Asset management of wastewater networks

Asset Management (AM) is a set of procedures operable at the strategic-tacticaloperational level, for the management of the physical asset’s performance, associated risks and costs within its whole life-cycle. AM combines the engineering, managerial and informatics points of view. In addition to internal drivers, AM is driven by the demands of customers (social pull) and regulators (environmental mandates and economic considerations). AM can follow either a top-down or a bottom-up approach. Considering rehabilitation planning at the bottom-up level, the main issue would be to rehabilitate the right pipe at the right time with the right technique. Finding the right pipe may be possible and practicable, but determining the timeliness of the rehabilitation and the choice of the techniques adopted to rehabilitate is a bit abstruse. It is a truism that rehabilitating an asset too early is unwise, just as doing it late may have entailed extra expenses en route, in addition to the cost of the exercise of rehabilitation per se. One is confronted with a typical ‘Hamlet-isque dilemma’ – ‘to repair or not to repair’; or put in another way, ‘to replace or not to replace’. The decision in this case is governed by three factors, not necessarily interrelated – quality of customer service, costs and budget in the life cycle of the asset in question. The goal of replacement planning is to find the juncture in the asset’s life cycle where the cost of replacement is balanced by the rising maintenance costs and the declining level of service. System maintenance aims at improving performance and maintaining the asset in good working condition for as long as possible. Effective planning is used to target maintenance activities to meet these goals and minimize costly exigencies. The main objective of this dissertation is to develop a process-model for asset replacement planning. The aim of the model is to determine the optimal pipe replacement year by comparing, temporally, the annual operating and maintenance costs of the existing asset and the annuity of the investment in a new equivalent pipe, at the best market price. It is proposed that risk cost provide an appropriate framework to decide the balance between investment for replacing or operational expenditures for maintaining an asset. The model describes a practical approach to estimate when an asset should be replaced. A comprehensive list of criteria to be considered is outlined, the main criteria being a visà- vis between maintenance and replacement expenditures. The costs to maintain the assets should be described by a cost function related to the asset type, the risks to the safety of people and property owing to declining condition of asset, and the predicted frequency of failures. The cost functions reflect the condition of the existing asset at the time the decision to maintain or replace is taken: age, level of deterioration, risk of failure. The process model is applied in the wastewater network of Oslo, the capital city of Norway, and uses available real-world information to forecast life-cycle costs of maintenance and rehabilitation strategies and support infrastructure management decisions. The case study provides an insight into the various definitions of ‘asset lifetime’ – service life, economic life and physical life. The results recommend that one common value for lifetime should not be applied to the all the pipelines in the stock for investment planning in the long-term period; rather it would be wiser to define different values for different cohorts of pipelines to reduce the uncertainties associated with generalisations for simplification. It is envisaged that more criteria the municipality is able to include, to estimate maintenance costs for the existing assets, the more precise will the estimation of the expected service life be. The ability to include social costs enables to compute the asset life, not only based on its physical characterisation, but also on the sensitivity of network areas to social impact of failures. The type of economic analysis is very sensitive to model parameters that are difficult to determine accurately. The main value of this approach is the effort to demonstrate that it is possible to include, in decision-making, factors as the cost of the risk associated with a decline in level of performance, the level of this deterioration and the asset’s depreciation rate, without looking at age as the sole criterion for making decisions regarding replacements.

An evolutive approach for smile recognition in video sequences

Facial expression recognition is one of the most challenging research areas in the image recognition ¯eld and has been actively studied since the 70's. For instance, smile recognition has been studied due to the fact that it is considered an important facial expression in human communication, it is therefore likely useful for human–machine interaction. Moreover, if a smile can be detected and also its intensity estimated, it will raise the possibility of new applications in the future

Aspetti di sostenibilità in agricoltura a diverse scale spaziali e temporali. Valutazioni ambientali, economiche ed energetiche.

La Tesi analizza le relazioni tra i processi di sviluppo agricolo e l’uso delle risorse naturali, in particolare di quelle energetiche, a livello internazionale (paesi in via di sviluppo e sviluppati), nazionale (Italia), regionale (Emilia Romagna) e aziendale, con lo scopo di valutare l’eco-efficienza dei processi di sviluppo agricolo, la sua evoluzione nel tempo e le principali dinamiche in relazione anche ai problemi di dipendenza dalle risorse fossili, della sicurezza alimentare, della sostituzione tra superfici agricole dedicate all’alimentazione umana ed animale. Per i due casi studio a livello macroeconomico è stata adottata la metodologia denominata “SUMMA” SUstainability Multi-method, multi-scale Assessment (Ulgiati et al., 2006), che integra una serie di categorie d’impatto dell’analisi del ciclo di vita, LCA, valutazioni costi-benefici e la prospettiva di analisi globale della contabilità emergetica. L’analisi su larga scala è stata ulteriormente arricchita da un caso studio sulla scala locale, di una fattoria produttrice di latte e di energia elettrica rinnovabile (fotovoltaico e biogas). Lo studio condotto mediante LCA e valutazione contingente ha valutato gli effetti ambientali, economici e sociali di scenari di riduzione della dipendenza dalle fonti fossili. I casi studio a livello macroeconomico dimostrano che, nonostante le politiche di supporto all’aumento di efficienza e a forme di produzione “verdi”, l’agricoltura a livello globale continua ad evolvere con un aumento della sua dipendenza dalle fonti energetiche fossili. I primi effetti delle politiche agricole comunitarie verso una maggiore sostenibilità sembrano tuttavia intravedersi per i Paesi Europei. Nel complesso la energy footprint si mantiene alta poiché la meccanizzazione continua dei processi agricoli deve necessariamente attingere da fonti energetiche sostitutive al lavoro umano. Le terre agricole diminuiscono nei paesi europei analizzati e in Italia aumentando i rischi d’insicurezza alimentare giacché la popolazione nazionale sta invece aumentando.

Social housing: interventions of densification in urban regeneration (1995-2010). Critical analysis of strategies adopted in Milan, London, São Paulo

The prospect of the continuous multiplication of life styles, the obsolescence of the traditional typological diagrams, the usability of spaces on different territorial scales, imposes on contemporary architecture the search for new models of living. Limited densities in urban development have produced the erosion of territory, the increase of the harmful emissions and energy consumption. High density housing cannot refuse the social emergency to ensure high quality and low cost dwellings, to a new people target: students, temporary workers, key workers, foreign, young couples without children, large families and, in general, people who carry out public services. Social housing strategies have become particularly relevant in regenerating high density urban outskirts. The choice of this research topic derives from the desire to deal with the recent accommodation emergency, according to different perspectives, with a view to give a contribution to the current literature, by proposing some tools for a correct design of the social housing, by ensuring good quality, cost-effective, and eco-sustainable solutions, from the concept phase, through management and maintenance, until the end of the building life cycle. The purpose of the thesis is defining a framework of guidelines that become effective instruments to be used in designing the social housing. They should also integrate the existing regulations and are mainly thought for those who work in this sector. They would aim at supporting students who have to cope with this particular residential theme, and also the users themselves. The scientific evidence of either the recent specialized literature or the solutions adopted in some case studies within the selected metropolitan areas of Milan, London and São Paulo, it is possible to identify the principles of this new design approach, in which the connection between typology, morphology and technology pursues the goal of a high living standard.

Identificazione di possibili unita' di stock di Anguilla anguilla mediante analisi microchimica e morfometrica degli otoliti

L’anguilla europea, è una specie eurialina catadroma con un complesso ciclo biologico: l’area di riproduzione, unica, si trova molto distante da quella di distribuzione. La specie necessita di una gestione dello stock a fini conservazionistici. Il problema è europeo: lo stock è unico, distribuito in Europa e nell’Africa settentrionale, si riproduce in Atlantico ed è panmittico. C’è preoccupazione per il declino del reclutamento e delle catture di adulti. Lo scopo del progetto è di individuare possibili unità di stock nella penisola italiana. La ricerca è basata sullo studio degli otoliti mediante analisi morfometrica e microchimica. I contorni degli otoliti sono sottoposti ad analisi ellittica di Fourier per individuare eventuali gruppi. Gli otoliti sono stati levigati per effettuare: letture d’età, indagini microstrutturali al SEM delle fasi larvali, analisi microchimiche LA-ICP-MS del nucleo, studiarne l’origine e valutare l’ambiente di sviluppo. Le indagini morfometriche mostrano evidenti pattern ontogenetici, ma non legati ocorrelati alla località, sesso o anno di nascita. Le indagini microstrutturali hanno evidenziano l’alto contenuto organico nucleare, un pattern comune di crescita ed eventi chiave delle fasi larvali, con una media di 212 anelli giornalieri. La microchimica rivela che le larve si sviluppano in acque salate fino alla metamorfosi, poi migrano verso acque meno salate. Le analisi su campioni nati nello stesso anno, evidenziano due gruppi: individui di rimonta naturale e individui di ripopolamento. I profili nucleo bordo evidenziano la permanenza a salinità intermedie degli adulti. L’attività di ricerca si è dimostrata proficua dal punto di vista tecnico con la messa a punto di protocolli innovativi e con forti ricadute sulla riduzione dei tempi e costi d’analisi. Il debole segnale di possibili unità di stock andrà verificato in futuro mediante analisi più dettagliate discriminando meglio la storia di ogni singolo individuo.

La strategia BIM a supporto del progetto della sicurezza nel cantiere edile: il caso dell'ospedale di primo soccorso a Lampedusa.

Throughout this research, the whole life cycle of a building will be analyzed, with a special focus on the most common issues that affect the construction sector nowadays, such as safety. In fact, the goal is to enhance the management of the entire construction process in order to reduce the risk of accidents. The contemporary trend is that of researching new tools capable of reducing, or even eliminating, the most common mistakes that usually lead to safety risks. That is one of the main reasons why new technologies and tools have been introduced in the field. The one we will focus on is the so-called BIM: Building Information Modeling. With the term BIM we refer to wider and more complex analysis tool than a simple 3D modeling software. Through BIM technologies we are able to generate a multi-dimension 3D model which contains all the information about the project. This innovative approach aims at a better understanding and control of the project by taking into consideration the entire life cycle and resulting in a faster and more sustainable way of management. Furthermore, BIM software allows for the sharing of all the information among the different aspects of the project and among the different participants involved thus improving the cooperation and communication. In addition, BIM software utilizes smart tools that simulate and visualize the process in advance, thus preventing issues that might not have been taking into consideration during the design process. This leads to higher chances of avoiding risks, delays and cost increases. Using a hospital case study, we will apply this approach for the completion of a safety plan, with a special focus onto the construction phase.

Mission synthesis of sine-on-random excitations for accelerated vibration qualification testing

In most real-life environments, mechanical or electronic components are subjected to vibrations. Some of these components may have to pass qualification tests to verify that they can withstand the fatigue damage they will encounter during their operational life. In order to conduct a reliable test, the environmental excitations can be taken as a reference to synthesize the test profile: this procedure is referred to as “test tailoring”. Due to cost and feasibility reasons, accelerated qualification tests are usually performed. In this case, the duration of the original excitation which acts on the component for its entire life-cycle, typically hundreds or thousands of hours, is reduced. In particular, the “Mission Synthesis” procedure lets to quantify the induced damage of the environmental vibration through two functions: the Fatigue Damage Spectrum (FDS) quantifies the fatigue damage, while the Maximum Response Spectrum (MRS) quantifies the maximum stress. Then, a new random Power Spectral Density (PSD) can be synthesized, with same amount of induced damage, but a specified duration in order to conduct accelerated tests. In this work, the Mission Synthesis procedure is applied in the case of so-called Sine-on-Random vibrations, i.e. excitations composed of random vibrations superimposed on deterministic contributions, in the form of sine tones typically due to some rotating parts of the system (e.g. helicopters, engine-mounted components, …). In fact, a proper test tailoring should not only preserve the accumulated fatigue damage, but also the “nature” of the excitation (in this case the sinusoidal components superimposed on the random process) in order to obtain reliable results. The classic time-domain approach is taken as a reference for the comparison of different methods for the FDS calculation in presence of Sine-on-Random vibrations. Then, a methodology to compute a Sine-on-Random specification based on a mission FDS is presented.

Design of an indirectly fired gas turbine integrated with an organic rankine cycle unit for combined heat and power production

In the last years, the European countries have paid increasing attention to renewable sources and greenhouse emissions. The Council of the European Union and the European Parliament have established ambitious targets for the next years. In this scenario, biomass plays a prominent role since its life cycle produces a zero net carbon dioxide emission. Additionally, biomass can ensure plant operation continuity thanks to its availability and storage ability. Several conventional systems running on biomass are available at the moment. Most of them are performant either in the large-scale or in the small power range. The absence of an efficient system on the small-middle scale inspired this thesis project. The object is an innovative plant based on a wet indirectly fired gas turbine (WIFGT) integrated with an organic Rankine cycle (ORC) unit for combined heat and power production. The WIFGT is a performant system in the small-middle power range; the ORC cycle is capable of giving value to low-temperature heat sources. Their integration is investigated in this thesis with the aim of carrying out a preliminary design of the components. The targeted plant output is around 200 kW in order not to need a wide cultivation area and to avoid biomass shipping. Existing in-house simulation tools are used: They are adapted to this purpose. Firstly the WIFGT + ORC model is built; Zero-dimensional models of heat exchangers, compressor, turbines, furnace, dryer and pump are used. Different fluids are selected but toluene and benzene turn out to be the most suitable. In the indirectly fired gas turbine a pressure ratio around 4 leads to the highest efficiency. From the thermodynamic analysis the system shows an electric efficiency of 38%, outdoing other conventional plants in the same power range. The combined plant is designed to recover thermal energy: Water is used as coolant in the condenser. It is heated from 60°C up to 90°C, ensuring the possibility of space heating. Mono-dimensional models are used to design the heat exchange equipment. Different types of heat exchangers are chosen depending on the working temperature. A finned-plate heat exchanger is selected for the WIFGT heat transfer equipment due to the high temperature, oxidizing and corrosive environment. A once-through boiler with finned tubes is chosen to vaporize the organic fluid in the ORC. A plate heat exchanger is chosen for the condenser and recuperator. A quasi-monodimensional model for single-stage axial turbine is implemented to design both the WIFGT and the ORC turbine. The system simulation after the components design shows an electric efficiency around 34% with a decrease by 10% compared to the zero-dimensional analysis. The work exhibits the system potentiality compared to the existing plants from both technical and economic point of view.

Investigating the effect of construction management strategies on project greenhouse gas emissions using interactive simulation

The challenges posed by global climate change are motivating the investigation of strategies that can reduce the life cycle greenhouse gas (GHG) emissions of products and processes. While new construction materials and technologies have received significant attention, there has been limited emphasis on understanding how construction processes can be best managed to reduce GHG emissions. Unexpected disruptive events tend to adversely impact construction costs and delay project completion. They also tend to increase project GHG emissions. The objective of this paper is to investigate ways in which project GHG emissions can be reduced by appropriate management of disruptive events. First, an empirical analysis of construction data from a specific highway construction project is used to illustrate the impact of unexpected schedule delays in increasing project GHG emissions. Next, a simulation based methodology is described to assess the effectiveness of alternative project management strategies in reducing GHG emissions. The contribution of this paper is that it explicitly considers projects emissions, in addition to cost and project duration, in developing project management strategies. Practical application of the method discussed in this paper will help construction firms reduce their project emissions through strategic project management, and without significant investment in new technology. In effect, this paper lays the foundation for best practices in construction management that will optimize project cost and duration, while minimizing GHG emissions.

Comparison of common dredging equipment air emissions

The purpose of this study is to provide a procedure to include emissions to the atmosphere resulting from the combustion of diesel fuel during dredging operations into the decision-making process of dredging equipment selection. The proposed procedure is demonstrated for typical dredging methods and data from the Illinois Waterway as performed by the U.S. Army Corps of Engineers, Rock Island District. The equipment included in this study is a 16-inch cutterhead pipeline dredge and a mechanical bucket dredge used during the 2005 dredging season on the Illinois Waterway. Considerable effort has been put forth to identify and reduce environmental impacts from dredging operations. Though environmental impacts of dredging have been studied no efforts have been applied to the evaluation of air emissions from comparable types of dredging equipment, as in this study. By identifying the type of dredging equipment with the lowest air emissions, when cost, site conditions, and equipment availability are comparable, adverse environmental impacts can be minimized without compromising the dredging project. A total of 48 scenarios were developed by varying the dredged material quantity, transport distance, and production rates. This produced an “envelope” of results applicable to a broad range of site conditions. Total diesel fuel consumed was calculated using standard cost estimating practices as defined in the U.S. Army Corps of Engineers Construction Equipment Ownership and Operating Expense Schedule (USACE, 2005). The diesel fuel usage was estimated for all equipment used to mobilize and/or operate each dredging crew for every scenario. A Limited Life Cycle Assessment (LCA) was used to estimate the air emissions from two comparable dredging operations utilizing SimaPro LCA software. An Environmental Impact Single Score (EISS) was the SimaPro output selected for comparison with the cost per CY of dredging, potential production rates, and transport distances to identify possible decision points. The total dredging time was estimated for each dredging crew and scenario. An average hourly cost for both dredging crews was calculated based on Rock Island District 2005 dredging season records (Graham 2007/08). The results from this study confirm commonly used rules of thumb in the dredging industry by indicating that mechanical bucket dredges are better suited for long transport distances and have lower air emissions and cost per CY for smaller quantities of dredged material. In addition, the results show that a cutterhead pipeline dredge would be preferable for moderate and large volumes of dredged material when no additional booster pumps are required. Finally, the results indicate that production rates can be a significant factor when evaluating the air emissions from comparable dredging equipment.

THE POTENTIAL OF INDUSTRIAL WASTE AND AGRICULTURAL FEEDSTOCK TOWARDS SUSTAINABLE BIOFUELS PRODUCTION: TECHNO-ECONOMIC AND ENVIRONMENTAL IMPACT PERSPECTIVES

This Ph.D. research is comprised of three major components; (i) Characterization study to analyze the composition of defatted corn syrup (DCS) from a dry corn mill facility (ii) Hydrolysis experiments to optimize the production of fermentable sugars and amino acid platform using DCS and (iii) Sustainability analyses. Analyses of DCS included total solids, ash content, total protein, amino acids, inorganic elements, starch, total carbohydrates, lignin, organic acids, glycerol, and presence of functional groups. Total solids content was 37.4% (± 0.4%) by weight, and the mass balance closure was 101%. Total carbohydrates [27% (± 5%) wt.] comprised of starch (5.6%), soluble monomer carbohydrates (12%) and non-starch carbohydrates (10%). Hemicellulose components (structural and non-structural) were; xylan (6%), xylose (1%), mannan (1%), mannose (0.4%), arabinan (1%), arabinose (0.4%), galatactan (3%) and galactose (0.4%). Based on the measured physical and chemical components, bio-chemical conversion route and subsequent fermentation to value added products was identified as promising. DCS has potential to serve as an important fermentation feedstock for bio-based chemicals production. In the sugar hydrolysis experiments, reaction parameters such as acid concentration and retention time were analyzed to determine the optimal conditions to maximize monomer sugar yields while keeping the inhibitors at minimum. Total fermentable sugars produced can reach approximately 86% of theoretical yield when subjected to dilute acid pretreatment (DAP). DAP followed by subsequent enzymatic hydrolysis was most effective for 0 wt% acid hydrolysate samples and least efficient towards 1 and 2 wt% acid hydrolysate samples. The best hydrolysis scheme DCS from an industry's point of view is standalone 60 minutes dilute acid hydrolysis at 2 wt% acid concentration. The combined effect of hydrolysis reaction time, temperature and ratio of enzyme to substrate ratio to develop hydrolysis process that optimizes the production of amino acids in DCS were studied. Four key hydrolysis pathways were investigated for the production of amino acids using DCS. The first hydrolysis pathway is the amino acid analysis using DAP. The second pathway is DAP of DCS followed by protein hydrolysis using proteases [Trypsin, Pronase E (Streptomyces griseus) and Protex 6L]. The third hydrolysis pathway investigated a standalone experiment using proteases (Trypsin, Pronase E, Protex 6L, and Alcalase) on the DCS without any pretreatment. The final pathway investigated the use of Accellerase 1500® and Protex 6L to simultaneously produce fermentable sugars and amino acids over a 24 hour hydrolysis reaction time. The 3 key objectives of the techno-economic analysis component of this PhD research included; (i) Development of a process design for the production of both the sugar and amino acid platforms with DAP using DCS (ii) A preliminary cost analysis to estimate the initial capital cost and operating cost of this facility (iii) A greenhouse gas analysis to understand the environmental impact of this facility. Using Aspen Plus®, a conceptual process design has been constructed. Finally, both Aspen Plus Economic Analyzer® and Simapro® sofware were employed to conduct the cost analysis as well as the carbon footprint emissions of this process facility respectively. Another section of my PhD research work focused on the life cycle assessment (LCA) of commonly used dairy feeds in the U.S. Greenhouse gas (GHG) emissions analysis was conducted for cultivation, harvesting, and production of common dairy feeds used for the production of dairy milk in the U.S. The goal was to determine the carbon footprint [grams CO2 equivalents (gCO2e)/kg of dry feed] in the U.S. on a regional basis, identify key inputs, and make recommendations for emissions reduction. The final section of my Ph.D. research work was an LCA of a single dairy feed mill located in Michigan, USA. The primary goal was to conduct a preliminary assessment of dairy feed mill operations and ultimately determine the GHG emissions for 1 kilogram of milled dairy feed.

Optimierung der Energieeffizienz von Intralogistikressourcen am Beispiel des Kettenförderers

Dieser Artikel setzt sich mit den Einflussgrößen auf die Energieeffizienz von Intralogistikressourcen am Beispiel des Tragkettenförderers auseinander. Es wird beleuchtet durch welche Methoden der Energiebedarf und -verbrauch ermittelt werden kann und wie Abhängigkeiten und Wechselwirkungen der Einflussgrößen auf den Energieverbrauch bestimmt werden. Aus den Ergebnissen werden Maßnahmen abgeleitet, durch die der Energieverbrauch von Intralogistikressourcen reduziert werden kann. Zudem wird ein Ausblick auf Energieverbrauchserhöhungen durch die zeitliche Veränderung infolge von Verschleißerscheinungen gegeben. Die ermittelten Erkenntnisse bilden die Grundlage für die Erstellung eines Kostenmodells, das die real auftretenden Lebenszykluskosten für Energie und Instandhaltung transparenter als bestehende Kostenmodelle darstellt. Mit dem Modell sollen Energie- und Instandhaltungskosten über den Lebenszyklus verringert werden, indem die Instandhaltungsmaßnahmen aus Gesamtkostensicht optimal geplant werden.

Risk adjustment in aging societies

Background In Switzerland, age is the predominant driver of solidarity transfers in risk adjustment (RA). Concerns have been voiced regarding growing imbalances in cost sharing between young and old insured due to demographic changes (larger fraction of elderly >65 years and rise in average age). Particularly young adults aged 19–25 with limited incomes have to shoulder increasing solidarity burdens. Between 1996 and 2011, monthly intergenerational solidarity payments for young adults have doubled from CHF 87 to CHF 182, which corresponds to the highest absolute transfer increase of all age groups. Results By constructing models for age-specific RA growth and for calculating the lifetime sum of RA transfers we investigated the causes and consequences of demographic changes on RA payments. The models suggest that the main driver for RA increases in the past was below average health care expenditure (HCE) growth in young adults, which was only half as high (average 2% per year) compared with older adults (average 4% per year). Shifts in age group distributions were only accountable for 2% of the CHF 95 rise in RA payments. Despite rising risk adjustment debts for young insured the balance of lifetime transfers remains positive as long as HCE growth rates are greater than the discount rate used in this model (3%). Moreover, the life-cycle model predicts that the lifetime rate of return on RA payments may even be further increased by demographic changes. Nevertheless, continued growth of RA contributions may overwhelm vulnerable age groups such as young adults. We therefore propose methods to limit the burden of social health insurance for specific age groups (e.g. young adults in Switzerland) by capping solidarity payments. Conclusions Taken together, our mathematical modelling framework helps to gain a better understanding of how demographic changes interact with risk adjustment and how redistribution of funds between age groups can be controlled without inducing further selection incentives. Those methods can help to construct more equitable systems of health financing in light of population aging.

A review on bovine besnoitiosis: a disease with economic impact in herd health management, caused by Besnoitia besnoiti (Franco and Borges, 1916).

Bovine besnoitiosis is caused by the largely unexplored apicomplexan parasite Besnoitia besnoiti. In cows, infection during pregnancy often results in abortion, and chronically infected bulls become infertile. Similar to other apicomplexans B. besnoiti has acquired a largely intracellular lifestyle, but its complete life cycle is still unknown, modes of transmission have not been entirely resolved and the definitive host has not been identified. Outbreaks of bovine besnoitiosis in cattle were described in the 1990s in Portugal and Spain, and later several cases were also detected in France. More cases have been reported recently in hitherto unaffected countries, including Italy, Germany, Switzerland, Hungary and Croatia. To date, there is still no effective pharmaceutical compound available for the treatment of besnoitiosis in cattle, and progress in the identification of novel targets for intervention through pharmacological or immunological means is hampered by the lack of molecular data on the genomic and transcriptomic level. In addition, the lack of an appropriate small animal laboratory model, and wide gaps in our knowledge on the host-parasite interplay during the life cycle of this parasite, renders vaccine and drug development a cost- and labour-intensive undertaking.

Demo -- Closer to Cloud-RAN: RAN as a Service

Commoditization and virtualization of wireless networks are changing the economics of mobile networks to help network providers (e.g., MNO, MVNO) move from proprietary and bespoke hardware and software platforms toward an open, cost-effective, and flexible cellular ecosystem. In addition, rich and innovative local services can be efficiently created through cloudification by leveraging the existing infrastructure. In this work, we present RANaaS, which is a cloudified radio access network delivered as a service. RANaaS provides the service life-cycle of an ondemand, elastic, and pay as you go 3GPP RAN instantiated on top of the cloud infrastructure. We demonstrate an example of realtime cloudified LTE network deployment using the OpenAirInterface LTE implementation and OpenStack running on commodity hardware as well as the flexibility and performance of the platform developed.