Raman Lidar monitors emissions from sugar cane fires in the State of São Paulo: a pilot-project integrating radar, sodar, aerosol and gas observations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Study of elastic properies of Ti3Al intermetallic compound using the ab initio calculation

The elastic properties of a Ti3Al intermetallic compound were studied using full potential (FP LAPW ) with the APW+lo method. The FP-LAPW is among the most accurate band structure calculations currently available and is based on the density functional theory with general gradient approximation for the exchange and correlation potential. This method provides the structural properties of the ground state as bulk modulus, equilibrium lattice parameter, and equilibrium minimum energy, and the elastic properties as shear modulus, young modulus, Zener coefficient (anisotropy), and Poisson coefficient. The calculated elastic properties are coherent with the elastic properties of the material.

Study of combustion of different biomass and its atmospheric emissions

One of the energy alternatives that provide utility, flexibility, cleanliness and economy is biomass, such as forest waste (wood) and agricultural (sugarcane bagasse, rice husks, coffee pods, etc.). However, with its increasing supply and use grows also the concern of industries to invest in monitoring and control of emissions into the atmosphere, because during biomass burning are emitted as exhaust gases, fine particles known as particulates, which greatly contribute to the triggering of serious health problems to humans, in addition to the environmental damage. With that, this work aimed to conduct a monitoring of particulate and gaseous pollutants emissions to the atmosphere from the burning of various types of biomass used by industries. The equipment used for sampling were the optical monitor DataRAM 4 and the Unigas3000 + gas sampler. The results showed that biomass coffee pods presented the greatest concentration of particulates (485119 μg m-3) with particle diameters between 0.0602 μm and 0.3502 μm, i.e. the most ultrafine particles, harmful to human health and the environment. The largest emissions of CO and NOx were observed, respectively, for the coffee pods (3500 ppm) and for the rice husk (48 ppm). As for the superior calorific value (PCS), the best of fuel, with higher PCS, was the Eucalyptus grandis.

Soil greenhouse gas emissions and their relations to soil attributes in a sugarcane area

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Luminescence properties of the TRIMEB inclusion compound of a europium tris-beta-diketonate

The adduct TRIMEB:Eu(BTA)(3)center dot 2H(2)O was prepared and primarily characterized by photoluminescence (PL), and compared with free Eu(BTA)(3)center dot 2H(2)O. Both spectra show the Eu3+ ion emission, with subtle differences between lines for the free and encapsulated complex. The temperature dependence and chemical stability were studied, taking into account (in the latter case) the PL changes with time. The use of this new material as the emissive layer in OLEDs was tested by its successful incorporation into a device, using a conductive polymer as host. The use of the TRIMEB adduct increased the stability of the device (as compared with the free Eu complex). (C) 2008 Elsevier B.V. All rights reserved.

EMERGENT CONDITIONAL RELATIONS IN A GO/NO-GO PROCEDURE: FIGURE-GROUND AND STIMULUS-POSITION COMPOUND RELATIONS

Past research has demonstrated emergent conditional relations using a go/no-go procedure with pairs of figures displayed side-by-side on a computer screen. The present Study sought to extend applications Of this procedure. In Experiment, 1, we evaluated whether emergent conditional relations Could be demonstrated when two-component stimuli were displayed in figure-ground relationships-abstract figures displayed on backgrounds of different colors. Five normal)), capable adults participated. During training, each two-component stimulus Was presented successively. Responses emitted in the presence of some Stimulus pairs (A1B1, A2B2, A3B3, B1C1, B2C2 and B3C3) were reinforced, whereas responses emitted in the presence of other pairs (A1B2, A1B3, A2B1, A2B3, A3B1, A3B2, B1C2, B1C3, B2C1, B2C3, B3C1 and B3C2) were not. During tests, new configurations (AC and CA) were presented, thus emulating structurally the matching-to-sample tests employed in typical equivalence Studies. All participants showed emergent relations consistent with stimulus equivalence during testing. In Experiment 2, we systematically replicated the procedures with Stimulus compounds consisting Of four figures (A1, A2, C1 and C2) and two locations (left - B1 and right - 132). A,11 6 normally capable adults exhibited emergent stimulus-stimulus relations. Together, these experiments show that the go/no-go procedure is a potentially useful alternative for Studying emergent. conditional relations when matching-to-sample is procedurally cumbersome or impossible to use.

Methodology of CO2 emission evaluation in the life cycle of office building facades

The construction industry is one of the greatest sources of pollution because of the high level of energy consumption during its life cycle. In addition to using energy while constructing a building, several systems also use power while the building is operating, especially the air-conditioning system. Energy consumption for this system is related, among other issues, to external air temperature and the required internal temperature of the building. The facades are elements which present the highest level of ambient heat transfer from the outside to the inside of tall buildings. Thus, the type of facade has an influence on energy consumption during the building life cycle and, consequently, contributes to buildings' CO2 emissions, because these emissions are directly connected to energy consumption. Therefore, the aim is to help develop a methodology for evaluating CO2 emissions generated during the life cycle of office building facades. The results, based on the parameters used in this study, show that facades using structural glazing and uncolored glass emit the most CO2 throughout their life cycle, followed by brick facades covered with compound aluminum panels or ACM (Aluminum Composite Material), facades using structural glazing and reflective glass and brick facades with plaster coating. On the other hand, the typology of facade that emits less CO2 is brickwork and mortar because its thermal barrier is better than structural glazing facade and materials used to produce this facade are better than brickwork and ACM. Finally, an uncertainty analysis was conducted to verify the accuracy of the results attained. (C) 2011 Elsevier Inc. All rights reserved.

Structure and antimycobacterial activity of the novel organometallic [Pd(C-bzan)(SCN)(dppp)] compound

The organometallic compound [Pd(C-bzan)(SCN)(dppp)] {bzan = N-benzylideneaniline, dppp = 1,3-bis(diphenylphosphino)propane} was synthesized and characterized by elemental analyses, infrared and H-1 and P-31(H-1) NMR spectroscopies. The crystal and molecular structures of the title complex were determined by single-crystal X-ray diffraction techniques. In vitro antimycobacterial evaluation demonstrated that the compound [Pd(C-bzan)(SCN)(dppp)] displayed a MIC of 5.15 mu M, which is superior than those values found for some commonly used anti-TB drugs and other Pd(II) complexes. (C) 2012 Elsevier B.V. All rights reserved.

Grain size effect on the structural and dielectric properties of Pb0.85La0.15TiO3 ferroelectric ceramic compound

This paper presents a study of the influence of particle size on the structural and dielectric properties of Pb0.85La0.15TiO3 (PLT15) ferroelectric ceramic samples. The samples were prepared with average grain size of 1.69 +/- 0.08 mu m and 146 +/- 8 nm using, respectively, conventional and spark plasma sintering techniques. A decrease in the tetragonality degree as the crystallite size decreased was explained by an internal stress caused by the existence of a large amount of grain boundaries. The local structure exhibited no significant modification and the dielectric measurements showed a diffuse phase transition and a reduction in the permittivity magnitude at T-m as the average grain size decreased. The nanostructured ceramic sample prepared at a relatively lower temperature and sintering time presented a dielectric constant value of approximately 2000 at room temperature. (c) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Obtaining NiAl intermetallic compound using different milling devices

NiAl intermetallic compound was synthesized by mechanical alloying technique in planetary and attritor mills. The starting powders consisted of elemental mixtures of Ni and Al at Ni50Al50(at%) composition. In the planetary mill, compound formation occurred gradually during mechanical alloying, while the occurrence of a mechanically induced self-propagating reaction (MSR) can be suggested in the attritor mill. The NiAl obtained in both mill types was partially disordered with long-range order parameter not inferior to 0.66. Quantitative phase analysis using the Rietveld method was performed in as-milled samples, and this method was also employed to estimate changes in crystallite size and lattice strain of the NiAl produced during mechanical alloying. (C) 2011 The Society of Powder Technology Japan. Published by Elsevier B.V. and The Society of Powder Technology Japan. All rights reserved.

Properties of nanoparticles prepared from NdFeB-based compound for magnetic hyperthermia application

Nanoparticles were prepared from a NdFeB-based alloy using the hydrogen decrepitation process together with high-energy ball milling and tested as heating agent for magnetic hyperthermia. In the milling time range evaluated (up to 10 h), the magnetic moment per mass at H = 1.59 MA m(-1) is superior than 70 A m(2) kg(-1); however, the intrinsic coercivity might be inferior than 20 kA m(-1). The material presents both ferromagnetic and superparamagnetic particles constituted by a mixture of phases due to the incomplete disproportionation reaction of Nd2Fe14BHx during milling. Solutions prepared with deionized water and magnetic particles exposed to an AC magnetic field (H-max similar to 3.7 kA m(-1) and f = 228 kHz) exhibited 26 K <= Delta T-max <= 44 K with a maximum estimated specific absorption rate (SAR) of 225 W kg(-1). For the pure magnetic material milled for the longest period of time (10 h), the SAR was estimated as similar to 2500 W kg(-1). In vitro tests indicated that the powders have acceptable cytotoxicity over a wide range of concentration (0.1-100 mu g ml(-1)) due to the coating applied during milling.

Antibacterial compound from the endophytic fungus Phomopsis longicolla isolated from the tropical red seaweed Bostrychia radicans

Endophytic fungi isolated from the red seaweed Bostrychia radicans were studied to identify their molecularly diverse and biologically active natural chemical products. According to 28S ribosomal DNA-based identification, the strain named C81 was 98% identical to Phomopsis longicolla. This strain was cultivated in solid rice medium and produced three major metabolites identified as 18-deoxycytochalasin H (1), mycophenolic acid (2), and dicerandrol C (3). The chemical structures of these compounds were elucidated by 1D and 2D nuclear magnetic resonance as well as by mass spectrometry. Dicerandrol C had significant antimicrobial activity against Staphylococcus aureus (ATCC 6538) and Staphylococcus saprophyticus (ATCC 15305), with minimum inhibitory concentrations of 1 and 2 mu g ml(-1) (1.33 and 2.66 mu M), respectively. These results show the presence of promising metabolites and indicate that these natural products should be considered in the development of new antibiotics.

Combustion of coal, bagasse and blends thereof Part I: Emissions from batch combustion of fixed beds of fuels

Batch combustion of fixed beds of coal, bagasse and blends thereof took place in a pre-heated two-stage electric laboratory furnace, under high-heating rates. The average input fuel/air equivalence ratios were similar for all fuels. The primary and secondary furnace temperatures were varied from 800 degrees C to 1000 degrees C. The effects of fuel blending, combustion staging, and operating furnace temperatures on the emissions from the two fuels were assessed. Furnace effluents were analyzed for carbon dioxide and for products of incomplete combustion (PIC) including CO, volatile and semi-volatile hydrocarbons, as well as particulate matter. Results showed that whereas CO2 was generated during both the observed sequential volatile matter and char combustion phases of the fuels, PICs were only generated during the volatile matter combustion phase. CO2 emissions were the highest from coal, whereas CO and other PIC emissions were the highest from bagasse. Under this particular combustion configuration, combustion of the volatile matter of the blends resulted in lower yields of PIC, than combustion of the volatiles of the neat fuels. Though CO and unburned hydrocarbons from coal as well as from the blends did not exhibit a clear trend with furnace temperature, such emissions from bagasse clearly increased with temperature. The presence of the secondary furnace (afterburner) typically reduced PIC, by promoting further oxidation of the primary furnace effluents. (C) 2012 Elsevier Ltd. All rights reserved.

Polarization effect on the two-photon absorption of a chiral compound

In this report, we investigate the polarization effect (linear, elliptical and circular) on the two-photon absorption (2PA) properties of a chiral compound based in azoaromatic moieties using the femtosecond Z-scan technique with low repetition rate and low pulse energy. We observed a strong 2PA modulation between 800 nm and 960 nm as a function the polarization changes from linear through elliptical to circular. Such results were interpreted employing the sum-over-essential states approach, which allowed us to model the 2PA circular-linear dichroism effect and to identifier the overlapping of the excited electronic states responsible by the 2PA allowed band. (C) 2012 Optical Society of America

Combustion of coal, bagasse and blends thereof Part II: Speciation of PAH emissions

This work reports on emissions of unburned hydrocarbon species from batch combustion of fixed beds of coal, sugar-cane bagasse, and blends thereof in a pre-heated two-stage laboratory furnace operated in the temperature range of 800-1000 degrees C. The effects of fuel blending, combustion staging, and operating furnace temperatures on emissions of pollutants were assessed. Furnace effluents were analyzed for products of incomplete combustion (PICs) including CO, volatile and semi-volatile hydrocarbons, and particulate matter, as has been reported in Ref. [1]. Emitted unburned hydrocarbons include traces of potentially health-hazardous Polycyclic Aromatic Hydrocarbons (PAHs), which are the focus of this work. Under the batch combustion conditions implemented herein, PAH were only generated during the volatile combustion phase of the fuels. The most prevalent species were in descending order: naphthalene, acenaphthylene, phenanthrene, fluoranthene, pyrene, dibenzofuran, benzofuran, byphenyl, fluorene, 9H-fluoren-9-one, acephenantrylene, benzo[b] fluoranthene, 1-methyl-naphthalene; 2-methyl-naphthalene, benz[a] anthracene and benzo[a] pyrene. PAH yields were the highest from combustion of neat bagasse. Combustion of the blends resulted in lower yields of PAH, than combustion of either of their neat fuel constituents. Increasing the furnace operating temperature enhanced the PAH emissions from bagasse, but had little effect on those from the coal or from the blends. Flue gas treatment in a secondary-stage furnace, upon with additional air, typically reduced PAH yields by promoting oxidation of the primary-stage furnace effluents. (C) 2011 Elsevier Ltd. All rights reserved.