Entwicklung, Aufbau und Messungen eines schnellen Eiskeimzählers

Im Rahmen dieser Arbeit wurde ein neuer Eiskeimzähler FINCH (Fast Ice Nucleus CHamber) entwickelt und erste Messungen von verschiedenen Testaerosolen im Labor und atmosphärischem Aerosol durchgeführt. Die Aerosolpartikel bzw. Ice Nuclei IN werden bei Temperaturen unter dem Gefrierpunkt und Übersättigungen in Bezug auf Eis zum Anwachsen zu Eiskristallen gebracht, um sie mittels optischer Detektion zu erfassen. In FINCH ist dies durch das Prinzip der Mischung realisiert, wodurch eine kontinuierliche Messung der IN-Anzahlkonzentration gewährleistet ist. Hierbei kann mit sehr hohen Sammelflussraten von bis zu 10 l/min gemessen werden. Ebenso ist ein schnelles Abfahren von verschiedenen Sättigungsverhältnissen in Bezug auf Eis in einem weiten Bereich von 0.9 - 1.7 bei konstanten Temperaturen bis zu −23 °C möglich. Die Detektion der Eiskristalle und damit der Bestimmung der IN-Anzahlkonzentration erfolgt über einen neu entwickelten optischen Sensor basierend auf der unterschiedlichen Depolarisation des zurückgestreuten Lichtes von Eiskristallen und unterkühlten Tropfen. In Labermessungen wurden Aktivierungstemperatur und -sättigungsverhältnis von Silberjodid AgI und Kaolinit vermessen. Die Resultate zeigten gute Übereinstimmungen mit Ergebnissen aus der Literatur sowie Parallelmessungen mit FRIDGE (FRankfurt Ice Deposition freezinG Experiment). FRIDGE ist eine statische Diffusionskammer zur Aktivierung und Auszählung von Eiskeimen, die auf einem Filter gesammelt wurden. Bei atmosphärischen Messungen auf dem Jungfraujoch(Schweiz) lagen die IN-Anzahlkonzentrationen mit bis zu 4 l−1 im Rahmen der aus der Literatur bekannten Werte. Messungen der Eiskristallresiduen von Mischwolken zeigten hingegen, dass nur jedes tausendste als Eiskeim im Depositionsmode aktiv ist. Hier scheinen andere Gefrierprozesse und sekundäre Eiskristallbildung von sehr großer Bedeutung für die Anzahlkonzentration der Eiskristallresiduen zu sein. Eine weitere Messung von atmosphärischem Aerosol in Frankfurt zeigte IN-Anzahlkonzentrationen bis zu 30 l−1 bei Aktivierungstemperaturen um −14 °C. Die parallele Probenahme auf Siliziumplättchen für die Messungen der IN-Anzahlkonzentration in FRIDGE ergaben Werte im gleichen Anzahlkonzentrationsbereich.

Towards a new test of time dilation: Laser spectroscopy on lithium ions stored at a velocity of 33.8 % of the speed of light

The subject of the presented thesis is the accurate measurement of time dilation, aiming at a quantitative test of special relativity. By means of laser spectroscopy, the relativistic Doppler shifts of a clock transition in the metastable triplet spectrum of ^7Li^+ are simultaneously measured with and against the direction of motion of the ions. By employing saturation or optical double resonance spectroscopy, the Doppler broadening as caused by the ions' velocity distribution is eliminated. From these shifts both time dilation as well as the ion velocity can be extracted with high accuracy allowing for a test of the predictions of special relativity. A diode laser and a frequency-doubled titanium sapphire laser were set up for antiparallel and parallel excitation of the ions, respectively. To achieve a robust control of the laser frequencies required for the beam times, a redundant system of frequency standards consisting of a rubidium spectrometer, an iodine spectrometer, and a frequency comb was developed. At the experimental section of the ESR, an automated laser beam guiding system for exact control of polarisation, beam profile, and overlap with the ion beam, as well as a fluorescence detection system were built up. During the first experiments, the production, acceleration and lifetime of the metastable ions at the GSI heavy ion facility were investigated for the first time. The characterisation of the ion beam allowed for the first time to measure its velocity directly via the Doppler effect, which resulted in a new improved calibration of the electron cooler. In the following step the first sub-Doppler spectroscopy signals from an ion beam at 33.8 %c could be recorded. The unprecedented accuracy in such experiments allowed to derive a new upper bound for possible higher-order deviations from special relativity. Moreover future measurements with the experimental setup developed in this thesis have the potential to improve the sensitivity to low-order deviations by at least one order of magnitude compared to previous experiments; and will thus lead to a further contribution to the test of the standard model.

Scaled down physical properties of semiconductor nanowires for nanoelectronics scaling up

Semiconductor nanowires (NWs) are one- or quasi one-dimensional systems whose physical properties are unique as compared to bulk materials because of their nanoscaled sizes. They bring together quantum world and semiconductor devices. NWs-based technologies may achieve an impact comparable to that of current microelectronic devices if new challenges will be faced. This thesis primarily focuses on two different, cutting-edge aspects of research over semiconductor NW arrays as pivotal components of NW-based devices. The first part deals with the characterization of electrically active defects in NWs. It has been elaborated the set-up of a general procedure which enables to employ Deep Level Transient Spectroscopy (DLTS) to probe NW arrays’ defects. This procedure has been applied to perform the characterization of a specific system, i.e. Reactive Ion Etched (RIE) silicon NW arrays-based Schottky barrier diodes. This study has allowed to shed light over how and if growth conditions introduce defects in RIE processed silicon NWs. The second part of this thesis concerns the bowing induced by electron beam and the subsequent clustering of gallium arsenide NWs. After a justified rejection of the mechanisms previously reported in literature, an original interpretation of the electron beam induced bending has been illustrated. Moreover, this thesis has successfully interpreted the formation of NW clusters in the framework of the lateral collapse of fibrillar structures. These latter are both idealized models and actual artificial structures used to study and to mimic the adhesion properties of natural surfaces in lizards and insects (Gecko effect). Our conclusion are that mechanical and surface properties of the NWs, together with the geometry of the NW arrays, play a key role in their post-growth alignment. The same parameters open, then, to the benign possibility of locally engineering NW arrays in micro- and macro-templates.

Computer simulations of colloidal fluids in confinement

Computer-Simulationen von Kolloidalen Fluiden in Beschränkten Geometrien Kolloidale Suspensionen, die einen Phasenübergang aufweisen, zeigen eine Vielfalt an interessanten Effekten, sobald sie auf eine bestimmte Geometrie beschränkt werden, wie zum Beispiel auf zylindrische Poren, sphärische Hohlräume oder auf einen Spalt mit ebenen Wänden. Der Einfluss dieser verschiedenen Geometrietypen sowohl auf das Phasenverhalten als auch auf die Dynamik von Kolloid-Polymer-Mischungen wird mit Hilfe von Computer-Simulationen unter Verwendung des Asakura-Oosawa- Modells, für welches auf Grund der “Depletion”-Kräfte ein Phasenübergang existiert, untersucht. Im Fall von zylindrischen Poren sieht man ein interessantes Phasenverhalten, welches vom eindimensionalen Charakter des Systems hervorgerufen wird. In einer kurzen Pore findet man im Bereich des Phasendiagramms, in dem das System typischerweise entmischt, entweder eine polymerreiche oder eine kolloidreiche Phase vor. Sobald aber die Länge der zylindrischen Pore die typische Korrelationslänge entlang der Zylinderachse überschreitet, bilden sich mehrere quasi-eindimensionale Bereiche der polymerreichen und der kolloidreichen Phase, welche von nun an koexistieren. Diese Untersuchungen helfen das Verhalten von Adsorptionshysteresekurven in entsprechenden Experimenten zu erklären. Wenn das Kolloid-Polymer-Modellsystem auf einen sphärischen Hohlraum eingeschränkt wird, verschiebt sich der Punkt des Phasenübergangs von der polymerreichen zur kolloidreichen Phase. Es wird gezeigt, dass diese Verschiebung direkt von den Benetzungseigenschaften des Systems abhängt, was die Beobachtung von zwei verschiedenen Morphologien bei Phasenkoexistenz ermöglicht – Schalenstrukturen und Strukturen des Janustyps. Im Rahmen der Untersuchung von heterogener Keimbildung von Kristallen innerhalb einer Flüssigkeit wird eine neue Simulationsmethode zur Berechnung von Freien Energien der Grenzfläche zwischen Kristall- bzw. Flüssigkeitsphase undWand präsentiert. Die Resultate für ein System von harten Kugeln und ein System einer Kolloid- Polymer-Mischung werden anschließend zur Bestimmung von Kontaktwinkeln von Kristallkeimen an Wänden verwendet. Die Dynamik der Phasenseparation eines quasi-zweidimensionalen Systems, welche sich nach einem Quench des Systems aus dem homogenen Zustand in den entmischten Zustand ausbildet, wird mit Hilfe von einer mesoskaligen Simulationsmethode (“Multi Particle Collision Dynamics”) untersucht, die sich für eine detaillierte Untersuchung des Einflusses der hydrodynamischen Wechselwirkung eignet. Die Exponenten universeller Potenzgesetze, die das Wachstum der mittleren Domänengröße beschreiben, welche für rein zwei- bzw. dreidimensionale Systeme bekannt sind, können für bestimmte Parameterbereiche nachgewiesen werden. Die unterschiedliche Dynamik senkrecht bzw. parallel zu den Wänden sowie der Einfluss der Randbedingungen für das Lösungsmittel werden untersucht. Es wird gezeigt, dass die daraus resultierende Abschirmung der hydrodynamischen Wechselwirkungsreichweite starke Auswirkungen auf das Wachstum der mittleren Domänengröße hat.

"La scienza in cucina e l'arte di mangiar bene" di Pellegrino Artusi. Proposta di glossario culinario italiano-russo

L'obiettivo della tesi è la compilazione del glossario culinario italiano-russo che “racchiudere” termini culinari artusiani e propone una versione russa basandosi anche sulla traduzione parziale del libro in lingua russa. La tesi si divide in sette parti: introduzione, capitoli primo, secondo, terzo e quarto, conclusione e bibliografia. Il primo capitolo introduce la figura di Pellegrino Artusi con brevi cenni sulla sua vita e tratteggia, altresì, le peripezie ed il successo internazionale della sua opera ed il suo approdo in Russia. Il secondo capitolo è dedicato alla ricerca terminologica e alle fasi propedeutiche alla creazione del glossario. Inoltre, vengono spiegate le risorse usate per la creazione dei corpora. Avendo a disposizione la traduzione parziale de “La scienza in cucina e l'arte di mangiar bene” in russo (traduzione di I. Alekberova) fornita dalla Casa Artusi, si cerca di spiegare la scelta dei termini italiani messi a confronto con quelli esistenti nella traduzione russa. Il terzo capitolo introduce il glossario stesso preceduto da una breve spiegazione. Ogni “entrata” contiene il termine, la sua categoria grammaticale e la sua definizione in entrambe le lingue, seguita nella maggior parte dei casi dalle collocazioni o dagli esempi d'uso oppure dai sinonimi. Il quarto capitolo presenta commenti alla compilazione del glossario. Qui vengono analizzati i problemi riscontrati durante la fase compilativa, si presentano le soluzioni trovate e si forniscono esempi concreti. Ci sono anche commenti alle voci non presenti nel glossario. Infine, vi è una breve conclusione del percorso affrontato seguita dalla bibliografia e dalla sitografia. ENGLISH The purpose of this dissertation is to present a bilingual Italian-Russian glossary based on the culinary terms drawn from Artusi's cooking book "The Science of Cooking and the Art of Fine dining". The dissertation consists of an introduction, 4 chapters, conclusions and a list of bibliography. An introduction presents an overview of the entire dissertation. The first chapter includes a presentation of Pellegrino Artusi, brief introduction to his life, his book and the success it has had around the world and mainly in Russia. The second chapter focuses on the creation and use of comparable and parallel corpora that have been created ad hoc for the purpose of the glossary. It also describes the different programs that have been used in order to select the terminology. The third chapter presents the structure of the bilingual culinary glossary followed by the glossary itself. Each entry contains the term, its gramatical category and the definition in both languages followed by, in most but not all cases, collocation, synonyms and additional notes. The fourth chapter presents an analysis of the compilation of the glossary combined with comments and examples. This chapter is followed by final conclusions of the present dissertation. The last part contains a bibliography that includes all the resources that have been used for the completion of this dissertation followed by the webliography.

The organization of memory for familiar songs

Investigated the organizing principles in memory for familiar songs in 2 experiments. It was hypothesized that individuals do not store and remember each song in isolation. Rather, there exists a rich system of relationships among tunes that can be revealed through similarity rating studies and memory tasks. One initial assumption was the division of relations among tunes into musical (e.g., tempo, rhythm) and nonmusical similarity. In Exp I, 20 undergraduates were asked to sort 60 familiar tunes into groups according to both musical and nonmusical criteria. Clustering analyses showed clear patterns of nonmusical similarity but few instances of musical similarity. Exp II, with 16 Ss, explored the psychological validity of the nonmusical relationships revealed in Exp I. A speeded verification task showed that songs similar to each other are confused more often than are distantly related songs. A free-recall task showed greater clustering for closely related songs than for distantly related ones. The relationship between these studies and studies of semantic memory is discussed. Also, the contribution of musical training and individual knowledge to the organization of the memory system is considered. (19 ref) (PsycINFO Database Record (c) 2012 APA, all rights reserved)

FPGA BASED DESIGN FOR ACCELERATED FAULT-TESTING OF INTEGRATED CIRCUITS

In the past few decades, integrated circuits have become a major part of everyday life. Every circuit that is created needs to be tested for faults so faulty circuits are not sent to end-users. The creation of these tests is time consuming, costly and difficult to perform on larger circuits. This research presents a novel method for fault detection and test pattern reduction in integrated circuitry under test. By leveraging the FPGA's reconfigurability and parallel processing capabilities, a speed up in fault detection can be achieved over previous computer simulation techniques. This work presents the following contributions to the field of Stuck-At-Fault detection: We present a new method for inserting faults into a circuit net list. Given any circuit netlist, our tool can insert multiplexers into a circuit at correct internal nodes to aid in fault emulation on reconfigurable hardware. We present a parallel method of fault emulation. The benefit of the FPGA is not only its ability to implement any circuit, but its ability to process data in parallel. This research utilizes this to create a more efficient emulation method that implements numerous copies of the same circuit in the FPGA. A new method to organize the most efficient faults. Most methods for determinin the minimum number of inputs to cover the most faults require sophisticated softwareprograms that use heuristics. By utilizing hardware, this research is able to process data faster and use a simpler method for an efficient way of minimizing inputs.

Evaluation of 41calcium as a new approach to assess changes in bone metabolism: effect of a bisphosphonate intervention in postmenopausal women with low bone mass

A new technique was evaluated to identify changes in bone metabolism directly at high sensitivity through isotopic labeling of bone Ca. Six women with low BMD were labeled with 41Ca up to 700 days and treated for 6 mo with risedronate. Effect of treatment on bone could be identified using 41Ca after 4-8 wk in each individual. INTRODUCTION: Isotopic labeling of bone using 41Ca, a long-living radiotracer, has been proposed as an alternative approach for measuring changes in bone metabolism to overcome current limitations of available techniques. After isotopic labeling of bone, changes in urinary 41Ca excretion reflect changes in bone Ca balance. The aim of this study was to validate this new technique against established measures. Changes in bone Ca balance were induced by giving a bisphosphonate. MATERIALS AND METHODS: Six postmenopausal women with diagnosed osteopenia/osteoporosis received a single oral dose of 100 nCi 41Ca for skeleton labeling. Urinary 41Ca/40Ca isotope ratios were monitored by accelerator mass spectrometry up to 700 days after the labeling process. Subjects received 35 mg risedronate per week for 6 mo. Effect of treatment was monitored using the 41Ca signal in urine and parallel measurements of BMD by DXA and biochemical markers of bone metabolism in urine and blood. RESULTS: Positive response to treatment was confirmed by BMD measurements, which increased for spine by +3.0% (p = 0.01) but not for hip. Bone formation markers decreased by -36% for bone alkaline phosphatase (BALP; p = 0.002) and -59% for procollagen type I propeptides (PINP; p = 0.001). Urinary deoxypyridinoline (DPD) and pyridinoline (PYD) were reduced by -21% (p = 0.019) and -23% (p = 0.009), respectively, whereas serum and urinary carboxy-terminal teleopeptides (CTXs) were reduced by -60% (p = 0.001) and -57.0% (p = 0.001), respectively. Changes in urinary 41Ca excretion paralleled findings for conventional techniques. The urinary 41Ca/40Ca isotope ratio was shifted by -47 +/- 10% by the intervention. Population pharmacokinetic analysis (NONMEM) of the 41Ca data using a linear three-compartment model showed that bisphosphonate treatment reduced Ca transfer rates between the slowly exchanging compartment (bone) and the intermediate fast exchanging compartment by 56% (95% CI: 45-58%). CONCLUSIONS: Isotopic labeling of bone using 41Ca can facilitate human trials in bone research by shortening of intervention periods, lowering subject numbers, and having easier conduct of cross-over studies compared with conventional techniques.

Stakeholder analysis combined with social network analysis provides fine-grained insights into water infrastructure planning processes

Environmental policy and decision-making are characterized by complex interactions between different actors and sectors. As a rule, a stakeholder analysis is performed to understand those involved, but it has been criticized for lacking quality and consistency. This lack is remedied here by a formal social network analysis that investigates collaborative and multi-level governance settings in a rigorous way. We examine the added value of combining both elements. Our case study examines infrastructure planning in the Swiss water sector. Water supply and wastewater infrastructures are planned far into the future, usually on the basis of projections of past boundary conditions. They affect many actors, including the population, and are expensive. In view of increasing future dynamics and climate change, a more participatory and long-term planning approach is required. Our specific aims are to investigate fragmentation in water infrastructure planning, to understand how actors from different decision levels and sectors are represented, and which interests they follow. We conducted 27 semi-structured interviews with local stakeholders, but also cantonal and national actors. The network analysis confirmed our hypothesis of strong fragmentation: we found little collaboration between the water supply and wastewater sector (confirming horizontal fragmentation), and few ties between local, cantonal, and national actors (confirming vertical fragmentation). Infrastructure planning is clearly dominated by engineers and local authorities. Little importance is placed on longer-term strategic objectives and integrated catchment planning, but this was perceived as more important in a second analysis going beyond typical questions of stakeholder analysis. We conclude that linking a stakeholder analysis, comprising rarely asked questions, with a rigorous social network analysis is very fruitful and generates complementary results. This combination gave us deeper insight into the socio-political-engineering world of water infrastructure planning that is of vital importance to our well-being.

Identification of gunshots to the head by detection of RNA in backspatter primarily expressed in brain tissue

Traces of backspatter recovered from the inside of the barrel of a gun that was used to deliver suicidal or homicidal contact shots may be a source of valuable forensic evidence and first systematic investigations of the persistence of victim DNA from inside firearms have been presented. The aim of the present study was to include victim RNA in such analyses to determine the origin of tissues in addition and parallel to standard DNA profiling for forensic identification purposes. In a first step, suitable mRNA (C1orf61) and micro-RNAs (miR-124a and miR-124*) that are primarily expressed in brain tissue were selected from potential candidates and confirmed using quantitative PCR (qPCR). Secondly, a co-extraction procedure for RNA and DNA was established and brain differentiability of the selected RNAs was demonstrated via qPCR using samples from experimental shots at ballistic models. In a third step, this procedure was successfully applied to analyse samples from real casework comprising eight cases of suicidal contact shots. In this pilot study, we are first to report the possibility of co-extracting mRNA, miRNA and DNA from ballistic trace samples collected from the inside of firearms and we demonstrate that RNA and DNA based analyses can be performed in parallel to produce informative and highly complementary evidence.

Serosurveillance of Schmallenberg virus in Switzerland using bulk tank milk samples.

Infections with Schmallenberg virus (SBV), a novel Orthobunyavirus transmitted by biting midges, can cause abortions and malformations of newborns and severe symptoms in adults of domestic and wild ruminants. Understanding the temporal and spatial distribution of the virus in a certain territory is important for the control and prevention of the disease. In this study, seroprevalence of antibodies against SBV and the spatial spread of the virus was investigated in Swiss dairy cattle applying a milk serology technique on bulk milk samples. The seroprevalence in cattle herds was significantly higher in December 2012 (99.5%) compared to July 2012 (19.7%). This high between-herd seroprevalence in cattle herds was observed shortly after the first detection of viral infections. Milk samples originating from farms with seropositive animals taken in December 2012 (n=209; mean 160%) revealed significantly higher S/P% ratios than samples collected in July 2012 (n=48; mean 103.6%). This finding suggests a high within-herd seroprevalence in infected herds which makes testing of bulk tank milk samples for the identification farms with past exposures to SBV a sensitive method. It suggests also that within-herd transmission followed by seroconversion still occurred between July and December. In July 2012, positive bulk tank milk samples were mainly restricted to the western part of Switzerland whereas in December 2012, all samples except one were positive. A spatial analysis revealed a separation of regions with and without positive farms in July 2012 and no spatial clustering within the regions with positive farms. In contrast to the spatial dispersion of bluetongue virus, a virus that is also transmitted by Culicoides midges, in 2008 in Switzerland, the spread of SBV occurred from the western to the eastern part of the country. The dispersed incursion of SBV took place in the western part of Switzerland and the virus spread rapidly to the remaining territory. This spatial pattern is consistent with the hypothesis that transmission by Culicoides midges was the main way of spreading.

Youth empowerment evaluation to improve afterschool programming

Community-based participatory research necessitates that community members act as partners in decision making and mutual learning and discovery. In the same light, for programs/issues involving youth, youth should be partners in knowledge sharing and evaluation (Checkoway & Richards-Schuster, 2004). This study is a youth-focused empowerment evaluation for the Successful Youth program. Successful Youth is a multi-component youth development after-school program for Latino middle school youth, created with the goal of reducing teen pregnancy. An empowerment evaluation is collaborative and participatory (Balcazar and Harper 2003). The three steps of an empowerment evaluation are: (1) defining mission, (2) taking stock, and (3) planning for the future (Fetterman 2001).^ In a program where youth are developing leadership skills, making choices, and learning how to self reflect and evaluate, the empowerment evaluation could not be more aligned with promoting and enhancing these skills. In addition, an empowerment evaluation is designed to "foster improvement and self-determination" and "build capacity" (Fetterman 2001). Four empowerment groups were conducted with approximately 6-9 Latino 7th grade students per group. All participants were enrolled in the Successful Youth program. Results indicate points where students' perceptions of the program were aligned with the program's mission and where gaps were identified. Students offered recommendations for program improvements. Additionally, students enjoyed expressing their feelings about the program and appreciated that their opinions were valued. Youth recommendations will be brought to program staff; and, where possible, gaps will be addressed. Empowerment evaluations with youth will continue during the duration of the program so that youth involvement and input remains integral in the evaluation and to ascertain whether the program's goals are being met. ^

Use of empowerment evaluation to determine a sustainability plan for a community-based preconception care program

Women With IMPACT (WWI) is a community-based preconception care educational intervention. WWI is being implemented by the Impacting Maternal and Prenatal Care Together (IMPACT) Collaborative and targets zip codes in Harris County, Texas at high risk for infant mortality, low birthweight, and preterm birth. WWI started March 2012 and continues through August 2013. Three workshop series are planned. This study was conducted with participants and facilitators from the first workshop series. This study aimed to 1) evaluate the WWI program using empowerment evaluation, 2) engage all WWI stakeholders in an empowerment evaluation so the method could be adopted as a participatory evaluation process for future IMPACT activities, and 3) develop recommendations for sustainability of the WWI intervention, based on empowerment evaluation findings and results from the pre/post program evaluation completed by WWI participants. Study participants included WWI participants and facilitators and IMPACT Collaborative Steering Committee members. WWI participants were female, 18-35 year-old, non-pregnant residents of zip codes at high risk of adverse birth outcomes. All other study participants were 18 years or older. A two-phased empowerment evaluation (EE) was utilized in this study. Sessions 1-4 were conducted independently of one another – 3 with participants at different sites and one with the facilitators. The fifth session included WWI participant and facilitator representatives, and IMPACT Steering Committee members. Session 5 built upon the work of the other sessions. Observation notes were recorded during each session. Thematic content analysis was conducted on all EE tables and observation notes. Mission statements drafted by each group focused on improvement of physical and mental health through behavior change and empowerment of all participants. The top 5 overall program components were: physical activity, nutrition, self-worth, in-class communication, and stress. Goals for program improvement were set by EE participants for each of these components. Through thematic content analysis of the tables and observation notes, social support emerged as an important theme of the program among all participant groups. Change to a healthy lifestyle emerged as an important theme in terms of program improvement. Two-phased EE provided an opportunity for all program stakeholders to provide feedback regarding important program components and provide suggestions for program improvement. EE, thematic content analysis, pre/post evaluation results, and inherent program knowledge were triangulated to make recommendations to sustain the program once the initial funding ends. ^

Asociaciones entre clones y anormalidades morfológicas en ajo

Con el objeto de detectar la influencia del genotipo en la presencia de anormalidades morfológicas, se tomó una muestra de 200 bulbillos de cada uno de los 7 clones de ajo colorado, incluidos en un ensayo experimental en bloques completamente aleatorizados con 4 repeticiones, en un solo ambiente de expresión. En cada clon se computaron las proporciones de bulbos normales, pera, cebollón y doble. En los bulbos normales se midió la distribución de calibres. Se compararon las proporciones de anormalidades entre los clones. Un clon se diferenció (p < 0,05) de los restantes por no poseer malformaciones y presentar un calibre promedio bajo. Utilizando en conjunto la información obtenida, se realizó un análisis de componentes principales y de conglomerado. Se utilizó la distancia euclidiana promedio y el método de ligamiento promedio. Los dos primeros ejes del análisis de componentes principales representaron el 74% de la variación de los datos. La información obtenida permitió reunir 3 grupos de clones por su asociación a calibres y anormalidades morfológicas. El primer grupo formado por un clon sin anormalidades y con mayor proporción de calibre 4 y 5; el segundo, de cuatro clones con presencia de ajo cebollón y el tercero, de dos clones asociados a los bulbos pera, dobles y de calibres 6. Se demostró la influencia del genotipo en la frecuencia de anormalidades morfológicas.

Hacia un enfoque analítico y de políticas para las interacciones entre ciencia, universidad y sociedad en la región latinoamericana

El objetivo de este trabajo es argumentar sobre la importancia del enfoque de redes de conocimiento, generado en el campo de los estudios sociales de la ciencia y la tecnología (CTS), para el análisis de las relaciones entre ciencia, universidad y sociedad. La construcción de procesos interactivos, cooperativos entre actores y el aprendizaje constituyen dimensiones clave para producir y utilizar conocimiento en la mejora del bienestar social de nuestras poblaciones. El trabajo expone brevemente las concepciones que han dominado en las políticas de ciencia y tecnología en la región latinoamericana; se argumenta sobre la importancia de los enfoques de redes de conocimiento y de la perspectiva regional y local al interior de los países, tanto para analizar la generación, intercambio y uso de conocimiento como para el diseño e implementación de políticas públicas de ciencia, tecnología e innovación; se documenta si en las nuevas concepciones de políticas de ciencia, tecnología e innovación en América Latina que destacan la importancia de la inclusión social se está adoptando el enfoque de redes de conocimiento y la perspectiva regional; y, se ofrecen, a manera de conclusiones, algunas argumentaciones sobre el futuro de las relaciones entre universidad y sociedad en lo que al desarrollo científico y tecnológico se refiere.