Symphony No. 38, K.504

Soitinnus: Ork.

Another Look at the Null of Stationary Real Exchange Rates: Panel Data with Structural Breaks and Cross-section Dependence

This paper re-examines the null of stationary of real exchange rate for a panel of seventeen OECD developed countries during the post-Bretton Woods era. Our analysis simultaneously considers both the presence of cross-section dependence and multiple structural breaks that have not received much attention in previous panel methods of long-run PPP. Empirical results indicate that there is little evidence in favor of PPP hypothesis when the analysis does not account for structural breaks. This conclusion is reversed when structural breaks are considered in computation of the panel statistics. We also compute point estimates of half-life separately for idiosyncratic and common factor components and find that it is always below one year.

Calculation of the critical crack size for cold form rectangular hollow section tube (CRHS) under bending load at -40º C temperature

To predict the capacity of the structure or the point which is followed by instability, calculation of the critical crack size is important. Structures usually contain several cracks but not necessarily all of these cracks lead to failure or reach the critical size. So, defining the harmful cracks or the crack size which is the most leading one to failure provides criteria for structure’s capacity at elevated temperature. The scope of this thesis was to calculate fracture parameters like stress intensity factor, the J integral and plastic and ultimate capacity of the structure to estimate critical crack size for this specific structure. Several three dimensional (3D) simulations using finite element method by Ansys program and boundary element method by Frank 3D program were carried out to calculate fracture parameters and results with the aid of laboratory tests (loaddisplacement curve, the J resistance curve and yield or ultimate stress) leaded to extract critical size of the crack. Two types of the fracture which is usually affected by temperature, Elastic and Elasti-Plastic fractures were simulated by performing several linear elastic and nonlinear elastic analyses. Geometry details of the weldment; flank angle and toe radius were also studied independently to estimate the location of crack initiation and simulate stress field in early stages of crack extension in structure. In this work also overview of the structure’s capacity in room temperature (20 ºC) was studied. Comparison of the results in different temperature (20 ºC and -40 ºC) provides a threshold of the structure’s behavior within the defined range.

L'Éveil du XXe : organe d'information locale édité par la section communiste

1941/05/01 (N14d).

L'Éveil du XXe : organe d'information locale édité par la section communiste

Variante(s) de titre : Éveil du vingtième (Paris)

L'Éveil du XXe : organe d'information locale édité par la section communiste

1941/05/01 (N14).

L'Éveil du XXe : organe d'information locale édité par la section communiste

1941/02/20 (N11).

L'Éveil du XXe : organe d'information locale édité par la section communiste

1943/08 (N1).

L'Éveil du XXe : organe d'information locale édité par la section communiste

1941 (N16).

L'Éveil du XXe : organe d'information locale édité par la section communiste

1940/12/27 (N9).

Reducing Manufacturing Costs of the Screen Dryer’s Hot Section by Design

In this thesis, the purpose was to find the cost distribution of the screen dryer and the largest cost factors. The hot section of the screen dryer was revealed as the biggest cost factor, so composing new cost efficient solutions were directed to it. DFMA (Design for Manufacture and Assembly) was chosen to help the design process. DFMA is a product design strategy developed for taking manufacturing and assembly costs into account at the early stages of the design process. In the theory part of the thesis, other methods of economical design and tools needed for estimating manufacturing costs are introduced. In the empirical part, the hot section of the screen dryer was divided into sub-assemblies and their manufacturing costs were estimated. The design propositions were directed to the self-manufactured assemblies and parts. The new manufacturing costs were calculated for the developed propositions. Lastly, the most cost efficient solutions were summarized. The savings on the self-manufactured assemblies were about 40 %, which was about 13 % of the combined total costs of the hot section.

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

THE SKEPTICAL CARTESIAN BACKGROUND OF HUME'S "OF THE ACADEMICAL OR SCEPTICAL PHILOSOPHY" (FIRST INQUIRY, SECTION 12)

ABSTRACT In section XII of the First Inquiry, Hume refers to the two Hellenistic schools of skepticism (Academic and Pyrrhonian) to present his own view of skepticism, which, however, depends on the ancient skeptics mainly indirectly. Hume's view of skepticism depends crucially on Descartes and post-Cartesian philosophers such as Pascal, Huet, Foucher and Bayle, who reacted skeptically to major Cartesian doctrines but followed one version or other of Descartes's methodical doubt. Although all these post-Cartesian philosophers are relevant in section XII, I focus on the topics in which Descartes himself-besides his skeptical followers-seems directly relevant. After an introductory section (I) on Julia Annas' and Richard Popkin's views of Hume's relation to, respectively, ancient and modern skepticism, I turn to section XII and examine what Hume calls (II) "consequent skepticism about the senses," (III) "antecedent skepticism," and (IV) "Academic skepticism."

Travels in various countries of Europe, Asia and Africa : Part the third : Scandinavia : Section the second : by Edward Daniel Clarke.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli

Travels in various countries of Europe, Asia and Africa : Part the third : Scandinavia : Section the first : by Edward Daniel Clarke.

Digital reproduction, The National Library of Finland, Centre for Preservation and Digitisation, Mikkeli