Benchmarking a modified version of the civ3 nonrelativistic atomic-structure code within Na-like-tungsten R -matrix calculations

In this work we explore the validity of employing a modified version of the nonrelativistic structure code civ3 for heavy, highly charged systems, using Na-like tungsten as a simple benchmark. Consequently, we present radiative and subsequent collisional atomic data compared with corresponding results from a fully relativistic structure and collisional model. Our motivation for this line of study is to benchmark civ3 against the relativistic grasp0 structure code. This is an important study as civ3 wave functions in nonrelativistic R-matrix calculations are computationally less expensive than their Dirac counterparts. There are very few existing data for the W LXIV ion in the literature with which we can compare except for an incomplete set of energy levels available from the NIST database. The overall accuracy of the present results is thus determined by the comparison between the civ3 and grasp0 structure codes alongside collisional atomic data computed by the R-matrix Breit-Pauli and Dirac codes. It is found that the electron-impact collision strengths and effective collision strengths computed by these differing methods are in good general agreement for the majority of the transitions considered, across a broad range of electron temperatures.

The Transverse Crack Tension test revisited: An experimental and numerical study

Several problems arise when measuring the mode II interlaminar fracture toughness using a Transverse Crack Tension specimen; in particular, the fracture toughness depends on the geometry of the specimen and cannot be considered a material parameter. A preliminary experimental campaign was conducted on TCTs of different sizes but no fracture toughness was measured because the TCTs failed in an unacceptable way, invalidating the tests. A comprehensive numerical and experimental investigation is conducted to identify the main causes of this behaviour and a modification of the geometry of the specimen is proposed. It is believed that the obtained results represent a significant contribution in the understanding of the TCT test as a mode II characterization procedure and, at the same time, provide new guidelines to characterize the mode II crack propagation under tensile loads.

On the statistics of transverse permeability of randomly distributed fibers

An RVE–based stochastic numerical model is used to calculate the permeability of randomly generated porous media at different values of the fiber volume fraction for the case of transverse flow in a unidirectional ply. Analysis of the numerical results shows that the permeability is not normally distributed. With the aim of proposing a new understanding on this particular topic, permeability data are fitted using both a mixture model and a unimodal distribution. Our findings suggest that permeability can be fitted well using a mixture model based on the lognormal and power law distributions. In case of a unimodal distribution, it is found, using the maximum-likelihood estimation method (MLE), that the generalized extreme value (GEV) distribution represents the best fit. Finally, an expression of the permeability as a function of the fiber volume fraction based on the GEV distribution is discussed in light of the previous results.

Sedimentology, structure and age estimate of five continental slope submarine landslides, eastern Australia

Sedimentological and accelerator mass spectrometry (AMS) 14C data provide estimates of the structure and age of five submarine landslides (∼0.4–3 km3) present on eastern Australia's continental slope between Noosa Heads and Yamba. Dating of the post-slide conformably deposited sediment indicates sediment accumulation rates between 0.017 m ka–1 and 0.2 m ka–1, which is consistent with previous estimates reported for this area. Boundary surfaces were identified in five continental slope cores at depths of 0.8 to 2.2 m below the present-day seafloor. Boundary surfaces present as a sharp colour-change across the surface, discernible but small increases in sediment stiffness, a slight increase in sediment bulk density of 0.1 g cm–3, and distinct gaps in AMS 14C ages of at least 25 ka. Boundary surfaces are interpreted to represent a slide plane detachment surface but are not necessarily the only ones or even the major ones. Sub-bottom profiler records indicate that: (1) the youngest identifiable sediment reflectors upslope from three submarine landslides terminate on and are truncated by slide rupture surfaces; (2) there is no obvious evidence for a post-slide sediment layer draped over, or burying, slide ruptures or exposed slide detachment surfaces; and (3) the boundary surfaces identified within the cores are unlikely to be near-surface slide surfaces within an overall larger en masse dislocation. These findings suggest that these submarine landslides are geologically recent (<25 ka), and that the boundary surfaces are either: (a) an erosional features that developed after the landslide, in which case the boundary surface age provides a minimum age for the landslide; or (b) detachment surfaces from which slabs of near-surface sediment were removed during landsliding, in which case the age of the sediment above the boundary surface indicates the approximate age of landsliding. While an earthquake-triggering mechanism is favoured for the initiation of submarine landslides on the eastern Australian margin, further evidence is required to confirm this interpretation.

Settlement Duration and Materiality:Formal Chronological Models for the Development of Barnhouse, a Grooved Ware Settlement in Orkney

Radiocarbon dating and Bayesian chronological modelling, undertaken as part of the investigation by the Times of Their Lives project into the development of Late Neolithic settlement and pottery in Orkney, has provided precise new dating for the Grooved Ware settlement of Barnhouse, excavated in 1985–91. Previous understandings of the site and its pottery are presented. A Bayesian model based on 70 measurements on 62 samples (of which 50 samples are thought to date accurately the deposits from which they were recovered) suggests that the settlement probably began in the later 32nd century cal bc (with Houses 2, 9, 3 and perhaps 5a), possibly as a planned foundation. Structure 8 – a large, monumental structure that differs in character from the houses – was probably built just after the turn of the millennium. Varied house durations and replacements are estimated. House 2 went out of use before the end of the settlement, and Structure 8 was probably the last element to be abandoned, probably during the earlier 29th century cal bc. The Grooved Ware pottery from the site is characterised by small, medium-sized, and large vessels with incised and impressed decoration, including a distinctive, false-relief, wavy-line cordon motif. A considerable degree of consistency is apparent in many aspects of ceramic design and manufacture over the use-life of the settlement, the principal change being the appearance, from c. 3025–2975 cal bc, of large coarse ware vessels with uneven surfaces and thick applied cordons, and of the use of applied dimpled circular pellets. The circumstances of new foundation of settlement in the western part of Mainland are discussed, as well as the maintenance and character of the site. The pottery from the site is among the earliest Grooved Ware so far dated. Its wider connections are noted, as well as the significant implications for our understanding of the timing and circumstances of the emergence of Grooved Ware, and the role of material culture in social strategies.

Design and Implementation of a Low Cost Virtual Rugby Decision Making Interactive

The paper describes the design and implementation of a novel low cost virtual rugby decision making interactive for use in a visitor centre. Original laboratory-based experimental work in decision making in rugby, using a virtual reality headset [1] is adapted for use in a public visitor centre, with consideration given to usability, costs, practicality and health and safety. Movement of professional rugby players was captured and animated within a virtually recreated stadium. Users then interact with these virtual representations via use of a lowcost sensor (Microsoft Kinect) to attempt to block them. Retaining the principles of perception and action, egocentric viewpoint, immersion, sense of presence, representative design and game design the system delivers an engaging and effective interactive to illustrate the underlying scientific principles of deceptive movement. User testing highlighted the need for usability, system robustness, fair and accurate scoring, appropriate level of difficulty and enjoyment.

Fast and sensitive aflatoxin B1 and total aflatoxins ELISAs for analysis of peanuts, maize and feed ingredients

Aflatoxins are a group of carcinogenic compounds produced by Aspergillus fungi that can grow on different agricultural crops. Both acute and chronic exposure to these mycotoxins can cause serious illness. Due to the high occurrence of aflatoxins in crops worldwide fast and cost-effective analytical methods are required for the identification of contaminated agricultural commodities before they are processed into final products and placed on the market. In order to provide new tools for aflatoxin screening two prototype fast ELISA methods: one for the detection of aflatoxin B₁ and the other for total aflatoxins were developed. Seven monoclonal antibodies with unique high sensitivity and at the same time good cross-reactivity profiles were produced. The monoclonal antibodies were characterized and two antibodies showing IC₅₀ of 0.037 ng/mL and 0.031 ng/mL for aflatoxin B₁ were applied in simple and fast direct competitive ELISA tests. The methods were validated for peanut matrix as this crop is one of the most affected by aflatoxin contamination. The detection capabilities of aflatoxin B₁ and total aflatoxins ELISAs were 0.4 μg/kg and 0.3 μg/kg for aflatoxin B₁, respectively, which are one of the lowest reported values. Total aflatoxins ELISA was also validated for the detection of aflatoxins B₂, G₁ and G₂. The application of the developed tests was demonstrated by screening 32 peanut samples collected from the UK retailers. Total aflatoxins ELISA was further applied to analyse naturally contaminated maize porridge and distiller's dried grain with solubles samples and the results were correlated with these obtained by UHPLC-MS/MS method.

Banana and abaca fiber-reinforced plastic composites obtained by rotational molding process

Natural fibers can be used in rotational molding process to obtain parts with improved mechanical properties. Different approaches have been followed in order to produce formulations containing banana or abaca fiber at 5% weight, in two- and three-layer constructions. Chemically treated abaca fiber has also been studied, causing some problems in processability. Fibers used have been characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), optical microscopy, and single-fiber mechanical tests. Rotomolded parts have been tested for tensile, flexural, and impact properties, demonstrating that important increases in elastic modulus are achieved with these fibers, although impact properties are reduced. © 2013 Copyright Taylor and Francis Group, LLC.

Global efficiency of innovative rotational mold directly heated by thermal fluid

The article is focused on analysis of global efficiency of new mold for rotational molding of plastic parts, being directly heated by thermal fluid. The overall efficiency is based on several items such as reduction of cycle time, better uniformity of heating-cooling and low energy consumption. The new tool takes advantage of additive fabrication and electroforming for making the optimal manifold and cavity shell of the mold. Experimental test of a prototype mold was carried out on an experimental rotational molding machine, developed for this purpose, measuring wall temperature, and internal air temperature, with and without plastic material inside. Results were compared with conventional mold heated into an oven and to theoretical simulations done by Computational Fluid Dynamic software (CFD). The analysis represents considerable improvement of cycle time related to conventional methods (heated by oven) and better thermal uniformity to conventional procedures by direct heating of oil with external channels. In addition to thermal analysis an energetic efficiency study was done. POLYM. ENG. SCI., 52:1998-2005, 2012. © 2012 Society of Plastics Engineers Copyright © 2012 Society of Plastics Engineers.

Internal cooling in rotational molding-A review

Rotational molding suffers from a relatively long cycle time, which hampers more widespread growth of the process. During each cycle, both the polymer and mold must be heated from room temperature to above polymer melting temperature and subsequently cooled to room temperature. The cooling time in this process is relatively long due to the poor thermal conductivity of plastics. Although rapid external cooling is possible, internal cooling rates are the major limitation. This causes the process to be uneconomical for large production runs of small parts. Various researchers have strived to minimize cycle times by applying various internal cooling procedures. This article presents a review of these methods, including computer simulations and practical investigations published to date. The effects of cooling rate on the morphology, shrinkage, warpage, and impact properties of rotationally molded polyolefins are also highlighted. In general, rapid and symmetrical cooling across the mold results in smaller spherulite size, increased mechanical properties and less potential warpage or distortion in moldings. POLYM. ENG. SCI., 2011. ©2011 Society of Plastics Engineers.

Glass fibre-reinforced polyethylene composites in rotational moulding

Fibre-reinforced mouldings are of growing interest to the rotational moulding industry due to their outstanding price performance ratio. However, a particular problem that arises when using reinforcements in this process is that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this paper we report on studies to incorporate, short glass fibres into rotationally moulded parts. Four different approaches were investigated; direct addition of fibre in between two powder shots, addition of a layer of pre-compounded polyethylene-glass fibre pellets between two powder shots, addition of a layer of pre-compounded polyethylene-glass fibre powder between two powder shots and a single layer of glass-reinforced, pre-compounded powder. Results indicate that pre-compounding is necessary to gain performance enhancement and the single layer part made from glass-reinforced, pre-compounded powder exhibited the highest tensile and flexural modulus.

Rotary moulding of ceramic hollow wares

A novel processing method for the fast and economic production of hollow ceramic components has been developed by combining in situ coagulation moulding with a modified version of the technique of rotary moulding[Binner, J. G. P., Al-Dawery, I. A., Tari, G. and Yan, Y., Rotary casting technique. UK Patent application No. 0506349.0, March 2005], the latter being adapted from the polymer industry. The process was found to require a high solids content suspension, hence development work was performed in this direction though in the end a new, commercial suspension was utilised. Of the three forming routes of gel casting, direct coagulation casting and in situ coagulation moulding, the latter was found to be the most promising for the new process of rotary moulding of ceramics. Due to the low value of clay-based ceramics, a new low cost coagulant was identified and the effect of lactone concentration and temperature on setting time determined. Following substantial optimisation work, it was found that a two-speed approach to multi-axial rotation was the most successful; medium sized cream jugs could be produced in just 7 min. With respect to mould materials, the porous resin normally used for pressure casting of sanitary ware was found to be the best option, though since this is quite expensive conventional plaster-of-paris moulds were found to be a suitable material to enable companies, particularly SMEs, to become familiar with the technology whilst avoiding high costs for trials. The processed articles could be successfully fired and glazed using gas-fired kilns with no sign of any black cores. Major advantages of the process include the ability to precisely calculate the amount of ceramic slip required, eliminating either slip wastage or the need to pour used slip back into the virgin material as currently happens with slip casting. In addition, since the precursor suspension has a very high solids content, the time and energy required to dry the green product and associated moulds has been considerably reduced. © 2008 Elsevier Ltd. All rights reserved.

The adaption of microwave heating to the rotational moulding process

This paper details the results from a large European Union rotomoulding research project on the adaptation and development of industrial microwave oven technology to the rotational moulding process. Following computer modelling, an industrial scale microwave oven was specifically designed, manufactured and attached to the drop-arm of a convention rotational moulding machine where extensive moulding trials were carried out. The design and development of the microwave oven and test mould, together with the savings in terms of energy efficiency and mould heating rate that were achieved are discussed.

Characterisation of polyethylene powders for rotational moulding and effect of powder size and shape on densification behaviour

The particle size, shape and distribution of a range of rotational moulding polyethylenes (PEs) ground to powder was investigated using a novel visual data acquisition and analysis system (TP Picture®), developed by Total Petrochemicals. Differences in the individual particle shape factors of the powder samples were observed and correlations with the grinding conditions were determined. When heated, the bubble dissolution behaviour of the same powders was investigated and the shape factor correlated with densification rate, bubble size and bubble distribution.

Study into the densification behaviour of polyethylenes for rotational moulding

The melting and densification behaviour of a range of Polyethylenes (PEs) produced from 2 different catalysts, Ziegler-Natta and Metallocene types, were investigated using a novel visual data acquisition and analysis system (TP Picture®), developed by Total Petrochemicals Research Feluy [1]. Differences in the dissolution behaviour of the bubbles were observed and correlations with the material density, densification rate, bubble size / distribution and MFI were determined.