Barlike

El objetivo de este proyecto es el desarrollo de la aplicación Android Barlike. La aplicación pretende ser un espacio social para compartir opiniones y datos sobre restaurantes y bares de tapas.

Catalytic gasification of glycerol in supercritical water

The conversion of glycerol in supercritical water (SCW) was studied at 510-550 °C and a pressure of 350 bars using both a bed of inert and non-porous ZrO2 particles (hydrothermal experiments), and a bed of a 1% Ru/ZrO2 catalyst. Experiments were conducted with a glycerol concentration of 5 wt% in a continuous isothermal fixed-bed reactor at a residence time between 2 and 10 s. Hydrothermolysis of glycerol formed water-soluble products such as acetaldehyde, acetic acid, hydroxyacetone and acrolein, and gases like H2, CO and CO2. The catalyst enhanced the formation of acetic acid, inhibited the formation of acrolein, and promoted gasification of the glycerol decomposition products. Hydrogen and carbon oxides were the main gases produced in the catalytic experiments, with minor amounts of methane and ethylene. Complete glycerol conversion was achieved at a residence time of 8.5 s at 510 °C, and at around 5 s at 550 °C with the 1 wt% Ru/ZrO2 catalyst. The catalyst was not active enough to achieve complete gasification since high yields of primary products like acetic acid and acetaldehyde were still present. Carbon balances were between 80 and 60% in the catalytic experiments, decreasing continuously as the residence time was increased. This was attributed partially to the formation of methanol and acetaldehyde, which were not recovered and analyzed efficiently in our set-up, but also to the formation of carbon deposits. Carbon deposition was not observed on the catalyst particles but on the surface of the inert zirconia particles, especially at high residence time. This was related to the higher concentration of acetic acid and other acidic species in the catalytic experiments, which may polymerize to form tar-like carbon precursors. Because of carbon deposition, hydrogen yields were significantly lower than expected; for instance at 550 °C the hydrogen yield potential was only 50% of the stoichiometric value.

Estudio de la adherencia entre armaduras de materiales compuestos de matriz polimérica (FRP) y hormigón

En este artículo se presentan los resultados del estudio del comportamiento adherente de barras de materiales compuestos de matriz polímero (FRP), con fibras de vidrio (GFRP) y con fibras de carbono (CFRP), como armadura de hormigón. Se realizan un total de 91 ensayos según las normas ACI 440.3R-04 y CSA S806-02. Los parámetros considerados en los ensayos son la resistencia del hormigón,e l acabado superficial,e l tipo de fibra y el diámetro de la barra. Los resultados dan una estimación de la capacidad de adherencia para diferentes tipos de hormigón y armaduras. La diferencia en las propiedades y en el comportamiento adherente se traduce en una respuesta adherencia-deslizamiento distinta

Modelo de comportamiento en sevicio para estructuras reticulares de hormigón. Parte I: Descripción del modelo y ejemplos de aplicación

A general method for instantaneous and time-dependent serviceability analysis of plane concrete frames is presented. The methodology is based in an extension of the classic matrix formulation for bars. The main aspects influencing the behaviour of the structural concrete are considered: cracking, creep, shrinkage or prestress losses. To simulate the effect of cracking a smeared model (developed in Part II) based on the modification of the tensile branch of the concrete stress-strain relationship is adopted. The general approach considered permits the application to different materials and constitutive laws. Sequential construction (sectional and structural), incorporation of reinforcement, consideration of the loads history; placing and removing shores, and restraining or releasing in boundary conditions are considered. Some examples are included to highlight the capabilities of the model

High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

An Interface Damage Model for the Simulation of Delamination Under Variable-Mode Ratio in Composite Materials

A thermodynamically consistent damage model for the simulation of progressive delamination under variable mode ratio is presented. The model is formulated in the context of the Damage Mechanics. The constitutive equation that results from the definition of the free energy as a function of a damage variable is used to model the initiation and propagation of delamination. A new delamination initiation criterion is developed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation proposed accounts for crack closure effets avoiding interfacial penetration of two adjacent layers aftercomplete decohesion. The model is implemented in a finite element formulation. The numerical predictions given by the model are compared with experimental results

Kehittyneiden hitsausprosessien soveltuvuus alumiinin ja hiiliterästen hitsaukseen

Diplomityössä tutkitaan hitsausprosessien kehitystä. Työn kirjallisen osan alku kuvaa hitsauksen nykypäivää ja tulevaisuutta sekä millainen on hitsaava Suomi. Kehittyneiden hitsausprosessien tarkastelu on jaettu hiiliterästen ja alumiinien hitsausprosesseihin. Hiiliteräksien hitsauksen osalta työssä esitellään kitkahitsaus pyörivällä työkalulla, muunnettu lyhytkaarihitsaus, laserhitsaus, laser-hybridihitsaus ja kapearailohitsaus. Alumiinien hitsauksen osalta työssä esitellään laserhitsaus, muunnettu lyhytkaarihitsaus, kitkahitsaus pyörivällä työkalulla ja vaihtovirta MIG hitsaus. Diplomityön käytännönosuudessa todennettiin hitsausprosessien kehitys. Ensimmäisissä hitsauskokeissa hitsattiin merialumiinia eri kaarityypeillä. Vertailua tehdään pulssihitsauksen, lankapulssihitsauksen sekä CMT-kaarihitsauksen välillä. Koehitsaukset osoittavat CMT-hitsauksen tuottavan MIG-pulssihitsausta pienemmät hitsausmuodonmuutokset. CMT-hitsauksessa alumiinin oksidikerros aiheuttaa MIGpulssihitsausta vähemmän ongelmia, sillä kaari syttyy varmemmin suurillakin hitsausnopeuksilla, eikä hitsiin synny huokosia. Hitsausnopeudella 40 cm/min lankapulssihitsauksella ja MIG-pulssihitsauksella päittäisliitoksena hitsattujen vesileikattujen alumiinikappaleiden hitseihin ei syntynyt huokosia. Kokeen perusteella voidaan todeta, ettei oksidikerroksella ollut vaikutusta hitsin onnistumiseen. Hitsauskokeiden toinen osio tutkii hiilimangaaniteräksisen T-palkin kuitulaserhitsausta. Viiden kilowatin laserteholla hitsattiin onnistuneesti viisi metriä pitkiä T-palkkeja hitsausnopeudella 2 m/min. Takymetrimittauksella ja Tritop 3D-koordinaattimittauksella todennettiin laserhitsatun T-palkin hitsausmuodonmuutosten olevan huomattavasti Twin-jauhekaarihitsauksella hitsattua T-palkkia pienemmät.

Environmental policy instruments concerning industrial end-use energy efficiency

Energy efficiency and saving energy are the main question marks when thinking of reducing carbon dioxide emissions or cutting costs. The objective of thesis is to evaluate policy instruments concerning end-use energy efficiency of heavy industry in European Union. These policy instruments may be divided in various ways, but in this thesis the division is to administrative, financial, informative and voluntary instruments. Administrative instruments introduced in this thesis are Directive on Integrated Pollution Prevention and Control, Directive on Energy End-use Efficiency and Energy Services, and Climate and Energy Package. Financial means include energy and emission taxation, EU Emission Trading Scheme and diverse support systems. Informative instruments consist of horizontal BAT Reference Document for Energy Efficiency, as well as substantial EU documents including Green Paper on Energy Efficiency, Action Plan for Energy Efficiency and An Energy Policy for Europe. And finally, voluntary instruments include environmental managements systems like ISO 14001 and EMAS, energy auditing and benchmarking. The efficiency of different policy instruments vary quite a lot. Informative instruments lack the commitment from industry and are thus almost ineffective, contrary to EU Emission Trading Scheme, which is said to be the solution to climate problems. The efficiency of administrative means can be placed between those mentioned and voluntary instruments are still quite fresh to be examined fruitfully. However, each instrument has their potential and challenges. Cases from corporate world strengthen the results from theoretical part. Cases were written mainly on the basis of interviews. The interviewees praised the energy efficiency contract of Finnish industry, but the EU ETS takes the leading role of policy instruments. However, for industry the reductions do not come easily.

Small and Large Scale Dynamics in the Milky Way

This thesis contains dynamical analysis on four different scales: the Solar system, the Sun itself, the Solar neighbourhood, and the central region of the Milky Way galaxy. All of these topics have been handled through methods of potential theory and statistics. The central topic of the thesis is the orbits of stars in the Milky Way. An introduction into the general structure of the Milky Way is presented, with an emphasis on the evolution of the observed value for the scale-length of the Milky Way disc and the observations of two separate bars in the Milky Way. The basics of potential theory are also presented, as well as a developed potential model for the Milky Way. An implementation of the backwards restricted integration method is shown, rounding off the basic principles used in the dynamical studies of this thesis. The thesis looks at the orbit of the Sun, and its impact on the Oort cloud comets (Paper IV), showing that there is a clear link between these two dynamical systems. The statistical atypicalness of the orbit of the Sun is questioned (Paper I), concluding that there is some statistical typicalness to the orbit of the Sun, although it is not very significant. This does depend slightly on whether one includes a bar, or not, as a bar has a clear effect on the dynamical features seen in the Solar neighbourhood (Paper III). This method can be used to find the possible properties of a bar. Finally, we look at the effect of a bar on a statistical system in the Milky Way, seeing that there are not only interesting effects depending on the mass and size of the bar, but also how bars can capture disc stars (Paper II).

Päästöoikeudet metsä- ja metalliteollisuusyritysten taloudellisessa raportoinnissa

Tutkimuksen tavoitteena on selvittää kuinka päästöoikeuksia käsitellään metsä- ja metalliteollisuusyritysten taloudellisessa raportoinnissa. Tutkimuksessa selvitetään myös Euroopan unionin päästökauppajärjestelmän toimintaa. Tutkimuksen teoreettinen viitekehys rakentuu päästökauppaa koskevien tutkimusten sekä IFRS-standardeja koskevan kirjallisuuden pohjalta. Empiirinen tutkimus perustuu kahdeksan yrityksen vuosikertomusten analysointiin. Tutkimustulosten mukaan yritykset eivät sovella yhtenäistä menetelmätapaa päästöoikeuksien kirjanpidollisessa käsittelyssä. Yritykset soveltavat joko nettoperiaatetta tai IFRS-standardien tulkintaa päästöoikeuksista. Päästöoikeudet luokiteltiin aineettomiksi hyödykkeiksi.

Epäpuhtauksien poistaminen prosessivesistä

Kemira Chemicals Oy in Äetsä produces sodium chlorate as its main product. It is produced with electrolysis in electrolyte cells. During the manufacturing process impurities, out of which the largest one is iron, accumulate in the cells. These impurities are removed in cell wash with hydrochloric acid liquid, after which the wash water is precipitated with sodium hydroxide and sodium carbonate, and filtered with filter press. After the treatment the wash water is recycled back to the manufacturing process. The aim of this thesis was primarily to improve the treatment of wash water in order to remove the impurities with low costs. This would result in more impurity-free water and in sufficient capacity of impurity removal. The second aim was to maintain the chromium in the treated wash water because it forms a diaphragm of chromium hydroxide to cathode which prevents the flow of anions to cathode. The literature part investigates properties, use and manufacturing of sodium chlorate, electrolyte cell and its wash technique, and impurities of wash water. The beginning of the applied part investigates alternatives of separation methods which could be used to improve the treatment of wash water. In the experiments an optimum pH for the precipitation of wash water was determined, and a research of the use of sodium hydroxide, sodium carbonate, calcium hydroxide and calcium chloride as a precipitant was carried out. Also a suitable flocculant and a filter cloth for the treatment of wash water were determined. Finally, process changes were introduced, partly by applying the current equipment, and the costs and savings were calculated.

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

High-speed solid-rotor induction machine – calculation program

The aim of this thesis is to utilize the technology developed at LUT and to provide an easy tool for high-speed solid-rotor induction machine preliminary design. Computer aided design tool MathCAD has been chosen as the environment for realizing the calculation program. Four versions of the design program have been made depending on the motor rotor type. The first rotor type is an axially slitted solid-rotor with steel end rings. The next one is an axially slitted solid-rotor with copper end rings. The third machine type is a solid rotor with deep, rectangular copper bars and end rings (squirrel cage). And the last one is a solid-rotor with round copper bars and end rings (squirrel cage). Each type of rotor has its own specialties but a general thread of design is common. This paper follows the structure of the calculating program and explains some features and formulas. The attention is concentrated on the difference between laminated and solid-rotor machine design principles. There is no deep analysis of the calculation ways are presented. References for all solution methods appearing during the design procedure are given for more detailed studying. This thesis pays respect to the latest innovations in solid-rotor machines theory. Rotor ends’ analytical calculation follows the latest knowledge in this field. Correction factor for adjusting the rotor impedance is implemented. The purpose of the created design program is to calculate the preliminary dimensions of the machine according to initial data. Obtained results are not recommended for exact machine development. Further more detailed design should be done in a finite element method application. Hence, this thesis is a practical tool for the prior evaluating of the high-speed machine with different solid-rotor types parameters.