Preparation and properties of polyimide films codoped with barium and titanium oxides

Polyimide hybrid films containing bimetalic compounds were obtained by codoping poly(amic acid) with a barium and titanium precursor prepared from BaCO3, Ti(OBu)(4), and lactic acid followed by casting and thermal curing. FTIR, WAXD, and XPS measurements showed that barium and titanium precursor could be transformed to BaTiO3 at a temperature above 650 degreesC, while the mixed oxides were only found in hybrid films. The measurements of TEM and AFM indicated a homogeneous distribution of inorganic phase with particle sizes less than 50 nm. The hybrid films exhibited fairly high thermal stability, good optical transparency, and promising mechanical properties. The incorporation of 10 wt % barium and titanium oxide lowered surface and volume electrical resistivity by 2 and 5 orders, respectively, increasing dielectric constant from 3.5 to 4.2 and piezoelectric constant from 3.8 to 5.2 x 10(-12) c/N, relative to the nondoped polyimide film.

Studies on electrocatalytic performance of titanium oxide electrode modified with Pt toward the oxidation of methanol

Electrocatalytic performance of the Pr-TiOx/Ti electrode prepared with electrochemical reduction-oxidation method toward the oxidation of methanol has been studied, The experimental results showed that the Pt-TiOx/Ti electrode has a high electrocatalytic activity and good stability for the electrocatalytic oxidation of methanol, By means of electrochemical, XPS, STM and in-situ FTIR techniques, it was found that one reason for the electrode to exhibit an excellent performance is attributed to the high dispersion between nanosized Pt and TiOx particles, The low adsorption ability of the intermediate derived from methanol, such as linearly adsorbed CO species on the electrode surface due to the interaction between Pt and TiOx, also results in the excellent performance.

X-ray crystal structure and molecular mechanics calculations of (2,6-iso-dipropyl-phenylamide) dimethyl (tetra-methylcyclopenta-dienyl) silane titanium dichloride

Crystal and molecular structure of (2.6-dipropylphenylamide) dimethyl (tetra-methyl cyclopentadienyl) silane titanium dichloride (I) was fully characterized by X-ray diffraction. The crystal is obtained from a mixture of ether/hexane as orthorhombic. with a = 12.658 (3) Angstrom. b = 16.62 (3) Angstrom. c = 11.760 (2) Angstrom. V = 2474.2 (9) Angstrom(3). Z = 4, space group Pnma. R = 0.0399; Componud I compose of the pi-bounded ring with its dimethylsilyl-dipropyl phenyl amido group and the two terminal chloride atoms coordinated to central metal to form a so-called constrained geometry catalyst (CGC) structure. The result of molecular mechanics (MM) calculations on compound I shows that bond lengths and bond angles from the MM calculation are comparable to the data obtained from the X-ray diffraction study. The relation of the structure of CGCs and their catalytic activity by MM calculations is also discussed.

Amperometric tyrosinase biosensor based on a sol-gel-derived titanium oxide-copolymer composite matrix for detection of phenolic compounds

A new type of tyrosinase biosensor was developed for the detection of phenolic compounds, based on the immobilization of tyrosinase in a sol-gel-derived composite matrix that is composed of titanium oxide sol and a grafting copolymer of poly(vinyl alcohol) with 4-vinylpyridine. Tyrosinase entrapped in the composite matrix can retain its activity to a large extent owing to the good biocompatibility of the matrix. The parameters of the fabrication process and the variables of the experimental conditions for the enzyme electrode were optimized. The resulting sensor exhibited a fast response (20 s), high sensitivity (145.5 muA mmol(-1) 1) and good storage stability. A detection limit of 0.5 muM catechol was obtained at a signal-to-noise ratio of 3.

Amperometric determination of thiosulfate at a surface-renewable nickel(II) hexacyanoferrate-modified carbon ceramic electrode

Graphite powder-supported nickel(II) hexacyanoferrate (NiHCF) was prepared by the in situ chemical deposition method and then dispersed into methyltrimethoxysilane-derived gels to form a conductive composite. The composite was used as electrode material to construct a surface-renewable three-dimensional NiHCF-modified carbon ceramic electrode. Electrochemical behavior of the chemically modified electrode was well characterized using cyclic and square-wave voltammetry. The electrode presented a good electrocatalytic activity toward the oxidization of thiosulfate and thus was used as an amperometric sensor for thiosulfate in the photographic waste effluent. In addition, the electrode exhibited a distinct advantage of surface-renewal by simple mechanical polishing, as well as simple preparation, good chemical and mechanical stability. (C) 2001 Elsevier Science B.V. All rights reserved.

A nickel molybdenum phosphate with tunnel: Hydrothermal synthesis and structure of (NH3CH2CH2NH3)(4)center dot(NH3CH2CH2NH2)center dot Na center dot[Ni2Mo12O30(PO4)(HPO4)(4)(H2PO4)(3)]center dot 6H(2)O

A nickel molybdenum phosphate, (NH3CH2CH2NH3)(4).(NH3CH2CH2NH2). Na .[Ni2Mo12O30(PO4)(HPO4)(4)(H2PO4)(3)]. 6H(2)O, invoicing molybdenum present in V oxidation, has been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction. Deep brown-red crystals are formed in the triclinic system, space group P (1) over bar, a = 12,011(2), b = 14,612(3), c = 21.252(4) Angstrom, alpha = 80.54(2)degrees, beta = 83.10(2)degrees, gamma = 76.29(2)degrees, V = 3561.4(12) Angstrom(3), Z = 2, lambda(MoK alpha) = 0.71073 Angstrom (R(F) = 0.0529 for 9880 reflections), Data mere collected on a Siemens P4 diffractometer at 20 degrees C in the range of 1.75 degrees < theta < 23.02 degrees using the omega-scan technique. The structure was solved by direct methods using the program SHELXTL-93 and refined with the method of fun-matrix least-squares on F-2. The structure of the title compound may be considered to be two [Mo6O15(HPO4)(H2PO4)(3)](5-) units bonded together with a nickel atom, although several P-O groups are not protonated on account of coordination with a Na+ cation, The one-dimensional tunnels were formed in the solid of the title compound. A probe reaction of the oxidation of acetaldehyde with H2O2 using the title compound as catalyst was carried out in a liquid- solid system, showing that the title compound had high catalytic activity in the reaction, (C) 1999 Academic Press.

In-situ Fourier transform infrared spectroelectrochemistry as a probe of the glassy carbon electrode chemically modified by nickel (II)-cyanometallates

A new nickel (II)-cyanometallates modified on glassy carbon electrode was prepared by a new method and studied by cyclic voltammetry and in situ Fourier transform infrared (FTIR) spectroelectrochemistry. It was found that the NiHCF film existed in two forms: Ni2Fe(II)-(CN)(6) and M2NiFe(II)(CN)(6), Fe(CN)(3)(6-) codeposited in the NiHCF film existing in free cation or bridged-bond state depended on the property of the cations in electrolyte: in NaCl and LiCl solution, it is in bridges-bonded, but in HCl and KCl, it is free.

Electrocatalytic oxidation of methanol at the titanium oxide electrode modified with Pt microparticles

The electrocatalytic oxidation of methanol at the Titanium oxide (TiOx, x<2) film modified with Pt microparticles has been studied. The results show that the modified electrodes exhibit a significant electrocatalytic activity and good stability for the oxidation of methanol. Under the optimal conditions, the peak current density at 0.58 V for the oxidation of methanol in the positive-going sweep is about 526 mA/cm(2) at the scan rate of 5 mV/s in 0.5 mol/L CH3OH and 0.5 mol/L H2SO4 solution and the over potential of the methanol oxidation at the modified electrode increases about 30 similar to 40 mV after 70 minutes at the current density of 100 mA/cm(2) and 50 mA/cm(2). The enhanced electrocatalytic activity and good stability are ascribed to the high dispersion of Pt microparticles in and on the TiOx film and the synergistic effect between Pt microparticles and TiOx.

Synthesis, properties and crystal structure of a heteropoly compound containing titanium

K4H2CoW12O40. 2Ti02 . 9H(2)O crystallizes from an aqueous solution of Na2WO4, Co(OAc)(2) and Ti(SO4)(2). The compound has very similar i.r. and u.v. spectra to those of [CoW12O40](6-) and [CoW11TiO40](8-) but its polarographic behaviour is different from that of [CoW11TiO40](8-) and exhibits only reduction of tungsten(VI). A single crystal structural analysis indicates that this compound consists of the heteropolyanion [CoW12O40](6-), titanium-oxygen chain, potassium ions and water molecules.

Preparation of TiO2 Film through Hydrolysis of Titanium Butoxide and Interaction between Sensitizing Dyes and the Film

A method of preparation of stable, homogeneous and controlled thickness TiO2 film through hydrolysis of Ti(OC4H(9))(4) is introduced in detail. The structure and property of the film have been investigated by means of SEM and FT-IR techniques. The strong quenching effect between sensitizing dyes and TiO2 film is observed in their fluorescence spectra.

Syntheses and reactions of heterometallic complexes of nickel and copper with tetrathiotungstates. The molecular structures of [Ph(4)P](2)[S2W(mu-S)(2)Ni(S-2)] and W(mu-S)(4)Cu-2(PPh(3))(4)center dot py

Reaction of [Ph(4)P]2WS4 With NiCl2 in methanol solution in the presence of NaOCH3 leads to the formation of [Ph(4)P](2) [S2W(mu-S)(2)Ni(S-2)] (I) A Similar reaction between (NH4)(2)WS4 and NiCl2 under O-2 atmosphere in the presence of Ph(4)PCl or (n)Bu(4)NCl affords [Ph(4)P](2)([(S-2)W(O)(mu-S)(2)]Ni-2] (IIa) and [(n)Bu(4)N](2)([(S-2)W(O)(mu-S)(2)]Ni-2} (IIb) Under argon the same reaction gives [Ph(4)P](2)[Ni(WS4)(2)] (IIIa) and [(n)Bu(4)N](2)[Ni(WS4)(2)] (IIIb). [Ph(4)P](2)[Ni(WOS3)(2)] (IV) and [Ph(4)P](2)[Ni(WO2S2)(2)] (V) can be prepared from the reaction of [Ph(4)P]2WOS3 and [Ph(4)P]2WO2S2 with NiCl2. Treatment of (NH4)(2)WS4 with CuCl in the presence of PPh(3) in boiling pyridine produces W(mu-S)(4)Cu-2(PPh(3))(3) (VI), which can further react with excess PPh(3) to give W(mu-S)(4)Cu-2(PPh(3))(4) . py (VII). Complex I crystallizes in the space group P2(1)/n with the cell parameters: a = 20.049(4), b = 17.010(4), c = 14.311(7) Angstrom; beta = 110.24(3)degrees and Z = 4; R = 0.058 for 4267 independent reflections. The structural study confirms that complex I contains two terminal sulfide ligands, two bridging sulfide ligands, a side-on disulfide ligand, and a planar central W(mu-S)(2)Ni four membered ring. Complex VII crystallizes in the space group C2/c with the cell parameters: a = 26.436(8), b = 20.542(6), c = 19.095(8) Angstrom; beta = 125.00(3)degrees and Z = 4; R = 0.080 for 3802 independent reflections. The structural study reveals a perfect linear arrangement of the three metal atoms Cu-W-Cu.

Polymer-supported titanium catalysts for syndiotactic polymerization of styrene

Poly(styrene-co-acrylamide) (PSAm)-titanium complexes (PSAm . Ti) were prepared and characterized. It is found that the coordination number of acrylamide (Am) to Ti in the complexes is strongly dependent on Am content in PSAm, but not on [Am]/[Ti] ratio in the feed. The infrared and x-ray photoelectron spectra suggest that the polymer-supported complexes possess the structure [GRAPHICS] The catalytic behavior of the complexes in styrene polymerization is described. The catalytic activity is markedly affected by [Al]/[Ti] ratio in the complexes. C-13 NMR, IR, and DSC data indicate that the polystyrene obtained with PSAm . Ti/MAO (MAO = methylaluminoxane) is highly syndiotactic. Use of Et(3)Al and i-Bu(3)Al in place of MAO gives atactic polystyrene. The activities of the various aluminum compounds used as the cocatalysts decrease in the order: MAO > Et(3)Al > i-Bu(3)Al. The polymer-supported complexes show relatively high activity even after the complexes had been exposed to air for 19 h or higher polymerization temperature. (C) 1996 John Wiley & Sons, Inc.

Comparative study of Nickel-based perovskite-like mixed oxide catalysts for direct decomposition of NO

The mixed oxides LaNiO3, La0.1Sr0.9NiO3, La2NiO4 and LaSrNiO4 were prepared and used as catalysts for the direct decomposition of NO. The catalysts were characterized by means of XRD, XPS, O-2-TPD, NO-TPD and chemical analysis. By comparing the physico-chemical properties and catalytic activity for NO decomposition, a conclusion could be drawn as follows. The direct decomposition of NO over perovskite and related mixed oxide catalysts follows a redox mechanism. The lower valent metal ions Ni2+ and disordered oxygen vacancies seem to be the active sites in the redox process. The oxygen vacancy plays an important role favorable for the adsorption and activation of NO molecules on one hand and on the other hand for increasing the mobility of lattice oxygen which is beneficial to the reproduction of active sites. The presence of oxygen vacancies is one of the indispensable factors to give the mixed oxides a steady activity for NO decomposition.

DICHLORO(ETA(5)-CYCLOPENTADIENYL)([1-(4-METHOXYPHENYL)CYCLOHEXYL]-ETA(5)-CYCLOPENTADIENYL)TITANIUM(IV)

The title molecule, [TiCl2(C5H5)(C18H21O)], has a pseudotetrahedral bent metallocene structure in which the cyclopentadienyl ring is symmetrically bonded to Ti [range of Ti-C distances 2.36(1)-2.41(1)Angstrom], but the substituted cyclopentadienyl ring adopts asymmetrical bonding [Ti-C 2.33(1)-2.48(1)Angstrom] due to the interaction of the large substituent with the Cl(2) atom. The angle C(11)-C(1)-C(21) is 111.1(8)degrees with the large substituent occupying a cis position with respect to the substituted ring.

STUDIES ON THE PEROVSKITE-TYPE MIXED CATALYSTS OF TITANIUM SYSTEM FOR OXIDATIVE COUPLING OF METHANE - THE INFLUENCE OF CALCINATION TEMPERATURE

The correlations of the calcination temperature, structure and catalytic activity for the oxidative coupling of methane on the LiLa0.5Ti0.5O2+lambda catalysts whose main phase and major active phase is Perovskite-type ternary complex oxide LaTi1-yLiyO3-lambda have been studied. The surface and bulk structures of the catalysts were characterized by means of XRD, XPS, IR, BET and so on, The results cleary indicated that the effect of calcination temperature on the activity for the oxidative coupling of methane is twofold. On one hand, it is favorable for Li+ substitution for Ti3+ to enter into the lattice of LaTiO3 and produce more oxygen vacancies in which active oxygens are formed; however, excessively high calcination temperature make the amount of Li+ substitution for Ti3+ lower, due to a little change of structure or phases for the catalyst. On the other hand, the conversion of CH4 drops because of the decrease of surface area, when the calcination temperature is raised.