Effect of resin composites with sodium trimetaphosphate with or without fluoride on hardness, ion release and enamel demineralization

Purpose: To evaluate the effect of the addition of sodium trimetaphosphate (TMP) with or without fluoride on enamel demineralization, and the hardness and release of fluoride and TMP of resin composites. Methods: Bovine enamel slabs (4x3x3 mm) were prepared and selected based on initial surface hardness (n= 96). Eight experimental resin composites were formulated, according to the combination of TMP and sodium fluoride (NaF): TMP/NaF-free (control), 1.6% sodium fluoride (NaF), and 1.5%, 14.1% and 36.8% TMP with and without 1.6% NaF. Resin composite specimens (n= 24) were attached to the enamel slabs with wax and the sets were subjected to pH cycling. Next, surface and cross-sectional hardness and fluoride content of enamel as well as fluoride and TNT release and hardness of the materials were evaluated. Data were statistically analyzed using ANOVA (P< 0.05). Results: The presence of fluoride in enamel was similar in fluoridated resin composites (P> 0.05), but higher than in the other materials (P< 0.05). The combination of 14.1% TMP and fluoride resulted in less demineralization, especially on lesion surface (P< 0.05). The presence of TMP increased fluoride release from the materials and reduced their hardness.

Time reduction of light curing: Influence on conversion degree and microhardness of orthodontic composites

Introduction: The aim of this study was to assess the influence of curing time and power on the degree of conversion and surface microhardness of 3 orthodontic composites. Methods: One hundred eighty discs, 6 mm in diameter, were divided into 3 groups of 60 samples according to the composite used-Transbond XT (3M Unitek, Monrovia, Calif), Opal Bond MV (Ultradent, South Jordan, Utah), and Transbond Plus Color Change (3M Unitek)-and each group was further divided into 3 subgroups (n = 20). Five samples were used to measure conversion, and 15 were used to measure microhardness. A light-emitting diode curing unit with multiwavelength emission of broad light was used for curing at 3 power levels (530, 760, and 1520 mW) and 3 times (8.5, 6, and 3 seconds), always totaling 4.56 joules. Five specimens from each subgroup were ground and mixed with potassium bromide to produce 8-mm tablets to be compared with 5 others made similarly with the respective noncured composite. These were placed into a spectrometer, and software was used for analysis. A microhardness tester was used to take Knoop hardness (KHN) measurements in 15 discs of each subgroup. The data were analyzed with 2 analysis of variance tests at 2 levels. Results: Differences were found in the conversion degree of the composites cured at different times and powers (P < 0.01). The composites showed similar degrees of conversion when light cured at 8.5 seconds (80.7%) and 6 seconds (79.0%), but not at 3 seconds (75.0%). The conversion degrees of the composites were different, with group 3 (87.2%) higher than group 2 (83.5%), which was higher than group 1 (64.0%). Differences in microhardness were also found (P < 0.01), with lower microhardness at 8.5 seconds (35.2 KHN), but no difference was observed between 6 seconds (41.6 KHN) and 3 seconds (42.8 KHN). Group 3 had the highest surface microhardness (35.9 KHN) compared with group 2 (33.7 KHN) and group 1 (30.0 KHN). Conclusions: Curing time can be reduced up to 6 seconds by increasing the power, with a slight decrease in the degree of conversion at 3 seconds; the decrease has a positive effect on the surface microhardness.

Efeito da partícula e do momento de jateamento na caracterização superficial da zircônia e na resistência de união com cimento resinoso

Pós-graduação em Reabilitação Oral - FOAR

Avaliação da rugosidade superficial de restaurações estéticas e do esmalte adjacente após o uso de diferentes instrumentos rotatórios de acabamento e polimento

Pós-graduação em Odontologia - ICT

Efeitos da rugosidade superficial nas propriedades de passivação de monocamadas orgânicas automontadas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo do desempenho de barreiras de geotêxtil para contenção de sedimentos carreados pelo escoamento superficial

Pós-graduação em Engenharia Civil e Ambiental - FEB

Análise da superfície de cerâmicas de dissilicato de lítio após imersão em soluções ácidas e a base de flúor

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de uma nova composição de agente clareador sobre a microdureza do esmalte: associação do trimetafosfato de sódio e fluoreto de sódio ao peróxido de hidrogênio a 10%

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem e otimização por metodologia de superfícies de resposta: um estudo em arames de aço SAE 9254 para molas automobilísticas

Pós-graduação em Engenharia Mecânica - FEG

Mapeamento geoestatístico da permeabilidade superficial no entorno do Ribeirão Claro: e simulação da possibilidade de sua contaminação

The evaluation of soil permeability throughout the weathering profile is one of the most important features to be considered in environmental studies. This study, developed from field testing and analysis of data obtained by geostatistical methods, aims at mapping the permeability around the Ribeirão Claro river. The intent is to simulate an accident with toxic liquids where soil permeability is of fundamental importance. Another purpose of the research was to determine the minimum time that, in the event of an accident, a possible contaminant to reach the water table level and be routed to the nearest drain, in this case, the Ribeirao V Claro river constitutes fundamental information. The studied area of approximately 4 km² is located within the UNESP-Rio Claro campus, consisting of colluvial soil from Fm. Rio Claro superimposed on residual soil of Fm. Corumbataí. The method used to determine the permeability is the concentric cylinders performed on a sampling grid with 64 points containing spacing of 5 meters EW and 10 meters NS. In the places of permeability tests were collected samples for laboratory determination of the percentage of fines. From particle size analysis was performed and analysis statistical and geostatistical on this data. The histogram was based on the statistical studies, and the semivariograms were based on geostatistical estimation methods. Based on the comparison between the maps and the data obtained, it was determined that the percentage of fines in colluvial surface soil has little influence on permeability, which the proximity to the Ribeirao Claro river, the eastern portion, a factor that influences the distribution of permeability values

Estudo em fadiga no aço API 5L X80 soldado pelo processo HF/ERW

The technological advancement in order to improve the methods of obtaining energy sources such as oil and natural gas is mainly motivated by the recent discovery of oil reserves. So, increasingly , there is a need for a thorough knowledge of the materials used in the manufacture of pipelines for transportation and exploration of oil and natural gas. The steels which follow the API standard (American Petroleum Institute), also known as high strenght low alloy (hsla), are used in the manufacture of these pipes, as they have, with their welded joints, mechanical properties to withstand the working conditions to which these ducts will be submitted . The objective of this study is to evaluate the fatigue behavior in microalloyed steel grade API 5L X80 welded by process HF / ERW . For this, axial fatigue tests to obtain S-N curve (stress vs. number of cycles ) were conducted. To complement the study, it was performed metallographic , fractographic , Vickers hardness tests and tensile tests to characterize the mechanical properties of the steel and check whether the values satisfy the specifications of the API 5L standard . From the fatigue tests , it was concluded that the surface finish influences directly on the fatigue life of the material

Melhoria da qualidade de um processo de usinagem utilizando as técnicas de avaliação de Taguchi

Delivering to the customers a product or service with the expected quality associated to the huge competitiveness that exists in the market nowadays, has been making organizations increasingly focus on quality planning using techniques which are directed towards the continuous improvement process and production optimization. Thus, this paper aims to improve a machining process using the techniques of experimental design to the optimization and this also includes the analysis of the measurement system. For this purpose, the alloy Nimonic 80A, a nickel base superalloy, was used in the process due to its widespread use for high temperatures, applying this study the robust method proposed by Genichi Taguchi, determining the influence of the factors considered input variables, cutting speed, feed rate, depth of cut, type of tool, lubrication, and material hardness, in the output or response variable, surface roughness, concluding with the use of Taguchi orthogonal array L16 and by analysis of ANOVA that the factor feed rate is significant and offers greater effect on the response variable studied, should be set to 0,12mm/rev. Moreover, the factor type of tool has more influence on the process when compared to other factors, being CP250 the one more suitable to the process. Lastly, the interaction feed rate x cutting speed provides greater significance in the process regarding to surface roughness variable, being the best match between them 0,12mm/rev to the feed rate and 90m/min to the cutting speed. In order to evaluate the measurement system, it was applied the repeatability and reproducibility method (R&R), through which we saw that the system needs improvement (R & R = 88.04% >>> 30%) as the value found in the study was well above compared to the one that classifies the system as inappropriate

Carta geotécnica de suscetibilidade aos processos de dinâmica superficial na região do Bairro do Peão, Piracaia (SP)

This research presents the result of the engineering geological mapping in a 1:50.000 scale, in Bairro do Peão region, in Piracaia (SP), represented by means of homogeneous units which are susceptible to superficial dynamic processes. To serve as basis for the elaboration of a Chart of Susceptibility to Processes of Superficial Dynamic, a series of physical samples was collected, considering erosive processes and registers of information of usage and soil occupation. The procedure used for elaborating the geotechnical chart is based on Vedovello (2000), which suggests the physiographic compartimentation of the area through photointerpretation and further geotechnical characterization of the selected samples. The geotechnical characterization of the samples was made by identifying the features and properties of the material and forms of the physical environment determining the geotechnical conditions through geological-geotechnical profile descriptions typical of/ peculiar to each unit defined in the area. Thus, for each unit selected, the susceptibility level was established in very high, high, average and low, as well as the prevalent erosive processes.

Efeitos dos parâmetros de usinagem no acabamento superficial de materiais cerâmicos a verde

Pós-graduação em Engenharia Mecânica - FEB

Fadiga axial do aço inoxidável 15-5 PH tratado pela implantação iônica por imersão em plasma

When materials for application in aircraft structural components are studied, it must be considered that they will be submitted to cyclic loading, and this is an important parameter to design the study in fatigue life of the materials. Whereas, for example, a landing gear operation, the study of fatigue life and corrosion in the materials used in it is essential, especially when you want to use new techniques for surface treatments. The objective is to study the influence of surface treatment of immersion ion implantation nitrogen plasma, in axial fatigue of Stainless steel 15-5 PH in 39-42 HRC condition. Stainless steel 15-5 PH was tested in axial fatigue and corrosion in salt spray. It was also performed microindentation tests, optical microscopy for microstructural analysis and scanning electron microscopy for fractographic analysis. It was observed that the 3IP had no effect on the thickness of the material and not the hardness of it, and still provided a significant increase in fatigue life of the material