in their journey towards design integration. The first author was embedded as a ‘Design Innovation Catalyst’ to collaborate on overcoming early barriers of strategic development, using design led innovation. Action research methodology, semi-structured interviews with seven out of eight employees and a reflective journal revealed the absence of a shared vision, conflicting drivers and a focus on operational efficiency rather than strategy. Through the Catalyst’s facilitation, a company vision, general awareness, practice and knowledge in strategic development have emerged as the first steps to generating strategic design competence within the firm.

The challenges of adopting design-led innovative strategies in not for profits : the role of consumers, culture and employees

Major changes to regulations, funding and consumer demand in the Australian aged care industry are driving not for profits in this sector to reshape and rethink the services they offer and the ways in which they deliver their services to consumers. Many not for profit organisations facing these new challenges are also facing organisational cultural barriers in the development and implementation of innovative strategies. This paper presents a case study where one organisation, using design led innovation, explored consumer insights and employee values to find new ways to facilitate change.

Design led innovation : shifting from smart follower to digital strategy leader in the Australian airport sector

This paper presents and discusses organisational barriers and opportunities arising from the dissemination of design led innovation within a leading Australian airport corporation. This research is part of a greater action research program which aims to integrate design as a strategic capability through design led innovation within Australian businesses. Findings reveal that there is an opportunity to employ the theoretical framework and tools of design led innovation in practice to build collaborative idea generation by involving customers and stakeholders within the proposal of new to world propositions. The iterative gathering of deep customer insights also provided an opportunity to leverage a greater understanding of stakeholders and customers in strengthening continuing business partnerships through co-design. Challenges to the design led approach include resistance to the exploratory nature of gathering deep customer insights, the testing of long held assumptions and market data, and the disruption of an organisational mindset geared toward risk aversion instilled within the aviation industry. The implication from these findings is that design led innovation can provide the critical platform to allow for a business to grow and sustain internal design capabilities necessary to challenge prevailing assumptions about how its business model operates to deliver value to customers and stakeholders alike. The platform of design led innovation also provides an avenue to support a cultural transformation towards anticipating future needs necessary for establishing a position of leadership within the broader economic environment.

Photovoltaic DC-DC module integrated converter for novel cascaded and bypass grid connection topologies - design and optimisation

Grid connected photovoltaic (PV) inverters fall into three broad categories - central, string and module integrated converters (MICs). MICs offer many advantages in performance and flexibility, but are at a cost disadvantage. Two alternative novel approaches proposed by the author - cascaded dc-dc MICs and bypass dc-dc MICs - integrate a simple non-isolated intelligent dc-dc converter with each PV module to provide the advantages of dc-ac MICs at a lower cost. A suitable universal 150 W 5 A dc-dc converter design is presented based on two interleaved MOSFET half bridges. Testing shows zero voltage switching (ZVS) keeps losses under 1 W for bi-directional power flows up to 15 W between two adjacent 12 V PV modules for the bypass application, and efficiencies over 94% for most of the operational power range for the cascaded converter application. Based on the experimental results, potential optimizations to further reduce losses are discussed.

Selection of energy storage system for a regenerative dynamic dynamometer

This paper presents a design technique of a fully regenerative dynamic dynamometer. It incorporates an energy storage system to absorb the energy variation due to dynamometer transients. This allows the minimum power electronics requirement at the grid to supply the losses. The simulation results of the full system over a driving cycle show the amount of energy required to complete a driving cycle, therefore the size of the energy storage system can be determined.