Phyllochron estimation in intercropped strawberry and monocrop systems in a protected environment

The phyllochron is defined as the time required for the appearance of successive leaves on a plant; this characterises plant growth, development and adaptation to the environment. To check the growth and adaptation in cultivars of strawberry grown intercropped with fig trees, it was estimated the phyllochron in these production systems and in the monocrop. The experiment was conducted in greenhouses at the University of Passo Fundo (28º15'41'' S, 52º24'45'' W and 709 m) from June 8th to September 4th, 2009; this comprised the period of transplant until the 2nd flowering. The cultivars Aromas, Camino Real, Albion, Camarosa and Ventana, which seedlings were originated from the Agrícola LLahuen Nursery in Chile, as well as Festival, Camino Real and Earlibrite, originated from the Viansa S.A. Nursery in Argentina, were grown in white polyethylene bags filled with commercial substrate (Tecnomax®) and evaluated. The treatments were arranged in a randomised block design and four replicates were performed. A linear regression was realized between the leaf number (LN) in the main crown and the accumulated thermal time (ATT). The phyllochron (degree-day leaf-1) was estimated as the inverse of the angular coefficient of the linear regression. The data were submitted to ANOVA, and when significance was observed, the means were compared using the Tukey test (p < 0.05). The mean and standard deviation of phyllochrons of strawberry cultivars intercropped with fig trees varied from 149.35ºC day leaf-1 ± 31.29 in the Albion cultivar to 86.34ºC day leaf-1 ± 34.74 in the Ventana cultivar. Significant differences were observed among cultivars produced in a soilless environment with higher values recorded for Albion (199.96ºC day leaf-1 ± 29.7), which required more degree-days to produce a leaf, while cv. Ventana (85.76ºC day leaf-1 ± 11.51) exhibited a lower phyllochron mean value. Based on these results, Albion requires more degree-days to issue a leaf as compared to cv. Ventana. It was conclude that strawberry cultivars can be grown intercropped with fig trees (cv. Roxo de Valinhos).

Compliance management is becoming a major issue in IS design

This article aims at improving the information systems management support to Risk and Compliance Management process, i.e. the management of all compliance imperatives that impact an organization, including both legal and stra- tegically self-imposed imperatives. We propose a process to achieve such regula- tory compliance by aligning the Governance activities with the Risk Management ones, and we suggest Compliance should be considered as a requirement for the Risk Management platform. We will propose a framework to align law and IT compliance requirements and we will use it to underline possible directions of investigation resumed in our discussion section. This work is based on an exten- sive review of the existing literature and on the results of a four-month internship done within the IT compliance team of a major financial institution in Switzer- land, which has legal entities situated in different countries.

Application Architecture Design for an Industrial Service Company

Työssä oli tavoitteena suunnitella globaali sovellusarkkitehtuuri, joka ohjaa teollisen huoltoyrityksen sovellusten kehitystyötä. Sovellusarkkitehtuuri kuvaa tietokoneohjelmien toiminnallisuuteen loppukäyttäjien näkökulmasta ja sen laatiminen on osa strategista tietojärjestelmäsuunnittelua. Arkkitehtuurin tehtävänä on varmistaa, että tietojärjestelmät suunnitellaan kokonaisuutena tukemaan organisaation toimintaa. Arkkitehtuurin tekemistä ohjasi strategisen tietojärjestelmäsuunnittelun periatteet ja mallit. Tekniikat olivat samoja kuin projektikohtaisessa tietojärjestelmäsuunnittelussa. Sovellusarkkitehtuurin tekeminen alkoi tutustumalla yrityksessä vallitsevaan tilanteeseen sekä liiketoiminta- ja tietotekniikkastrategioihin. Tarkastelun kohteena olivat pääasiassa liiketoimintaprosessit ja käytössä olevat sovellukset. Tutustuminen tapahtui lähinnä haastatteluin ja dokumentteihin tutustumalla. Seuraavaksi johdettiin vaatimukset tulevaisuuden sovelluksille haastatteluista ja edellisen vaiheen materiaalin perusteella. Liiketoiminnan kannalta tärkeimmät vaatimukset valittiin täytettäväksi arkkitehtuurilla. Varsinaisen arkitehtuurin tekeminen oli lähinnä sovellusten valitsemisesta ja niiden keskinäisten suhteiden määrittelyä. Arkkitehtuurin perusteella määritettiin kehityshankeet.

Robots and robotic systems for the electronics and telecommunication industry

Tämä diplomityö tutkii elektroniikka- ja telekommunikaatioteollisuutta sekä siihen läheisesti liittyviä robotteja ja robottijärjestelmiä. Tavoitteena on määrittää E&T-teollisuuden prosesseihin soveltuvien robottien testausmenetelmä. Tavoitteena on myös selvittää kahden ABB:n robotin soveltuvuutta E&T-teollisuuden tarpeisiin. Muutamia systemaattisia valmistusjärjestelmien suunnitteluun soveltuvia menetelmiä ja apuvälineitä on myös käsitelty. Alussa työ keskittyy elektroniikka- ja telekommunikaatioteollisuuden nykytilan tutkimiseen sekä siellä vallitsevien ja ennustettujen trendien kartoitukseen. Kohdat “Collaborative manufacturing” ja E&T-teollisuuden valmistusjärjestelmille asettamat vaatimukset käydään yksityiskohtaisesti läpi. Tutkimuksen pääkohteina ovat robotit, erityisesti ABB:n IRB 140 ja IRB 340 sekä robottien testausmenetelmän määrittäminen. Työssä käydään läpi IRB 340:llä suoritetut testit, jotka tehtiin sekä konenäköjärjestelmää apuna käyttäen että ilman. Myös TTKK:lla suoritetut robottitestit on käyty läpi. Robottien testituloksia on analysoitu ja vertailtu muihin robotteihin. Testausmenetelmät perustuvat ISO 9283 standardiin. Viimeinen osa työstä esittelee robottijärjestelmien systemaattiseen suunnitteluun soveltuvia menetelmiä ja apuvälineitä. Esillä ovat mm. Modular function deployment (MFD) ja The system design method (SDM).

Software Security Design and Testing

Elektroninen kaupankäynti ja pankkipalvelut ovat herättäneet toiminnan jatkuvuuden kannalta erittäin kriittisen kysymyksen siitä, kuinka näitä palveluja pystytään suojaamaan järjestäytynyttä rikollisuutta ja erilaisia hyväksikäyttöjä vastaan.

Design of User Authentication System for Multi-operator wireless LANs

Langattomat lähiverkot ovat viime vuosikymmeninä saavuttaneet suuren suosion. Tässä työssä käsitellään käyttäjien todentamisjärjestelmän suunnittelua ja kehitystä langattomaan monioperaattoriverkkoon. Langattomassa monioperaattoriverkossa käyttäjillä on mahdollisuus käyttää eri operaattoreiden palveluita. Aluksi käsitellään olemassa olevia todentamismenetelmiä ja -järjestelmiä. minkä jälkeen kuvaillaan todentamisjärjestelmä langattomille monioperaattoriverkoille. Todentamisjärjestelmän ratkaisuvaihtoehtoja esitellään kaksi, niin sanotut moni- istunto - ja yksittäisistuntomalli. Moni-istuntomalli on normaali lähestymistapa käyttäjien todentamiseen tietokonejärjestelmissä. Siinä käyttäjän pitää tunnistautua ja todentaa itsensä jokaiselle verkon palvelulle erikseen. Yksittäisistuntomallissa pyritään parempaan luotettavuuteen ja käytettävyyteen. Siinä käyttäjä todentaa itsensä vain kerran ja voi sen jälkeen päästä useisiin palveluihin. Työn loppuosassa kuvaillaan suunnitellun järjestelmän toteutusta. Lisäksi ehdotetaan vaihtoehtoisia toteutustapoja, analysoidaan järjestelmän heikkouksia ja kerrotaan jatkokehitysmahdoillisuuksista.

Design and Testing of Database Libraries

Nokia Push To Talk järjestelmä tarjoaa uuden kommunikointimetodin tavallisen puhelun oheen. Yksi tärkeimmistä uuden järjestelmän ominaisuuksista on puhelunmuodostuksen nopeus. Lisäksi järjestelmän tulee olla telekommunikaatiojärjestelmien yleisten periaatteiden mukainen, mahdollisimman stabiili ja skaalautuva, jotta järjestelmä olisi mahdollisimman vikasietoinen ja laajennettavissa. Diplomityön päätavoite on esitellä "C++"-tietokantakirjastojen suunnittelua ja testausta. Aluksi tutkitaan tietokantajärjestelmien problematiikkaa alkaen tietokantajärjestelmän valinnasta ja huomioiden erityisesti nopeuskriteerit. Sitten esitellään kaksi teknistä toteutusta kahta "C++"-tietokantakirjastoa varten ja pohditaan joitakin vaihtoehtoisia toteutustapoja.

Development of support and drive systems for defiberization drum

Diplomityön tarkoituksena oli kuidutusrumpulaitteiston käytön- ja kannatuksen kehittä-minen. Työ rajattiin laajuutensa vuoksi koskemaan tuotesarjan viittä pienintä kokoa. Työn alkuosassa käsitellään kuidutuksen teoriaa ja siihen soveltuvia laitteistoja. Käytön suunnittelun kannalta olennaista käynnistystehon tarvetta on tarkasteltu lähtökohdaisesti fysiikan avulla. Perustietoja teorialle on haettu aiemmista tutkimuksista sekä kirjallisuu-desta. Tarkastelun tuloksena teoriaa on kehitty ja se on saatu vastaamaan todellisuutta aiempaa paremmin. Kannatuksen ja käytön toteuttamisvaihtoja etsittäessä on käytetty systemaattisen koneen-suunnittelun keinoja. Saatuja ideoita on arvioitu teknillis-taloudellisin perustein ja näistä on valittu parhaat vaihtoehdot jatkokehitykseen. Jatkokehitysvaiheessa ratkaisuvaihto-ehtoja on tarkasteltu komponenttitasolla ja näistä on tehty yksityiskohtaiset kustannus-laskelmat. Työn tuloksena on esitetty kannatuksen ja käytön toteutusvaihtoehto, jonka avulla voidaan saavuttaa merkittäviä kustannussäästöjä. Korkea, 30 prosentin kustannussäästö-tavoite saavutettiin.

Toward a rational design of combination therapy in cancer.

By merging computational systems modeling and experimental approaches, we have uncovered treatments reprogramming pro-angiogenic monocytes present in breast tumor into immunologically potent cells capable of mediating an anti-tumor immune response. The unraveled pathways and ligands which underlie monocyte pro-angiogenic activity have a strong predictive value for breast cancer patient relapse - free survival.

Effect of dripline flushing on subsurface drip irrigation systems

The velocity of dripline flushing in subsurface drip irrigation (SDI) systems affects system design, cost, management, performance, and longevity. A 30‐day field study was conducted at Kansas State University to analyze the effect of four targeted flushing velocities (0.23, 0.30, 0.46, and 0.61 m/s) for a fixed 15 min duration of flushing and three flushing frequencies (no flushing or flushing every 15 or 30 days) on SDI emitter discharge and sediments within the dripline and removed in the flushing water. At the end of the field experiment (371 h), the amount of solids carried away by the flushing water and retained in every lateral were determined as well as laboratory determination of emitter discharge for every single emitter within each dripline. Greater dripline flushing velocities, which also resulted in greater flushing volumes, tended to result in greater amounts of solids in the flushing water, but the differences were not always statistically significant. Neither the frequency of flushing nor the interaction of flushing frequency and velocity significantly affected the amount of solids in the flushing water. There was a greater concentration of solids in the beginning one‐third of the 90 m laterals, particularly for treatments with no flushing or with slower dripline flushing velocities. As flushing velocity and concurrently flushing volume increased, there was a tendency for greater solids removal and/or more equal distribution within the dripline. At the end of the field study, the average emitter discharge as measured in the laboratory for a total of 3970 emitters was 0.64 L/h. which was significantly less (approximately 2.5%) than the discharge for new and unused emitters. Only six emitters were nearly or fully clogged, with discharges between 0% and 5% of new and unused emitters. Flushing velocity and flushing frequency did not have consistent significant effects on emitter discharge, and those numerical differences that did exist were small (<3%). Emitter discharge was approximately 3% less for the distal ends of the driplines (last 20% of the dripline). Although not a specific factor in the study, the results of solids removals during flushing and solids retention within the different dripline sections suggest that duration of flushing may be a more cost‐effective management option than increasing the dripline flushing velocity through SDI system design. Finally, although microirrigation system components have been improved over the years, the need for flushing to remove solids and reduce clogging potential has not been eliminated

A Co-Processor Approach for Efficient Java Execution in Embedded Systems

This thesis deals with a hardware accelerated Java virtual machine, named REALJava. The REALJava virtual machine is targeted for resource constrained embedded systems. The goal is to attain increased computational performance with reduced power consumption. While these objectives are often seen as trade-offs, in this context both of them can be attained simultaneously by using dedicated hardware. The target level of the computational performance of the REALJava virtual machine is initially set to be as fast as the currently available full custom ASIC Java processors. As a secondary goal all of the components of the virtual machine are designed so that the resulting system can be scaled to support multiple co-processor cores. The virtual machine is designed using the hardware/software co-design paradigm. The partitioning between the two domains is flexible, allowing customizations to the resulting system, for instance the floating point support can be omitted from the hardware in order to decrease the size of the co-processor core. The communication between the hardware and the software domains is encapsulated into modules. This allows the REALJava virtual machine to be easily integrated into any system, simply by redesigning the communication modules. Besides the virtual machine and the related co-processor architecture, several performance enhancing techniques are presented. These include techniques related to instruction folding, stack handling, method invocation, constant loading and control in time domain. The REALJava virtual machine is prototyped using three different FPGA platforms. The original pipeline structure is modified to suit the FPGA environment. The performance of the resulting Java virtual machine is evaluated against existing Java solutions in the embedded systems field. The results show that the goals are attained, both in terms of computational performance and power consumption. Especially the computational performance is evaluated thoroughly, and the results show that the REALJava is more than twice as fast as the fastest full custom ASIC Java processor. In addition to standard Java virtual machine benchmarks, several new Java applications are designed to both verify the results and broaden the spectrum of the tests.

Non-Linear Journal Bearing Model for Analysis of Superharmonic Vibrations of Rotor Systems

A rotating machine usually consists of a rotor and bearings that supports it. The nonidealities in these components may excite vibration of the rotating system. The uncontrolled vibrations may lead to excessive wearing of the components of the rotating machine or reduce the process quality. Vibrations may be harmful even when amplitudes are seemingly low, as is usually the case in superharmonic vibration that takes place below the first critical speed of the rotating machine. Superharmonic vibration is excited when the rotational velocity of the machine is a fraction of the natural frequency of the system. In such a situation, a part of the machine’s rotational energy is transformed into vibration energy. The amount of vibration energy should be minimised in the design of rotating machines. The superharmonic vibration phenomena can be studied by analysing the coupled rotor-bearing system employing a multibody simulation approach. This research is focused on the modelling of hydrodynamic journal bearings and rotorbearing systems supported by journal bearings. In particular, the non-idealities affecting the rotor-bearing system and their effect on the superharmonic vibration of the rotating system are analysed. A comparison of computationally efficient journal bearing models is carried out in order to validate one model for further development. The selected bearing model is improved in order to take the waviness of the shaft journal into account. The improved model is implemented and analyzed in a multibody simulation code. A rotor-bearing system that consists of a flexible tube roll, two journal bearings and a supporting structure is analysed employing the multibody simulation technique. The modelled non-idealities are the shell thickness variation in the tube roll and the waviness of the shaft journal in the bearing assembly. Both modelled non-idealities may cause subharmonic resonance in the system. In multibody simulation, the coupled effect of the non-idealities can be captured in the analysis. Additionally one non-ideality is presented that does not excite the vibrations itself but affects the response of the rotorbearing system, namely the waviness of the bearing bushing which is the non-rotating part of the bearing system. The modelled system is verified with measurements performed on a test rig. In the measurements the waviness of bearing bushing was not measured and therefore it’s affect on the response was not verified. In conclusion, the selected modelling approach is an appropriate method when analysing the response of the rotor-bearing system. When comparing the simulated results to the measured ones, the overall agreement between the results is concluded to be good.

Design and evaluation of learning algorithms for dynamic resource management in virtual networks

Network virtualisation is considerably gaining attentionas a solution to ossification of the Internet. However, thesuccess of network virtualisation will depend in part on how efficientlythe virtual networks utilise substrate network resources.In this paper, we propose a machine learning-based approachto virtual network resource management. We propose to modelthe substrate network as a decentralised system and introducea learning algorithm in each substrate node and substrate link,providing self-organization capabilities. We propose a multiagentlearning algorithm that carries out the substrate network resourcemanagement in a coordinated and decentralised way. The taskof these agents is to use evaluative feedback to learn an optimalpolicy so as to dynamically allocate network resources to virtualnodes and links. The agents ensure that while the virtual networkshave the resources they need at any given time, only the requiredresources are reserved for this purpose. Simulations show thatour dynamic approach significantly improves the virtual networkacceptance ratio and the maximum number of accepted virtualnetwork requests at any time while ensuring that virtual networkquality of service requirements such as packet drop rate andvirtual link delay are not affected.

On Transmission System Design for Wireless Broadcasting

This thesis considers aspects related to the design and standardisation of transmission systems for wireless broadcasting, comprising terrestrial and mobile reception. The purpose is to identify which factors influence the technical decisions and what issues could be better considered in the design process in order to assess different use cases, service scenarios and end-user quality. Further, the necessity of cross-layer optimisation for efficient data transmission is emphasised and means to take this into consideration are suggested. The work is mainly related terrestrial and mobile digital video broadcasting systems but many of the findings can be generalised also to other transmission systems and design processes. The work has led to three main conclusions. First, it is discovered that there are no sufficiently accurate error criteria for measuring the subjective perceived audiovisual quality that could be utilised in transmission system design. Means for designing new error criteria for mobile TV (television) services are suggested and similar work related to other services is recommended. Second, it is suggested that in addition to commercial requirements there should be technical requirements setting the frame work for the design process of a new transmission system. The technical requirements should include the assessed reception conditions, technical quality of service and service functionalities. Reception conditions comprise radio channel models, receiver types and antenna types. Technical quality of service consists of bandwidth, timeliness and reliability. Of these, the thesis focuses on radio channel models and errorcriteria (reliability) as two of the most important design challenges and provides means to optimise transmission parameters based on these. Third, the thesis argues that the most favourable development for wireless broadcasting would be a single system suitable for all scenarios of wireless broadcasting. It is claimed that there are no major technical obstacles to achieve this and that the recently published second generation digital terrestrial television broadcasting system provides a good basis. The challenges and opportunities of a universal wireless broadcasting system are discussed mainly from technical but briefly also from commercial and regulatory aspect