The impact of poor power quality in solar photovoltaic microgeneration: technical problems and losses of revenue

This paper presents a critical and quantitative analysis of the influence of the Power Quality in grid connected solar photovoltaic microgeneration installations. First are introduced the main regulations and legislation related with the solar photovoltaic microgeneration, in Portugal and Europe. Next are presented Power Quality monitoring results obtained from two residential solar photovoltaic installations located in the north of Portugal, and is explained how the Power Quality events affect the operation of these installations. Afterwards, it is described a methodology to estimate the energy production losses and the impact in the revenue caused by the abnormal operation of the electrical installation. This is done by comparing the amount of energy that was injected into the power grid with the theoretical value of energy that could be injected in normal conditions. The performed analysis shows that Power Quality severally affects the solar photovoltaic installations operation. The losses of revenue in the two monitored installations M1 and M2 are estimated in about 27% and 22%, respectively.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Degradación de efluentes de las industrias del cuero y textil mediante procesos fotocatalíticos heterogéneos empleando la luz solar. Degradation of effluents from the leather and textile industries through heterogeneous photocatalytic processes using sunlight.

El creciente desarrollo de la industria del cuero y textil en nuestro país, y específicamente en la provincia de Córdoba, ha hecho resurgir en los ultimos años una problemática aún no resuelta que es la elevada contaminación de los recursos hídricos. En ambas industrias, la operación de teñido involucra principalmente colorantes de tipo azoico los cuales son "no biodegradables" y se fragmentan liberando aminas aromáticas cancerígenas. Para abordar esta problemática, la fotocatálisis heterogénea aparece como una nueva tecnología que permitiría la completa mineralización de estos colorantes. A través de radiación y un fotocatalizador sólido adecuado se pueden generan radicales libres eficientes para la oxidación de materia orgánica (colorantes) en medio acuoso. En este sentido, se proponen tamices moleculares mesoporosos modificados con metales de transición (MT) como fotocatalizadores potencialmente aptos para la degradación de estos contaminantes. El propósito principal de este proyecto es el diseño, síntesis, caracterización y evaluación de materiales mesoporosos que presenten actividad fotocatalítica ya sea mediante la modificación de su estructura con diversos metales fotosensibles y/o empleándolos como soporte de óxido de titanio. Se pretende evaluar estos materiales en la degradación de colorantes intentando desplazar su fotosensibilidad hacia la radiación visible para desarrollar nuevas tecnologías con menor impacto ambiental y mayor aprovechamiento de la energía solar. Para ello se sintetizarán materiales del tipo MCM-41 modificados con distintos MT tales como Fe, Cr, Co, Ni y Zn mediante incorporación directa del ión metálico o impregnación. Al mismo tiempo, tanto estos últimos materiales como el MCM-41 silíceo serán empleados como soporte de TiO2. Sus propiedades fisicoquímicas se caracterizarán mediante distintas técnicas instrumentales y su actividad fotocatalítica se evaluará en la degradación de colorantes azoicos bajo radiación visible. Se seleccionará el catalizador más eficiente y se estudiarán los diversos factores que afectan el proceso de fotodegradación. Así mismo, el análisis de la concentración del colorante y los productos presentes en el medio en función del tiempo de reacción permitirá inferir sobre la cinética de la decoloración y postular posibles mecanismos de fotodegradación. Con esta propuesta se espera contribuír al desarrollo de un sector industrial importante en nuestra provincia como es el de las industrias del cuero y textil, mediante la generación de nuevas tecnologías que empleen la energía solar para la degradación de sus efluentes (colorantes). En este sentido, se espera desarrollar nuevos materiales optimizados para lograr la mayor eficiencia fotocatalítica. Esto conduciría entonces hacia la remediación de un problema ambiental de alto impacto tanto para nuestra provincia y nuestro país como para la población mundial, como es la contaminación de los recursos hídricos. Finalmente, con este proyecto se contribuirá a la formación de dos doctorandos y un maestrando, cuyos temas de tesis están vinculados con nuestro objeto de estudio. The increasing development of the textile and leather industries in our country, and specifically in Córdoba, has revived an unresolved problem that is the high contamination of water resources. In both industries, the dyeing involves mainly type azoic dyes which are not biodegradable and break releasing carcinogenic aromatic amines. Heterogeneous photocatalysis appears as a new technology that would allow the complete mineralization of these pollutants. Through radiation and a suitable solid it is possible to generate free radicals for efficient oxidation of organic matter (dyes) in aqueous medium. In this respect, mesoporous molecular sieves modified with transition metals are proposed as potential photocatalysts. The main purpose of this project is the synthesis of mesoporous materials having photocatalytic activity for the degradation of dyes. We will try to move their photosensitivity to visible radiation to develop new technologies with lower environmental impact and greater use of solar energy. Materials MCM-41 modified with metals (Fe, Cr, Co, Ni and Zn) will be synthesized by direct incorporation or impregnation. These materials and the siliceous MCM-41 will be then employed as support of TiO2. The materials will be evaluated in the photocatalytic degradation of azoic dyes under visible radiation. The influence of different factors on the photodegradation proccess will be studied. Kinetic studies will be carried out and a possible reaction way will be proposed. Thus, this work will contribute to the advancement of an important industrial sector and the remediation of an environmental problem with high impact for our province and our country. Moreover, this proyect will contribute to the development of two doctoral tesis and one magister tesis which are vinculated with our study subject.

Potentially viable solar powered appliances cooling and distillation

Stand alone solar powered refrigeration and water desalination, two of the most popular and sought after applications of solar energy systems, have been selected as the topic of research for the works presented in this thesis. The water desalination system based on evaporation and condensation was found to be the most suitable one to be powered by solar energy. It has been established that highoutput fast-response solar heat collectors used to achieve high rates of evaporation and reliable solar powered cooling system for faster rates of condensation are the most important factors in achieving increased outputs in solar powered desalination systems. Comprehensive reviews of Solar powered cooling/refrigeration and also water desalination techniques have been presented. In view of the fact that the Institute of Technology, Sligo has a well-established long history of research and development in the production of state of the art high-efficiency fast-response evacuated solar heat collectors it was decided to use this know how in the work described in this thesis. For this reason achieving high rates of evaporation was not a problem. It was, therefore, the question of the solar powered refrigeration that was envisaged to be used in the solar powered desalination tofacilitate rapid condensation of the evaporated water that had to be addressed first. The principles of various solar powered refrigeration techniques have also been reviewed. The first step in work on solar powered refrigeration was to successfully modify a conventional refrigerator working on Platen-Munters design to be powered by highoutput fast-response evacuated solar heat collectors. In this work, which was the first ever successful attempt in the field, temperatures as low as —19°C were achieved in the icebox. A new approach in the use of photovoltaic technology to power a conventional domestic refrigerator was also attempted. This was done by modifying a conventional domestic refrigerator to be powered by photovoltaic panels in the most efficient way. In the system developed and successfully tested in this approach, the power demand has been reduced phenomenally and it is possible to achieve 48 hours of cooling power with exposure to just 7 hours of sunshine. The successful development of the first ever multi-cycle intermittent solar powered icemaker is without doubt the most exciting breakthrough in the work described in this thesis. Output of 74.3kg of ice per module with total exposure area of 2.88 m2, or 25.73kg per m2, per day is a major improvement in comparison to about 5-6kg of ice per m2 per day reported for all the single cycle intermittent systems. This system has then become the basis for the development of a new solar powered refrigeration system with even higher output, named the “composite” system described in this thesis. Another major breakthrough associated with the works described in this thesis is the successful development and testing of the high-output water desalination system. This system that uses a combination of the high-output fast-response evacuated solar heat collectors and the multi-cycle icemaker. The system is capable of producing a maximum of 141 litres of distilled water per day per module which has an exposure area of 3.24m2, or a production rate of 43.5 litres per m2 per day. Once again when this result is compared to the reported daily output of 5 litres of desalinated water per m per day the significance of this piece of work becomes apparent. In the presentation of many of the components and systems described in this thesis CAD parametric solid modelling has been used instead of photographs to illustrate them more clearly. The multi-cycle icemaker and the high-output desalination systems are the subject of two patent applications.

Left Atrial Volume Index and Prediction of Events in Acute Coronary Syndrome: Solar Registry

Background: According to some international studies, patients with acute coronary syndrome (ACS) and increased left atrial volume index (LAVI) have worse long-term prognosis. However, national Brazilian studies confirming this prediction are still lacking. Objective: To evaluate LAVI as a predictor of major cardiovascular events (MCE) in patients with ACS during a 365-day follow-up. Methods: Prospective cohort of 171 patients diagnosed with ACS whose LAVI was calculated within 48 hours after hospital admission. According to LAVI, two groups were categorized: normal LAVI (≤ 32 mL/m2) and increased LAVI (> 32 mL/m2). Both groups were compared regarding clinical and echocardiographic characteristics, in- and out-of-hospital outcomes, and occurrence of ECM in up to 365 days. Results: Increased LAVI was observed in 78 patients (45%), and was associated with older age, higher body mass index, hypertension, history of myocardial infarction and previous angioplasty, and lower creatinine clearance and ejection fraction. During hospitalization, acute pulmonary edema was more frequent in patients with increased LAVI (14.1% vs. 4.3%, p = 0.024). After discharge, the occurrence of combined outcome for MCE was higher (p = 0.001) in the group with increased LAVI (26%) as compared to the normal LAVI group (7%) [RR (95% CI) = 3.46 (1.54-7.73) vs. 0.80 (0.69-0.92)]. After Cox regression, increased LAVI increased the probability of MCE (HR = 3.08, 95% CI = 1.28-7.40, p = 0.012). Conclusion: Increased LAVI is an important predictor of MCE in a one-year follow-up.

Production and quality of cotton fibers in relation to solar radiation

The present paper refers to a research work carried out at the Dept. of Agriculture and Horticulture of ESALQ, University of São Paulo, in Piracicaba, State of São Paulo (latitude 22º42'S, longitude 47º33' WG and altitude 546 m). Sowing at different times and using artificial cover, an attempt was made to evaluate the behavior of cultivar IAC 17 of cotton (Gossypium hirsutum L.) as to production and quality of fiber relating to incident solar radiation. Incident solar radiation, as well as insolation during the trial period, were tabulated and compared with yelds and agricultural and technological characters of fibers. The treatment under cover showed a mean level of incident solar radiation equivalent to less than 20% of that at clear sky, causing a decrease in cotton production and in the agricultural and technological characters of fibers.

The solar year of the Mayas at Quirigua, Guatemala / by J. Eric Thompson, Assistant Curator of Central and South American Archaeology; 2 text-figures; Berthold Laufer, Curator, Department of Anthropology, editor.

v.17:no.4(1932)

The solar year of the Mayas at Quirigua, Guatemala / by J. Eric Thompson, Assistant Curator of Central and South American Archaeology; 2 text-figures; Berthold Laufer, Curator, Department of Anthropology, editor.

v.17:no.4(1932)

Effective exposure to solar UV in building workers: influence of local and individual factors.

Excessive exposure to solar UV light is the main cause of skin cancers in humans. UV exposure depends on environmental as well as individual factors related to activity. Although outdoor occupational activities contribute significantly to the individual dose received, data on effective exposure are scarce and limited to a few occupations. A study was undertaken in order to assess effective short-term exposure among building workers and characterize the influence of individual and local factors on exposure. The effective exposure of construction workers in a mountainous area in the southern part of Switzerland was investigated through short-term dosimetry (97 dosimeters). Three altitudes, of about 500, 1500 and 2500 m were considered. Individual measurements over 20 working periods were performed using Spore film dosimeters on five body locations. The postural activity of workers was concomitantly recorded and static UV measurements were also performed. Effective exposure among building workers was high and exceeded occupational recommendations, for all individuals for at least one body location. The mean daily UV dose in plain was 11.9 SED (0.0-31.3 SED), in middle mountain 21.4 SED (6.6-46.8 SED) and in high mountain 28.6 SED (0.0-91.1 SED). Measured doses between workers and anatomical locations exhibited a high variability, stressing the role of local exposure conditions and individual factors. Short-term effective exposure ranged between 0 and 200% of ambient irradiation, indicating the occurrence of intense, subacute exposures. A predictive irradiation model was developed to investigate the role of individual factors. Posture and orientation were found to account for at least 38% of the total variance of relative individual exposure, and were also found to account more than altitude on the total variance of effective daily exposures. Targeted sensitization actions through professional information channels and specific prevention messages are recommended. Altitude outdoor workers should also benefit from preventive medical examination.

Temporal variability and trends of the downward solar radiation over Europe during the 20th century, with regional focus in the dimming/brightening phenomena on the Iberian Peninsula

Proyecto de investigación elaborado a partir de una estancia en el Institute for Atmospheric and Climate Science, a Alemanya, entre 2010 y 2012. La radiación solar que alcanza la superficie terrestre es un factor clave entre los procesos que controlan el clima de la Tierra, dado el papel que desempeñan en el balance energético y el ciclo hidrológico. Establecer su contribución al cambio climático reciente supone una gran dificultad debido a la complejidad de los procesos implicados, la gran cantidad de información requerida, y la incertidumbre de las bases de datos disponibles en la actualidad. Así, el objetivo principal del proyecto ha consistido en generar una base de datos de insolación incluyendo las series más largas (desde finales del siglo XIX) disponibles en toda Europa. Esta base de datos complementa para nuestro continente el Global Energy Balance Archive (GEBA) que mantiene y gestiona el grupo que ha acogido al receptor de la ayuda postdoctoral, y permite extender espacial (especialmente en países del sur de Europa) y temporalmente las series climáticas disponibles de mediciones de irradiancia solar. Como la insolación es un proxy de la irradiancia solar, el proyecto actual también ha tratado de calibrar de forma exhaustiva ambas variables, a fin de generar una nueva base de datos reconstruida de esta segunda variable que esté disponible desde finales del siglo XIX en Europa. Un segundo objetivo del proyecto ha consistido en continuar trabajando a escala de mayor detalle sobre la Península Ibérica, con el fin de proporcionar una mejor comprensión del fenómeno del “global dimming/brightening” y su impacto en el ciclo hidrológico y balance energético. Finalmente, un tercer objetivo del presente proyecto postdoctoral ha consistido en continuar estudiando los posibles ciclos semanales a gran escala de diferentes variables climáticas, línea de investigación de interés para la detección de posibles efectos de los aerosoles antrópicos en el clima a escalas temporales breves, y consecuentemente estrechamente vinculado al fenómeno del “global dimming/brightening”.

High-energy gamma-ray emission from microquasars: LS 5039 and LS I+61303

The possible associations between the microquasars LS 5039 and LS I +61 303 and the EGRET sources 3EG J1824-1514 and 3EG J0241+6103 suggest that microquasars could also be sources of high-energy gamma-rays. In this work, we present a detailed numerical inverse Compton (IC) model, based on a microquasar scenario, that reproduces the high-energy gamma-ray spectra and variability observed by EGRET for the mentioned sources. Our model considers a population of relativistic electrons entrained in a cylindrical inhomogeneous jet that interact through IC scattering with both the radiation and the magnetic fields.

The Coordinated Radio and Infrared Survey for High-Mass Star Formation (The CORNISH Survey). I. Survey Design

We describe the motivation, design, and implementation of the CORNISH survey, an arcsecondresolution radio continuum survey of the inner galactic plane at 5 GHz using the Very Large Array (VLA). It is a blind survey coordinated with the northern SpitzerGLIMPSE I region covering 10° and jbj < 1° at similar resolution. We discuss in detail the strategy that we employed to control the shape of the synthesised beam across this survey, which covers a wide range of fairly low declinations. Two snapshots separated by 4 h kept the beam elongation to less that 1.5 over 75% of the survey area and less than 2 over 98% of the survey. The prime scientific motivation is to provide an unbiased survey for ultra-compact H II regions to study this key phase in massive star formation. A sensitivity around 2 mJy will allow the automatic distinction between radio-loud and radio-quiet midIR sources found in the Spitzersurveys. This survey has many legacy applications beyond star formation, including evolved stars, active stars and binaries, and extragalactic sources. The CORNISH survey for compact ionized sources complements other Galactic plane surveys that target diffuse and nonthermal sources, as well as atomic and molecular phases to build up a complete picture of the interstellar medium in the Galaxy.

INTEGRAL and XMM-Newton observations towards the unidentified MeV source GRO J1411-64.

The COMPTEL unidentified source GRO J1411-64 was observed by INTEGRAL, and its central part, also by XMM-Newton. The data analysis shows no hint for new detections at hard X-rays. The upper limits in flux herein presented constrain the energy spectrum of whatever was producing GRO J1411-64, imposing, in the framework of earlier COMPTEL observations, the existence of a peak in power output located somewhere between 300-700 keV for the so-called low state. The Circinus Galaxy is the only source detected within the 4$\sigma$ location error of GRO J1411-64, but can be safely excluded as the possible counterpart: the extrapolation of the energy spectrum is well below the one for GRO J1411-64 at MeV energies. 22 significant sources (likelihood $> 10$) were extracted and analyzed from XMM-Newton data. Only one of these sources, XMMU J141255.6-635932, is spectrally compatible with GRO J1411-64 although the fact the soft X-ray observations do not cover the full extent of the COMPTEL source position uncertainty make an association hard to quantify and thus risky. The unique peak of the power output at high energies (hard X-rays and gamma-rays) resembles that found in the SED seen in blazars or microquasars. However, an analysis using a microquasar model consisting on a magnetized conical jet filled with relativistic electrons which radiate through synchrotron and inverse Compton scattering with star, disk, corona and synchrotron photons shows that it is hard to comply with all observational constrains. This and the non-detection at hard X-rays introduce an a-posteriori question mark upon the physical reality of this source, which is discussed in some detail.