A maximum principle for infinite time asymptotically stable impulsive dynamic control systems

We consider an infinite horizon optimal impulsive control problems for which a given cost function is minimized by choosing control strategies driving the state to a point in a given closed set C ∞. We present necessary conditions of optimality in the form of a maximum principle for which the boundary condition of the adjoint variable is such that non-degeneracy due to the fact that the time horizon is infinite is ensured. These conditions are given for conventional systems in a first instance and then for impulsive control problems. They are proved by considering a family of approximating auxiliary interval conventional (without impulses) optimal control problems defined on an increasing sequence of finite time intervals. As far as we know, results of this kind have not been derived previously. © 2010 IFAC.

Comparison of FACTS STATCOM models for damping oscillations in power system due to small perturbations

This paper presents small-signal stability studies of a multimachine power system, considering Static Synchronous Compensators (STATCOM)and discussed control modes of the STATCOM. The Power Sensitivity Model(PSM)is used to represent the electric power system. The study is based on modal analysis and time domain simulations. The results obtained allow concluding that the STATCOM improves the stabilization in the electric power system. © 2011 IEEE.

Implementation of a DC-DC converter with variable structure control of switched systems

This paper presents a control method for a class of continuous-time switched systems, using state feedback variable structure controllers. The method is applied to the control of a two-cell dc-dc buck converter and a control circuit design using the software PSpice is proposed. The design is based on Lyapunov-Metzler-SPR systems and the performance of the resulting control system is superior to that afforded by a recently-proposed alternative sliding-mode control technique. The dc-dc power converters are very used in industrial applications, for instance, in power systems of hybrid electric vehicles and aircrafts. Good results were obtained and the proposed design is also inexpensive because it uses electric components that can be easily found for the hardware implementation. Future researches on the subject include the hardware validation of the dc-dc converter controller and the robust control design of switched systems, with structural failures. © 2011 IEEE.

Using serial bluetooth converters as a sensor link in networked control systems

Networked control systems (NCS) are distributed control system in which sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks which enable interoperability between existing wired and wireless systems. This paper presents the feasibility analysis of using a serial RS-232 to Bluetooth converter as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the converter capabilities. In addition the control performance of an implemented motor control system using the converter is analyzed. Experimental results led to the conclusion that serial RS-232 Bluetooth converters can be used to implement wireless networked control systems (WNCS) providing transmission rates and closed control loop times which are acceptable for NCS applications. © 2011 IEEE.

Design and implementation of a dc-dc converter based on variable structure control of switched systems

This paper presents a control method for a class of continuous-time switched systems, using state feedback variable structure controllers. The method is applied to the control of a non-trivial dc-dc power converter and a simple and inexpensive control circuit design, that was simulated using the software PSpice, is proposed. The design is based on Lyapunov-Metzler-SPR systems and the performance of the resulting control system is superior to that afforded by a recently proposed alternative sliding-mode control technique. © 2011 IFAC.

Development of an instrumentation system embedded on FPGA for real time measurement of mechanical vibrations in rotating machinery

The real-time monitoring of events in an industrial plant is vital, to monitor the actual conditions of operation of the machinery responsible for the manufacturing process. A predictive maintenance program includes condition monitoring of the rotating machinery, to anticipate possible conditions of failure. To increase the operational reliability it is thus necessary an efficient tool to analyze and monitor the equipments, in real-time, and enabling the detection of e.g. incipient faults in bearings. To fulfill these requirements some innovations have become frequent, namely the inclusion of vibration sensors or stator current sensors. These innovations enable the development of new design methodologies that take into account the ease of future modifications, upgrades, and replacement of the monitored machine, as well as expansion of the monitoring system. This paper presents the development, implementation and testing of an instrument for vibration monitoring, as a possible solution to embed in industrial environment. The digital control system is based on an FPGA, and its configuration with an open hardware design tool is described. Special focus is given to the area of fault detection in rolling bearings. © 2012 IEEE.

Evaluating serial ZigBee devices for application in wireless networked control systems

Networked control systems (NCS) are distributed control system where the sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks (WNCS) enabling interoperability between existing wired and wireless systems. This paper evaluates a serial RS-232 ZigBee device as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the device capabilities. In addition the control performance of an implemented motor control system using the device is analyzed. Experimental results led to the conclusion that serial RS-232 ZigBee devices can be used to implement WNCS and the use of this device delay information in the PID controller discretization can improve the control performance of the system. © 2012 IEEE.

Gesture-based teleoperation using a holonomic robot

This work presents the development and integration of an user interface (UI) framework based on various current input devices that take advantage of our ergonomics. The purpose is to teleoperate a holonomic robot using upper member gestures and postures for studying the suitable of such interfaces when programming and interacting with a mobile robot. As performance vary from UI to UI the framework is focused to be used as a complementary industrial or didactic tool thus, changing how inexperience users tackle their first impressions when working with mobile robots while performing simple gesture-based teleoperation tasks. © 2012 ICROS.

Active vibration control using delayed resonant feedback

Delayed feedback (DF) control is a well-established technique to suppress single frequency vibration of a non-minimum phase system. Modal control is also a well-established technique to control multiple vibration modes of a minimum phase system. In this paper these techniques are combined to simultaneously suppress multiple vibration modes of a non-minimum phase system involving a small time delay. The control approach is called delayed resonant feedback (DRF) where each modal controller consists of a modal filter to extract the target mode signal from the vibration response, and a phase compensator to account for the phase delay of the mode. The methodology is first discussed using a single mode system. A multi-mode system is then studied and experimental results are presented to demonstrate the efficacy of the control approach for two modes of a beam. It is shown that the system behaves as if each mode under control has a dynamic vibration absorber attached to it, even though the actuator and the sensor are not collocated and there is a time delay in the control system. © 2013 IOP Publishing Ltd.

Local data fusion algorithm for fire detection through mobile robot

Multisensor data fusion is a technique that combines the readings of multiple sensors to detect some phenomenon. Data fusion applications are numerous and they can be used in smart buildings, environment monitoring, industry and defense applications. The main goal of multisensor data fusion is to minimize false alarms and maximize the probability of detection based on the detection of multiple sensors. In this paper a local data fusion algorithm based on luminosity, temperature and flame for fire detection is presented. The data fusion approach was embedded in a low cost mobile robot. The prototype test validation has indicated that our approach can detect fire occurrence. Moreover, the low cost project allow the development of robots that could be discarded in their fire detection missions. © 2013 IEEE.

Aplicando lógica fuzzy no controle de robôs móveis usando dispositivos lógicos programáveis e a linguagem VHDL

Pós-graduação em Engenharia Elétrica - FEIS

Controle discreto com modos deslizantes em sistemas incertos com atraso no sinal de controle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Controle de exaustão de fornos de cozimento de anodos baseado em lógica fuzzy

A legislação ambiental cada vez mais rigorosa tem forçado as indústrias a investirem em soluções de controle inovadoras buscando diminuir as emissões de gases poluentes pelas fontes móveis e fixas, exercendo melhor controle e tratamento desses poluentes como forma de atender os limites impostos pela lei. Apresenta-se neste trabalho, a implementação de uma melhoria no sistema de controle de exaustão de fornos de cozimento de anodos da indústria de alumínio ALBRAS-Alumínio Brasileiro S.A., localizada em Barcarena no estado do Pará, visando minimizar a poluição causada pela queima de combustíveis nos fornos sem comprometer a eficiência do processo. Para isso foi utilizado um sistema baseado em lógica fuzzy, buscando na experiência de engenheiros, técnicos e operadores de processo, uma forma de se obter um melhor controle e confiabilidade na gestão das emissões de gases poluentes.

Projeto e construção de um robô móvel AGV/ROV não-holonômico com habilidade para navegação autônoma do tipo wall-following

Esta dissertação de mestrado apresenta o projeto e a construção de um robô móvel terrestre denominado LOGBOT, com tração de movimento do tipo diferencial – com duas rodas motoras e uma roda livre para manter a estabilidade de sua estrutura em relação à superfície. O controle do robô dispõe dos modos de telemetria e autônomo. No modo de controle por telemetria (ROV), a comunicação do robô com a estação de controle é feita por radiofreqüência a uma distância de até um quilometro em ambientes externos, e até cem metros em ambientes internos. No modo de controle autônomo (AGV), o robô tem habilidade para navegar em ambientes internos e desconhecidos usando sempre a parede à sua esquerda como referência para a trajetória de seu movimento. A seqüência de movimentos para execução da trajetória é enviada para a estação de controle que realiza análises de desempenho do robô. Para executar suas tarefas no modo autônomo, a programação do robô conta com um agente inteligente reativo, que detecta características do ambiente (obstáculos, final de paredes, etc.) e decide sobre qual atitude deve ser executada pelo robô, com objetivo de contornar os obstáculos e controlar a velocidade de suas rodas. Os problemas de erro odométrico e suas correções com base no uso de informações sensoriais externas são devidamente tratados. Técnicas de controle hierárquico do robô como um todo e controle em malha fechada da velocidade das rodas do robô são usadas. Os resultados mostraram que o robô móvel LOGBOT é capaz de navegar, com estabilidade e precisão, em ambientes internos no formato de um corredor (wall following).

Desenvolvimento de uma plataforma aberta de robô móvel para propósitos gerais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)