Effect of commercial mouthwashes on the corrosion resistance of Ti-10Mo experimental alloy

The purpose of this work was to evaluate the effect of three commercial mouthwashes on the corrosion resistance of Ti-10Mo experimental alloy. Experiments were made at 37.0 +/- 0.5 degrees C in a conventional three-compartment double wall glass cell containing commercial mouthwashes. Three mouthwashes with different active ingredients were tested: ( I) 0.05% sodium fluoride + 0.03% triclosan; (II) 0.5 g/l cetylpyridinium chloride + 0.05% sodium fluoride; (III) 0.12% chlorohexidine digluconate. The assessment of the individual effect of active ingredients was studied by using 0.05% sodium fluoride. Commercially pure titanium (CP Ti) was used as control. Microstructures from Ti-10Mo experimental alloy and CP Ti were also evaluated using optical microscopy. Ti-10Mo as-cast alloy shows the typical rapidly cooled dendrites microstructure (beta phase) while CP Ti has exhibited a metastable martensitic microstructure. Electrochemical behavior of dental materials here studied was more affected by mouthwash type than by Ti alloy composition or microstructure. In both alloys passivation phenomenon was observed. This process may be mainly related to Ti oxides or other Ti species present in spontaneously formed film. Small differences in passive current densities values may be connected with changes in film porosity and thickness. Protective characteristics of this passive film are lower in 0.05% sodium fluoride + 0.03% triclosan mouthwash than in the other two mouthwashes tested.

Structural characteristics of silica sonogels prepared with additions of isopropyl alcohol

Wet silica gels with similar to 1.4 x 10(-3) mol SiO2/cm(3) and similar to 92 vol% liquid phase were obtained from sonohydrolysis of tetraethoxysilane (TEOS) with different additions of isopropyl alcohol ( IPA). The IPA/TEOS molar ratio R was changed from 0 to 4. Aerogels were obtained by supercritical CO2 extraction. The samples were analyzed by small-angle X-ray scattering (SAXS) and nitrogen adsorption. The wet gels exhibit mass fractal structure with fractal dimension increasing from D similar to 2.10 to D similar to 2.22, characteristic length xi decreasing from similar to 9.5 to similar to 6.9 nm, as R increases from 0 to 4, and an estimated characteristic length for the primary silica particles lower than similar to 0.3 nm. The supercritical process apparently eliminates a fraction of the porosity, increasing the mass fractal dimension and shortening the fractality domain in the mesopore region. The fundamental role of isopropyl alcohol on the structure of the resulting aerogels is to decrease the porosity and the pore mean size as R changes from pure TEOS to R = 4. A secondary structure appearing in the micropore region of the aerogels can be described as a mass/surface fractal structure, with correlated mass fractal dimension D-m similar to 2.7 and surface fractal dimension D-s similar to 2.3, as inferred from SAXS and nitrogen adsorption data.

A Semi-Continuous Analyzer for the Fluorimetric Determination of Atmospheric Formaldehyde

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effects of thermal annealing on the semi-insulating properties of radio frequency magnetron sputtering-produced germanate thin films

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Atributos físicos de latossolo vermelho sob pousio ou cultivado com forrageiras tropicais sob pastejo

The objective was to study the physical attributes of an Oxisol under fallow or planted with tropical grasses under grazing. The experiment was conducted under the experimental design of randomized blocks in split-plot 2 x 5, being five types of use of soil (Brachiaria ruziziensis, Panicum maximum cv. Aries, Brachiaria brizantha cv. MG5, Panicum maximum cv. Mombaca and fallow) and two evaluation periods (after the first and after the second grazing), with four replications. We evaluated the characteristics of soil bulk density, total porosity, microporosity and macroporosity, after the first and second grazing, and soil resistance to penetration after the second grazing. In layer of 0.00 to 0.10 m, the macroporosity was affected by the interaction between types of use and evaluation periods, while the microporosity and total porosity were reduced and the density was increased from first to second evaluation time. In the subsurface layer (0.10-0.20 m), there were significant effect only of evaluation time, on the macroporosity, total porosity and density. The porosity were reduced, while the density increased from first to second evaluation time. No significant effects of types of use of soil on penetration resistance in all layers studied. The maintenance of an Oxisol under fallow or cultivation with tropical grasses subjected to grazing cattle causes a reduction in total porosity and increased density of surface soil layers (0 to 0.10 m) and subsurface (0.10 - 0.20 m), without promoting changes on resistance to penetration mechanics.

Efeito de Diferentes Níveis de Manganês e Fósforo Sobre o Desempenho e a Qualidade da Casca dos Ovos de Poedeiras Comerciais

The objective of this experiment was to evaluate the different levels of manganese and phosphorus (P) on the performance and eggshell quality and on determined blood constituents of 96 laying hens Hy-Line W36, with 60 weeks of age, distributed in 24 lots with four hens each. A completely randomized experimental design was used in a factorial arrangement (3x2), manganese levels (70, 140 and 210 ppm) and total phosphorus levels (.35 and .55%), totalizing six treatments with four replicates each. The experimental diets were isoproteic (16.0% CP), isocaloric (2800 kcal ME/kg), isocalcium (4.0% Ca) and isosodium (.16% Na). The manganese levels did not alter the production and eggshell quality. However, when hens were fed diets containing .35% of total P, there were observed decreases in the egg production, egg weight and egg mass, without alterations in eggshell quality characteristics. The supplemental manganese levels were not effective to improve eggshell quality at the final phase of production. The total phosphorus level of .35% was inadequate for the laying hens to express the normal production characteristics.

Adubação verde em Citrus: Influência na porosidade e retenção de água de um latossolo vermelho-escuro do noroeste do estado de São Paulo

The objective of this research was to study the porosity, bulk density and retention of water of an Oxisol, located in the Northwestern region of Sn̄o Paulo state, Brazil. The soil was cultivated with Citrus sp., to which green manure was applied between rows for three years. Each of six species of green manure crops (Crotalaria juncea L., Mucuna deeringiana Steph. & Bart., Canavalia ensiformis L. DC., Cajanus cajan L., Lablab purpureum L. and Ricinus communis L.) were seeded for three years (1995, 1996 and 1997) between Citrus rows, plus a treatment with a mix of all six species and a control (natural regrowth af vegetation). The experimental design was a randomized complete block design, with four replications for each of the eight treatments. Water retention, microporosity, macroporosity, total porosity and bulk density were analyzed in the beginning (1995) and end (1997) of the experiment, at three depth ranges (0-0.10; 0.10-0.20 and 0.20-0.40m). We concluded that there were statistically significant differences for bulk density, macroporosity, total porosity and retention of water among the different soil depth ranges; there were no significant differences among treatments though.

Specific depth cone resistivity measurements to determine soil engineering properties

The University of British Columbia (UBC) began performing piezocone penetration tests (CPTU) with electrical resistivity measurements (RCPTU) in 1989. Since then, RCPTU research at UBC has focused on obtaining geo-environmental parameters such as fluid resistivity and soil engineering properties such as porosity and degree of saturation from measurements of bulk soil electrical resistivity using the empirical relationship proposed by Archie (1942). Within this framework, the paper illustrates and discusses important design and calibration issues for resistivity modules such as the use of isolated circuitry to achieve linear calibrations over large ranges of resistivity. The suitability of RCPTU measurements for determination of geo-environmental and geotechnical parameters are assessed using typical ranges of soil and groundwater properties and methods of isolating individual factors for study are discussed. Illustrative examples of RCPTU research efforts including the environmental characterization of mine tailings, delineation of saline water intrusions in fresh water aquifers and the quality control of geotechnical ground densification are presented throughout the text. It is shown that groundwater temperature and hence ion mobility is not significantly altered by frictional heat generated during piezocone penetration and that ratio-based approaches to monitoring soil porosity can be used to eliminate the requirement for extensive groundwater sampling programs. Lastly, it is shown that RCPTU measurements above the water table can only be made using resistivity modules that are stable over a large range of resistivities and that such measurements are the most difficult to interpret because of grain surface conduction effects and generally unknown fluid resistivities.

Efeito de resíduos vegetais de milheto (Pennisetum americanum) e da calagem em algumas propriedades físicas e químicas de um nitossolo vermelho em sistema de semeadura direta

This work studied alterations of physical properties of a distroferric red nitosol due to millet (Pennisetum americanum) covering, with or without liming, in a no-tillage system during the agricultural years of 1999/2000 and 2000/2001, using soybean and corn as culture succession. 6m×10m plots, with and without millet as vegetal covering, received only one initial superficial application of limestone, 3.1 t ha-1 in the first half of each plot in order to obtain 70% base saturation (V), after the desiccation of the millet. Some physical properties as soil density, aggregate stability, > 2 mm aggregate proportion, macro and micro porosity were analyzed whereas the chemical analysis determined Ca and Mg macro nutrients, organic matter, soil pH and H+Al. Millet vegetal residues and surface liming did not alter soil density nor the average weight diameter (AWD), > 2 mm aggregate, soil macro porosity and organic matter content, twenty-four months after the no-tillage system implantation for studied experimental conditions. Soil micro porosity was significantly affected in layers deeper than 0.20 m, in treatment with millet and limestone. Calcium, magnesium and H + Al contents and the soil pH values suffered significant alterations in superficial layer, between 0-0.05 m.

Atributos químicos e físicos de um solo tratado com biossólido industrial e cultivado com milho

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Porous titanium scaffolds produced by powder metallurgy for biomedical applications

Porous titanium scaffolds are promising materials for biomedical applications such as prosthetic anchors, fillers and bone reconstruction. This study evaluated the bone/titanium interface of scaffolds with interconnected pores prepared by powder metallurgy, using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Porous scaffolds and dense samples were implanted in the tibia of rabbits, which were subsequently killed 1, 4, and 8 weeks after surgery. Initial bone neoformation was observed one week after implantation. Bone ingrowth in pores and the Ca/P ratio at the interface were remarkably enhanced at 4 and 8 weeks. The results showed that the interconnected pores of the titanium scaffolds promoted bone ingrowth, which increased over time. The powder metallurgy technique thus proved effective in producing porous scaffolds and dense titanium for biomedical applications, allowing for adequate control of pore size and porosity and promoting bone ingrowth.

Influência do sistema de preparo e manejo de um latossolo vermelho nas suas propriedades físico-hídricas

The intensive use of the land for agricultural propose causes a series of modifications in attributes, which can take to soil degradation. In this context, the main goal of this research was to evaluate the influence of the soil tillage systems and management on its physical and hydric characteristics. The evaluations were carried out in July of 1999, at experimental plots of a Latossolo vermelho, a clay oxisoil, in the Faculdade de Engenharia Agrícola of the UNICAMP, at the county of Campinas, state of São Paulo. These plots were managed with the following treatments, along a period of eight years: no-tillage, chisel ploughing, conventional system with disk ploughing and revolving hoe. The evaluated physical and hydric parameters of the soil were: soil bulk density, particle density, total porosity, macro-porosity, micro-porosity, soil-water retention curve, hydraulic conductivity and basic infiltration. Significant differences were observed between the treatments on soil bulk density, infiltration, total porosity, macro-porosity and the micro-porosity. The chisel ploughing and no-tillage systems presented the higher values of soil bulk density; nevertheless in these conservationist systems were observed the higher values of basic infiltration.

Alternative to peat for Agaricus brasiliensis yield

Casing layer is one of the most important components of Agaricus spp. production and it directly affects mushroom productivity, size and mass. The aim of this study was to evaluate potential raw materials as a casing layer and their effect on Agaricus brasiliensis productivity. Raw materials from Brazil with potential use were selected and characterized, and the most promising ones were tested as casing layers for mushroom yield. Evaluated raw materials included lime schist, vermiculite, eucalyptus sawdust, sand, São Paulo peat, Santa Catarina peat, subsoil and charcoal. Particle size, porosity and water absorption in relation to mushroom yield for casing layers were determined. Lime schist, an alternate casing layer to peat, is presented and the effects of the casing layer on the mushroom yield are discussed. © 2009 Elsevier Ltd. All rights reserved.

Evaluation of bone ingrowth into porous titanium implant: Histomorphometric analysis in rabbits

A porous material for bone ingrowth with adequate pore structure and appropriate mechanical properties has long been sought as the ideal bone-implant interface. This study aimed to assess in vivo the influence of three types of porous titanium implant on the new bone ingrowth. The implants were produced by means of a powder metallurgy technique with different porosities and pore sizes: Group 1 = 30% and 180 μm; Group 2 = 30% and 300 μm; and Group 3 = 40% and 180 μm. Six rabbits received one implant of each type in the right and left tibiae and were sacrificed 8 weeks after surgery for histological and histomor-phometric analyses. Histological analysis confirmed new bone in contact with the implant, formed in direction of pores. Histomorphometric evaluation demonstrated that the new bone formation was statistically significantly lower in the group G1 than in group G3, (P = 0.023). Based on these results, increased porosity and pore size were concluded to have a positive effect on the amount of bone ingrowth.

Porosidade e infiltração de água do solo sob diferentes sistemas de manejo

Management systems affect soil structure, causing changes in porosity that can influence water infiltration into the soil. This study aimed to evaluate the effect of different management systems on the porosity and water infiltration in Distroferric Red Nitosol with clay texture. The management systems were: conventional with disc plow + two soft harrowing, conventional with heavy disc harrow + two soft harrowing, no tillage and fallow. The following attributes: porosity, pore shape and water infiltration velocity into the soil were determined. Management systems such as no-tillage, conventional with disc plow and heavy disc harrow, and fallow modify the porosity and the shape of pores of a Distroferric Red Nitosol, influencing water infiltration, which was favored in no-tillage for the greater presence of elongated pores.