Station hydrologique de Vridi et stations cotières de 1986 à 1988

In this report were gathered accurate data from coastal stations and from a hydrological station. The used experiments took place from 1986 to 1988.

Stations cotières et station hydrologique cotière d'Abidjan années 1977, 1978 et 1979

On tables 1 to 12, daily beach surface temperatures are presented. These temperatures are also ploted on figures 2 to 5 in daily values and in 7, 15, 30 days means. Salinity variations are less important than these of temperature (Fig. 6, 7). It follows that during upwelling period, variations of dynamic height anomaly are closely correlated with temperature (Fig. 6 and 8).

Dix ans de mesures de biomasses de zooplancton a la station cotière d'Abidjan: 1969-1979

Graphs of variations of zooplankton biomasses expressed as ash-free dry weight (i.e. organic matter) are presented for the 1969-1979 period. The graph of the average year shows: an enrichment season from mid-July till mid-November in which the biomass is 2.3 times higher than the rest of the year and characterized by a slight decrease of the biomass in late August or early September. The warm season is divided into a period of moderate biomass from November till February, a period of moderate biomass from November till February and a period of steady decline of the biomass till the start of the upwelling at the end of June.

Making experiment station results more useful to African fish farmers

Rather than using more or less ideal conditions for setting experimental controls, the use of conditions similar to those likely to be encountered by farmers should produce research results which are realistically achievable on the farm. ICLARM has developed an approach to farmer-led experimentation which utilizes a spreadsheet to collate and analyze data collected from participating farmers. The simulation of actual management practices utilized by farmers produced results in replicated on-station trials which were within 11% of net yields on-farm. In addition to giving researchers a tool for comparing farm and station management practices, giving farmers a realistic indication of what yields will be if a technology is adopted should help overcome the problems of disillusionment often encountered when farm results fall below those expected by researchers on the basis of experiment station studies.

Sensitivity of wear rates in the micro-scale abrasion test to test conditions and material hardness

Micro-scale abrasion (ball cratering) tests were performed with different combinations of ball and bulk specimen materials, under different test conditions, such as load and abrasive slurry concentration. Wear modes were classified into two types: with rolling particle motion and with grooving particle motion. Wear rates observed with rolling particle motion were relatively insensitive to test conditions, whereas with grooving motion they varied much more. It is suggested that rolling abrasion is therefore a more appropriate mode if reproducible test results are desired. The motion of the abrasive particles can be reliably predicted from the knowledge of hardnesses and elastic properties of the ball and the specimen, and from the normal load and the abrasive slurry concentration. General trends in wear resistance measured in the micro-scale abrasion test with rolling particle motion are similar to those reported in tests with fixed abrasives with sliding particle motion, although the variation in wear resistance with hardness is significantly smaller. © 2004 Published by Elsevier B.V.

Sources of variability in the free-ball micro-scale abrasion test

In the 'free-ball' version of the micro-scale abrasion or ball-cratering test the rotating ball rests against a tilted sample and a grooved drive shaft. Tests under nominally identical conditions with different apparatus commonly show small but significant differences in measured wear rate. An indirect method has been developed and demonstrated for continuous on-line measurement of the coefficient of friction in the free-ball test. Experimental investigation of the effects of sample tilt angle and drive shaft groove width shows that both these factors influence the stability of the rotation of the ball, and the shape of the abrasive slurry pool, which in turn affect the coefficient of friction in the wear scar area and the measured wear rate. It is suggested that in order to improve the reproducibility of this method the geometry of the apparatus should be specified. For the apparatus used in this work with a steel ball of 25 mm diameter, a sample tilt angle of 60-75° and a shaft groove width of about 10mm provided the most stable ball motion and a wear rate which showed least variability. © 2004 Elsevier B.V. All rights reserved.