Microbial community composition in fresh water at different stations

Fluorescence in situ hybridization (FISH) with rRNA-targeted oligonucleotide probes was used to investigate the phylogenetic composition of bacterioplankton communities in several freshwater and marine samples. An average of about 50% of the cells were detected by probes for the domains Bacteria and Archaea. Cells were concentrated from water samples (1 to 100 ml) on white polycarbonate filters (diameter, 47 mm; pore size, 0.2 mm; type GTTP 4700 [Millipore, Eschborn, Germany]) by applying a vacuum of <25 kPa. They were subsequently fixed by covering the filter with 3 ml of a freshly prepared, phosphate-buffered saline (pH 7.2)-4% paraformaldehyde (Sigma, Deisenhofen, Germany) solution for 30 min at room temperature. Airdried filters are ready for hybridization and can be stored at 220°C or room temperature for several months without showing apparent changes. Probes BET42a, GAM42a, and PLA886 were used with competitor oligonucleotides as described previously amongst others in Manz et al., (1992; doi:10.1016/S0723-2020(11)80121-9). The filters were transferred to a vial containing 50 ml of prewarmed (48°C) washing solution (70 mM NaCl, 20 mM Tris-HCl [pH 7.4], 5 mM EDTA, 0.01% sodium dodecyl sulfate) and incubated freely floating without shaking at 48°C for 15 min. The filter sections were dried on Whatman 3M paper (Whatman Ltd., Maidstone, United Kingdom) and covered with 50 ml of DAPI solution (1 mg/ml in distilled water filtered through at 0.2-mm filter) for 5 min at room temperature in the dark. For each sample and probe, more than 500 cells were enumerated; for the DAPI examination, more than 1,500 cells were counted per sample. All probe-specific cell counts are presented as the percentage of cells visualized by DAPI. The mean abundances and standard deviations were calculated from the counts of 10 to 20 randomly chosen fields on each filter section. All counts were corrected by subtracting the counts obtained with the negative control NON338. Mean and standard deviation were calculated from the counts of 10 to 20 randomly chosen fields on each filter section.

Grain-size distribution and frictional behaviour of sediment cores from the Nice Slope

The upper shelf of the landslide-prone Ligurian Margin (Western Mediterranean Sea) off Nice well-known for the 1979 Airport Landslide is a natural laboratory to study preconditioning factors and trigger mechanisms for submarine landslides. For this study low-stress ring shear experiments have been carried out on a variety of sediments from >50 gravity cores to characterise the velocity-dependent frictional behaviour. Mean values of the peak coefficient of friction vary from 0.46 for clay-dominated samples (53 % clay, 46 % silt, 1 %) sand up to 0.76 for coarse-grained sediments (26 % clay, 57 % silt, 17 % sand). The majority of the sediments tested show velocity strengthening regardless of the grain size distribution. For clayey sediments the peak and residual cohesive strength increases with increasing normal stress, with values from 1.3 to 10.6 kPa and up to 25 % of all strength supported by cohesive forces in the shallowmost samples. A pseudo-static slope stability analysis reveals that the different lithologies (even clay-rich material with clay content >=50 %) tested are stable up to slope angles <26° under quasi-drained conditions.

Afectación de los agrosistemas de la zona del Caño San Miguel por la salinización de los suelos

La degradación por salinización de los suelos regados con aguas salobres viene aumentando a escala mundial. El problema de la concentración de sales más solubles que el yeso depende principalmente del agua de riego, la aridez climática y la ausencia de drenaje. Estas condiciones se dan en el aluvium del río Limón, que es un tributario del lago Maracaibo, sito en el estado de Zulia de Venezuela. La regulación del río Limón mediante el cierre de los embalses de Manuelote y Tulé ha disminuido los aportes de aguas y sedimentos de las avenidas de inundación, que tienen carácter diluyente. Por otro lado, el balance de sales solubles en el suelo ha registrado una acumulación neta en los años de extrema aridez anteriores al año 2006, dado que la mayor dilución de las aguas ombrogénicas embalsadas procedentes de las lluvias no ha sido suficiente para compensar la concentración por evapotranspiración “in situ” de las aguas retenidas en la cuenca baja, sobre todo en ausencia de desagüe superficial y drenaje profundo. Las inundaciones posteriores a 2006 fueron suficientes para disminuir la salinidad superficial hasta los valores encontrados en 2010. El estudio experimental de esta problemática en el sector del caño San Miguel ha sido abordado mediante el establecimiento del perfil de salinidad acoplado con el perfil hipotético de humedad usado en la taxonomía de suelos. Este perfil define la disponibilidad del agua del suelo para la vegetación en función de tres potenciales: 1) el potencial físico-químico o matricial, que depende de la energía de adsorción a la superficie de las partículas; 2) el potencial gravitatorio, que depende de la profundidad; y 3) el potencial osmótico, que depende de la concentración de la solución del suelo; lo que supone un avance respecto a tener en cuenta sólo el perfil de humedad, que solamente considera el potencial gravi-químico integrado por el matricial y el gravitatorio. El perfil normalizado de 200 mm de de agua útil, retenida entre 33 y 1500 kPa de succión, incluye ocho fases gravi-químicas de 25 mm. La presente investigación incluye el potencial osmótico estimado por la conductividad eléctrica del extracto de pasta saturada. Los experimentos de lavado de sales en columnas de suelo, simulando la distribución de las lluvias en cinco años representativos de los cuartiles estadísticos de la serie disponible de 38 años completos, han determinado el comportamiento de las sales solubles en un suelo sometido a drenaje. Los resultados han evidenciado que el balance de sales unido al balance de agua controla la degradación de los agrosistemas por salinización. La alternativa frutícola puede ser aumentada en estas condiciones, porque el balance de sales favorece el establecimiento de cultivos permanentes a costa de otros usos del suelo de menor interés económico, como el cultivo de forrajes en regadío y el aprovechamiento de los pastizales en secano durante el barbecho de desalinización, cuya caracterización se ha completado con el estudio de la vegetación indicadora del grado de salinidad. ABSTRACT Saline degradation of soils irrigated with brackish water is increasing worldwide. The problem of salts concentration more soluble than gypsum depends on irrigation water quality, climatic aridity, and drainage limitations. These conditions meet in Limón River alluvium, which is tributary to Maracaibo´s Lake in Zulia State, Venezuela. Limón River regulation by closing Manuelote and Tulé reservoirs has diminished the input of water and sediments from inundations, which exerted dilutive effects. On the other hand, the soil balance of soluble salts has registered a net accumulation during those extremely dry years before 2006 because the greater dilution of ombrogenic dammed water coming from rain has not been enough to compensate salt concentration by “in situ” evapotranspiration in middle basin water, mainly in the absence of superficial runoff and deep drainage. Floods after 2006 were enough to reduce the high superficial salinity figures to those addressed in 2010. The experimental study of this trouble in San Miguel´s pipe area has been addressed through of the establishment of its salinity profile together to the hypothetic moisture profile typically used in soil taxonomy. This salinity profile describes soil water availability for vegetation according to three potentials: 1) physico-chemical or matrix potential, which depends on the adsorption energy of the soil solution to the surface of soil particles; 2) gravitational potential, which depends on soil depth; and 3) osmotic potential, which depends on the concentration of the soil solution. This represents an advance from just using moisture regime, which only considers the matrix and gravitational components of a gravi-chemical potential. The standardized moisture profile of 200 mm useful water being retained between 33 and 1500 kPa includes eight gravi-chemical stages of 25 mm. This research also includes the osmotic component, which is estimated by the electric conductivity of the saturated paste extract. Salts leaching trials in soil columns simulating rain distribution along five model years, representing the statistical quartiles of the available series of 38 complete years, have determined the behaviour of soluble salts in a soil being subjected to drainage. Results have evidenced that salt and water balances considered together are able to control the agrosystem’s degradation by salinization. The fruit production alternative could be improved under these conditions because the salts balance favours the establishment of permanent crops to the detriment of other soil uses of lower economical interest such as irrigated forage and non-irrigated pasture during desalinization fallow, which characterization has been completed through assessing the presence of salinity-indicator vegetation.

Characterization of an 241AmBe neutron irradiation facility by different spectrometric techniques

An automated panoramic irradiator with a 3 Ci 241Am-Be neutron source is installed in a bunker-type large room at the Universidad Politécnica de Madrid (UPM). It was recently modified and a neutron spectrometry campaign was organized to characterize the neutron fields in different measurement points along the irradiation bench. Four research groups working with different Bonner Sphere Spectrometers (BSS) and using different spectral unfolding codes took part to this exercise. INFN-LNF used a BSS formed by 9 spheres plus bare detector, with cylindrical, almost point like, 6LiI(Eu) scintillator (4 mm x 4 mm, from Ludlum); UAZ-UPM employed a similar system but with only 6 spheres plus bare detector; UAB worked with a 3He filled proportional counter at 8kPa filling pressure, cylindrical 9 mm x 10 mm (05NH1 from Eurisys) with 11 spheres configuration; and CIEMAT used 12 spheres with an spherical 3He SP9 counter (Centronic Ltd., UK) with very high sensitivity due to the large diameter (3.2 cm) and the filling pressure of the order of 228 kPa. Each group applied a different spectral unfolding method: INFN and UAB worked with FRUIT ver. 3.0 with their own response matrixes; UAZ-UPM used the BUNKIUT unfolding code with the response matrix UTA4 and CIEMAT employed the GRAVEL-MAXED-IQU package with their own response matrix. The paper shows the main results obtained in terms of neutron spectra at fixed distances from the source as well as total neutron fluence rate and ambient dose equivalent rate H*(10) determined from the spectra. The latter are compared with the readings of a common active survey-meter (LB 6411). The small differences in the results of the various groups are discussed.

Tanque aéreo de almacenamiento de gas natural licuado de tipo membrana y 200.000 m3 de volumen

El presente proyecto consiste en el diseño básico de ingeniería de un tanque aéreo de almacenamiento de gas natural licuado (GNL) de integridad total con tecnología de membrana y con una capacidad neta de almacenamiento de 200 000 m3 a una temperatura de -162ºC y una presión máxima de 15 kPa. El proyecto desarrolla los siguientes puntos: el diseño del tanque interno con tecnología de membrana, dimensionamiento del aislante, diseño del techo suspendido, tanque externo, cúpula de hormigón, cimentación, dimensionamiento de los equipos, Ensayos, puesta en frío, puesta en servicio, planificación de la ejecución del proyecto, recursos empleados, control de la presión, prevención del rollover, coste del tanque y análisis económico del proyecto

Aplicación de distintas metodologías a la monitorización de la humedad del suelo y al cálculo del balance hídrico diario

Dada la importancia de conocer la humedad del suelo de forma precisa y en tiempo real, se ha realizado este trabajo de investigación cuyo objetivo principal ha sido seleccionar un Balance Hídrico del Suelo (BHS) diario y validar sus estimaciones de humedad del suelo frente a medidas obtenidas “in situ”, aplicándolo a tres emplazamientos seleccionados en la zona centro con características edáficas y climáticas diferentes, y de este modo estimar con cierta precisión la humedad del suelo como Agua Disponible (AD) para las plantas y a su vez permitir la realización de estudios climáticos. Los observatorios meteorológicos seleccionados fueron: Guadalajara/El Serranillo en la zona aluvial del río Henares; Colmenar Viejo/Base Famet en la rampa sur del Guadarrama sobre rocas metamórficas; y Radiosondeo/Madrid(Barajas) en arenas arcósicas de grano grueso. Se realizó una caracterización morfológica y un estudio de las propiedades físicas, químicas e hidrofísicas de los suelos en cada emplazamiento. El suelo de Guadalajara, Xerorthent Típico presenta una secuencia genética de horizontes (Ap-AC-C1-C2) siendo su clase textural entre franco-arenosa a franca, con menos del 2% de elementos gruesos, presencia de caliza a lo largo de todo el perfil, destacando la homogeneidad en vertical y horizontal de sus propiedades. El suelo de Colmenar, Xerorthent Dystrico, presenta una secuencia genética de horizontes (A-C-C/R) apareciendo el horizonte C/R entre 20-30 cm; y la roca aproximadamente a unos 30 cm; destacando en este perfil su acidez y el alto contenido de elementos gruesos. El suelo de Radiosondeo, Haploxeralf Típico, presenta la secuencia normal de horizontes de los alfisoles (A-Bt1-Bt2-C/Bt); destacando su heterogeneidad principalmente en el plano horizontal, con presencia del Bt a diferentes profundidades en un corto espacio longitudinal. En una primera fase de experimentación (2007-2008) se seleccionaron BHS diarios que sólo utilizaban como datos de entrada la información de variables meteorológicas y el valor del Agua Disponible Total (ADT) para cada tipo de suelo y profundidad. Se probaron BHS diarios con agotamiento exponencial y directo de la reserva, utilizando la evapotranspiración de referencia de Penman-Monteith recomendada por FAO. Al mismo tiempo que se disponía de los datos estimados de humedad de suelo mediante diferentes BHS diarios en los tres emplazamientos, también se realizó una monitorización de la humedad del suelo “in situ” mediante el método gravimétrico, con adaptación de dicha metodología a la problemática de cada suelo, para determinar en cada fecha tanto la humedad del suelo como su contenido de AD para una profundidad de 0 a 30 cm. Se tomaron en cada fecha de muestreo 5 muestras para la profundidad 0- 10 cm, otras cinco para 10-20 cm y otras cinco para 20-30 cm, realizándose el correspondiente tratamiento estadístico de los datos. El ADT se calculó a partir de los datos de capacidad de campo y punto de marchitez obtenidos en laboratorio con membrana de Richards. Los resultados de esta primera fase permitieron conocer que el BHS exponencial diario era el que mejor estimaba el AD en Guadalajara considerando la capacidad de campo a una presión de 33 kPa, mientras que en Colmenar se debían considerar para un mejor ajuste, 10 kPa en lugar de 33 kPa. En el observatorio de Radiosondeo debido a que en cada fecha de muestreo la profundidad en la que aparecía el horizonte Bt era diferente, no se pudo demostrar si el BHS exponencial diario tenía un buen comportamiento. En una segunda fase de experimentación (2009-2012) y con el objeto de aminorar los problemas encontrados en Radiosondeo para la medida de humedad del suelo por el método gravimétrico, se procedió a la instalación y utilización de diferentes sensores de medida de humedad de suelo en el mismo observatorio: TDR (time domain reflectometry - TRIME T3 de IMKO); FDR capacitivo (frecuency domain reflectometry - ECH2O EC-20 de DECAGON) y otros. Esta segunda fase de experimentación tuvo una duración de 4 años y se compararon las medidas de humedad de suelo obtenidas a partir de los sensores con las estimadas del BHS exponencial hasta una profundidad de 0 a 85 cm. En laboratorio se realizaron calibraciones específicas de los sensores TDR y FDR para cada uno de los horizontes más diferenciados del Haploxeralf Típico, utilizando diferentes tipos de regresión. Los valores de humedad de suelo con el equipo TDR, corregidos mediante la calibración específica de laboratorio, fueron los que más se ajustaron a las medidas realizadas por método gravimétrico “in situ”, por lo que se utilizó el TDR para las comparaciones con los valores obtenidos del BHS exponencial diario durante los cuatro años de esta segunda fase experimental. Se realizaron diferentes estimaciones del ADT, partiendo de datos de laboratorio y/o de datos procedentes de humedad de los sensores en campo. Los resultados mostraron de nuevo la conveniencia de utilizar el BHS exponencial diario, pero en este caso, con la estimación del ADT realizada a partir de las gráficas de los sensores. Mediante la utilización de los datos de humedad del BHS exponencial diario se han realizado comparaciones con el mismo tipo de balance pero utilizando un periodo semanal o mensual en lugar de diario, para conocer las diferencias. Los valores obtenidos con periodicidad mensual han dado valores de AD inferiores a los balances calculados semanalmente o diariamente. Por último se ha comprobado que los resultados de un BHS exponencial diario pueden complementar la información que se obtiene del Índice de Precipitación Estandarizado (SPI) y pueden mejorar el estudio de la sequía agrícola. ABSTRACT Due to the importance of a better knowledge of soil water at real time and in a more precisely way, this research work has being carried out with the main objective of selecting a daily Soil Water Balance (SWB) to estimate soil water content, and validate it in comparison to “in situ” measurements. Three locations, differing in soil and climate characteristics, were selected in central Spain in order to estimate with certain acuity soil water as plant-Available Water (AW) and to serve as a tool for the climatic studies. The selected places near meteorology stations were: Guadalajara/El Serranillo an alluvium of the Henares watershed; Colmenar Viejo/Base Famet, in the south raised area of the Guadarrama river basin, over metamorphic rocks; and Radiosondeo/Madrid (Barajas) in coarse arkosic sandstone. Morphology characterization, physical, chemical and hydrologic soil properties were studied in each area. In Guadalajara the soil is a Typic Xerorthent with a (Ap-AC-C1- C2) genetic horizon sequence, loam-sandy to loam textural class, less than 2% of rock fragments, presence of equivalent CaCO3 through the whole profile, outstanding the vertical and horizontal homogeneity of the properties. In Colmenar the soil is represented by a Dystric Xerorthent with a (A-C-C/R) genetic horizon sequence, the C/R is 20-30 cm deep where rock outcrops are approximately at 30 cm; a characteristic feature of this profile is its high acidity and high rock fragments content. In Radiosondeo the soil is represented by a Typic Haploxeralf, with the usual alfisol genetic horizon sequence (A-Bt1-Bt2-C/Bt); outstanding its horizontal heterogeneity, “the variability of the Bt (clay enriched horizon) depth in short distances”. In a first experimental stage (2007-2008), the daily SWB chosen was that which only uses as input data the information from the meteorology variables and plant-Total Available Water (TAW) for each soil type and depth. Different daily SWB (with exponential or direct plant-Available Water depletion) were applied, using the Penman- Monteith reference evapotranspiration (ETo) recommended by FAO. At the same time as soil water content was estimated from the different daily SWB at the three locations, also soil water content was being monitored by “in situ” gravimetric methodology, adapting it to each soil characteristic, to determine every time soil water content and AW to a depth of 0 to 30 cm. In each sampling date, 5 samples for each depth were taken: 0-10 cm; 10-20 cm and 20-30 cm and the data were submitted to the corresponding statistical analysis. The TAW was calculated based on field capacity (FC) and permanent wilting point (PWP) data obtained from laboratory by the Richards pressure plate. Results from this first experimental stage show that the daily exponential SWB was the one which better estimated the AW in Guadalajara considering field capacity at -33 kPa, though in Colmenar, field capacity at -10 kPa must be considered instead of -33 kPa for a better estimation. In Radiosondeo due to the fact that the Bt horizon depth varied in different sampling dates, it could not be established if the daily exponential SWB had a good performance. In a second experimental stage (20019-2012) and with the objective of minimizing the problems encountered in Radiosondeo for measuring “in situ” soil water content by the gravimetric method, the installation of different sensors for measuring soil water content were established and used in the same field location: TDR (time domain reflectometry - TRIME T3 from IMKO), capacitance FDR (frecuency domain reflectometry - ECH2O EC-20 from DECAGON) and others. This second experimental stage lasted 4 years in order to compare the soil water measures from the sensors with the estimations by the exponential SWB form 0 to 85 cm soil depths. At laboratory, specific calibrations for TDR and FDR sensors of the Typic Haploxeralf more differentiated horizons were done using different types of regressions. The results showed that soil water data obtained by the TDR equipment, corrected by the specific laboratory calibration, best fitted to “in situ” gravimetric soil water measures. In this way TDR was used for comparing to the daily exponential SWB during the four years of this second experimentation stage. Various estimations for obtaining TAW were tested; based on laboratory data – and/or on the data obtained of the soil water content field sensors. Results confirmed again, the convenience of using the daily exponential SWB, though in this case, with the TAW obtained from the field sensors graphics. Soil water estimated by exponential SWB on daily basis was compared to weekly and monthly periods, in order to know their reliability. The results obtained for a monthly period gave less AW than the ones obtained in a weekly or daily period. Finally it has been proved that the results obtained from the exponential SWB in a daily bases can be used as a useful tool in order to give complementary information to the SPI (Precipitation Standardized Index) and to help in agricultural drought studies.

Mechanical behaviour and formation process of silkworm silk gut

High performance silk fibers were produced directly from the silk glands of silkworms ("Bombyx mori") following an alternative route to natural spinning. This route is based on a traditional procedure that consists of soaking the silk glands in a vinegar solution and stretching them by hand leading to the so called silkworm guts. Here we present, to the authors’ best knowledge, the first comprehensive study on the formation, properties and microstructure of silkworm gut fibers. Comparison of the tensile properties and microstructural organization of the silkworm guts with those of naturally spun fibers allows gain of a deeper insight into the mechanisms that lead to the formation of the fiber, as well as the relationship between the microstructure and properties of these materials. In this regard, it is proved that an acidic environment and subsequent application of tensile stress in the range of 1000 kPa are sufficient conditions for the formation of a silk fiber.

Biomechanics of the movable pretarsal adhesive organ in ants and bees

Hymenoptera attach to smooth surfaces with a flexible pad, the arolium, between the claws. Here we investigate its movement in Asian weaver ants (Oecophylla smaragdina) and honeybees (Apis mellifera).  When ants run upside down on a smooth surface, the arolium is unfolded and folded back with each step. Its extension is strictly coupled with the retraction of the claws. Experimental pull on the claw-flexor tendon revealed that the claw-flexor muscle not only retracts the claws, but also moves the arolium. The elicited arolium movement comprises (i) about a 90° rotation (extension) mediated by the interaction of the two rigid pretarsal sclerites arcus and manubrium and (ii) a lateral expansion and increase in volume. In severed legs of O. smaragdina ants, an increase in hemolymph pressure of 15 kPa was sufficient to inflate the arolium to its full size. Apart from being actively extended, an arolium in contact also can unfold passively when the leg is subject to a pull toward the body.  We propose a combined mechanical–hydraulic model for arolium movement: (i) the arolium is engaged by the action of the unguitractor, which mechanically extends the arolium; (ii) compression of the arolium gland reservoir pumps liquid into the arolium; (iii) arolia partly in contact with the surface are unfolded passively when the legs are pulled toward the body; and (iv) the arolium deflates and moves back to its default position by elastic recoil of the cuticle.

Oxygen Requirement and Inhibition of C4 Photosynthesis1 : An Analysis of C4 Plants Deficient in the C3 and C4 Cycles

The basis for O2 sensitivity of C4 photosynthesis was evaluated using a C4-cycle-limited mutant of Amaranthus edulis (a phosphoenolpyruvate carboxylase-deficient mutant), and a C3-cycle-limited transformant of Flaveria bidentis (an antisense ribulose-1,5-bisphosphate carboxylase/oxygenase [Rubisco] small subunit transformant). Data obtained with the C4-cycle-limited mutant showed that atmospheric levels of O2 (20 kPa) caused increased inhibition of photosynthesis as a result of higher levels of photorespiration. The optimal O2 partial pressure for photosynthesis was reduced from approximately 5 kPa O2 to 1 to 2 kPa O2, becoming similar to that of C3 plants. Therefore, the higher O2 requirement for optimal C4 photosynthesis is specifically associated with the C4 function. With the Rubisco-limited F. bidentis, there was less inhibition of photosynthesis by supraoptimal levels of O2 than in the wild type. When CO2 fixation by Rubisco is limited, an increase in the CO2 concentration in bundle-sheath cells via the C4 cycle may further reduce the oxygenase activity of Rubisco and decrease the inhibition of photosynthesis by high partial pressures of O2 while increasing CO2 leakage and overcycling of the C4 pathway. These results indicate that in C4 plants the investment in the C3 and C4 cycles must be balanced for maximum efficiency.

Calpain inhibitor AK295 attenuates motor and cognitive deficits following experimental brain injury in the rat.

Marked increases in intracellular calcium may play a role in mediating cellular dysfunction and death following central nervous system trauma, in part through the activation of the calcium-dependent neutral protease calpain. In this study, we evaluated the effect of the calpain inhibitor AK295 [Z-Leu-aminobutyric acid-CONH(CH2)3-morpholine] on cognitive and motor deficits following lateral fluid percussion brain injury in rats. Before injury, male Sprague-Dawley rats (350-425 g) were trained to perform a beam-walking task and to learn a cognitive test using a Morris water maze paradigm. Animals were subjected to fluid percussion injury (2.2-2.4 atm; 1 atm = 101.3 kPa) and, beginning at 15 min postinjury, received a continuous intraarterial infusion of AK295 (120-140 mg/kg, n = 15) or vehicle (n= 16) for 48 hr. Sham (uninjured) animals received either drug (n = 5) or vehicle (n = 10). Animals were evaluated for neurobehavioral motor function at 48 hr and 7 days postinjury and were tested in the Morris water maze to evaluate memory retention at 7 days postinjury. At 48 hr, both vehicle- and AK295-treated injured animals showed significant neuromotor deficits (P< 0.005). At 7 days, injured animals that received vehicle continued to exhibit significant motor dysfunction (P< 0.01). However, brain-injured, AK295-treated animals showed markedly improved motor scores (P<0.02), which were not significantly different from sham (uninjured) animals. Vehicle-treated, injured animals demonstrated a profound cognitive deficit (P< 0.001), which was significantly attenuated by AK295 treatment (P< 0.05). To our knowledge, this study is the first to use a calpain inhibitor following brain trauma and suggests that calpain plays a role in the posttraumatic events underlying memory and neuromotor dysfunction.

Compressibility as a means to detect and characterize globular protein states.

We report compressibility data on single-domain, globular proteins which suggest a general relationship between protein conformational transitions and delta kzeroS, the change in the partial specific adiabatic compressibility which accompanies the transition. Specifically, we find transitions between native and compact intermediate states to be accompanied by small increases in kzeroS of +(1-4) x 10(-6) cm3.g-1.bar-1 (1 bar = 100 kPa). By contrast, transitions between native and partially unfolded states are accompanied by small decreases in kzeroS of -(3-7) x 10(-6) cm3.g-1.bar-1, while native-to-fully unfolded transitions result in large decreases in kzeroS of -(18-20) x 10(-6) cm3.g-1.bar-1. Thus, for the single-domain, globular proteins studied here, changes in kzeroS correlate with the type of transition being monitored, independent of the specific protein. Consequently, kzeroS measurements may provide a convenient approach for detecting the existence of and for defining the nature of protein transitions, while also characterizing the hydration properties of individual protein states.

Reaproveitamento de meio de cultivo de Arthrospira platensis tratado por processos de microfiltração e ultrafiltração

Micro-organismos fotossintetizantes, incluído aqui o gênero Arthrospira, vêm sendo amplamente produzidos em larga escala em vários países, detendo um mercado que gera mais de 1 bilhão de dólares ao ano. A produção industrial utiliza grande volume de água com alta concentração salina para produzir milhares de toneladas de biomassa microalgal. É crescente a utilização de tratamento de águas por processo de separação por membranas, demonstrando ser uma técnica que gera água de ótima qualidade, de instalação compacta e de fácil automação. No presente trabalho, foi avaliada esta tecnologia para o reaproveitamento do meio de cultura em novos cultivos de micro-organismos fotossintetizantes, visando contribuir para a sustentabilidade deste processo produtivo. O efluente do cultivo de Arthrospira platensis oriundo de processo descontínuo em minitanques foi submetido a tratamento por membranas de filtração tangencial, incluindo microfiltração (MF) (porosidades de 0,65 µm e de 0,22 µm) e ultrafiltração (UF) (peso molecular de corte de 5.000 Da), em pressões transmembrana (TMP) de 22,5 a 90 kPa. Os processos de MF levaram a reduções médias de 53,9±1,3 % e 93,1±1,1 % de matéria orgânica natural (NOM) e pigmentos nos meios residuais, respectivamente. Com o uso de processos de UF, cujos meios foram previamente tratados por MF (0,22 µm e 22,5 kPa), as reduções médias de NOM e pigmentos foram de 57,2±0,5 % e 94,0±0,8 %, respectivamente. Os processos de MF com TMP de 22,5 kPa levaram a concentrações celulares máximas (Xm) equivalentes às obtidas com meio novo. O uso de membrana de 0,65 µm e TMP de 22,5 kPa levou a uma perda média de 2,9 %, 22,7 % e 16,4% dos nutrientes carbonato, fosfato e nitrato, respectivamente, mas a correção desses valores aos mesmos do meio padrão levou à obtenção dos mais altos valores de Xm (3586,6±80 mg L-1), produtividade em células (505,0±11,6 mg L-1 d-1) e fator de conversão de nitrogênio em células (29,6±0,7 mg mg-1). O teor protéico da biomassa foi estatisticamente igual ao da biomassa obtida de cultivo com meio padrão novo. Os dados deste trabalho evidenciam que processos de filtração por membrana são promissores para o reuso de meio de micro-organismos fotossintetizantes.

A Transdiagnostic Social Skills Intervention; Using a Structured Story to Teach Children How to Ask a Friend to Play

An (independent samples comparison) controlled study was conducted to assess the efficacy of a novel approach to social skills training for children in a local socialization group at Knippenberg, Patterson & Associates (KPA). The treatment condition involved the combination of a Structured Story (i.e., novel bibliotherapy technique for children with social skills deficits), and a behavioral rehearsal (or role-play) segment, where the children practiced the target social skill featured in the Structure Story. The control group did not receive the Structured Story nor the behavioral rehearsal. Children in both groups engaged in ten-minutes of free play that was videorecorded for later observation and scoring by the principal investigator. Two target behaviors were assessed; asking a friend to play, and duration of joint play between two or more peers. The results did not show significant differences for either target variable between the group that received the novel intervention and the control group. Limitations of the current study and implications for further research are discussed.

Propriedades físico-químicas e mecânicas de membranas porosas de carboximetilquitosana e hidrogéis de quitosana para aplicação em engenharia de tecidos

Este trabalho teve como principal objetivo produzir membranas porosas de carboximetilquitosana e hidrogéis de quitosana com propriedades físico-químicas e mecânicas adequadas para aplicações em Engenharia de Tecidos. Para isso, quitosanas com diferentes graus de acetilação (4,0%<GA<40%) e de elevada massa molar média viscosimétrica (Mv>750.000 g.mol-1) foram produzidas através da aplicação de processos consecutivos de desacetilação assistida por irradiação de ultrassom de alta intensidade (DAIUS) à beta-quitina extraída de gládios de lulas Doryteuthis spp. A carboximetilação de quitosana extensivamente desacetilada (Qs-3; GA=4%) foi realizada pela reação com ácido monocloroacético em meio isopropanol/solução aquosa de NaOH, gerando a amostra CMQs-0 (GS≈0,98; Mv≈190.000 g.mol-1). A irradiação de ultrassom de alta intensidade foi empregada para tratar solução aquosa de CMQs-0 durante 1 h e 3 h, resultando nas amostras CMQs-1 (Mv≈94.000 g.mol-1) e CMQs-3 (Mv≈43.000 g.mol-1), respectivamente. Para a produção de membranas reticuladas, genipina foi adicionada em diferentes concentrações (1,0x10-4 mol.L-1, 3,0x10-4 mol.L-1 ou 5,0x10-4 mol.L-1) às soluções aquosas das CMQs, que foram vertidas em placas de Petri e a reação de reticulação procedeu por 24 h. Em seguida, as membranas reticuladas (M-CMQs) foram liofilizadas, neutralizadas, lavadas e liofilizadas novamente, resultando em nove amostras, que foram caracterizadas quanto ao grau médio de reticulação (GR), grau médio de hidratação (GH), morfologia, propriedades mecânicas e quanto à susceptibilidade à degradação por lisozima. O grau médio de reticulação (GR) foi tanto maior quanto maior a concentração de genipina empregada na reação, variando de GR≈3,3% (M-CMQs-01) a GR≈17,8% (M-CMQs-35). As análises de MEV revelaram que as membranas reticuladas M-CMQs são estruturas porosas que apresentam maior densidade de poros aparentes quanto maiores os valores de Mve GR. Entretanto, as membranas preparadas a partir de CMQs de elevada massa molar (Mv>94.000 g.mol-1) e pouco reticuladas (GR<10%), apresentaram propriedades mecânicas superiores em termos de resistência máxima à tração (>170 kPa) e elongação máxima à ruptura (>40%). Por outro lado, as membranas mais susceptíveis à degradação enzimática foram aquelas preparadas a partir de CMQs de baixa massa molar (Mv≈43.000 g.mol-1) e que exibiram baixos graus de reticulação (GR<11%). Hidrogéis estáveis de quitosana sem o uso de qualquer agente de reticulação externo foram produzidos a partir da gelificação de soluções aquosas de quitosana com solução de NaOH ou vapor de NH3. Os hidrogéis produzidos a partir de soluções de quitosana de elevada massa molar média ponderal (Mw≈640.000 g.mol-1) e extensivamente desacetilada (DA≈2,8%) em concentrações poliméricas acima 2,0%, exibiram melhores propriedades mecânicas com o aumento da concentração polimérica, devido à formação de numerosos emaranhamentos físicos das cadeias poliméricas em solução. Os resultados mostram que as propriedades físico-químicas e mecânicas dos hidrogéis de quitosana podem ser controladas variando a concentração do polímero e o processo de gelificação. A avaliação biológica de tais hidrogéis para a regeneração de miocárdio infartado de ratos revelou que os hidrogéis de quitosana preparados a partir de soluções de polímero a 1,5% foram perfeitamente incorporados sobre a superfície do epicárdio do coração e apresentaram degradação parcial acompanhada por infiltração de células mononucleares.

Influência do tamanho da amostra na determinação da curva de retenção da água no solo

A curva de retenção da água no solo é um dos principais instrumentos para avaliar a qualidade física dos solos e possibilitar seu manejo adequado. Por meio da Teoria da Capilaridade vários equipamentos foram desenvolvidos para determinar a intensidade com que a água está retida ao solo, porém, pouco se tem dado atenção para verificar se os pressupostos para o real funcionamento da teoria estão sendo atendidos. Um aspecto refere-se ao tamanho da amostra utilizada para determinar a curva de retenção, de modo que haja continuidade dos feixes capilares na amostra e placa porosa. Desta forma, este trabalho propõe avaliar diferentes tamanhos de amostra indeformada para a determinação da curva de retenção. Para isso, coletaram-se amostras em anéis volumétricos cilíndricos de três tamanhos (altura) diferentes (T1 - 0,075 m; T2 - 0,05 m; T3 - 0,025 m;) e mesmo diâmetro interno (0,07 m), dos horizontes diagnósticos de um Latossolo e um Nitossolo em áreas experimentais da Escola Superior de Agricultura Luiz de Queiroz (Esalq/USP), Piracicaba - SP. Realizou-se a caracterização física destes solos, por meio da análise granulométrica, densidade do solo, densidade de partículas, porosidade total e teor de carbono orgânico. As curvas foram determinadas para cada tamanho de amostra, utilizando-se o Funil de Haines, para as tensões 0,5, 1, 4, 6 e 10 kPa, e a Câmara de Pressão de Richards para 33, 100 e 500 kPa. As curvas de retenção foram ajustadas pelo modelo utilizado por van Genuchten. Estimadas as curvas, avaliou-se a distribuição de poros do solo das amostras, determinando-se a curva de frequência acumulada de poros em função do logaritmo do raio e, depois pela diferenciação das equações de ajuste das curvas de retenção, a curva diferencial de frequência acumulada de poros. Os resultados mostram que o Latossolo, por ter textura arenosa no horizonte estudado, não apresentou diferença significativa nas curvas de retenção para os tamanhos das amostras estudadas. Verificou-se pouca modificação na distribuição dos poros deste solo, que possui teor elevado das frações areia fina e muito fina, e desenvolveram papel importante para a retenção de água. O Nitossolo, por sua vez, apresentou diferença significativa da curva obtida pela amostra de menor tamanho (T3), havendo maior retenção de água com a diminuição do tamanho da amostra. Devido a sua textura muito argilosa, o arranjo estrutural deste solo foi diferenciado ao se utilizar as amostras maiores, com provável interrupção e descontinuidade dos feixes capilares. Consequentemente, houve também alteração na distribuição dos poros, com redução dos mesoporos e aumento dos microporos. Desta forma, pode-se concluir que o tamanho da amostra influenciou a curva de retenção da água devido à complexidade estrutural do solo, que provavelmente é diferente nas amostras maiores por causa da continuidade dos feixes capilares, principalmente no Nitossolo. Em outras palavras, quanto menor o tamanho da amostra há menor diferenciação no arranjo de poros, ou seja, maior proximidade da real condição do solo e, assim, uma interpretação da retenção de água \"mais correta\" por meio da Teoria da Capilaridade.