Effects of melting temperature on the broadband infrared luminescence of bi-doped and Bi/Dy co-doped chalcohalide glasses

Bismuth (Bi)-doped and Bi/Dy co-doped chalcohalide glasses are investigated as promising materials for amplifiers in optical communication. The samples synthesized at lower melting temperatures (MTs) are characterized by more intensified infrared emissions. With respect to the redox process of a liquid mixture at different MTs, we attribute an emission at 1230 nm to low-valent Bi ions. The lower MT favors the formation of LVB ions, i.e. Bi+ or Bi2+, while the higher MT promotes the production of higher-valent Bi ions Bi3+. An enhanced broadband infrared luminescence with the full-width at half-maximum over 200 nm is achieved from the present Bi/Dy co-doped chalcohalide glasses.

Ultrabroad infrared luminescences from Bi-doped alkaline earth metal germanate glasses

We report on ultrabroad infrared (IR) luminescences covering the 1000-1700-nm wavelength region, from Bi-doped 75GeO(2) 20RO-5Al(2)O(3) 1B(2)O(3) (R = Sr, Ca, and Mg) glasses. The full width at half-maximum of the IR luminescences excited at 980 nm increases (315 -> 440 -> 510 nm) with the change of alkaline earth metal (Mg2+ -> Ca2+ -> Sr2+). The fluorescence lifetime of the glass samples is 1725, 157, and 264 mu s when R is Sr, Ca, and Mg, respectively. These materials may be promising candidates for broad-band fiber amplifiers and tunable laser resources.

Ultrabroad infrared luminescence from Bi-doped aluminogermanate glasses

We report ultrabroad infrared luminescence from Bi-doped aluminogermanate glasses. The infrared luminescence almost covers the whole low loss wavelength region (1200-1650 nm) of silica glass fiber when excited by a diode laser at 980 nm. The full width at half maximum (FWHM) of the luminescence is 510 nm. The luminescence peak can be divided into three Gaussian peaks, and the fluorescence lifetime of the three emissions are 297 mu s, 470 mu s and 1725 mu s, respectively. These fluorescence properties indicate that the glasses are promising material for broadband optical amplifiers. (C) 2007 Elsevier Ltd. All rights reserved.

稀土离子掺杂的多组分玻璃光纤

abstract {Rare earth ions doped multi-component glass fibers have important application in broad band fiber amplifier and up-conversion fiber lasers. In this paper, the mechanism and the progress of study on rare earth ions doped multi-component glass fibers in broad band fiber amplifier and up-conversion fiber lasers are introduced and reviewed. The questions and the applications of rare earth ions doped multi-component glass fibers in the future are also prospected. Based on the present research progress, it is suggested to further study the tellurite and bismuth glasses, which are used as fiber materials in broad band fiber amplifier. To up-conversion fiber laser, it is still need to further investigate novel glasses, which has low phonon energy and good physical and chemical properties.}

SiO2 对Bi2O3-B2O3 玻璃体系光学、热学及结构的 影响

Glasses with compositions 50Bi2O3-xB2O3- (50-x)SiO2(x=0, 10, 20, 30, 40, 50) in mol% have been prepared by using a normal melt-quench technique. The effect of SiO2 addition on thermal stability, optical properties and structural characteristic on Bi2O3-B2O3 glass were systematically investigated by using XRD, DTA, ultraviolet-visible transmittance spectra, midinfrared transmittance spectra and Raman spectra. The experimental results demonstrate that, with the addition of SiO2, thermal stability of glass samples has been obviously improved. Once the amount of SiO2 is too much, the glass samples tend to be phase seperation which results in the decrease of thermal stability. With increasing SiO2 content, the UV cutoff edge firstly shifts to short-wave band and then shifts to long-wave band, and the transmittance of mid-infrared has been greatly improved. With substitution of SiO2 for B2O3, the [BO3] triangles and [BO4] tetrahedral groups are gradually replaced by [SiO4]. [BiO6] octahedral and [SiO4] tetrahedral units are connected forming a vibrational mode of Bi-O-Si. The physical chemistry and optical performance of Bi2O3-B2O3 glass were greatly improved by addition of SiO2.

Intense frequency upconversion luminescence in Yb3+/Tm3+-codoped oxychloride germanate glasses

Yb3+/Tm3+-codoped oxychloride germanate glasses for developing potential upconversion lasers have been fabricated and characterized. Structural properties were obtained based on the Raman spectra analysis, indicating that PbCl2 plays an important role in the formation of glass network and has an important influence on the maximum phonon energies of host glasses. Intense blue and weak red emissions centered at 477 and 650 nm, corresponding to the transitions (1)G(4) -> H-3(6) and (1)G(4) -> H-3(4), respectively, were observed at room temperature. With increasing PbCl2 content, the intensity of blue (477 nm) emission increases significantly, while the red (650 nm) emission increases slowly. The results indicate that PbCl2 has more influence on the blue emissions than the red emission in oxychloride germanate glasses. The possible upconversion mechanisms are discussed and estimated. Intense blue upconversion luminescence indicates that these oxychloride germanate glasses can be used as potential host material for upconversion lasers. C (c) 2005 Springer Science + Business Media, Inc.

Frequency upconversion fluorescence emission of Er3+-doped oxychloride germanate glass

Frequency upconversion fluorescence property of Er3+-doped oxychloride germanate glass is investigated. Intense green and red emissions centred at 525, 546, and 657nm, corresponding to the transitions H-2(11/2) -> I-4(15/2), S-4(3/2) -> 4I(15/2), and F-4(9/2) -> I-4(15/2), respectively, were simultaneously observed at room temperature. The quadratic dependence of the 525, 546, and 657nm emissions on excitation power indicates that a two-photon absorption process occurs under 975nm laser diode (LD) excitation. The Raman spectrum investigation indicates that oxychloride germanate glass has the maximum phonon energy at similar to 805 cm(-1). The thermal stability of this oxychloride germanate glass is evaluated by differential scanning calorimetry, and thermal stability factor Delta T (Delta T = T-x-T-g) is 187 degrees C. Intense upconversion luminescence and good thermal stability indicate that Er3+-doped oxychloride germanate glass is a promising upconversion laser material.

Upconversion emission in Er3+ doped novel bismuthate glass

Novel Er3+-doped bismuth lead strontiam glass was fabricated and characterized, and the absorption spectrum and upconversion spectrum of the glass were studied. The Judd-Ofelt intensity parameters Omega(t)(t = 2, 4, 6) were found to be Omega(2) = 3.27 x 10(-20) cm(2), Omega(4) = 1.15 x 10(-20) cm(2), and Omega(6) = 0.38 x 10(-20) cm(2). The oscillator strength, the spontaneous transition probabilities, the fluorescence branching ratios, and excited state lifetimes were also measured and calculated. The upconversion emission intensity varies with the power of infrared excitation intensity. A plot of log I-up vs log I-IR yields a straight line with slope 1.86, 1.88 and 1.85, corresponding to 525, 546, and 657 nm emission bands, respectively, which indicates that a two-photon process for the red and green emission.

熔制条件对铋酸盐玻璃性质的影响

采用传统的玻璃熔融法制备了组成为60Bi2O3-20B2O3-15SiO2-5La2O3(mol%)的铋酸盐玻璃， 系统研究了不同工艺过程对玻璃性能的影响. 分析了样品ICP的成分，扫描电镜，X-射线衍射谱， 差热分析和紫外-可见-近红外透过光谱测试. 结果表明：使用刚玉坩埚能提高玻璃的抗析晶稳定性 和透过率，陶瓷坩埚和白金坩埚均受到严重腐蚀，玻璃组分也随之发生很大变化. 当熔制温度从1 100 ℃变化到1 300 ℃时，玻璃的颜色从浅黄色变到深红棕色. 尤其是白金粒子被腐蚀进入玻璃液 后，玻璃中很容易形成纳米颗粒或者团聚形成胶体粒子，在玻璃中形成色散源，加深玻璃的颜色， 降低透过率. 1 300 ℃下，白金粒子起到晶核剂的作用，生成Bi2Pt2O7和BiB3O6晶相，导致玻璃失透.

Effects of thermal treatment on broadband near-infrared emission from Bi-doped chalcohalide glasses

GeGaSKBr glass with Bi ions as emission centers were fabricated. An intense emission centered at around 1230 nm with the width of more than 175 nm was observed by 808 nm photo-excitation of the glass. Lower quenching rate and thermal treatment promote micro-crystallization process, thus strengthening the emission. Crown Copyright (c) 2008 Published by Elsevier Ltd. All rights reserved.

Broadband infrared luminescence from Li2O-Al2O3-ZnO-SiO2 glasses doped with Bi2O3

The broadband emission in the 1.2 similar to 1.6 mu m region from Li2O-Al2O3-ZnO-SiO2 ( LAZS) glass codoped with 0.01mol.% Cr2O3 and 1.0mol.% Bi2O3 when pumped by the 808nm laser at room temperature is not initiated from Cr4+ ions, but from bismuth, which is remarkably different from the results reported by Batchelor et al. The broad similar to 1300nm emission from Bi2O3-containing LAZS glasses possesses a FWHM ( Full Width at Half Maximum) more than 250nm and a fluorescent lifetime longer than 500 mu s when excited by the 808nm laser. These glasses might have the potential applications in the broadly tunable lasers and the broadband fiber amplifiers. (c) 2005 Optical Society of America.

GeO2 : Bi, M (M = Ga, B) glasses with super-wide infrared luminescence

Broadband infrared luminescence covering the optical telecommunication wavelength region of 0, E and S bands was observed in GeO2: Bi, M (M = Ga, B) glasses prepared by conventional melting-quenching technique. The luminescence with a maximum at around 1320 nm possesses a full width at half maximum larger than 300 nm and mean fluorescent lifetime longer than 500 mus when excited by an 808 nm-laser. These glasses may have potential applications in widely tunable laser and super-broadband optical amplifier for the optical communications. (C) 2005 Elsevier B.V. All rights reserved.

超宽带光纤放大器用的新型掺铋发光材料

最近，一种新型的掺铋发光材料引起了人们的关注。这种发光材料有长的荧光寿命（τ＞200μs），在800nm激光激发下发射波长在1200～1600nm区间的超宽带荧光（荧光半高宽FWHM＞200nm），其发光性质与以往文献中报道的Bi^3＋或Bi^2＋掺杂的发光材料的性质截然不同；光发射截面（σem）是光掺铒光纤放大器玻璃（EDFAG）的2～3倍，其σem×FWHM值是EDFAG的10倍左右，σem×τ值是掺Ti^3＋蓝宝石的3倍左右。

Identificação da formação de titanato de bário a partir de mistura reacional calcinada em diferentes temperaturas via difração de raios X, espectroscopia fotoacústica e análise térmica

Os materiais ferroelétricos têm sido utilizados em muitas áreas da tecnologia e da ciência, pois possuem um grande número de aplicações, como: sensores; transdutores; capacitores; dispositivos ópticos; dentre outras. A busca por novos materiais cerâmicos ferroelétricos tem sido grande. Um dos materiais cerâmicos ferroelétricos mais estudados é o titanato de bário (BT). São vários os métodos de produção e caracterização do titanato de bário. Neste trabalho, pós cerâmicos de titanato de bário foram obtidos por reação do estado sólido a partir de misturas reacionais calcinadas em diferentes temperaturas entre 400C e 900C. Foram três as misturas reacionais: não dopadas; dopadas com 1%; e dopadas com 5% de dióxido de cério (CeO2). A identificação da formação do BT, nos pós cerâmicos produzidos, foi feita a partir de três técnicas de caracterização: difração de raios X (DRX); espectroscopia fotoacústica (PAS); e técnicas de análise térmica. Com a técnica DRX, difratogramas mostraram que a plena formação do titanato de bário ocorreu a partir da temperatura de calcinação de 700C. Para a amostra não dopada com cério e calcinada a 800C, houve deslocamento de todos os picos de difração. Nas amostras dopadas com dióxido de cério houve deslocamento de todos os picos de difração, em relação as amostras não dopadas. Observou-se também que nas amostras dopadas com 5% de CeO2, e calcinadas a 700C e 800C, resíduos de dióxido de cério foram observados nos difratogramas. Com a técnica PAS, espectros de absorção foram obtidos. Foi possível observar uma grande diferença de absorção da amostra calcinada a 600 e 630C, indicando a formação do titanato de bário a partir da temperatura de 630C, nas amostras sem a dopagem dióxido de cério. Houve um alargamento nas bandas de absorção a partir da temperatura de 600C, quando o dióxido de cério entrou na matriz. Foi também possível determinar as energias de band-gap das amostras utilizando o método de Tauc. Com as técnicas de análise térmica, em especial através da técnica termogravimétrica (TG/DTG), foi comprovado que até 400C não havia formação de titanato de bário. Visto que nesta temperatura de calcinação houve a maior perda de massa durante a rampa de aquecimento. O início da formação do titanato de bário foi observado a partir da temperatura de calcinação de 500C, assim como nas técnicas DRX e PAS. Portanto, com os resultados apresentados, foi demonstrada a identificação da formação do titanato de bário nas misturas reacionais calcinadas, com auxílio das potencialidades das três técnicas utilizadas.

Unexpected controllable pair-structure in ferroelectric nanodomains.

The imminent inability of silicon-based memory devices to satisfy Moore's Law is approaching rapidly. Controllable nanodomains of ferroic systems are anticipated to enable future high-density nonvolatile memory and novel electronic devices. We find via piezoresponse force microscopy (PFM) studies on lead zirconate titanate (PZT) films an unexpected nanostructuring of ferroelectric-ferroelastic domains. These consist of c-nanodomains within a-nanodomains in proximity to a-nanodomains within c-domains. These structures are created and annihilated as pairs, controllably. We treat these as a new kind of vertex-antivertex pair and consider them in terms of the Srolovitz-Scott 4-state Potts model, which results in pairwise domain vertex instabilities that resemble the vortex-antivortex mechanism in ferromagnetism, as well as dislocation pairs (or disclination pairs) that are well-known in nematic liquid crystals. Finally, we show that these nanopairs can be scaled up to form arrays that are engineered at will, paving the way toward facilitating them to real technologies.