Produção de enzimas quitosanolíticas utilizando Paenibacillus ehimensis e Paenibacillus chitinolyticus para obtenção de quitoologossacarídeos

The acquisition of oligosaccharides from chitosan has been the subject of several studies in the pharmaceutical, biochemical, food and medical due to functional properties of these compounds. This study aimed to boost its production of chitooligosaccharides (COS) through the optimization of production and characterization of chitosanolytic enzymes secreted by microorganisms Paenibacillus chitinolyticus and Paenibacillus ehimensis, and evaluating the antioxidant potential of the products obtained. In the process of optimizing the production of chitosanase were employed strategies Fractional Factorial Experimental Design and Central Composite Rotatable Design. The results identified the chitosan, peptone and yeast extract as the components that influenced the production of chitosanase by these microorganisms. With the optimization of the culture media was possible to obtain an increase of approximately 8.1 times (from 0.043 to 0.35 U.mL U.mL-1) and 7.6 times (from 0.08 U.mL-1 to 0.61 U.mL-1) in the enzymatic activity of chitosanase produced by P. chitinolyticus and P. ehimensis respectively. Enzyme complexes showed high stability in temperature ranges between 30º and 55º C and pH between 5.0 and 9.0. Has seen the share of organic solvents, divalent ions and other chemical agents on the activity of these enzymes, demonstrating high stability of these crude complexes and dependence of Mn2+. The COS generated showed the ability of DPPH radical scavenging activity, reaching a maximum rate of scavenging of 61% and 39% when they were produced with enzymes of P. ehimensis and P. chitinolyticus respectively. The use of these enzymes in raw form might facilitate its use for industrial applications

Análise de falhas em martelos oscilantes dos desfibradores da indústria sucroalcooleira da Região Norte-Nordeste

The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results

Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Reconfiguração dinâmica de estratégias distribuídas em dispositivos foundation fieldbus para a otimização de processos na indústria do petróleo

The petrochemical industry has as objective obtain, from crude oil, some products with a higher commercial value and a bigger industrial utility for energy purposes. These industrial processes are complex, commonly operating with large production volume and in restricted operation conditions. The operation control in optimized and stable conditions is important to keep obtained products quality and the industrial plant safety. Currently, industrial network has been attained evidence when there is a need to make the process control in a distributed way. The Foundation Fieldbus protocol for industrial network, for its interoperability feature and its user interface organized in simple configuration blocks, has great notoriety among industrial automation network group. This present work puts together some benefits brought by industrial network technology to petrochemical industrial processes inherent complexity. For this, a dynamic reconfiguration system for intelligent strategies (artificial neural networks, for example) based on the protocol user application layer is proposed which might allow different applications use in a particular process, without operators intervention and with necessary guarantees for the proper plant functioning

Avaliação de produtos naturais no controle de biofilmes formados em sistema dinâmico

The biofilms microbial forms of association are responsible for generating, accelerating and / or induce the process of corrosion. The damage generated in the petroleum industry for this type of corrosion is significatives, representing major investment for your control. The aim of this study was to evaluate such tests antibiograms the effects of extracts of Jatropha curcas and essential oil of Lippia gracilis Schauer on microrganisms isolated from water samples and, thereafter, select the most effective natural product for further evaluation of biofilms formed in dynamic system. Extracts of J. curcas were not efficient on the complete inhibition of microbial growth in tests type antibiogram, and essential oil of L. gracilis Schauer most effective and determined for the other tests. A standard concentration of essential oil of 20 μL was chosen and established for the evaluation of the biofilms and the rate of corrosion. The biocide effect was determined by microbial counts of five types of microorganisms: aerobic bacteria, precipitating iron, total anaerobic, sulphate reducers (BRS) and fungi. The rate of corrosion was measured by loss of mass. Molecular identification and scanning electron microscopy (SEM) were performed. The data showed reduction to zero of the most probable number (MPN) of bacteria precipitating iron and BRS from 115 and 113 minutes of contact, respectively. There was also inhibited in fungi, reducing to zero the rate of colony-forming units (CFU) from 74 minutes of exposure. However, for aerobic and anaerobic bacteria there was no significant difference in the time of exposure to the essential oil, remaining constant. The rate of corrosion was also influenced by the presence of oil. The essential oil of L. gracilis was shown to be potentially effective

Estimação e compensação de não linearidades inerentes aos atuadores dos processos industriais

The oscillations presents in control loops can cause damages in petrochemical industry. Canceling, or even preventing such oscillations, would save up to large amount of dollars. Studies have identified that one of the causes of these oscillations are the nonlinearities present on industrial process actuators. This study has the objective to develop a methodology for removal of the harmful effects of nonlinearities. Will be proposed an parameter estimation method to Hammerstein model, whose nonlinearity is represented by dead-zone or backlash. The estimated parameters will be used to construct inverse models of compensation. A simulated level system was used as a test platform. The valve that controls inflow has a nonlinearity. Results and describing function analysis show an improvement on system response

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Efeito de preparações de produtos naturais (cravo da índia e tomate) e de um produto sintético na marcação de constituintes sangüineos com tecnécio-99m e na morfologia de hemácias isoladas de sangue de ratos wistar

There are strong interests in the evaluation of the biological effects of natural and synthetic products. Blood constituents labeled with technetium-99m (99mTc) are used in nuclear medicine. The aim of this work was to study the effects of Clove (Caryophyllus aromaticas L.) and OZE (preparation used in the Health Sciences) on the labeling blood constituents with 99mTc and on the morphologic red blood cells (RBC) and the action of an extract of tomato (TO) on the labeling of blood constituents Blood samples were incubated with clove or OZE or TO, stannous chloride and 99mTc. Plasma (P), blood cells (BC), insoluble fractions (IF) of plasma and blood cells were separated. The radioactivity was counted and percentage of radioactivity (%ATI) to each blood fraction was calculated. The shape and morphometric parameter (perimeter/area ratio) were evaluated in the studies with clove and OZE. Clove extract and OZE altered significantly (p<0.05) the %ATI of blood constituents and the shape of red blood cells. However, clove extract not altered the red blood cells perimeter/area ratio. The tomato extract used at the highest concentrations reduced significantly (p<0.05) the %ATI in IF-P, although this extract did not modify the radiolabeling on BC, neither the radioactivity fixation on IFBC. The results indicate that these chemical compounds would have oxidative/chelating actions

Avaliação in vitro da eficácia de produtos homeopáticos contendo momordica charantia através de bioensaios

Homeopathic medicines have been used for over two hundred years without the examination of their effects on in vivo and in vitro assays, due to the peculiarity of homeopathic preparations, the high dilution, which creates a challenge for the use of usual analytical techniques of quality control of medicine.Although there is scarcity of literature and variety of experiments, recently there have been some studies with few in vitro assays which have shown positive responses when evaluating the mechanism of action of homeopathic medicines which are able to act on a specific system.The present study aims to evaluate the efficacy of homeopathic products containing Momordica charantia through bioassays.Homeopathic products were tested by the MTT to assess cytotoxicity in RAW 264.7 (macrophage-like cells) and in tumor cells HeLa (human cervical adenocarcinoma cells), CHO K1 (Chinese hamster ovary cells), PANC-1 (human pancreas cancer cells) and PC-3 (human prostate cancer cells), dosage of inflammatory mediators NO, TNF-α and IL-6 released by RAW 264.7 cells, analysis of the death process and cell cycle changes of PC-3 by flow cytometry. The data demonstrate that homeopathic products of Momordica charantia did not show cytotoxicity to RAW 264.7, increased the production of inflammatory mediators by RAW 264.7 synergistically with LPS, showed cytotoxicity to PC-3 with change in its cell cycle inhibiting its proliferation, being the 30CH the most potent sample. Correlation studies were conducted in order to evaluate the possible in vitro applicable models to the quality control of homeopathic products with Momordica charantia. The data showed that the best applicable models in assessing the quality are the MTT to assess cytotoxicity in RAW 264.7 and PC-3 in 24 hours for Momordica charantia fruit products and dosage of NO production by RAW 264.7 with and without LPS

Contribuições sobre estudos térmicos (TG/DTG, DTA, DSC e DSC-Fotovisual) da rifampicina e seus principais produtos de degradação

Since its synthesis over 48 years rifampicin has been extensively studied. The literature reports the characterization of thermal events for rifampicin in nitrogen atmosphere, however, no characterization in synthetic air atmosphere. This paper aims to contribute to the thermal study of rifampicin through thermal (TG / DTG, DTA, DSC and DSC - FOTOVISUAL ) and non-thermal (HPLC, XRPD , IR - FTIR , PCA) and its main degradation products ( rifampicin quinone , rifampicin N-oxide 3- formylrifamicin). Rifampicin study was characterized as polymorph form II from techniques DSC, IR and XRPD. TG curves for rifampicin in synthetic air atmosphere showed higher thermal stability than those in N2, when analyzed Ti and Ea. There was characterized as overlapping events melting and recrystallization under N2 with weight loss in the TG curve, suggesting concomitant decomposition. Images DSCFotovisual showed no fusion event and showed darkening of the sample during analysis. The DTA curve in synthetic air atmosphere was visually different from DTA and DSC curves under N2, suggesting the absence of recrystallization and melting or presence only decomposition. The IV - FTIR analysis along with PCA analysis and HPLC and thermal data suggest that rifampicin for their fusion is concomitant decomposition of the sample in N2 and fusion events and recrystallization do not occur in synthetic air atmosphere. Decomposition products studied in an air atmosphere showed no melting event and presented simultaneously to the decomposition initiation of heating after process loss of water and / or solvent, varying the Ti initiating events. The Coats - Redfern , Madsudhanan , Van Krevelen and Herwitz - Mertzger kinetic parameters for samples , through the methods of OZAWA , in an atmosphere of synthetic air and / or N2 rifampicin proved more stable than its degradation products . The kinetic data showed good correlation between the different models employed. In this way we contribute to obtaining information that may assist studies of pharmaceutical compatibility and stability of substances

Reconfigurações industriais das regiões metropolitanas do Nordeste: uma análise a partir do emprego formal

Industrial development experienced by Brazil from the 1950s, changed the concentration of population in the country. The process of development of domestic industry, concentrated in urban areas, crowded growing portion of the population.The Southeast region during the first stage of industrialization driven by the state, with the implementation of Plan goals, captained the major industrial projects implemented in the period and became the main industrial center of the country.In the decade from 1960 to 1980 the state action was marked by numerous regional development projects, softening the industrial concentration and Brazilian investment redirected to the Northeast.The second National Development Plan implemented in the 1970s led to major investments Northeast.This period marked the widespread urban growth and institutionalization of the first metropolitan areas in Brazil.The change of this developmental process is altered with the fiscal and financial crisis of the state in the 1980s and 1990s and spending cuts aimed at national development, reorienting the economy to liberal policies of economic liberalization and reduction of activity in the economy.Industrial policy was relegated to local development plans from the 1990s to the federating units fitting the wide use of tax incentives, the "war tax" to the continued industrialization process.In this context of the national economy work seeks to analyze the industrial setting in the metropolitan areas of Fortaleza, Recife and Salvador between 1995 and 2010.Although the metropolitan areas of Fortaleza, Recife and Salvador are the main urban centers of the Northeast, responsible for the advancement of industrial development, reconfigurations occurred between 1995 and 2010 by changing the level of industrial specialization built by regional division of labor in these regions.The work will be carried out by the method of descriptive analysis of the literature review on regional and urban development.Constitute quantitative method as the secondary data analysis of formal employment from the Annual Social Information (RAIS) Ministry of Labour and Employment (MTE).Using data RAIS / MTE analyzes the industrial specialization index using the Locational Quotient (LQ).Thus, it is assumed as a parameter analysis QL> 1, when the region has become specialized in a particular sector or QL <1, when the region does not have expertise in industrial sector analyzed.The conclusion of study indicates that there was in these metropolitan areas maintained the same bias hub.Fiscal policies, the states, was not successful in diversifying the productive structure and the Northeast region itself.This result is demonstrated by the need and dependence on state investments in the region to promote development.Industrial policies of recent years have been positive to meet the objectives of employment generation, but there must be specific policies for better diversification of production, in addition to integrating the economy of the Northeast sector and regionally

Interação tritrófica e influência de produtos químicos e vegetais no complexo: brássicas x traça-das-crucíferas x parasitóides de ovos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de equipamento motorizado para aplicação líquida de produtos fitossanitários na cultura do café

O trabalho teve como objetivo desenvolver um protótipo aplicador de líquidos na superfície do solo para cafezais localizados em regiões de topografia acidentada ou cultivados em sistema de plantio adensado. O protótipo do aplicador construído é um trator de rabiças acionado por um motor de dois tempos a gasolina, de 2,61 kW (3,5 cv), com duas rodas motrizes com bitola de 0,60 m e uma terceira roda direcional, equipado com sistema de pulverização dotado de depósito de 40 L, bomba centrífuga, filtros de linha, regulador de pressão, manômetro, mangueiras, válvulas e suporte de bicos. Para avaliar a eficiência do protótipo, foram instalados dois experimentos de campo em São Sebastião do Paraíso - MG (2003 e 2004), onde foram aplicados inseticidas sistêmicos para o controle da cigarra. Os métodos de aplicação avaliados foram: aplicação em faixa, filete, drench contínuo e drench intermitente. O protótipo aplicador de líquidos à superfície do solo atendeu aos objetivos propostos, visto que conseguiu realizar o controle químico de cigarras com destaque para a aplicação em drench contínuo. O protótipo, se equipado para aplicar simultaneamente nos dois lados da planta, apresentará capacidade de campo operacional semelhante à do equipamento tratorizado.