Ca-amendement and tillage: medium term synergies for improving key soil properties of acid soils. Soil and tillage research, 134: 195-206

Ca-amendments are routinely applied to improve acid soils, whilst no-tillage (NT) has been widely recommended in soils where traditional tillage (TT) has led to losses of organic matter. However, the potential interactions between the two treatments are only partially known. Our study was conducted on an annual forage crop agrosystem with a degraded Palexerult soil located in SW Spain, in order to assess if the combination of NT plus a Ca-amendment provides additional benefits to those of their separate use. To this end we analysed the effects of four different combinations of tillage and Ca-amendment on selected key soil properties, focusing on their relationships. The experimental design was a split-plot with four replicates. The main factor was tillage (NT versus TT) and the second factor was the application or not of a Ca-amendment, consisting of a mixture of sugar foam (SF) and red gypsum (RG). Soil samples were collected from 3 soil layers down to 50 cm after four years of treatment (2009). The use of the Ca-amendment improved pH and Al-toxicity down to 25 cm and increased exchangeable Ca2+ down to 50 cm, even under NT due to the combined effect of SF and RG. Both NT and the Ca-amendment had a beneficial effect on total organic carbon (TOC), especially on particulate organic carbon (POC), in the 0–5 cm layer, with the highest contents observed when both practices were combined. Unlike NT, the Ca-amendment failed to improve soil aggregation in spite of the carbon supplied. This carbon was not protected within the stable aggregates in the medium term, making it more susceptible to mineralization. We suggest that the fraction of Al extracted by oxalate from solid phase (AlOxa-Cu-K) and the glomalin-related soil proteins (GRSPs) are involved in the accumulation of carbon within water stable aggregates, probably through the formation of non-toxic stable Al-OM compounds, including those formed with GRSPs. NT alone decreased AlK in the 0–5 cm soil layer, possibly by increasing POC, TOC and GRSPs, which were observed to play a role in reducing Al toxicity. From our findings, the combination of NT and Ca-amendment appears to be the best management practice to improve chemical and physical characteristics of acid soils degraded by tillage.

Estudio sobre la durabilidad de los nuevos tipos de cemento para la evaluación del comportamiento de morteros y hormigones frente a la agresión química de los sulfatos y del agua de mar

Esta investigación ha sido desarrollada para analizar la influencia de las características específicas de los nuevos cementos en el comportamiento expansivo originado durante cinco años por el ataque externo por sulfatos o agua de mar, y para estudiar la validez de diversos métodos de ensayo aplicables para evaluar la resistencia de los conglomerantes a los sulfatos o al agua de mar. Se han determinado las características químicas y mecánicas de los quince cementos seleccionados en el estudio (su contenido de yeso, tipo y cantidad de adiciones, contenidos de C3A y C4AF) para examinar la relación entre estos parámetros y su durabilidad frente al ataque por sulfatos. Se han llevado a cabo ensayos para evaluar la resistencia a sulfatos sobre probetas de mortero fabricadas con los quince cementos comunes seleccionados de muy distintos tipos, la mayoría de ellos resistentes a sulfatos conforme a la norma UNE-EN 197-1. Por cada tipo de cemento se fabricaron probetas de mortero para la realización de ensayos acelerados usando Na2SO4 como medio agresivo según la norma ASTM C 1012 manteniendo esas condiciones de exposición durante dos años. En paralelo se fabricaron otras series de probetas idénticas, que fueron conservadas en agua de mar y en agua saturada en cal (como patrón de un medio no agresivo) durante el mismo plazo. Adicionalmente estos cementos fueron evaluados conforme a los procedimientos de ensayo acelerado de la norma ASTM C 452 y del ensayo de Koch y Steinegger. También se fabricaron otras series de probetas de 40x40x160 mm (adoptando una relación a/c=0,5 y la composición arena:cemento definida en la norma UNE-EN 196-1). Durante cinco años de exposición en las tres condiciones de conservación establecidas (sulfatos, agua de mar y agua patrón) se han efectuado ensayos para determinar la resistencia a compresión y el deterioro superficial de las probetas de mortero. Ninguno de los conglomerantes fue mezclado inicialmente con yeso para acelerar el ataque ni se establecieron otras condiciones no realísticas en la fabricación de los morteros Se ha analizado el comportamiento durable de los cementos tanto frente al ataque por sulfatos como por agua de mar. Para la evaluación se han tomado en consideración las variaciones de contenido en C3A, los tipos y proporciones de los constituyentes (adiciones puzolánicas, escorias de horno alto, caliza …) con el mismo tipo de clínker en algunos casos. Se ha procedido a evaluar la validez de los límites de aceptación establecidos en cada uno de los ensayos acelerados para determinar la resistencia a sulfatos y valorar su idoneidad en los nuevos cementos, y se ha propuesto un método de ensayo acelerado recomendable para discriminar cementos resistentes y no resistentes a sulfatos. A la edad final de los tres tipos de exposición han sido correlacionados los parámetros relativos a la degradación superficial, pérdida de resistencia y expansión lineal de las probetas con las características de los cementos y los productos expansivos analizados mediante difracción de rayos X, con objeto de poder redefinir las características recomendables exigibles a los cementos resistentes a sulfatos o al agua de mar. Experimental research has been performed to relate specific cement characteristics to expansion due to sulfate or sea water attack during five years, and to study different test methods suitability for sulfate and marine resistance. Chemical and mechanical characteristics were studied to determine the variation in properties of selected cements (SO3 content, type and amount of additions, C3A, and C4AF content) and examine relationships between these characteristics and the results of sulfate resistance. Sulfate resistance testing have been performed on mortar specimens prepared from fifteen cement types of statistically diverse chemical composition, most of them with sulfate resistant properties according to European standard EN 197-1 Mortar specimens testing using Na2SO4 as the aggressive medium according to ASTM C 1012 was performed using each cement; identical specimens were also stored in sea water, and in lime saturated water (blank condition), up to two years age. Additionally these cements were tested conforming to ASTM C 452 and Koch and Steinegger test. Mortar specimens of 40x40x160 mm were also moulded (with w/c ratio and cement:sand composition of EN 196-1). Compressive strength of these mortar specimens have been tested during five years of immersion in a sulfate solution and also in seawater (and in lime saturated water, as a blank condition), and external damage and have been analyzed. None of the prepared mortars was blended with gypsum or any other nonrealistic condition. Durability behaviour in sulfate resistant common cements conforming to EN 197-1 exposed to sulfate attack was evaluated, and also the correlation between sulfate resistance and seawater resistance has been studied. Different C3A contents, variable types and proportioning of constituents (limestone, pozzolanic additions, blastfurnace slag ...) with or without the same clinker type were investigated. Recommended acceptance limits for sulfate resistance of cements concerning to each used test method were evaluated in order to explore their suitability. A new accelerated method has been recommended to provide a meaningful discrimination between sulfate resistant or non-sulfate resistant cements. Relationships between cement characteristics, degradation, expansive products obtained by X-ray diffraction techniques, strength loss and maximum expansion after applied storage treatments, were correlated at final age, to redefine cement characteristics for sulfate resistant and marine resistant Portland cement.

New Plaster Composite with Mineral Wool Fibres from CDW Recycling

Over the last decade the intense activity of the building sector has generated large quantities of construction and demolition waste (CDW). In particular, in Europe around 890 million tons of CDW is generated every year; however, only 50% of them are recycled. In Spain, over the last years 40 millions of tons of construction and demolition waste have been generated. On the other hand, since the implementation of the Technical Building Code regulation the use of mineral wools as building insulation materials has become a widespread solution in both rehabilitation and new construction works, and because of that, this kind of insulation waste is increasing. This research analyzes the potential of a new composite (gypsum and fiber waste) including several mineral wools waste into a plaster matrix. For this purpose, an experimental plan, characterizing the physical and mechanical behaviour as well as the Shore C hardness of the new composite, was elaborated fulfilling UNE Standards.

Amelioration of a degraded acid soil from SW Spain by no-tillage and Ca-amendment

En los suelos, el exceso de acidez lleva asociado deficiencias en ciertos nutrientes y una alta disponibilidad de aluminio, tóxico para los cultivos propios del ambiente mediterráneo. Su laboreo, provoca la pérdida de materia orgánica (MO), deteriora su estructura y reduce la actividad biológica, provocando en última instancia una menor calidad del suelo. Es de esperar pues que cuando se labran suelos ácidos, sus problemáticas particulares tiendan a agravarse. En nuestra zona de estudio, la “raña” de Cañamero (Extremadura, España), predominan los suelos muy ácidos y degradados por un laboreo inadecuado. Las rañas constituyen amplias plataformas casi horizontales, con unos suelos muy viejos (Palexerults), que se caracterizan por tener el complejo de cambio dominado por el aluminio, y un pH ácido que decrece en profundidad. Poseen un potente horizonte Bt rico en arcillas caoliníticas, que propicia que en periodos con exceso de lluvia, se generen capas colgadas de agua cercanas a la superficie. En torno a los años 1940’s estos suelos, que previamente sostenían un alcornocal, o su matorral de sustitución, se pusieron en cultivo. El laboreo aceleró la mineralización de la materia orgánica, agravó los problemas derivados del exceso de acidez y condujo al abandono de los campos cultivados por falta de productividad. Para recuperar la calidad de estos suelos degradados y obtener unos rendimientos compatibles con su uso agrícola es necesario, por un lado, aplicar enmiendas que eleven el pH y reduzcan la toxicidad del aluminio y, por otro, favorecer el incremento en el contenido en MO. En 2005 se implantó en esta raña un ensayo de campo para estudiar la influencia del no laboreo y de la utilización de una enmienda cálcica en parámetros relacionados con la calidad del suelo en un cultivo forrajero. El diseño experimental fue en parcelas divididas con cuatro repeticiones donde el factor principal fue el tipo de laboreo, no laboreo (NL) frente a laboreo convencional (LC), y el factor secundario el uso o no de una enmienda cálcica. La enmienda consistió básicamente en una mezcla de espuma de azucarería y yeso rojo y se incorporó al comienzo del ensayo hasta los 7 cm de profundidad. Desde el comienzo del ensayo el NL influyó positivamente en el contenido de carbono orgánico total (COT) y particulado (COP), mientras que la enmienda tuvo una ligera influencia al principio del ensayo en ambos pero su efecto positivo se desvaneció con el paso del tiempo. Los mayores contenidos en COT y POC se observaron cuando se combinó el NL con la enmienda. La enmienda incrementó con rapidez el pH, y el Ca, y disminuyó el contenido en aluminio hasta una profundidad de 50 cm, incluso en NL, y mejoró ligeramente la agregación del suelo. El NL por sí solo, gracias al aumento en POC, TOC y las proteínas del suelo relacionadas con la glomalina (PSRG), que son capaces de formar compuestos estables no tóxicos con el aluminio, también contribuyó a la reducción de la toxicidad de aluminio en la capa más superficial. Cuando en las campañas con exceso de precipitaciones se generaron capas colgadas de agua próximas a la superficie, el NL generó unas condiciones más favorables para la germinación y desarrollo del cultivo, resultando en una producción más alta que el LC. A ello contribuyó la mayor capacidad de almacenamiento de agua y la mayor transmisividad de esta hacia abajo, en la capa más superficial (0-5 cm) que propició una menor saturación por agua que el LC. Respecto a los parámetros relacionados con la agregación, el NL aumentó los macroagregados hasta los 10 cm de profundidad y favoreció la acumulación de CO y N en todas las fracciones de tamaño de agregados. Sin embargo, la recuperación del grado de macroagregación tras el cese del laboreo resulta lenta en comparación con otros suelos, posiblemente debido al bajo contenido en arcilla en el horizonte Ap. En comparación con el NL, la enmienda mostró también un efecto positivo, aunque muy ligero, en la agregación del suelo. En contradicción con otros estudios en suelos ácidos, nuestros resultados indican la existencia de una jerarquía de agregados, y destacan el papel importante de la MO en la mejora de la agregación. Tanto el NL como la enmienda favorecieron por separado varias propiedades químicas, físicas y biológicas del suelo, pero, en general, encontramos los mayores beneficios con su uso combinado. Además, a largo plazo el efecto positivo de NL en las propiedades del suelo fue en aumento, mientras que el efecto beneficioso de la enmienda se limitó básicamente a las propiedades químicas y se desvaneció en pocos años. Destacamos que las condiciones meteorológicas a lo largo del ensayo beneficiaron la producción de biomasa en NL, y en consecuencia las propiedades relacionadas con la materia orgánica, por lo que son un factor a tener en cuenta a la hora de evaluar los efectos de la enmienda y el laboreo sobre las propiedades del suelo, especialmente en zonas donde esas condiciones son muy variables entre una campaña y otra. Los resultados de este estudio han puesto de manifiesto que el NL no ha mermado la eficacia de la enmienda caliza, posiblemente gracias a la alta solubilidad de la enmienda aplicada, es más, el manejo con NL y enmienda es el que ha favorecido en mayor medida ciertos parámetros de calidad del suelo. Por el contrario el LC sí parece anular los beneficios de la enmienda en relación con las propiedades relacionadas con la MO. Por tanto, cabe concluir que la combinación de NL y la enmienda es una práctica adecuada para mejorar las propiedades químicas y físicas de suelos ácidos degradados por el laboreo. ABSTRACT Excessive acidity in soils is associated with deficiencies in certain nutrients and high concentrations of available aluminum, which is toxic for most Mediterranean crops. Tilling these soils results in the loss of soil organic matter (SOM), damages soil structure and reduces biological activity, ultimately degrading soil quality. It is expected, therefore, that when acid soils are tilled, their particular problems will tend to get worse. In our study area, the "Cañamero’s Raña” (Extremadura, Spain), acid soils degraded by an inappropriate tillage prevail. Rañas are large and flat platforms with very old soils (Palexerults), which are characterized by an exchange complex dominated by aluminum and an acid pH which decreases with depth. These soils have a strong Bt horizon rich in kaolinite clays, which encourages the formation of perched water-tables near the soil surface during periods of excessive rain. During the first third of the 20th century, these soils, that previously supported cork oak or its scrub replacement, were cultivated. Tillage accelerated the mineralization of the SOM, aggravating the problems of excessive acidity, which finally led to the abandonment of the land due to low productivity. To recover the quality of these degraded soils and to obtain consistent yields it is necessary, first, to apply amendments to raise the pH and reduce aluminum toxicity, and second to encourage the accumulation of SOM. In 2005 a field trial was established in the Raña to study the influence of no-tillage and the use of a Ca-amendment on soil quality related parameters in a forage crop agrosystem. The experimental design was a split-plot with four replicates where the main factor was tillage type, no-tillage (NT) versus traditional tillage (TT) and the secondary factor was the use or not of a Ca-amendment. The Ca-amendment was a mixture of sugar foam and red gypsum that was incorporated into the top 7 cm of the soil. Since the beginning of the experiment, NT had a positive influence on total and particulate organic carbon (TOC and POC, respectively), while the Ca-amendment had a small positive influence at the beginning of the study but its effect diminished with time. The highest TOC and POC contents were observed when NT and the Ca-amendment were combined. The Ca-amendment, even under NT, rapidly increased pH and Ca, and decreased the aluminum content to a depth of 50 cm, as well as improving soil aggregation slightly. NT, due to the increased POC, TOC and Glomalin-related soil proteins (GRSP), which can form stable non-toxic compounds with aluminum, also contributed to the reduction of aluminum toxicity in the upper layer. When perched water-tables near the soil surface were formed in campaigns with excessive rainfall, NT provided more favorable conditions for germination and crop development, resulting in higher yields compared with TT. This was directly related to the higher water storage capacity and the greater transmissivity of the water downwards from the upper layers, which led to lower water saturation under NT compared with TT. With regards to the aggregation-related parameters, NT increased macroaggregation to a depth of 10 cm and favored the accumulation of OC and N in all aggregate size fractions. However, the degree of recovery of macroaggregation after tillage ceased was slow compared with other soils, possibly due to the low clay content in the Ap horizon. Compared with NT, the Ca-amendment had a slight positive effect on soil aggregation. In contrast to other studies in acid soils, our results indicate the existence of an aggregate hierarchy, and highlight the important role of SOM in improving aggregation. Both NT and the Ca-amendment separately favored various chemical, physical and biological soil properties, but in general we found the greatest benefits when the two treatments were combined. In addition, the positive effect of NT on soil properties increased with time, while the beneficial effect of the Ca-amendment, which was limited to the chemical properties, vanished after a few years. It is important to note that the meteorological conditions throughout the experiment benefited biomass production under NT and, as a consequence, organic matter related properties. This suggests that meteorological conditions are a factor to consider when evaluating the effects of Ca-amendments and tillage on soil properties, especially in areas where such conditions vary significantly from one campaign to another. The results of this study show that NT did not diminish the effectiveness of the Ca-amendment, possibly due to the high solubility of the selected amendment. Moreover, the combination of NT and the Ca-amendment was actually the management that favored certain soil quality parameters the most. By contrast, TT seemed to nullify the benefits of the Ca-amendment with regards to the OM related properties. In conclusion, the combination of NT and the application of a Ca-amendment is an advisable practice for improving the chemical and physical properties of acid soils degraded by tillage.

Comportamiento térmico y mecánico del yeso con adiciones de aerogel de sílice granulado

La presente tesis doctoral aborda el estudio de un nuevo material mineral, compuesto principalmente por una matriz de yeso (proveniente de un conglomerante industrial basado en sulfato de calcio multifase) y partículas de aerogel de sílice hidrófugo mesoporoso, compatibilizadas mediante un surfactante polimérico, debido a su alto carácter hidrófugo. La investigación se centra en conocer los factores que influyen en las propiedades mecánicas y conductividad térmica del material compuesto generado. Este estudio pretende contribuir al conocimiento sobre el desarrollo de nuevos morteros de elevado aislamiento térmico que puedan ser utilizados en la rehabilitación energética de edificios de viviendas existentes, debido a que estos representan gran parte del consumo energético del parque de viviendas de España, aunque también a nivel internacional. De los materiales utilizados para desarrollar los morteros estudiados, el yeso, además de ser un material muy abundante, especialmente en España, requiere una menor cantidad de energía para la fabricación de un conglomerante (debido a una menor temperatura de fabricación), en comparación con el cemento o la cal, por lo que presenta una menor huella de carbono que estos últimos. Por otro lado, el aerogel de sílice hidrófugo mesoporoso es, de acuerdo con la documentación disponible, el material que posee actualmente la mayor capacidad de aislamiento térmico en el mercado. El desarrollo de nuevos morteros minerales con una capacidad de aislamiento térmico mayor que los materiales aislantes utilizados tradicionalmente, tiene una aplicación relevante en los casos de rehabilitación energética de edificios históricos y patrimoniales, en los que se requiere la aplicación del aislamiento por el interior de la fachada, ya que este tipo de soluciones tienen el inconveniente de reducir el espacio habitable de las áreas involucradas, especialmente en zonas climáticas en las que el aislamiento térmico puede suponer un espesor considerable, por lo que es ideal utilizar materiales de altas prestaciones de aislamiento térmico capaces de aportar el mismo nivel de aislamiento (o incluso mayor), pero en un espesor considerablemente menor. La investigación se desarrolla en tres etapas: bibliográfica, experimental y de simulación. La primera etapa, parte del estudio de la bibliografía existente, relacionada con materiales aislantes, incluyendo soluciones basadas, tanto en morteros aislantes, como en paneles de aislamiento térmico. La segunda, de carácter experimental, se centra en estudiar la influencia de la microestrucrura y macroestructura, del nuevo material mineral, en las propiedades físicas elementales, mecánicas y conductividad térmica del compuesto. La tercera etapa, mediante una simulación del consumo energético, consiste en cuantificar teóricamente el potencial ahorro energético que puede aportar este material en un caso de rehabilitación energética en particular. La investigación experimental se centró principalmente en conocer los factores principales que influyen en las propiedades mecánicas y conductividad térmica de los materiales compuestos minerales desarrollados en esta tesis. Para ello, se llevó a cabo una caracterización de los materiales de estudio, así como el desarrollo de distintas muestras de ensayo, de tal forma que se pudo estudiar, tanto la hidratación del yeso en los compuestos, como su posterior microestructura y macroestructura, aspectos fundamentales para el entendimiento de las propiedades mecánicas y conductividad térmica del compuesto aislante. De este modo, se pudieron conocer y cuantificar, los factores que influyen en las propiedades estudiadas, aportando una base de conocimiento y entendimiento de este tipo de compuestos minerales con aerogel de sílice hidrófugo, no existiendo estudios publicados hasta el momento de finalización de esta tesis, con la aproximación al material propuesta en este estudio, ni con yeso (basado en sulfato de calcio multifase), ni con otro tipo de conglomerantes. Particularmente, se determinó la influencia que tiene la incorporación de partículas de aerogel de sílice hidrófugo, en grandes proporciones en volumen, en un compuesto mineral basado en distintas fases de sulfato de calcio. No obstante, para llevar a cabo las mezclas, fue necesario utilizar un surfactante para compatibilizar este tipo de partículas, con el conglomerante basado en agua. El uso de este tipo de aditivos tiene una influencia, no solo en el aerogel, sino en las propiedades del compuesto en general, dependiendo de su concentración, por lo que se establecieron dos porcentajes de adición: la primera, determinada a partir de la cantidad mínima necesaria para compatibilizar las mezclas (0,1% del agua de amasado), y la segunda, como límite superior, la concentración utilizada habitualmente a nivel industrial para estabilizar burbujas de aire en hormigones espumados (5%). El surfactante utilizado mostró la capacidad de modificar la superficie del aerogel, cambiando el comportamiento de las partículas frente al agua, permitiendo una invasión parcial de su estructura porosa, por parte del agua de amasado. Este comportamiento supone un aumento muy importante en la relación agua/yeso, afectando el hábito cristalino e influenciando negativamente las propiedades mecánicas de la matriz de yeso, presentando un efecto aún notable a mayor concentración de surfactante (5%). En cuanto a las propiedades finales alcanzadas, fue posible lograr un compuesto mineral ultraligero (200 kg/m3), con alrededor de un 60% de aerogel en volumen y de alta capacidad aislante (0,028 W/m•K), presentando una conductividad térmica notablemente menor que los morteros aislantes del mercado, e incluso también menor que la de los aislantes tradicionales basado en las lanas minerales o EPS; no obstante, con la limitante de presentar bajas propiedades mecánicas, condicionando su posible aplicación futura. Entre los factores principales relacionados con las propiedades mecánicas, se encontró que estas dependen exponencialmente del volumen de yeso en el compuesto; no obstante, factores de segundo orden, como el grado de hidratación, o una mejor distribución del conglomerante entre las partículas de aerogel, debido al aumento de la superficie específica del polvo mineral, pueden aumentar las propiedades mecánicas entre el doble y el triple, dependiendo del volumen de aerogel en cuestión. Además, se encontró que el aerogel, en conjunto con el surfactante, es capaz de introducir una gran cantidad de aire (0,70 m3 por cada m3 de aerogel), que unido al agua evaporada (no consumida por el conglomerante durante la hidratación), el volumen de aire total alcanza, generalmente, un 40%, independientemente de la cantidad de aerogel en la mezcla. De este modo, el aire introducido en la matriz desplaza las proporciones en volumen del aerogel y del yeso, disminuyendo, tanto las propiedades mecánicas, como la capacidad aislante de compuesto mineral. Por otro lado, la conductividad térmica mostró tener una dependencia directa de la contribución de las tres fases principales en el compuesto: yeso, aerogel y aire ocluido. De este modo, se pudo desarrollar un modelo matemático, adaptado de uno existente, capaz de calcular, con bastante precisión, la relación de los tres componentes mencionados, en la conductividad térmica de los compuestos, para el rango de volúmenes y materiales utilizados en esta tesis. Finalmente, la simulación del consumo energético realizada a una vivienda típica de España, de los años 1900 a 1959 (basada en muros de ladrillo macizo), para las zonas climáticas estudiadas (A, D y E), permitió observar el potencial ahorro energético que puede aportar este material, dependiendo de su espesor, como aislamiento interior de los muros de fachada. Particularmente, para la zona A, se determinó un espesor óptimo de 1 cm, mientras que para la zona D y E, 3,5 y 3,9 cm respectivamente. En este sentido, el nuevo material estudiado es capaz de disminuir, entre un 35% y un 80%, el espesor de la capa aislante, en comparación con paneles de lana de roca o los morteros minerales de mayor capacidad aislante del mercado español respectivamente. ABSTRACT The present doctoral thesis studies a new mineral-based composite material, composed by a gypsum matrix (based on an industrial multiphase gypsum binder) and mesoporous hydrophobic silica aerogel particles, compatibilized with a polymeric surfactant due to the high hydrophobic character of the insulating particles. This study pretends to contribute to the development of new composite insulating materials that could be used in energy renovation of existing dwellings, in order to reduce their high energy consumption, as they represent a great part of the total energy consumed in Spain, but also internationally. Between the materials used to develop de studied insulating mortars, gypsum, besides being an abundant material, especially in Spain, requires less energy for the manufacture of a mineral binder (due to lower manufacturing temperatures), compared to lime or cement, thus presenting lower carbon footprint. In other hand, the hydrophobic mesoporous silica aerogel, is, according to the existing references, the material with the highest know insulating capacity in the market. The development of new mineral mortars with higher thermal insulation capacity than traditional insulating materials, presents a relevant application in energy retrofitting of historic and cultural heritage buildings, in which implies that the insulating material should be installed as an internal layer, rather than as an external insulating system. This type of solution involves a reduced internal useful area, especially in climatic zones where the demand for thermal insulation is higher, and so the insulating layer thickness, being idealistic to use materials with very high insulating properties, in order to reach same insulating level (or higher), but in lower thickness than the provided by traditional insulating materials. This research is developed in three main stages: bibliographic, experimental and simulation. The first stage starts by studying the existing references regarding thermally insulating materials, including existing insulating mortars and insulating panels. The second stage, mainly experimental, is centered in the study of the the influence of the microstructure and macrostructure in the physical and mechanical properties, and also in the thermal conductivity of the new mineral-based material. The thirds stage, through energy simulation, consists in theoretically quantifying the energy savings potential that can provide this type of insulating material, in a particular energy retrofitting case study. The experimental research is mainly focused in the study of the factors that influence the mechanical properties and the thermal conductivity of the thermal insulating mineral composites developed in this thesis. For this, the characterization of the studied materials has been performed, as well as the development of several experimental samples, in order to study the hydration of the mineral binder within the composites, but also the final microstructure and macrostructure, fundamental aspects for the understanding of the composite’s mechanical and insulating properties. Thus, is was possible to determine and quantify the factors that influence the studied material properties, providing a knowledge base and understanding of mineral composites that comprises mesoporous hydrophobic silica aerogel particles, being the first study up to date regarding the specific approach of the present study, regarding not just multiphase calcium sulfate plaster, but also other mineral binders. Particularly, the influence of the incorporation of hydrophobic silica aerogel particles, in high volume ratios into a mineral compound, based on different phases of calcium sulfate has been determined. However, to perform mixing, it is necessary to use a surfactant in order to compatibilize these particles with the water-based mineral binder. The use of such additives has an influence, not only in the aerogel, but the overall properties of the compound, so two different surfactant concentration has been studied: the first, the minimum amount of surfactant (used in this thesis) in order to develop the slurries (0.1% concentration of the mixing water), and the second, as the upper limit, the concentration usually used industrially to stabilize air bubbles in foamed concrete (5%). One of the side effects of using such additive, was the modification of the aerogel particles, by changing their behavior in respect to water, generating a partial invasion of the aerogel’s porous structure, by the mixing water. This behavior produces a very important increase in water/binder ratios, affecting the crystal habit and negatively influencing the mechanical properties of the gypsum matrix. This effect further increased when a higher concentration of surfactant (5%) is used. Regarding final materials properties, it was possible to achieve an ultra-lightweight mineral composite (200 kg/m3), with around 60% by volume of aerogel, presenting a very high insulating capacity (0.028 W/m•K), a noticeable lower thermal conductivity compared to the insulating mortars and traditional thermal insulating panels on the market, such as mineral wool or EPS; however, the limiting factor for future’s material application in buildings, is related to the very low mechanical properties achieved. Among the main factors related to the mechanical properties, it has been found an exponential correlation to the volume of gypsum in the composite. However, second-order factors such as the degree of hydration, or a better distribution of the binder between the aerogel particles, due to the increased surface area of the mineral powder, can increase the mechanical properties between two to three times, depending aerogel volume involved. In addition, it was found that the aerogel, together with the surfactant, is able to entrain a large amount of air volume (around 0.70 m3 per m3 of aerogel), which together with the evaporated water (not consumed by the binder during hydration), can reach generally around 40% of entrained air within the gypsum matrix, regardless of the amount of aerogel in the mixture. Thus, the entrained air into the matrix displaces the volume proportions of the aerogel and gypsum, reducing both mechanical and insulating properties of the mineral composite. On the other hand, it has been observed a direct contribution of three main phases into the thermal conductivity of the composite: gypsum, aerogel and entrained air. Thus, it was possible to develop a mathematical model (adapted from an existing one), capable of calculating quite accurate the thermal conductivity of such mineral composites, from the ratio these three components and for the range of volumes and materials used in this thesis. Finally, the energy simulation performed to a typical Spanish dwelling, from the years 1900 to 1959 (mainly constructed with massive clay bricks), within three climatic zones of Spain (A, D and E), showed the energy savings potential that can provide this type of insulating material, depending on the thickness of the applied layer. Particularly, for the climatic A zone, it has been found an optimal layer thickness of 1 cm, while for zone D and E, 3.5 and 3.9 cm respectively. In this manner, the new studied materials is capable of decreasing the thickness of the insulating layer by 35% and 80%, compared with rock wool panels or mineral mortars with the highest insulating performance of the Spanish market respectively.

Anhydrite/aerogel composites for thermal insulation

High performance thermal insulating composite materials can be produced with mineral binders and hydrophobic aerogel particles through a hydrophilization process for the latter with surfactants. The present study is focused on the development of aerogel/calcium sulfate composites by the hydrophilization of hydrophobic silica aerogel particles through a polymer-based surfactant. Its effects on the microstructure and hydration degree are examined as well as their relation to the resulting mechanical and physical properties. Results show that composites with an around 60 % of aerogel by volume can achieve a thermal conductivity <30 mW/m × K. Interestingly, a surfactant addition of 0.1 % by wt% of the water in the mixtures provides better material properties compared to a surfactant wt% addition of 5 %. However, it has been found around 40 % entrained air, affecting the material properties by reducing the binder and aerogel volume fractions within the composites. Moreover, gypsum crystallization starts to be inhibited at aerogel volume fractions >35 %. Towards material optimization, a model for the calculation of thermal conductivity of composites and an equation for the compressive strength are proposed.

Low-temperature concentration of tellurium and gold in continental red bed successions

Acknowledgements This research was supported by NERC grants (NE/L001764/1, NE/M010953/1). We are grateful to J. Still and A. Sandison for technical support and to the gypsum mines and C. Brolley for access and sampling. Critical comments from Cristiana Ciobanu, Eric Gloaguen and Georges Calas are gratefully acknowledged. The authors have no conflicts of interest to declare

Estado nutricional de cultivares de cana-de-açúcar em função da aplicação de calcário e gesso no solo

As áreas destinadas à cultura de cana-de-açúcar estão concentradas em áreas de Cerrado, que são solos ácidos, com elevada saturação por alumínio e baixa saturação por bases. Para correção destas características, faz-se o uso de corretivos e fertilizantes no momento da implantação da cultura. Embora a toxidez por alumínio seja uma das mais sérias limitações ao crescimento de plantas em solos ácidos, há uma carência de estudos relacionando-a com a cultura de cana-de-açúcar. Com base nisto, o objeto deste trabalho foi avaliar o efeito da aplicação de calcário e gesso sobre o estado nutricional de quatro cultivares de cana-de-açúcar, distintas quanto à exigência nutricional, na fase de perfilhamento da cultura. Para tanto, desenvolveu-se experimento em casa de vegetação com vasos contendo 4 kg de amostra de solo, com saturação por alumínio de 29%, como substrato, com os seguintes tratamentos: 1) aplicação de calcário, 2) aplicação de gesso, e 3) controle, sem adição de calcário e gesso. Os cultivares utilizados foram: IACSP95-5000, IACSP94-2094, SP80-3280 e IAC95-3028. Após adição dos tratamentos, as amostras de solo foram incubadas por 45 dias. Para os materiais vegetais, mini-toletes de gema única das cultivares foram pré-brotados, crescidos por 90 dias e transplantados para os vasos, para os respectivos tratamentos. As plantas foram adubadas com macro e micronutrientes e cultivadas por 60 dias. Os tratamentos foram caracterizados quanto aos atributos químicos para avaliação da fertilidade após a incubação e após a coleta das plantas. Nas plantas, foram feitas avaliações de: clorofila, flavonoides, índice de balanço do nitrogênio (NBI), concentração de alumínio e dos nutrientes e produção de matéria seca de folha, colmo e raiz. Enquanto o tratamento gesso não diferiu do controle, o tratamento calcário foi efetivo para correção da reação da amostra de solo, com elevação dos valores de pH e saturação por bases, e redução da saturação por alumínio e acidez total, além do aumento nos teores de Ca e Mg. A adubação NPK+micro foi efetiva para aumentar os teores de P e K dos substratos de todos os tratamentos. Nas plantas, para todos os cultivares, os índices de clorofila, flavonoides e NBI foram mais adequados no tratamento calcário, em relação ao controle e ao gesso. A produção de matéria seca total e das partes das plantas, de modo geral, foi maior para a IACSP95-5000, intermediaria para a IACSP35-3028 e menor para a IACSP94-2094 e SP80-3280. Quanto aos tratamentos, não houve efeito do calcário e gesso sobre a produção de matéria seca de folha, contudo, houve aumento de produção de matéria seca de colmo e raiz pelo calcário, na cultivar IACSP95-5000. Independente do tratamento, as cultivares apresentaram concentração de alumínio superior a 5000 mg kg-1 nas raízes e inferiores a 360 e 160 mg kg-1 nas folhas e colmos, respectivamente, evidenciando que o Al foi acúmulo nas raízes das plantas. De modo geral, as concentrações de macro e micronutrientes variaram com os tratamentos e cultivares, porém sem valores altos e baixos extremos. Concluiu-se que a cultivar IACSP95-5000 tem maior potencial de produção em resposta à aplicação de calcário e que a saturação de alumínio de 29% não apresenta efeito negativo sobre a produção de matéria seca, exceto da cultivar IACSP95-5000, e estado nutricional das cultivares de cana-de-açúcar

Applying reactive models to column experiments to assess the hydrogeochemistry of seawater intrusion: optimising ACUAINTRUSION and selecting cation exchange coefficients with PHREEQC

Three sets of laboratory column experimental results concerning the hydrogeochemistry of seawater intrusion have been modelled using two codes: ACUAINTRUSION (Chemical Engineering Department, University of Alicante) and PHREEQC (U.S.G.S.). These reactive models utilise the hydrodynamic parameters determined using the ACUAINTRUSION TRANSPORT software and fit the chloride breakthrough curves perfectly. The ACUAINTRUSION code was improved, and the instabilities were studied relative to the discretisation. The relative square errors were obtained using different combinations of the spatial and temporal steps: the global error for the total experimental data and the partial error for each element. Good simulations for the three experiments were obtained using the ACUAINTRUSION software with slight variations in the selectivity coefficients for both sediments determined in batch experiments with fresh water. The cation exchange parameters included in ACUAINTRUSION are those reported by the Gapon convention with modified exponents for the Ca/Mg exchange. PHREEQC simulations performed using the Gains-Thomas convention were unsatisfactory, with the exchange coefficients from the database of PHREEQC (or range), but those determined with fresh water – natural sediment allowed only an approximation to be obtained. For the treated sediment, the adjusted exchange coefficients were determined to improve the simulation and are vastly different from those from the database of PHREEQC or batch experiment values; however, these values fall in an order similar to the others determined under dynamic conditions. Different cation concentrations were simulated using two different software packages; this disparity could be attributed to the defined selectivity coefficients that affect the gypsum equilibrium. Consequently, different calculated sulphate concentrations are obtained using each type of software; a smaller mismatch was predicted using ACUAINTRUSION. In general, the presented simulations by ACUAINTRUSION and PHREEQC produced similar results, making predictions consistent with the experimental data. However, the simulated results are not identical to the experimental data; sulphate (total S) is overpredicted by both models, most likely due to such factors as the kinetics of gypsum, the possible variations in the exchange coefficients due to salinity and the neglect of other processes.

Mineralogical analysis of ceramic tiles by FTIR: A quantitative attempt

A method for quantitative mineralogical analysis by ATR-FTIR has been developed. The method relies on the use of the main band of calcite as a reference for the normalization of the IR spectrum of a mineral sample. In this way, the molar absorptivity coefficient in the Lambert–Beer law and the components of a mixture in mole percentage can be calculated. The GAMS equation modeling environment and the NLP solver CONOPT (©ARKI Consulting and Development) were used to correlate the experimental data in the samples considered. Mixtures of different minerals and gypsum were used in order to measure the minimum band intensity that must be considered for calculations and the detection limit. Accordingly, bands of intensity lower than 0.01 were discarded. The detection limit for gypsum was about 7% (mol/total mole). Good agreement was obtained when this FTIR method was applied to ceramic tiles previously analyzed by X-ray diffraction (XRD) or mineral mixtures prepared in the lab.

Clay mineralogy of carbonate-rich sediments of ODP Leg 101 sites

The insoluble residues of samples from ODP Sites 626 and 627 can be subdivided into four groups: (1) illite, 7 A minerals, quartz and feldspar; (2) smectite and zeolite (clinoptilolite); (3) palygorskite and in places sepiolite; and (4) glauconite and pyrite. Whereas group 1 is clearly terrigenous and group 4 authigenic, group 2 is most probably authigenic, as indicated by its abundance in samples with small insoluble residues and its appearance in SEM photographs. Group 3 is authigenic in Albian peritidal dolomite and possibly terrigenous in middle Miocene slumps and debris flows. Smectite crystallinity increases with age. This increase, however, is less pronounced in the Bahamian carbonate-rich samples than in the carbonate-poor silts south of Guatemala (DSDP Leg 84, Sites 569 and 570, the only comparable investigation) as far as can be judged from such a small number of samples.

Sulfur-isotope analyses of gypsium samples from the Southeast Greenland margin, southern Alaska and Gulf of Alaska (Table 1)

Gypsum grains were identified in Miocene-Pleistocene sediment cores from two deep-water ODP sites, Site 918 off the SE Greenland margin and Site 887 in the Gulf of Alaska, and in Holocene sediment cores from shallow-water localities in Disenchantment Bay and Muir Inlet in southern Alaska. Although initial morphologic and textural observations suggested a complex system in which the gypsum may have had more than one origin, quantitative sulfur isotope analyses of the gypsum provide evidence of its detrital nature. d34S values in gypsum from southern Alaska range between +0.0 and +7.1 per mil. Gypsum has d34S values between -27.1 and -27.5 per mil in the Gulf of Alaska and values between -28.5 and +0.2 per mil off the SE Greenland margin. All of these isotopic signatures are too highly depleted in d34S to have precipitated from seawater, present or past. In addition there is no significant change in d34S values for gypsum crystals with differing physical characteristics (abraded vs. unabraded) from the same stratigraphic horizon, suggesting all the gypsum is detrital regardless of the degree of abrasion. The isotopic and physical evidence, in combination with the onshore geology the environmental setting, and site characteristics of the gypsum-bearing marine localities, lead us to propose that the ultimate source of the gypsum is precipitation from freeze-induced terrestrial sediment or soil brines. Furthermore the combined evidence suggests that the subsequent occurrence of gypsum in glacimarine sediments results from ice-rafting (by icebergs or sea ice) of the frozen regolith and/or, in the proximal glacimarine setting of southern Alaska, very rapid burial via turbidity currents.