Ultralujasta teräksestä valmistetun henkilönostimen teleskooppipuomin kehittäminen

Tässä työssä kehitettiin palo- ja pelastuskäyttöön tarkoitettuun henkilönostimeen teleskooppipuomin profiilit. Profiilien valmistusmateriaalina oli kuumavalssattu, ultraluja säänkestävä rakenneteräs. Työssä kehitettiin standardien ja ohjeiden pohjalta laskentapohja, jolla voidaan tutkia teleskooppipuomin jaksojen tukireaktioita, taivutus- ja vääntömomentteja ja leikkaus ja normaalivoimia. Laskentapohjassa voidaan varioida eri kuormitusten suuntia, teleskooppipuomin sivusuuntaista ulottumaa ja nostokulmaa. Profiilien alustavassa mitoituksessa hyödynnettiin paikallisen lommahduksen huomioon ottavia standardeja ja suunnitteluohjeita. Eri poikkileikkausten ominaisuuksia verrattiin keskenään ja profiili valittiin yhdessä kohdeyrityksen kanssa. Alustavan mitoituksen yhteydessä muodostettiin apuohjelma valitulle poikkileikkaukselle, jolla voitiin tutkia profiilin eri muuttujien vaikutusta mm. paikalliseen lommahdukseen ja jäykkyyteen. Laskentapohjaan sisällytettiin myös optimointirutiini, jolla voitiin minimoida poikkileikkauksen pinta-ala ja tätä kautta profiilin massa. Lopullinen mitoitus suoritettiin elementtimenetelmällä. Mitoituksessa tutkittiin alustavasti mitoitettujen profiilien paikallista lommahdusta lineaarisen stabiilius- ja epälineaarisen analyysin pohjalta. Profiilien jännityksiä tutkittiin tarkemmin mm. varioimalla kuormituksia ja osittelemalla elementtien normaalijännityksiä. Diplomityössä kehitetyllä ja analysoidulla teleskooppipuomilla voitiin keventää jaksojen painoja 15-30 %. Sivusuuntainen ulottuma parani samalla lähes 20 % ja nimelliskuorma kasvoi 25 %.

Influência do material do destilador na composição química das aguardentes de cana: parte II

The quantitative chemical analysis of the Brazilian sugar cane spirit distilled from glass column packaged with copper, stainless steel, aluminum sponge, or porcelain balls is described. The main chemical compounds determined by gas chromatography coupled with flame ionization (FID) and flame photometric (FPD) detectors and liquid chromatography coupled with diode array detector are aldehydes, ketones, carboxylic acids, alcohols, esters and dimethylsulfite (DMS). The spirits produced either in columns filled with copper or aluminum pot still exhibits the lowest DMS contents but the higher sulfate and methanol contents, whereas spirits produced in stainless steel or porcelain showed higher DMS concentration and lower teors of sulfate ion and methanol. These observations are coherent with DMS oxidation to sulfate, with methanol as by product, in the presence of either copper or aluminum.

Determining risk potential through accidents and near-accidents: an empirical study in a steel factory

Fatal and permanently disabling accidents form only one per I cent of all occupational accidents but in many branches of industry they account for more than half the accident costs. Furthermore the human suffering of the victim and his family is greater in severe accidents than in slight ones. For both human and economic reasons the severe accident risks should be identified befor injuries occur. It is for this purpose that different safety analysis methods have been developed . This study shows two new possible approaches to the problem.. The first is the hypothesis that it is possible to estimate the potential severity of accidents independent of the actual severity. The second is the hypothesis that when workers are also asked to report near accidents, they are particularly prone to report potentially severe near accidents on the basis of their own subjective risk assessment. A field study was carried out in a steel factory. The results supported both the hypotheses. The reliability and the validity of post incident estimates of an accident's potential severity were reasonable. About 10 % of accidents were estimated to be potentially critical; they could have led to death or very severe permanent disability. Reported near accidents were significantly more severe, about 60 $ of them were estimated to be critical. Furthermore the validity of workers subjective risk assessment, manifested in the near accident reports, proved to be reasonable. The studied new methods require further development and testing. They could be used both in routine usage in work places and in research for identifying and setting the priorities of accident risks.

Commodity Price Driven Risk Management from Viewpoint of High Grade Steel Alloys

The study of price risk management concerning high grade steel alloys and their components was conducted. This study was focused in metal commodities, of which nickel, chrome and molybdenum were in a central role. Also possible hedging instruments and strategies for referred metals were studied. In the literature part main themes are price formation of Ni, Cr and Mo, the functioning of metal exchanges and main hedging instruments for metal commodities. This section also covers how micro and macro variables may affect metal prices from the viewpoint of short as well as longer time period. The experimental part consists of three sections. In the first part, multiple regression model with seven explanatory variables was constructed to describe price behavior of nickel. Results were compared after this with information created with comparable simple regression model. Additionally, long time mean price reversion of nickel was studied. In the second part, theoretical price of CF8M alloy was studied by using nickel, ferro-chrome and ferro-molybdenum as explanatory variables. In the last section, cross hedging possibilities for illiquid FeCr -metal was studied with five LME futures. Also this section covers new information concerning possible forthcoming molybdenum future contracts as well. The results of this study confirm, that linear regression models which are based on the assumption of market rationality, are not able to reliably describe price development of metals at issue. Models fulfilling assumptions for linear regression may though include useful information of statistical significant variables which have effect on metal prices. According to the experimental part, short futures were found to incorporate the most accurate information concerning the price movements in the future. However, not even 3M futures were able to predict turning point in the market before the faced slump. Cross hedging seemed to be very doubtful risk management strategy for illiquid metals, because correlations coefficients were found to be very sensitive for the chosen time span.

Urinary 2,5-hexanedione in workers exposed to n-hexane: influence of the sample treatment

The aim of the present study was to determine 2,5-hexanedione (2,5-HD), a metabolite of n-hexane, by gas chromatography/flame ionization detection in 31 workers exposed to n-hexane after two types of sample pretreatment, i.e., with (total 2,5-HD) and without (free 2,5-HD) acid hydrolysis. The mean urinary 2,5-HD was 0.52 mg/L (free) and 2.88 mg/L (total), this difference being significant (Student t-test, p < 0.05). The differences in the results according to the sample treatment support the need to modify the current Brazilian legislation, which proposes the analysis of 2,5-HD without indicating whether it is the free or total metabolite.

Engendering Group Support Based Foresight for Capital Intensive Manufacturing Industries - Case Paper and Steel Industry Scenarios by 2018

In recent times of global turmoil, the need for uncertainty management has become ever momentous. The need for enhanced foresight especially concerns capital-intensive industries, which need to commit their resources and assets with long-term planning horizons. Scenario planning has been acknowledged to have many virtues - and limitations - concerning the mapping of the future and illustrating the alternative development paths. The present study has been initiated to address both the need of improved foresight in two capital-intensive industries, i.e. the paper and steel industries and the imperfections in the current scenario practice. The research problem has been approached by engendering a problem-solving vehicle, which combines, e.g. elements of generic scenario process, face-to-face group support methods, deductive scenario reasoning and causal mapping into a fully integrated scenario process. The process, called the SAGES scenario framework, has been empirically tested by creating alternative futures for two capital-intensive industries, i.e. the paper and steel industries. Three scenarios for each industry have been engendered together with the identification of the key megatrends, the most important foreign investment determinants, key future drivers and leading indicators for the materialisation of the scenarios. The empirical results revealed a two-fold outlook for the paper industry, while the steel industry future was seen as much more positive. The research found support for utilising group support systems in scenario and strategic planning context with some limitations. Key perceived benefits include high time-efficiency, productivity and lower resource-intensiveness. Group support also seems to enhance participant satisfaction, encourage innovative thinking and provide the users with personalised qualitative scenarios.

Aerosol particle size distributions at a traffic exposed site and an urban background location in Oporto, Portugal

Aerosol size distributions from 6 to 700 nm were measured simultaneously at an urban background site and a roadside station in Oporto. The particle number concentration was higher at the traffic exposed site, where up to 90% of the size spectrum was dominated by the nucleation mode. Larger aerosol mode diameters were observed in the urban background site possibly due to the coagulation processes or uptake of gases during transport. Factor analysis has shown that road traffic and the neighbour stationary sources localised upwind affect the urban area thought intra-regional pollutant transport.

Corrosion of steel reinforced concrete in the tropical coastal atmosphere of Havana City, Cuba

The influence of chloride deposition rate on concrete using an atmospheric corrosion approach is rarely studied in the literature. Seven exposure sites were selected in Havana City, Cuba, for exposure of reinforced concrete samples. Two significantly different atmospheric corrosivity levels with respect to corrosion of steel reinforced concrete were observed after two years of exposure depending on atmospheric chloride deposition and w/c ratio of the concrete. Changes in corrosion current are related to changes in chloride penetration and chloride atmospheric deposition. The influence of sulphur compound deposition could also be a parameter to consider in atmospheric corrosion of steel reinforced concrete.

Brazilian vodkas have undetectable levels of ethyl carbamate

While in Europe vodka is mainly derived from potatoes or cereals, a large proportion of Brazilian vodka is likely obtained from sugarcane, which contains ethyl carbamate (EC) precursors. EC, in addition to several other contaminants and congeners, were investigated in 32 samples of Brazilian vodka. All samples complied with the Brazilian regulations for congeners and contaminants, having EC content below 0.01 mg/L (detection limit). These results are probably related to the processing of vodka, in particular the use of extractive and rectifying stainless steel distillation columns, which allow the production of high strength spirits with low levels of congeners and contaminants.

Super/subcritical fluid chromatography with packed columns: state of the art and applications

Separations using supercritical fluid chromatography (SFC) with packed columns have been re-discovered and explored in recent years. SFC enables fast and efficient separations and, in some cases, gives better results than high performance liquid chromatography (HPLC). This paper provides an overview of recent advances in SFC separations using packed columns for both achiral and chiral separations. The most important types of stationary phases used in SFC are discussed as well as the most critical parameters involved in the separations and some recent applications.

Chiral separations of mandelic acid by HPLC using molecularly imprinted polymers

Styrene is used in a variety of chemical industries. Environmental and occupational exposures to styrene occur predominantly through inhalation. The major metabolite of styrene is present in two enantiomeric forms, chiral R- and S- hydroxy-1-phenyl-acetic acid (R-and S-mandelic acid, MA). Thus, the concentration of MA, particularly of its enantiomers, has been used in urine tests to determine whether workers have been exposed to styrene. This study describes a method of analyzing mandelic acid using molecular imprinting techniques and HPLC detection to perform the separation of diastereoisomers of mandelic acid. The molecularly imprinted polymer (MIP) was prepared by non-covalent molecular imprinting using (+) MA, (-) MA or (+) phenylalanine, (-) phenylalanine as templates. Methacrylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) were copolymerized in the presence of the template molecules. The bulk polymerization was carried out at 4ºC under UV radiation. The resulting MIP was grounded into 25~44¼m particles, which were slurry packed into analytical columns. After the template molecules were removed, the MIP-packed columns were found to be effective for the chromatographic resolution of (±)-mandelic acid. This method is simpler and more convenient than other chromatographic methods.

A study on the inhibition of mild steel corrosion in hydrochloric acid by pyridoxol hydrochloride

The inhibition of the corrosion of mild steel in 2M hydrochloric acid solutions by Pyridoxol hydrochloride (PXO) has been studied using weight loss and hydrogen evolution techniques. The inhibitor (PXO) exhibited highest inhibition efficiency of 71.93% at the highest inhibitor concentration of 1.0 x 10-2M investigated and a temperature of 303K from weight loss result. Also, inhibition was found to increase with increasing concentration of the inhibitor and decreasing temperature. A first order type of mechanism has been deduced from the kinetic treatment of the weight loss results and the process of inhibition attributed to physical adsorption. The results obtained from the two techniques show that pyridoxol hydrochloride could serve as an effective inhibitor of the corrosion of mild steel in HCl acid solution. The compound obeys the Langmuir adsorption isotherm equation.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Product costing model for laser welded hollow core steel panels

The aim of the study was to create an easily upgradable product costing model for laser welded hollow core steel panels to help in pricing decisions. The theory section includes a literature review to identify traditional and modern cost accounting methodologies, which are used by manufacturing companies. The theory section also presents the basics of steel panel structures and their manufacturing methods and manufacturing costs based on previous research. Activity-Based costing turned out to be the most appropriate methodology for the costing model because of wide product variations. Activity analysis and the determination of cost drivers based on observations and interviews were the key steps in the creation of the model. The created model was used to test how panel parameters affect the costs caused by the main manufacturing stages and materials. By comparing cost structures, it was possible to find the panel types that are the most economic and uneconomic to manufacture. A sensitivity analysis proved that the model gives sufficiently reliable cost information to support pricing decisions. More reliable cost information could be achieved by determining the cost drivers more accurately. Alternative methods for manufacturing the cores were compared with the model. The comparison proved that roll forming can be more advantageous and flexible than press brake bending. However, more extensive research showed that roll forming is possible only when the cores are designed to be manufactured by roll forming. Due to that fact, when new panels are designed consideration should be given to the possibility of using roll forming.