Obtenção de biodiesel por transesterificação em dois estágios e sua caracterização por cromatografia gasosa: óleos e gorduras em laboratório de química orgânica

Methanolic transesterification of oils and fats was carried out in a two steps procedure, under basic and acidic catalysis. Palm, soybean, canola, corn, rice, grapeseed, sunflower, peanut, pequi and olive oils, besides tallow and lard were used as feedstock. Specific gravity, relative viscosity, thin layer chromatography and gas chromatography were used to characterize the biodiesel. Biodiesel was obtained in high yield and purity. Results were used to discuss the following key-concepts: 1 - triglycerides, composition and properties; 2 - nucleophilic acyl substitution under basic and acid conditions, 3 - thin layer chromatography, 4 - gas chromatography and its quantitative methods.

Análise do teor e da qualidade dos lipídeos presentes em sementes de oleaginosas por rmn de baixo campo

To choose among the variety of oleaginous plants for biodiesel production, the oil content of several matrices was determined through different low-field ¹H nuclear magnetic resonance (NMR) experiments with varied pulse sequences, namely single-pulse, spin-echo, CPMG, and CWFP. The experiments that involved the first three sequences showed high correlation with each other and with the solvent extraction method. The quality of the vegetable oils was also evaluated on the basis of the existing correlation between the T2 values of the oils and their properties, such as viscosity, iodine index, and cetane index. These analyses were performed using HCA and PCA chemometric tools. The results were sufficiently significant to allow separation of the oleaginous matrices according to their quality. Thus, the low-field ¹H NMR technique was confirmed as an important tool to aid in the selection of oleaginous matrices for biodiesel production.

Influencia de variables de formulación en la viscosidad de emulsiones de surfactante aniónico-aceite-agua

Phase transition and viscosity behavior of emulsified systems were studied after modifying their physicochemical formulation. Effects of concentration and nature of salts and n-alcohols, and water/oil relation on the rheological properties of emulsions were also studied. Pre-equilibrated systems were emulsified according to an agitation procedure, and the viscosity (cP) was measured at different shear rates ranging from 1 to 300 s-1. The phase behavior, as well as the emulsion type based on electrolytic conductivity, was observed. Several interpretations of the flow and viscosity curves of emulsions were made through the estimation of rheological parameters such as consistency index "k" and behavior index "n".

INFLUÊNCIA DO CATALISADOR EM SOLUÇÕES POLIMÉRICAS PARA O PREPARO DE GÉIS ORGÂNICOS DE RESORCINOL-FORMALDEÍDO

Resorcinol-formaldehyde (RF) organic gels have been extensively used to produce carbon aerogels. The organic gel synthesis parameters greatly affect the structure of the resulting aerogel. In this study, the influence of the catalyst quantity on the polymeric solution sol-gel process was investigated. Sodium carbonate was used as a basic catalyst. RF gels were synthesized with a resorcinol to formaldehyde molar ratio of 0.5, a resorcinol to catalyst (R/C) molar ratio equal to 50 or 300, and a resorcinol to solvent ratio of 0.1 g mL-1. The sol-gel process was evaluated in situ by Fourier transform infrared spectroscopy using a universal attenuated total reflectance sensor and measurements of the kinematic viscosity. The techniques showed the evolution of the sol-gel process, and the results showed that the lower catalyst quantity induced a higher gel point, with a lower viscosity at the gel point. Differential scanning calorimetry was used to investigate the thermal behavior of the RF dried gel, and results showed that the exothermic event related to the curing process was shifted to higher temperatures for solutions containing higher R/C ratios.

INTERACTIONS: DESIGN, IMPLEMENTATION AND EVALUATION OF A COMPUTATIONAL TOOL FOR TEACHING INTERMOLECULAR FORCES IN HIGHER EDUCATION

Intermolecular forces are a useful concept that can explain the attraction between particulate matter as well as numerous phenomena in our lives such as viscosity, solubility, drug interactions, and dyeing of fibers. However, studies show that students have difficulty understanding this important concept, which has led us to develop a free educational software in English and Portuguese. The software can be used interactively by teachers and students, thus facilitating better understanding. Professors and students, both graduate and undergraduate, were questioned about the software quality and its intuitiveness of use, facility of navigation, and pedagogical application using a Likert scale. The results led to the conclusion that the developed computer application can be characterized as an auxiliary tool to assist teachers in their lectures and students in their learning process of intermolecular forces.

Separation of Gas Bubbles from Circulation Waters and Pulp Suspensions in Open Channel Flow

The objective of this thesis was to study the removal of gases from paper mill circulation waters experimentally and to provide data for CFD modeling. Flow and bubble size measurements were carried out in a laboratory scale open gas separation channel. Particle Image Velocimetry (PIV) technique was used to measure the gas and liquid flow fields, while bubble size measurements were conducted using digital imaging technique with back light illumination. Samples of paper machine waters as well as a model solution were used for the experiments. The PIV results show that the gas bubbles near the feed position have the tendency to escape from the circulation channel at a faster rate than those bubbles which are further away from the feed position. This was due to an increased rate of bubble coalescence as a result of the relatively larger bubbles near the feed position. Moreover, a close similarity between the measured slip velocities of the paper mill waters and that of literature values was obtained. It was found that due to dilution of paper mill waters, the observed average bubble size was considerably large as compared to the average bubble sizes in real industrial pulp suspension and circulation waters. Among the studied solutions, the model solution has the highest average drag coefficient value due to its relatively high viscosity. The results were compared to a 2D steady sate CFD simulation model. A standard Euler-Euler k-ε turbulence model was used in the simulations. The channel free surface was modeled as a degassing boundary. From the drag models used in the simulations, the Grace drag model gave velocity fields closest to the experimental values. In general, the results obtained from experiments and CFD simulations are in good qualitative agreement.

Holocene Varved Lake Sediments as Records of Palaeoenvironmental Change and Geomagnetic Palaeosecular Variation in Eastern Finland

This dissertation discusses Holocene palaeoenvironmental and palaeomagnetic secular variation (PSV) records reconstructed from sediments preserved in Lake Lehmilampi (63º37´N, 29º06´E) and Lake Kortejärvi (63º37´N, 28º56´E) in eastern Finland. Several piston and freeze cores were obtained from both lakes for varve and magnetic analyses. Sediment samples were impregnated in low-viscosity epoxy and physical parameters of varves, including varve thickness and relative grey-scale values, were recorded using x-ray densitometry combined with semiautomatic digital image analysis. On average, varve records of Lehmilampi and Kortejärvi cover 5122 and 3902 years, respectively. Past solar activity, as estimated by residual ₁₄C data, compares favourably with varve thicknesses from Lehmilampi during the last 2000 years. This indicates the potential of clastic-organic varves to record sensitively climatic variations. Bulk magnetic parameters, including magnetic susceptibility together with natural, anhysteretic and isothermal remanent magnetizations, were measured to describe mineral magnetic properties and geomagnetic palaeosecular variation recorded in the sediments. Main stages in the development of the investigated lakes are reflected in the variations in the mineral magnetic records, sediment lithology and composition. Similar variations in magnetic parameters and sediment organic matter suggest contribution of bacterial magnetite in the magnetic assemblages of Lehmilampi. Inclination and relative declination records yielded largely consistent results, attesting to the great potential of these sediments to preserve directional palaeosecular variation in high resolution. The PSV data from Lehmilampi and Kortejärvi were stacked into North Karelian PSV stack, which may be used for dating homogenous lake sediments in the same regional context. Reconstructed millennial variations in relative palaeointensity results are approximately in agreement with those seen in the absolute palaeointensity data from Europe. Centennial variations in the relative palaeointensity, however, are influenced by environmental changes. Caution is recommended when using varved lake sediments in reconstructing relative palaeointensity.

Lämpötilan vaikutus kuparin ja nikkelin kolonnierotuksessa kelatoivalla adsorbentilla

Sinkin valmistuksessa pitää sinkkirikasteesta poistaa epäpuhtausmetallit ennen elektrolyysiä. Nykyisin epäpuhtauksien poistamiseksi käytetään sementointimene-telmiä. Sementointi voisi olla mahdollista korvata kelatoivalla adsorbentilla suori-tettavalla erotuksella, jonka etuja ovat selektiivisyys ja ympäristöystävällisyys. Työn tarkoituksena on tutkia lämpötilan vaikutusta kelatoivalla adsorbentilla teh-tävään nikkelin ja kuparin kolonnierotukseen. Kolonnierotuksessa lämpötila voi vaikuttaa sekä liuoksen että adsorbentin fysi-kaalisiin, kemiallisiin ja sähkökemiallisiin ominaisuuksiin. Näiden vaikutusten johdosta voivat esimerkiksi erotuksen stoikiometria, kinetiikka tai toimintaolosuh-teet muuttua. Tässä työssä lämpötilan vaikutusta kolonnierotukseen tutkittiin rik-kihapon ja erotusmateriaalin välisillä kinetiikkakokeilla sekä synteettisellä CuSO4-liuoksella ja autenttisella ZnSO4-liuoksella tehdyillä kolonniajoilla. Työssä käytetyn erotusmateriaalin runko on silikapolyamiini ja sen funktionaali-sena ryhmänä toimii 2-aminometyylipyridiini. Lämpötilan ollessa 60 °C havaittiin erotusmateriaalin ja rikkihapon asettuvan tasapainoon kolme kertaa nopeammin kuin 25 °C:ssa. Lämpötilan nostamisella edelleen 90 °C:een ei havaittu olevan merkittävää vaikutusta tasapainon saavuttamisen nopeuteen. Kuparin läpäisykäyrän havaittiin jyrkentyvän lämpötilan noston vaikutuksesta niin autenttisella ZnSO4-liuoksella kuin synteettisellä CuSO4-liuoksella. Tämän oletettiin johtuvan kinetiikan nopeuden kasvusta sekä autenttisella liuoksella myös viskositeetin pienenemisestä. Lämpötilan vaikutuksesta on mahdollista käsitellä autenttista ZnSO4-liuosta 90 °C:ssa noin 3,5-kertaa enemmän kuin 25 °C:ssa, siten että liuoksesta saadaan poistettua lähes kaikki kupari. Nikkelin havaittiin lä-päisevän kolonnin kaikissa lämpötiloissa lähes välittömästi. Tästä syystä tutkittu erotusmateriaali ei sovellu nikkelin ja kuparin samanaikaiseen erottamiseen tutki-tusta autenttisesta ZnSO4-liuoksesta.

Production of biodiesel from babassu oil using methanol-ethanol blends

Maranhão state in Brazil presents a big potential for the cultivation of several oleaginous species, such as babassu, soybean, castor oil plant, etc... These vegetable oils can be transformed into biodiesel by the transesterification reaction in an alkaline medium, using methanol or ethanol. The biodiesel production from a blend of these alcohols is a way of adding the technical and economical advantages of methanol to the environmental advantages of ethanol. The optimized alcohol blend was observed to be a methanol/ethanol volume ratio of 80 % MeOH: 20 % EtOH. The ester content was of 98.70 %, a value higher than the target of the ANP, 96.5 % (m/m), and the biodiesel mass yield was of 95.32 %. This biodiesel fulfills the specifications of moisture, specific gravity, kinematic viscosity and percentages of free alcohols (methanol plus ethanol) and free glycerin.

Viscometric investigations and molecular interactions of some derivatives of 5-substituted indole dihydropyrimidines in mixed organic solvents

Colloid chemical behavior of indole dihydropyrimidines in non-aqueous solvent mixture benzene-methanol of varying composition has been investigated by viscometric measurements at 303K± 0.1. The viscosity of the system increases with the increase in concentration. The Trend Change Point (TCP) values have been determined by intersection of two straight lines, which are found to be dependent on the composition of solvent mixtures. The study confirms that the nature of synthesized compounds agglomerate formed below and above 50% benzene concentration is quite different. The viscometric data have been analyzed in terms of Einstein, Vand, Moulik and Jones-Dole equations. These well known equations have been successfully applied to explain the results of viscosity measurements and the viscometric parameters show that the behavior of compound changes in the proximity of 50% benzene concentration.

On the potential utilisation of sawdust and wood chip screenings

This work is based on the utilisation of sawdust and wood chip screenings for different purposes. A substantial amount of these byproducts are readily available in the Finnish forest industry. A black liquor impregnation study showed that sawdust-like wood material behaves differently from normal chips. Furthermore, the fractionation and removal of the smallest size fractions did not have a significant effect on the impregnation of sawdust-like wood material. Sawdust kraft cooking equipped with an impregnation stage increases the cooking yield and decreases the lignin content of the produced pulp. Impregnation also increases viscosity of the pulp and decreases chlorine dioxide consumption in bleaching. In addition, impregnation increases certain pulp properties after refining. Hydrotropic extraction showed that more lignin can be extracted from hardwood than softwood. However, the particle size had a major influence on the lignin extraction. It was possible to extract more lignin from spruce sawdust than spruce chips. Wood chip screenings are usually combusted to generate energy. They can also be used in the production of kraft pulp, ethanol and chemicals. It is not economical to produce ethanol from wood chip screenings because of the expensive wood material. Instead, they should be used for production of steam and energy, kraft pulp and higher value added chemicals. Bleached sawdust kraft pulp can be used to replace softwood kraft pulp in mechanical pulp based papers because it can improve certain physical properties. It is economically more feasible to use bleached sawdust kraft pulp in stead of softwood kraft pulp, especially when the reinforcement power requirement is moderate.

Crystallization characteristics of bioactive glasses

Bioactive glasses are excellent candidates for implant materials, because they can form a chemical bond to bone or guide bone growth, depending on the glass composition. Some compositions have even shown soft tissue attachment and antimicrobial effects. So far, most clinical applications are based on monoliths, plates and particulates of different grain sizes. There is a growing interest in special products such as porous implants sintered from microspheres and fibers drawn from preforms or glass melts. The viscosity range at which these are formed coincides with the crystallization temperature range for most bioactive glasses, thus complicating the manufacturing process. In this work, the crystallization tendency and its kinetics for a series of glasses with their compositions within the range of bioactivity were investigated. The factors affecting crystallization and how it is related to composition were studied by means of thermal analysis and hot stage microscopy. The crystal compositions formed during isothermal and non-isothermal heat treatments were analyzed with SEM-EDXA and X-ray diffraction analysis. The temperatures at which sintering and fiber drawing can take place without interfering with crystallization were determined and glass compositions which are suitable for these purposes were established. The bioactivity of glass fibers and partly crystallized glass plates was studied by soaking them in simulated body fluid (SBF). The thickness of silica, calcium and phosphate rich reaction layers on the glass surface after soaking was used as an indication of the bioactivity. The results indicated that the crystallization tendencies of the experimental glasses are strongly dependent on composition. The main factor affecting the crystallization was found to be the alkali oxide content: the higher the alkali oxide content the lower the crystallization temperature. The primary crystalline phase formed at low temperatures in these glasses was sodium calcium silicate. The crystals were found to form through internal nucleation, leading to bulk crystallization. These glasses had high bioactivity in vitro. Even when partially crystalline, they formed typical reaction layers, indicating bioactivity. In fact, sodium calcium silicate crystals were shown to transform in vitro into hydroxyapatite during soaking. However, crystallization should be avoided because it was shown to retard dissolution, bioactivity reactions and complicate fiber drawing process. Glass compositions having low alkali oxide content showed formation of wollastonite crystals on the surface, at about 300°C above the glass transition temperature. The wide range between glass transition and crystallization allowed viscous flow sintering of these compositions. These glasses also withstood the thermal treatments required for fiber drawing processing. Precipitation of calcium and phosphate on fibers of these glasses in SBF suggested that they were osteoconductive. Glasses showing bioactivity crystallize easily, making their hot working challenging. Undesired crystallization can be avoided by choosing suitable compositions and heat treatment parameters, allowing desired product forms to be attained. Small changes in the oxide composition of the glass can have large effects and therefore a thorough understanding of glass crystallization behavior is a necessity for a successful outcome, when designing and manufacturing implants containing bioactive glasses.

Did Jesus cite Isa 6:9-10? : Jesus’ saying in Mark 4:11-12 and the Isaianic idea of hardening and remnant

Mark 4:11-12 innehåller en av Jesu mest gåtfulla utsagor. När Jesus citerar Jes 6:9-10, ser det ut som om han skulle mena att han använder liknelserna för att hindra vissa människor att förstå vad han säger, ända därhän att de därigenom utesluts från möjligheten att göra bättring och att få förlåtelse av Gud. Men utryckte Jesus sig verkligen på detta sätt? Formulerades inte utsagan snarare av den tidiga kyrkan eller evangelisten? Eller gav utsagan - vare sig den härstammade från Jesus eller kyrkan - från början alls uttryck åt tanken att liknelserna hade en förstockande funktion? Under mera än ett århundrade har forskarna ställt frågor av detta slag. Denna forskning syftar till att undersöka om man kan finna en plausibel jesuansk mening hos utsagan. Den utgår från förutsättningen att den mening och funktion som man gav åt Jes 6:9-10 i den palestinska, judiska kontexten under andra Templets period är avgörande för att hitta en jesuansk mening hos utsagan.

Seriedebatt i 1950-talets Finland : en studie i barndom, media och reglering

I avhandlingen granskas den debatt som fördes om seriemediet och serieläsandet i Finland från början av 1950-talet till början av 1960-talet. Serietidningen var då ett nytt medium och föranledde en oro beträffande barns läsvanor. ”Seriefrågan” diskuterades i pressen och problematiken engagerade barnskyddsorganisationer och forskare, behandlades i riksdagen och undersöktes av en statlig kommitté. De olika debattuttrycken analyseras i studien. Avhandlingens teoretiska perspektiv är styrningsanalytiskt och bygger på diskussionen om regementalitet (governmentality). I studien granskas hur seriemediet, barndom och regleringen av dessa kom att definieras i behandlingen av det s.k. serieproblemet. Serierna definierades som ett problematiskt medium på ett flertal sätt. De huvudsakliga argumenten mot serierna var dels att de förstörde barns läsförmåga, dels att de budskap som serierna förmedlade till barnen var av fel slag. Enligt kritiken var serierna språkligt fattiga och innehållsmässigt alltför våldsamma. Följaktligen utgjorde serierna ett hot mot barnen. Barnen kom ur detta perspektiv att definieras som inkompetenta medieanvändare och i behov av skydd. I debatten upplyftes olika sätt att lösa och reglera problemet. Man undersökte problematiken och upplyste allmänheten om den, man försökte påverka serieutgivarna och man påkallade censur. Seriedebatten och den verksamhet som debattörerna ägnade sig åt ledde dock inte till synbara resultat, t.ex. ny lagstiftning eller förändringar i seriemarknaden. Ändå dog debatten i början av 1960-talet. Problemet med de serieläsande barnen hanterades m.a.o. genom själva debatten. Samtidigt uteblev mera drastiska former av reglering. Ett övergripande syfte för analysen av den kunskap som skapades i debatten – dess varierande förståelse av seriemedium, barndom och reglering – är att erbjuda infallsvinklar till aktuella diskussioner om och farhågor angående barns mediebruk. Med fokus på bredden hos debattens uttryck och de diskursiva ramarna för problematiseringen av barns serieläsande ger avhandlingen perspektiv på den med jämna mellanrum uppdykande frågeställningen om barns mediebruk.

Kuituvuoto reikäsihdillä massan syöttövaiheessa

Diplomityön tarkoituksena oli kehittää tutkimuslaite, jolla pystyttäisiin tutkimaan sellumassan syöttötapahtumaa reikäsihdillä ja tarkastelemaan syöttöhetkellä tapahtuvaa kuituhäviötä. Laitteen suunnittelun ja valmistuksen tavoitteena oli myös saada tutkimuslaite mahdollisim-man modifioitavaksi (syöttöaukon koko, muoto ja erityyppiset reikäsihdit ja näiden vaikutukset sellukuitujen hävikkiin). Haluttiin myös mahdollisuus syöttötapahtuman kuvaamiseen esim. suurnopeuskameroin, joka otettiinkin huomioon laiteosia valittaessa (läpinäkyvä akryyli). Tutkimuslaitteen kestävyyttä erilaisissa prosessiolosuhteissa haluttiin korostaa (voidaan operoida laajalla pH ja lämpötila-alueilla, sekä syöttöpainetta voidaan muunnella). Diplomityön kirjallisuusosassa käsitellään kuituvuodon aiheuttamia haittoja, joista tärkein on taloudellinen menetys. Näiden lisäksi kirjallisuusosassa tarkastellaan pääpirteittäin pesume-netelmiä ja käydään läpi kuitusulpun suotautumiseen vaikuttavia tekijöitä. Diplomityöhön sisältyi tutkimuslaitteen suunnittelun ja valmistuksen lisäksi myös laitteen toi-mivuuden testaus. Testit suoritettiin pohjoismaisella koivusellulla. Koivusellu otettiin happi-vaiheen jälkeisen pesurin poistosta. Massalle suoritettiin KAPPA-luvun, SR-luvun, viskositee-tin ja syrjäytys -määritykset, sekä kuituanalyysi. Laitteella suoritettiin 7 %, 10 % ja 12 % sakeuksisten massojen koeajotestit. Suodokset otettiin talteen jatkotutkimuksiin, jossa niistä mitattiin kuituvuoto. 10 % suodokselle suoritettiin myös kuituanalyysi. Tuloksista nähtiin, että 7 % sakeuksinen massa antoi lähes nelinkertaisen kuituvuotomäärän 10 % sakeuksiseen massan syöttöön nähden.