Development of a Subgrade Drainage Model for Unpaved Roads, TR-654, 2015

With over 68 thousand miles of gravel roads in Iowa and the importance of these roads within the farm-to-market transportation system, proper water management becomes critical for maintaining the integrity of the roadway materials. However, the build-up of water within the aggregate subbase can lead to frost boils and ultimately potholes forming at the road surface. The aggregate subbase and subgrade soils under these gravel roads are produced with material opportunistically chosen from local sources near the site and, many times, the compositions of these sublayers are far from ideal in terms of proper water drainage with the full effects of this shortcut not being fully understood. The primary objective of this project was to provide a physically-based model for evaluating the drainability of potential subbase and subgrade materials for gravel roads in Iowa. The Richards equation provided the appropriate framework to study the transient unsaturated flow that usually occurs through the subbase and subgrade of a gravel road. From which, we identified that the saturated hydraulic conductivity, Ks, was a key parameter driving the time to drain of subgrade soils found in Iowa, thus being a good proxy variable for accessing roadway drainability. Using Ks, derived from soil texture, we were able to identify potential problem areas in terms of roadway drainage . It was found that there is a threshold for Ks of 15 cm/day that determines if the roadway will drain efficiently, based on the requirement that the time to drain, Td, the surface roadway layer does not exceed a 2-hr limit. Two of the three highest abundant textures (loam and silty clay loam), which cover nearly 60% of the state of Iowa, were found to have average Td values greater than the 2-hr limit. With such a large percentage of the state at risk for the formation of boils due to the soil with relatively low saturated hydraulic conductivity values, it seems pertinent that we propose alternative design and/or maintenance practices to limit the expensive repair work in Iowa. The addition of drain tiles or French mattresses my help address drainage problems. However, before pursuing this recommendation, a comprehensive cost-benefit analysis is needed.

Development of pharmaceutical care services in nursing homes: practice and research in a Swiss canton.

OBJECTIVE: The aim of this study was to assess the implementation process and economic impact of a new pharmaceutical care service provided since 2002 by pharmacists in Swiss nursing homes. SETTING: The setting was 42 nursing homes located in the canton of Fribourg, Switzerland under the responsibility of 22 pharmacists. METHOD: We developed different facilitators, such as a monitoring system, a coaching program, and a research project, to help pharmacists change their practice and to improve implementation of this new service. We evaluated the implementation rate of the service delivered in nursing homes. We assessed the economic impact of the service since its start in 2002 using statistical evaluation (Chow test) with retrospective analysis of the annual drug costs per resident over an 8-year period (1998-2005). MAIN OUTCOME MEASURES: The description of the facilitators and their implications in implementation of the service; the economic impact of the service since its start in 2002. RESULTS: In 2005, after a 4-year implementation period supported by the introduction of facilitators of practice change, all 42 nursing homes (2,214 residents) had implemented the pharmaceutical care service. The annual drug costs per resident decreased by about 16.4% between 2002 and 2005; this change proved to be highly significant. The performance of the pharmacists continuously improved using a specific coaching program including an annual expert comparative report, working groups, interdisciplinary continuing education symposia, and individual feedback. This research project also determined priorities to develop practice guidelines to prevent drug-related problems in nursing homes, especially in relation to the use of psychotropic drugs. CONCLUSION: The pharmaceutical care service was fully and successfully implemented in Fribourg's nursing homes within a period of 4 years. These findings highlight the importance of facilitators designed to assist pharmacists in the implementation of practice changes. The economic impact was confirmed on a large scale, and priorities for clinical and pharmacoeconomic research were identified in order to continue to improve the quality of integrated care for the elderly.

Moving to the development of an HIA methodology : the effects of air pollution in Ticino, Switzerland

This chapter describes the profile of the HIA, provides insight into the process and gives an example of how political decisions may be made on behalf of a concerned population through an HIA approach. [Introduction p. 284]

Infirmier en psychiatrie de liaison : développement de la supervision en milieu somatique [Liaison psychiatry nurse: The development of supervision in somatic medicine].

BACKGROUND: Over the years, somatic care has become increasingly specialized. Furthermore, a rising number of patients requiring somatic care also present with a psychiatric comorbidity. As a consequence, the time and resources needed to care for these patients can interfere with the course of somatic treatment and influence the patient-caregiver relationship. In the light of these observations, the Liaison Psychiatry Unit at the University Hospital in Lausanne (CHUV) has educated its nursing staff in order to strengthen its action within the general care hospital. What has been developed is a reflexive approach through supervision of somatic staff, in order to improve the efficiency of liaison psychiatry interventions with the caregivers in charge of patients. The kind of supervision we have developed is the result of a real partnership with somatic staff. Besides, in order to better understand the complexity of interactions between the two systems involved, the patient's and the caregivers', we use several theoretical references in an integrative manner. PSYCHOANALYTICAL REFERENCE: The psychoanalytical model allows us to better understand the dynamics between the supervisor and the supervised group in order to contain and give meaning to the affects arising in the supervision space. "Containing function" and "transitional phenomena" refer to the experience in which emotions can find a space where they can be taken in and processed in a secure and supportive manner. These concepts, along with that of the "psychic envelope", were initially developed to explain the psychological development of the baby in its early interactions with its mother or its surrogate. In the field of supervision, they allow us to be aware of these complex phenomena and the diverse qualities to which a supervisor needs to resort, such as attention, support and incentive, in order to offer a secure environment. SYSTEMIC REFERENCE: A new perspective of the patient's complexity is revealed by the group's dynamics. The supervisor's attention is mainly focused on the work of affects. However, these are often buried under a defensive shell, serving as a temporary protection, which prevents the caregiver from recognizing his or her own emotions, thereby enhancing the difficulties in the relationship with the patient. Whenever the work of putting emotions into words fail, we use "sculpting", a technique derived from the systemic model. Through the use of this type of analogical language, affects can emerge without constraint or feelings of danger. Through "playing" in that "transitional space", new exchanges appear between group members and allow new behaviors to be conceived. In practice, we ask the supervisee who is presenting a complex situation, to design a spatial representation of his or her understanding of the situation, through the display of characters significant to the situation: the patient, somatic staff members, relatives of the patient, etc. In silence, the supervisee shapes the characters into postures and arranges them in the room. Each sculpted character is identified, named, and positioned, with his or her gaze being set in a specific direction. Finally the sculptor shapes him or herself in his or her own role. When the sculpture is complete and after a few moments of fixation, we ask participants to express themselves about their experience. By means of this physical representation, participants to the sculpture discover perceptions and feelings that were unknown up to then. Hence from this analogical representation a reflection and hypotheses of understanding can arise and be developed within the group. CONCLUSION: Through the use of the concepts of "containing function" and "transitional space" we position ourselves in the scope of the encounter and the dialog. Through the use of the systemic technique of "sculpting" we promote the process of understanding, rather than that of explaining, which would place us in the position of experts. The experience of these encounters has shown us that what we need to focus on is indeed what happens in this transitional space in terms of dynamics and process. The encounter and the sharing of competencies both allow a new understanding of the situation at hand, which has, of course, to be verified in the reality of the patient-caregiver relationship. It is often a source of adjustment for interpersonal skills to recover its containing function in order to enable caregiver to better respond to the patient's needs.

Microtubule-associated protein 1a is involved in the early development of the rat spinal cord.

The expression of microtubule-associated protein 1a (MAP1a) in the developing rat spinal cord was studied using the monoclonal antibody BW6. Immunoblots of microtubule preparations revealed the presence of MAP1a in spinal cord tissue of rats aged embryonal day 16 and postnatal day 0. The spinal cord matrix layer, between embryonal days 12-17, displayed a pattern of MAP1a-positive processes, horizontally oriented in between the membrane limitans interna and externa. The mantle layer stained intensely for MAP1a between embryonal day 12 and postnatal day 2. MAP1a was found in neuronal cell bodies, axons and dendrites, located mainly in the ventral and intermediate mantle layer. In the marginal layer, MAP1a-positive axons could be observed between embryonal days 14-18. During further development, the intensity of the MAP1a staining in the spinal columns gradually decreased. These expression patterns indicate an involvement of MAP1a in the proliferation and differentiation of neuroblasts, and the maturation of the long spinal fiber systems, i.e. early events in spinal cord development

Neuronal death in the development of the vertebrate central nervous system

Neuronal death occurs naturally in the development of the vertebrate central nervous system, deleting large numbers of neurons at the time when afferent and efferent connections are being formed. It is these that regulate it, by means of anterograde and retrograde survival signals that depend on trophic molecules and electrical activity. Possible roles include the regulation of neuronal numbers (numerical matching) and the elimination of axonal targeting errors.

Promoting the development of secure mobile agent applications

Peer-reviewed

Development of a cross-European virtual sample repository and HIV resistance database

BACKGROUND: Several European HIV observational data bases have, over the last decade, accumulated a substantial number of resistance test results and developed large sample repositories, There is a need to link these efforts together, We here describe the development of such a novel tool that allows to bind these data bases together in a distributed fashion for which the control and data remains with the cohorts rather than classic data mergers.METHODS: As proof-of-concept we entered two basic queries into the tool: available resistance tests and available samples. We asked for patients still alive after 1998-01-01, and between 180 and 195 cm of height, and how many samples or resistance tests there would be available for these patients, The queries were uploaded with the tool to a central web server from which each participating cohort downloaded the queries with the tool and ran them against their database, The numbers gathered were then submitted back to the server and we could accumulate the number of available samples and resistance tests.RESULTS: We obtained the following results from the cohorts on available samples/resistance test: EuResist: not availableI11,194; EuroSIDA: 20,71611,992; ICONA: 3,751/500; Rega: 302/302; SHCS: 53,78311,485, In total, 78,552 samples and 15,473 resistance tests were available amongst these five cohorts. Once these data items have been identified, it is trivial to generate lists of relevant samples that would be usefuI for ultra deep sequencing in addition to the already available resistance tests, Saon the tool will include small analysis packages that allow each cohort to pull a report on their cohort profile and also survey emerging resistance trends in their own cohort,CONCLUSIONS: We plan on providing this tool to all cohorts within the Collaborative HIV and Anti-HIV Drug Resistance Network (CHAIN) and will provide the tool free of charge to others for any non-commercial use, The potential of this tool is to ease collaborations, that is, in projects requiring data to speed up identification of novel resistance mutations by increasing the number of observations across multiple cohorts instead of awaiting single cohorts or studies to reach the critical number needed to address such issues.

Identification of Research Portfolio for the Development of Filtration Equipment

This piece of work which is Identification of Research Portfolio for Development of Filtration Equipment aims at presenting a novel approach to identify promising research topics in the field of design and development of filtration equipment and processes. The projected approach consists of identifying technological problems often encountered in filtration processes. The sources of information for the problem retrieval were patent documents and scientific papers that discussed filtration equipments and processes. The problem identification method adopted in this work focussed on the semantic nature of a sentence in order to generate series of subject-action-object structures. This was achieved with software called Knowledgist. List of problems often encountered in filtration processes that have been mentioned in patent documents and scientific papers were generated. These problems were carefully studied and categorized. Suggestions were made on the various classes of these problems that need further investigation in order to propose a research portfolio. The uses and importance of other methods of information retrieval were also highlighted in this work.

Development of Order-Delivery Process in Purchasing

Diplomityön tavoitteena oli kehittää Fazer Suklaan oston tilaus-toimitusprosesseja, jotta raaka-aineet ja pakkausmateriaalit pystytään hoitamaan mahdollisimman tehokkaasti. Ensin selvitettiin kirjallisuuden avulla tilaus-toimitusprosessin päävaiheet ja niihin vaikuttavat tekijät. Empiirisessä osassa lähdettiin liikkeelle käymällä läpi Fazer Suklaan oston nykytilanne, joka tehtiin ostajille suunnatun aikaselvityksen, haastatteluiden ja nykyisten tilaus-toimitusprosessien kuvaamisen avulla. Tavoitetilanteen rakentaminen aloitettiin ostettavien materiaalien ja toimittajien luokittelemisella. Tämän perusteella nämä materiaalit voitiin jakaa kolmen eri tilaus toimitusprosessin alle. Automaattisessa tilaus-toimitusprosessissa eri vaiheet automatisoidaan yhdessäavain toimittajien kanssa. Puoliautomaattinen prosessi perustuu systeemiin, jossa toimittaja näkee internetin kautta Fazerin tuotantosuunnitelman ja tekee tämän perusteella materiaalien täydennykset. Yksinkertaisessa prosessissa ostoarvoltaan alhaiset materiaalit hoidetaan mahdollisimman lähellä käyttöpistettä ja prosessin vaiheet tehdään mandollisimman pienellä työmäärällä. Tavoiteprosessien implementoinnilla todettiin suurimmiksi eduiksi prosessivaiheiden vähentyminen ja manuaalisen työn automatisoituminen. Tätä kautta saatiin prosessin eri vaiheiden työmäärää vähennettyä, sekä alennettua varastotasoja ja näin tilaus toimitusprosessin kokonaiskustannuksia pystyttiin pienentämään.

Development of fluid conduits in the auriferous shear zones of the Hutti Gold Mine, India: evidence for spatially and temporally heterogeneous fluid flow

The gold mineralization of the Hutti Mine is hosted by nine parallel, N - S trending, steeply dipping, 2 - 10 m wide shear zones, that transect Archaean amphibolites. The shear zones were formed after peak metamorphism during retrograde ductile D, shearing in the lower amphibolite facies. They were reactivated in the lower to mid greenschist facies by brittle-ductile D-3 shearing and intense quartz veining. The development of a S-2-S-3 crenulation cleavage facilitates the discrimination between the two deformation events and contemporaneous alteration and gold mineralization. Ductile D, shearing is associated with a pervasively developed distal chlorite - sed cite alteration assemblage in the outer parts of the shear zones and the proximal biotite-plagioclase alteration in the center of the shear zones. D3 is characterized by development of the inner chlorite-K-feldspar alteration, which forms a centimeter-scale alteration halo surrounding the laminated quartz veins and replaces earlier biotite along S-3. The average size of the laminated vein systems is 30-50 m along strike as well as down-dip and 2-6 m in width. Mass balance calculations suggest strong metasomatic changes for the proximal biotite-plagioclase alteration yielding mass and volume increase of ca. 16% and 12%, respectively. The calculated mass and volume changes of the distal chlorite-sericite alteration (ca. 11%, ca. 8%) are lower. The decrease in 6180 values of the whole rock from around 7.5 parts per thousand for the host rocks to 6-7 parts per thousand for the distal chlorite-sericite and the proximal biotite-plagioclase alteration and around 5 parts per thousand for the inner chlorite-K-feldspar alteration suggests hydrothermal alteration during two-stage deformation and fluid flow. The ductile D-2 deformation in the lower amphibolite facies has provided grain scale porosities by microfracturing. The pervasive, steady-state fluid flow resulted in a disseminated style of gold-sulfide mineralization and a penetrative alteration of the host rocks. Alternating ductile and brittle D3 deformation during lower to mid greenschist facies conditions followed the fault-valve process. Ductile creep in the shear zones resulted in a low permeability environment leading to fluid pressure build-up. Strongly episodic fluid advection and mass transfer was controlled by repeated seismic fracturing during the formation of laminated quartz(-gold) veins. The limitation of quartz veins to the extent of earlier shear zones indicate the importance of preexisting anisotropies for fault-valve action and economic gold mineralization. (C) 2003 Elsevier B.V. All rights reserved.

Development of a 3D very high-resolution seismic reflection system for lacustrine settings - a case study over a thrust fault zone in Lake Geneva

Un système efficace de sismique tridimensionnelle (3-D) haute-résolution adapté à des cibles lacustres de petite échelle a été développé. Dans le Lac Léman, près de la ville de Lausanne, en Suisse, des investigations récentes en deux dimension (2-D) ont mis en évidence une zone de faille complexe qui a été choisie pour tester notre système. Les structures observées incluent une couche mince (<40 m) de sédiments quaternaires sub-horizontaux, discordants sur des couches tertiaires de molasse pentées vers le sud-est. On observe aussi la zone de faille de « La Paudèze » qui sépare les unités de la Molasse du Plateau de la Molasse Subalpine. Deux campagnes 3-D complètes, d?environ d?un kilomètre carré, ont été réalisées sur ce site de test. La campagne pilote (campagne I), effectuée en 1999 pendant 8 jours, a couvert 80 profils en utilisant une seule flûte. Pendant la campagne II (9 jours en 2001), le nouveau système trois-flûtes, bien paramétrés pour notre objectif, a permis l?acquisition de données de très haute qualité sur 180 lignes CMP. Les améliorations principales incluent un système de navigation et de déclenchement de tirs grâce à un nouveau logiciel. Celui-ci comprend un contrôle qualité de la navigation du bateau en temps réel utilisant un GPS différentiel (dGPS) à bord et une station de référence près du bord du lac. De cette façon, les tirs peuvent être déclenchés tous les 5 mètres avec une erreur maximale non-cumulative de 25 centimètres. Tandis que pour la campagne I la position des récepteurs de la flûte 48-traces a dû être déduite à partir des positions du bateau, pour la campagne II elle ont pu être calculées précisément (erreur <20 cm) grâce aux trois antennes dGPS supplémentaires placées sur des flotteurs attachés à l?extrémité de chaque flûte 24-traces. Il est maintenant possible de déterminer la dérive éventuelle de l?extrémité des flûtes (75 m) causée par des courants latéraux ou de petites variations de trajet du bateau. De plus, la construction de deux bras télescopiques maintenant les trois flûtes à une distance de 7.5 m les uns des autres, qui est la même distance que celle entre les lignes naviguées de la campagne II. En combinaison avec un espacement de récepteurs de 2.5 m, la dimension de chaque «bin» de données 3-D de la campagne II est de 1.25 m en ligne et 3.75 m latéralement. L?espacement plus grand en direction « in-line » par rapport à la direction «cross-line» est justifié par l?orientation structurale de la zone de faille perpendiculaire à la direction «in-line». L?incertitude sur la navigation et le positionnement pendant la campagne I et le «binning» imprécis qui en résulte, se retrouve dans les données sous forme d?une certaine discontinuité des réflecteurs. L?utilisation d?un canon à air à doublechambre (qui permet d?atténuer l?effet bulle) a pu réduire l?aliasing observé dans les sections migrées en 3-D. Celui-ci était dû à la combinaison du contenu relativement haute fréquence (<2000 Hz) du canon à eau (utilisé à 140 bars et à 0.3 m de profondeur) et d?un pas d?échantillonnage latéral insuffisant. Le Mini G.I 15/15 a été utilisé à 80 bars et à 1 m de profondeur, est mieux adapté à la complexité de la cible, une zone faillée ayant des réflecteurs pentés jusqu?à 30°. Bien que ses fréquences ne dépassent pas les 650 Hz, cette source combine une pénétration du signal non-aliasé jusqu?à 300 m dans le sol (par rapport au 145 m pour le canon à eau) pour une résolution verticale maximale de 1.1 m. Tandis que la campagne I a été acquise par groupes de plusieurs lignes de directions alternées, l?optimisation du temps d?acquisition du nouveau système à trois flûtes permet l?acquisition en géométrie parallèle, ce qui est préférable lorsqu?on utilise une configuration asymétrique (une source et un dispositif de récepteurs). Si on ne procède pas ainsi, les stacks sont différents selon la direction. Toutefois, la configuration de flûtes, plus courtes que pour la compagne I, a réduit la couverture nominale, la ramenant de 12 à 6. Une séquence classique de traitement 3-D a été adaptée à l?échantillonnage à haute fréquence et elle a été complétée par deux programmes qui transforment le format non-conventionnel de nos données de navigation en un format standard de l?industrie. Dans l?ordre, le traitement comprend l?incorporation de la géométrie, suivi de l?édition des traces, de l?harmonisation des «bins» (pour compenser l?inhomogénéité de la couverture due à la dérive du bateau et de la flûte), de la correction de la divergence sphérique, du filtrage passe-bande, de l?analyse de vitesse, de la correction DMO en 3-D, du stack et enfin de la migration 3-D en temps. D?analyses de vitesse détaillées ont été effectuées sur les données de couverture 12, une ligne sur deux et tous les 50 CMP, soit un nombre total de 600 spectres de semblance. Selon cette analyse, les vitesses d?intervalles varient de 1450-1650 m/s dans les sédiments non-consolidés et de 1650-3000 m/s dans les sédiments consolidés. Le fait que l?on puisse interpréter plusieurs horizons et surfaces de faille dans le cube, montre le potentiel de cette technique pour une interprétation tectonique et géologique à petite échelle en trois dimensions. On distingue cinq faciès sismiques principaux et leurs géométries 3-D détaillées sur des sections verticales et horizontales: les sédiments lacustres (Holocène), les sédiments glacio-lacustres (Pléistocène), la Molasse du Plateau, la Molasse Subalpine de la zone de faille (chevauchement) et la Molasse Subalpine au sud de cette zone. Les couches de la Molasse du Plateau et de la Molasse Subalpine ont respectivement un pendage de ~8° et ~20°. La zone de faille comprend de nombreuses structures très déformées de pendage d?environ 30°. Des tests préliminaires avec un algorithme de migration 3-D en profondeur avant sommation et à amplitudes préservées démontrent que la qualité excellente des données de la campagne II permet l?application de telles techniques à des campagnes haute-résolution. La méthode de sismique marine 3-D était utilisée jusqu?à présent quasi-exclusivement par l?industrie pétrolière. Son adaptation à une échelle plus petite géographiquement mais aussi financièrement a ouvert la voie d?appliquer cette technique à des objectifs d?environnement et du génie civil.<br/><br/>An efficient high-resolution three-dimensional (3-D) seismic reflection system for small-scale targets in lacustrine settings was developed. In Lake Geneva, near the city of Lausanne, Switzerland, past high-resolution two-dimensional (2-D) investigations revealed a complex fault zone (the Paudèze thrust zone), which was subsequently chosen for testing our system. Observed structures include a thin (<40 m) layer of subhorizontal Quaternary sediments that unconformably overlie southeast-dipping Tertiary Molasse beds and the Paudèze thrust zone, which separates Plateau and Subalpine Molasse units. Two complete 3-D surveys have been conducted over this same test site, covering an area of about 1 km2. In 1999, a pilot survey (Survey I), comprising 80 profiles, was carried out in 8 days with a single-streamer configuration. In 2001, a second survey (Survey II) used a newly developed three-streamer system with optimized design parameters, which provided an exceptionally high-quality data set of 180 common midpoint (CMP) lines in 9 days. The main improvements include a navigation and shot-triggering system with in-house navigation software that automatically fires the gun in combination with real-time control on navigation quality using differential GPS (dGPS) onboard and a reference base near the lake shore. Shots were triggered at 5-m intervals with a maximum non-cumulative error of 25 cm. Whereas the single 48-channel streamer system of Survey I requires extrapolation of receiver positions from the boat position, for Survey II they could be accurately calculated (error <20 cm) with the aid of three additional dGPS antennas mounted on rafts attached to the end of each of the 24- channel streamers. Towed at a distance of 75 m behind the vessel, they allow the determination of feathering due to cross-line currents or small course variations. Furthermore, two retractable booms hold the three streamers at a distance of 7.5 m from each other, which is the same distance as the sail line interval for Survey I. With a receiver spacing of 2.5 m, the bin dimension of the 3-D data of Survey II is 1.25 m in in-line direction and 3.75 m in cross-line direction. The greater cross-line versus in-line spacing is justified by the known structural trend of the fault zone perpendicular to the in-line direction. The data from Survey I showed some reflection discontinuity as a result of insufficiently accurate navigation and positioning and subsequent binning errors. Observed aliasing in the 3-D migration was due to insufficient lateral sampling combined with the relatively high frequency (<2000 Hz) content of the water gun source (operated at 140 bars and 0.3 m depth). These results motivated the use of a double-chamber bubble-canceling air gun for Survey II. A 15 / 15 Mini G.I air gun operated at 80 bars and 1 m depth, proved to be better adapted for imaging the complexly faulted target area, which has reflectors dipping up to 30°. Although its frequencies do not exceed 650 Hz, this air gun combines a penetration of non-aliased signal to depths of 300 m below the water bottom (versus 145 m for the water gun) with a maximum vertical resolution of 1.1 m. While Survey I was shot in patches of alternating directions, the optimized surveying time of the new threestreamer system allowed acquisition in parallel geometry, which is preferable when using an asymmetric configuration (single source and receiver array). Otherwise, resulting stacks are different for the opposite directions. However, the shorter streamer configuration of Survey II reduced the nominal fold from 12 to 6. A 3-D conventional processing flow was adapted to the high sampling rates and was complemented by two computer programs that format the unconventional navigation data to industry standards. Processing included trace editing, geometry assignment, bin harmonization (to compensate for uneven fold due to boat/streamer drift), spherical divergence correction, bandpass filtering, velocity analysis, 3-D DMO correction, stack and 3-D time migration. A detailed semblance velocity analysis was performed on the 12-fold data set for every second in-line and every 50th CMP, i.e. on a total of 600 spectra. According to this velocity analysis, interval velocities range from 1450-1650 m/s for the unconsolidated sediments and from 1650-3000 m/s for the consolidated sediments. Delineation of several horizons and fault surfaces reveal the potential for small-scale geologic and tectonic interpretation in three dimensions. Five major seismic facies and their detailed 3-D geometries can be distinguished in vertical and horizontal sections: lacustrine sediments (Holocene) , glaciolacustrine sediments (Pleistocene), Plateau Molasse, Subalpine Molasse and its thrust fault zone. Dips of beds within Plateau and Subalpine Molasse are ~8° and ~20°, respectively. Within the fault zone, many highly deformed structures with dips around 30° are visible. Preliminary tests with 3-D preserved-amplitude prestack depth migration demonstrate that the excellent data quality of Survey II allows application of such sophisticated techniques even to high-resolution seismic surveys. In general, the adaptation of the 3-D marine seismic reflection method, which to date has almost exclusively been used by the oil exploration industry, to a smaller geographical as well as financial scale has helped pave the way for applying this technique to environmental and engineering purposes.<br/><br/>La sismique réflexion est une méthode d?investigation du sous-sol avec un très grand pouvoir de résolution. Elle consiste à envoyer des vibrations dans le sol et à recueillir les ondes qui se réfléchissent sur les discontinuités géologiques à différentes profondeurs et remontent ensuite à la surface où elles sont enregistrées. Les signaux ainsi recueillis donnent non seulement des informations sur la nature des couches en présence et leur géométrie, mais ils permettent aussi de faire une interprétation géologique du sous-sol. Par exemple, dans le cas de roches sédimentaires, les profils de sismique réflexion permettent de déterminer leur mode de dépôt, leurs éventuelles déformations ou cassures et donc leur histoire tectonique. La sismique réflexion est la méthode principale de l?exploration pétrolière. Pendant longtemps on a réalisé des profils de sismique réflexion le long de profils qui fournissent une image du sous-sol en deux dimensions. Les images ainsi obtenues ne sont que partiellement exactes, puisqu?elles ne tiennent pas compte de l?aspect tridimensionnel des structures géologiques. Depuis quelques dizaines d?années, la sismique en trois dimensions (3-D) a apporté un souffle nouveau à l?étude du sous-sol. Si elle est aujourd?hui parfaitement maîtrisée pour l?imagerie des grandes structures géologiques tant dans le domaine terrestre que le domaine océanique, son adaptation à l?échelle lacustre ou fluviale n?a encore fait l?objet que de rares études. Ce travail de thèse a consisté à développer un système d?acquisition sismique similaire à celui utilisé pour la prospection pétrolière en mer, mais adapté aux lacs. Il est donc de dimension moindre, de mise en oeuvre plus légère et surtout d?une résolution des images finales beaucoup plus élevée. Alors que l?industrie pétrolière se limite souvent à une résolution de l?ordre de la dizaine de mètres, l?instrument qui a été mis au point dans le cadre de ce travail permet de voir des détails de l?ordre du mètre. Le nouveau système repose sur la possibilité d?enregistrer simultanément les réflexions sismiques sur trois câbles sismiques (ou flûtes) de 24 traces chacun. Pour obtenir des données 3-D, il est essentiel de positionner les instruments sur l?eau (source et récepteurs des ondes sismiques) avec une grande précision. Un logiciel a été spécialement développé pour le contrôle de la navigation et le déclenchement des tirs de la source sismique en utilisant des récepteurs GPS différentiel (dGPS) sur le bateau et à l?extrémité de chaque flûte. Ceci permet de positionner les instruments avec une précision de l?ordre de 20 cm. Pour tester notre système, nous avons choisi une zone sur le Lac Léman, près de la ville de Lausanne, où passe la faille de « La Paudèze » qui sépare les unités de la Molasse du Plateau et de la Molasse Subalpine. Deux campagnes de mesures de sismique 3-D y ont été réalisées sur une zone d?environ 1 km2. Les enregistrements sismiques ont ensuite été traités pour les transformer en images interprétables. Nous avons appliqué une séquence de traitement 3-D spécialement adaptée à nos données, notamment en ce qui concerne le positionnement. Après traitement, les données font apparaître différents faciès sismiques principaux correspondant notamment aux sédiments lacustres (Holocène), aux sédiments glacio-lacustres (Pléistocène), à la Molasse du Plateau, à la Molasse Subalpine de la zone de faille et la Molasse Subalpine au sud de cette zone. La géométrie 3-D détaillée des failles est visible sur les sections sismiques verticales et horizontales. L?excellente qualité des données et l?interprétation de plusieurs horizons et surfaces de faille montrent le potentiel de cette technique pour les investigations à petite échelle en trois dimensions ce qui ouvre des voies à son application dans les domaines de l?environnement et du génie civil.

Development of advanced silicon radiation detectors for harsh radiation environment

This thesis describes the development of advanced silicon radiation detectors and their characterization by simulations, used in the work for searching elementary particles in the European Organization for Nuclear Research, CERN. Silicon particle detectors will face extremely harsh radiation in the proposed upgrade of the Large Hadron Collider, the future high-energy physics experiment Super-LHC. The increase in the maximal fluence and the beam luminosity up to 1016 neq / cm2 and 1035 cm-2s-1 will require detectors with a dramatic improvement in radiation hardness, when such a fluence will be far beyond the operational limits of the present silicon detectors. The main goals of detector development concentrate on minimizing the radiation degradation. This study contributes mainly to the device engineering technology for developing more radiation hard particle detectors with better characteristics. Also the defect engineering technology is discussed. In the nearest region of the beam in Super-LHC, the only detector choice is 3D detectors, or alternatively replacing other types of detectors every two years. The interest in the 3D silicon detectors is continuously growing because of their many advantages as compared to conventional planar detectors: the devices can be fully depleted at low bias voltages, the speed of the charge collection is high, and the collection distances are about one order of magnitude less than those of planar technology strip and pixel detectors with electrodes limited to the detector surface. Also the 3D detectors exhibit high radiation tolerance, and thus the ability of the silicon detectors to operate after irradiation is increased. Two parameters, full depletion voltage and electric field distribution, is discussed in more detail in this study. The full depletion of the detector is important because the only depleted area in the detector is active for the particle tracking. Similarly, the high electric field in the detector makes the detector volume sensitive, while low-field areas are non-sensitive to particles. This study shows the simulation results of full depletion voltage and the electric field distribution for the various types of 3D detectors. First, the 3D detector with the n-type substrate and partial-penetrating p-type electrodes are researched. A detector of this type has a low electric field on the pixel side and it suffers from type inversion. Next, the substrate is changed to p-type and the detectors having electrodes with one doping type and the dual doping type are examined. The electric field profile in a dual-column 3D Si detector is more uniform than that in the single-type column 3D detector. The dual-column detectors are the best in radiation hardness because of their low depletion voltages and short drift distances.

The Development of an Internal Testing Process for a Bluetooth Product

BlueGiga Technologies on uusi Bluetooth -teknologiaa soveltava pk-yritys. Yrityksen tuotekehitysprosessia täydentämään tarvittiin testausprosessi. Testausprosessin luominen oli haastavaa, koska Bluetooth -teknologia on uutta ja yritys on vielä nuori. Lisäksi se integroi kovo- ja ohjelmistokomponentteja tuotteissaan. Testaus aloitettiin evaluoimalla standardinmukaista tapaa dokumentoida testit. Tämän jälkeen tutkittiin BlueGigan ohjelmistokehitysprosessin suhdetta olemassa oleviin ohjelmistokehitysprosesseihin. Samanaikaisesti perehdyttiin Bluetooth -kvalifikaation testaukselle asettamiin vaatimuksiin. Tämän seurauksena TTCN:ää kokeiltiin helppolukuisen testitapauksen määrittelyssä. Käyttötapauksiin perustuvan testauksen sopivuutta Wireless Remote Access Platform:in (WRAP) testaamiseen arvioitiin kokeilemalla sitä Man-to-Machine -käyttötapauksen testaamisessa. Yllämainittujen tehtävien aikana kerätyn tiedon ja hankittujen kokemusten pohjalta laadittiin testausprosessi, joka kattaa yksikkö-, integraatio- ja järjestelmätason testauksen. Painopiste on järjestelmätason testauksessa. Prosessi määrittelee myös vastuuhenkilön tai -henkilöt eri testaustasoille.

Aspirin and statin use and the subsequent development of depression in men and women: Results from a longitudinal population-based study.

OBJECTIVE: Low-grade chronic inflammation is one potential mechanism underlying the well-established association between major depressive disorder (MDD) and increased cardiovascular morbidity. Both aspirin and statins have anti-inflammatory properties, which may contribute to their preventive effect on cardiovascular diseases. Previous studies on the potentially preventive effect of these drugs on depression have provided inconsistent results. The aim of the present paper was to assess the prospective association between regular aspirin or statin use and the incidence of MDD. METHOD: This prospective cohort study included 1631 subjects (43.6% women, mean age 51.7 years), randomly selected from the general population of an urban area. Subjects underwent a thorough physical evaluation as well as semi-structured interviews investigating DSM-IV mental disorders at baseline and follow-up (mean duration 5.2 years). Analyses were adjusted for a wide array of potential confounders. RESULTS: Our main finding was that regular aspirin or statin use at baseline did not reduce the incidence of MDD during follow-up, regardless of sex or age (hazard ratios, aspirin: 1.19; 95%CI, 0.68-2.08; and statins: 1.25; 95%CI, 0.73-2.14; respectively). LIMITATIONS: Our study is not a randomized clinical trial and could not adjust for all potential confounding factors, information on aspirin or statin use was collected only for the 6 months prior to the evaluations, and the sample was restricted to subjects between 35 and 66 years of age. CONCLUSION: Our data do not support a large scale preventive treatment of depression using aspirin or statins in subjects aged from 35 to 66 years from the community.