Flow injection green method for the quantitative analysis of ketoconazole in pharmaceutical preparations

A flow injection method for the quantitative analysis of ketoconazole in tablets, based on the reaction with iron (III) ions, is presented. Ketoconazole forms a red complex with iron ions in an acid medium, with maximum absorbance at 495 nm. The detection limit was estimated to be 1×10--4 mol L-1; the quantitation limit is about 3×10--4 mol L-1 and approximately 30 determinations can be performed in an hour. The results were compared with those obtained with a reference HPLC method. Statistical comparisons were done using the Student's t procedure and the F test. Complete agreement was found at the 0.95 significance level between the proposed flow injection and the HPLC procedures. The two methods present similar precision, i.e., for HPLC the mean relative standard deviation was ca. 1.2% and for FIA ca. 1.6%.

Chlorophenols in tap water from wells and surface sources in Rio de Janeiro, Brazil: method validation and analysis

Two analytical methods were validated for determination of trichlorophenols, tetrachlorophenols and pentachlorophenol in drinking water. Limits of quantification were at least ten times lower than maximum permissible levels set by the Brazilian legislation, which are 200 ng mL-1 for 2,4,6-trichlorophenol and 9 ng mL-1 for pentachlorophenol. Chlorophenol levels were determined in tap water collected in the Municipality of Rio de Janeiro. 2,4,6-Trichlorophenol residues were detected in 36% of the samples, varying from 0.008 to 0.238 ng mL-1. All other analytes were below the limit of quantification. The validated methods showed to be suitable for application in routine quality control.

Indirect spectrophotometric method for determination of captopril using Cr(VI) and diphenylcarbazide

A spectrophotometric method for the indirect determination of captopril (CP) in pharmaceutical formulations is proposed. The proposed procedure is based on the oxidation of captopril by potassium dichromate and the determination excess oxidant on the basis of its reaction with diphenylcarbazide (DPC). Under the optimum conditions, a good linear relationship (r = 0.9997) was obtained in the range of 0.08-3.5 µg mL-1. The assay limits of detection and quantitation were 0.024 and 0.08 µg mL-1, respectively. The results obtained for captopril determination in pharmaceuticals using the proposed method and those obtained with the US Pharmacopoeia method were in good agreement at the 95% confidence level.

Exploración estocástica de las superficies de energía potencial de dímeros cis-trans y trans-trans del ácido fórmico

Potential energy surface (PES) of cis-trans and trans-trans formic acid dimers were sampled using a stochastic method, and the geometries, energies, and vibrational frequencies were computed at B3LYP/6-311++G(3df,2p) level of theory. The results show that molar free energy of dimerization deviated up to 108.4% when basis set superposition error (BSSE) and zero-point energy (ZPE) were not considered. For cis-trans dimers, C=O and O - H bond weakened, whereas C - O bonds strengthened due to dimerization. Also, trans-trans FA dimers did not show a trend regarding strengthening or weakening of the C=O, O - H and C - O bonds.

Optimization of wind blade design including its energetic characteristics

The goal of the Master’s thesis is to develop and to analyze the optimization method for finding a geometry shape of classical horizontal wind turbine blades based on set of criteria. The thesis develops a technique that allows the designer to determine the weight of such factors as power coefficient, sound pressure level and the cost function in the overall process of blade shape optimization. The optimization technique applies the Desirability function. It was never used before in that kind of technical problems, and in this sense it can claim to originality of research. To do the analysis and the optimization processes more convenient the software application was developed.

A generalized 1D particle transport method for convection diffusion reaction model

This work is devoted to the development of numerical method to deal with convection diffusion dominated problem with reaction term, non - stiff chemical reaction and stiff chemical reaction. The technique is based on the unifying Eulerian - Lagrangian schemes (particle transport method) under the framework of operator splitting method. In the computational domain, the particle set is assigned to solve the convection reaction subproblem along the characteristic curves created by convective velocity. At each time step, convection, diffusion and reaction terms are solved separately by assuming that, each phenomenon occurs separately in a sequential fashion. Moreover, adaptivities and projection techniques are used to add particles in the regions of high gradients (steep fronts) and discontinuities and transfer a solution from particle set onto grid point respectively. The numerical results show that, the particle transport method has improved the solutions of CDR problems. Nevertheless, the method is time consumer when compared with other classical technique e.g., method of lines. Apart from this advantage, the particle transport method can be used to simulate problems that involve movingsteep/smooth fronts such as separation of two or more elements in the system.

Covalent anion of Li(HF)3- system: an ab initio study

In this paper, we report the stability of the Li(HF)3- molecular anion calculated at the MP2/6-31++G** and CCSD(T)/6-31++G** level of theory. Five possible conformers of Li(HF)3- molecular anions have been determined employing ab initio MP2 method with 6-31++G** basis set. The most stable conformer of five Li(HF)3- anions is in a cyclic ring structure Li(HF)3-(1). From our calculations we show that the molecule is stable towards electron attachment, with an electron adiabatic electron affinity (AEA) of 199.5 meV (233.1 meV with zero point energy correction) and 471.3 meV at the MP2 and CCSD(T) levels, respectively. In addition we present vertical detachment energies of 230.2 meV and 795.8 meV at the MP2, CCSD(T), respectively. The importance of the latter has to do with the ability of experimental detection of this value.

A simple spectrophotometric method for the determination of methyldopa using p-chloranil in the presence of hydrogen peroxide

A simple, rapid and sensitive spectrophotometric method has been developed for the determination of methyldopa in pharmaceutical formulations. The method is based on the reaction between tetrachloro-p-benzoquinone (p-chloranil) and methyldopa, accelerated by hydrogen peroxide (H2O2), producing a violet-red compound (λmax = 535 nm) at ambient temperature (25.0 ± 0.2 ºC). Experimental design methodologies were used to optimize the measurement conditions. Beer's law is obeyed in a concentration range from 2.10 x 10-4 to 2.48 x 10-3 mol L-1 (r = 0.9997). The limit of detection was 7.55 x 10-6 mol L-1 and the limit of quantification was 2.52 x 10-5 mol L-1. The intraday precision and interday precision were studied for 10 replicate analyses of 1.59 x 10-3 mol L-1 methyldopa solution and the respective coefficients of variation were 0.7 and 1.1 %. The proposed method was successfully applied to the determination of methyldopa in commercial brands of pharmaceuticals. No interferences were observed from the common excipients in the formulations. The results obtained by the proposed method were favorably compared with those given by the Brazilian Pharmacopoeia procedure at 95 % confidence level.

A novel indicator reaction for the catalytic determination of V(V) at ppb levels by the kinetic spectrophotometric method

A novel sensitive and relatively selective kinetic method is presented for the determination of V(V), based on its catalytic effect on the oxidation reaction of Ponceau Xylydine by potassium bromate in presence of 5-sulfosalicylic acid (SSA) as activator. The reaction was monitored spectrophotometrically by measuring the decrease in absorbance of Ponceau Xylydine at 640 nm between 0.5 to 7 min (the fixed time method) in H3PO4 medium at 25ºC. The effect of various parameters such as concentrations of H3PO4, SSA, bromate and Ponceau Xylydine, temperature and ionic strength on the rate of net reaction were studied. The method is free from most interferences, especially from large amounts of V(IV). The decrease in absorbance is proportional to the concentration of V(V) over the entire concentration range tested (1-15 ng mL−1) with a detection limit of 0.46 ng mL-1 (according to statistical 3Sblank/k criterion) and a coefficient of variation (CV) of 1.8% (for ten replicate measurement at 95% confidence level). The proposed method suffers few interferences such as Cr(VI) and Hg(II) ions. The method was successfully applied to the determination of V(V) in tap water, drinking water, bottled mineral water samples and a certified standard reference material such as SRM-1640 with satisfactory results. The vanadium contents of water samples were also determined by FAAS for a comparison. The recovery of spiked vanadium(V) was found to be quantitative and the reproducibility was satisfactory. It was observed that the results of the SRM 1640 were in good agreement with the certified value.

Determination of patulin in apple juice by HPLC using a simple and fast sample preparation method

The goal of this work was to develop a simple and rapid preparation method for patulin analysis in apple juice without previous clean-up. This method combined sonication and liquid extraction techniques and was used for determination of patulin in 37 commercial apple juices available on the market in the South of Brazil. The method performance characteristics were determined using a sample obtained in a local market fortified at five concentration levels of patulin and done in triplicates. The coefficient of variation for repeatability at the fortification level of 20.70µg.L-1 was 3.53 % and the recovery 94.63 %, respectively. The correlation coefficient was 0.9996 and agrees with the requirements for a linear analytical method value. The detection limit was 0.21µg.L-1 and the quantification limit 0.70 µg.L-1. Only three of the analyzed samples were upper the allowed level of 50.00 µg.L-1 recommended for the World Health Organization.

A simple spectrophotometric method for the determination of captopril in pharmaceutical preparations using ammonium molybdate

A simple, rapid and sensitive spectrophotometric method for the determination of captopril (CPT) in pharmaceutical formulations is proposed. This method is based on the reduction reaction of ammonium molybdate, in the presence of sulphuric acid, for the group thiol of CPT, producing a green compound (λ max 407 nm). Beer's law is obeyed in a concentration range of 4.60 x 10-4 - 1.84 x 10-3 mol l-1 of CPT with an excellent correlation coefficient (r = 0.9995). The limit of detection and limit of quantification were 7.31 x 10-6 e 2.43 x 10-5 mol l-1 of CPT, respectively. The proposed method was successfully applied to the determination of CPT in commercial brands of pharmaceuticals. No interferences were observed from the common excipients in the formulations. The results obtained by the proposed method were favorably compared with those given by the official reported method at 95 % confidence level.

A simple spectrophotometric method for the determination of tetracycline and doxycycline in pharmaceutical formulations using chloramine-T

A simple, rapid, accurate and inexpensive spectrophotometric method for the determination of tetracycline and doxycycline has been developed. The method is based on the reaction between these drugs and chloramine-T in alkaline medium producing red color products with absorbance maximum at the Λ = 535 and 525 nm for the tetracycline and doxycycline, respectively. The best conditions for the reactions have been found using multivariate method. Beer´s law is obeyed in a concentration ranges 1.03 x 10-5 to 3.61 x 10-4 mol L-1 and 1.75 x 10-5 to 3.48 x 10-4 mol L-1 for the tetracycline and doxycycline, respectively. The quantification limits were 5.63 x 10-6 mol L-1 and 7.12 x 10-7 mol L-1 for the tetracycline and doxycycline, respectively. The proposed method was successfully applied to the determination of these drugs in pharmaceutical formulations and the results obtained were in good agreement with those obtained by the comparative method at the 95% confidence level.

IDEAS for Strategic Technology Management: Design of an electronically mediated scenario method

The age-old adage goes that nothing in this world lasts but change, and this generation has indeed seen changes that are unprecedented. Business managers do not have the luxury of going with the flow: they have to plan ahead, to think strategies that will meet the changing conditions, however stormy the weather seems to be. This demand raises the question of whether there is something a manager or planner can do to circumvent the eye of the storm in the future? Intuitively, one can either run on the risk of something happening without preparing, or one can try to prepare oneself. Preparing by planning for each eventuality and contingency would be impractical and prohibitively expensive, so one needs to develop foreknowledge, or foresight past the horizon of the present and the immediate future. The research mission in this study is to support strategic technology management by designing an effective and efficient scenario method to induce foresight to practicing managers. The design science framework guides this study in developing and evaluating the IDEAS method. The IDEAS method is an electronically mediated scenario method that is specifically designed to be an effective and accessible. The design is based on the state-of-the-art in scenario planning, and the product is a technology-based artifact to solve the foresight problem. This study demonstrates the utility, quality and efficacy of the artifact through a multi-method empirical evaluation study, first by experimental testing and secondly through two case studies. The construction of the artifact is rigorously documented as justification knowledge as well as the principles of form and function on the general level, and later through the description and evaluation of instantiations. This design contributes both to practice and foundation of the design. The IDEAS method contributes to the state-of-the-art in scenario planning by offering a light-weight and intuitive scenario method for resource constrained applications. Additionally, the study contributes to the foundations and methods of design by forging a clear design science framework which is followed rigorously. To summarize, the IDEAS method is offered for strategic technology management, with a confident belief that it will enable gaining foresight and aid the users to choose trajectories past the gales of creative destruction and off to a brighter future.

On the development of object functions and restrictions for shapes made with a turret punch press

This study presents the information required to describe the machine and device resources in the turret punch press environment which are needed for the development of the analysing method for automated production. The description of product and device resources and their interconnectedness is the starting point for method comparison the development of expenses, production planning and the performance of optimisation. The manufacturing method cannot be optimized unless the variables and their interdependence are known. Sheet metal parts in particular may then become remarkably complex, and their automatic manufacture may be difficult or, with some automatic equipment, even impossible if not know manufacturing properties. This thesis consists of three main elements, which constitute the triangulation. In the first phase of triangulation, the manufacture occuring on a turret punch press is examined in order to find the factors that affect the efficiency of production. In the second phase of triangulation, the manufacturability of products on turret punch presses is examined through a set of laboratory tests. The third phase oftriangulation involves an examination of five industry parts. The main key findings of this study are: all possible efficiency in high automation level machining cannot be achieved unless the raw materials used in production and the dependencies of the machine and tools are well known. Machine-specific manufacturability factors for turret punch presses were not taken into account in the industrial case samples. On the grounds of the performed tests and industrial case samples, the designer of a sheet metal product can directly influence the machining time, material loss, energy consumption and the number of tools required on a turret punch press by making decisions in the way presented in the hypothesis of thisstudy. The sheet metal parts to be produced can be optimised to bemanufactured on a turret punch press when the material to be used and the kinds of machine and tool options available are known. This provides in-depth knowledge of the machine and tool properties machine and tool-specifically. None of the optimisation starting points described here is a separate entity; instead, they are all connected to each other.

The Process of Greening Cycle as Method of Operative Environmental

The structural change of society from product-based business to service- and further to need-based business has caused the fact that work for environmental issues has spread from conventional factories and environmentally harmful production to concern services and offices as well. Almost every company has an office, so a relatively small environmental burden caused by an individual office grows remarkable already at the state level and globally even more. Motivation to work for environmental issues in an individual office could be challenging even without the fact that wasted environmental impacts bound also wasted costs. Besides cost savings, a concretely greener image of a company has its value in the B2Cas well as in the B2B-field. Consumers and clients are more and more conscious of environmental issues and demand concrete actions instead of speeches, good thoughts and meaningless certifications. Internal work for environmental issues at a strategy level is not sufficient, so operational environmental management is needed for changing old practices. This research is about the effects of operative environmental management on the greening process of an office-based business. The research is outlined to concern the operative work in the office including field sales. Target was to concretely lower the environmental impacts of Lyreco Finland and to find cost savings directly by changing the operative practices in the office and also indirectly by affecting the level of environmental knowledge of the personnel. During the greening process, the aim was also to create concrete arguments for marketing as well. The circle of greening process, which was especially created for this diploma work, was used as a method. The circle divides a year to themes and sections separated by factors of environmental impacts. Separation is based on Brett Wills’ thoughts of seven green wastes (Wills, Brett. The Green Intensions. 2009) and follows it uneasily. The circle aimed at ensuring evolutionary growth of knowledge instead of being revolutionary in the changing process. Committing personnel to the process from its start by asking ideas from them and giving them clear directions was an important part of the research of operative management. Because of working from distance, communication with personnel was operated by frequent training days and weekly greening notes via emails and intranet. Also availability for communication was an important task because of the telecommuting. Research results of this work show that operative environmental management in an officebased business today is mostly management of change. When the strategic environmental friendliness is taken into a concrete level, the most important individual factor is motivating the operating personnel. Research shows that evolutionary change is found being an efficient way to make a change. Also understanding one´s own impact on the environmental burden and on the whole greening process clearly motivates the personnel. Results show that in the operative realization of the greening process, clear directions of new working practices, being as concrete as possible, and committing personnel to follow them make the process more effective. The operative environmental management and the cycle of the greening process decrease the environmental burden and save costs. The concrete results could be used as believable arguments in marketing and therefore exploited in communication with interest groups. Commitment of the management is also one of the key factors of success in the greening process. In this research, changes in the business field by a company trade took the focus of the management away from the greening process and made the process more inefficient by decreasing the amount of training days. The circle of greening process will be used as a tool in the future, as well, and therefore it will help observe environmental impacts of a company and increase sustainable development. Commitment of management to the evolutionary environmental work helps the operating personnel lower environmental impacts, decrease costs and build a concretely greener image.