Radial displacement of a fluid annulus in a rotating Hele-Shaw cell

The radial displacement of a fluid annulus in a rotating circular HeleShaw cell has been investigated experimentally. It has been found that the flow depends sensitively on the wetting conditions at the outer interface. Displacements in a prewet cell are well described by Darcy"s law in a wide range of experimental parameters, with little influence of capillary effects. In a dry cell, however, a more careful analysis of the interfacemotion is required; the interplay between a gradual loss of fluid at the inner interface, and the dependence of capillary forces at the outer interface on interfacial velocity and dynamic contact angle, result in a constant velocity for the interfaces. The experimental results in this case correlate in the form of an empirical scaling relation between the capillary number Ca and a dimensionless group, related to the ratio of centrifugal to capillary forces, which spans about three orders of magnitude in both quantities. Finally, the relative thickness of the coating film left by the inner interface is obtained as a function of Ca.

Nestepakkauskartongin kosteuden hallinta

Koska kartonki on hygroskooppista, sen kosteus on riippuvainen ilman lämpötilasta ja suhteellisesta kosteudesta. Liian korkea kosteus kartongissa aiheuttaa jäykkyyden alenemista, kartongin sitkeyttä, sekä pullistuneita pakkauksia kuluttajilla. Kosteusongelmia syntyy varastoinnissa, sekä kylmän rullan käsittelyn aikana lämpimissä tuotantotiloissa. Rullaa tulisi säilyttää tiiviissä paketissa, jotta se olisi suojattu ympäristön vaihtelevilta olosuhteilta. Jos pakkaus ei ole tiivis ja ympäröivä ilma pääsee kontaktiin kartongin kanssa kylmävarastoinnin aikana, nousee kartongin kosteus jo parissa vuorokaudessa yli 7 %:iin ilman lämpötilan ollessa 15 °C ja suhteellisen kosteuden 95 %. Kirjallisuusosan tavoitteena oli kartoittaa tekijät, joilla on vaikutusta kuitujen ominaisuuteen imeä itseensä kosteutta ympäröivästä ilmasta. Kokeellisessa osassa selvitettiin, oliko kartongin kosteuden nousu johtunut tasapainokosteuden nousemisesta. Painopisteenä oli tutkia kosteuden muutokset varastoinnin ja konvertoinnin sekä pakkaustuotteen käytön aikana. Simuloinnin avulla määritettiin kosteuden penetroituminen rullaan. Tutkittiin pakkausmateriaalien vesihöyrytiiveydet ja käärinnän vaikutus rullapakkauksen sisäisiin olosuhteisiin. Nestepakkauskartongin tasapainokosteus ei ollut muuttunut. Käytännön varastointikokeiden avulla havaittiin, että pinon päällimmäinen rulla altistui eniten ympäröivän ilman olosuhteiden muutoksille. Havaittiin myös kosteuseroa tämän rullan reunojen välillä. Mitä lyhyempi on varastointiaika kartongin päällystyksen jälkeen, sitä paremmin ehkäistään kosteuden noususta aiheutuvat haitat kartongissa. Maksimivarastointiaika rullille on 1,5 kuukautta, jolloin kartongin kosteus oli 6,5 % ja pinon päällimmäisessä rullassa noin 6,7 %. Pitkään varastoidusta kartongista valmistetuissa maitotölkeissä oli korkein kosteus, suurin pullistuma ja alhaisin otejäykkyys 10 päivän jälkeen täytöstä. Varastointiajan ollessa pitkä, kartongista tulee sitkeää ja venyvää, ja se sitoo enemmän kosteutta kuin mitä se on sitonut ennen varastoon tuloa. Skaivaus pienentää kosteuspenetraatiota raakakartonkiin, jolloin jäykkyys säilyy ja pullistuma pienenee pakkauksessa.

PEC1/AtABCG32 transport function in cuticle biosynthesis

Most aerial parts of the plants are covered by a hydrophobic coating called cuticle. The cuticle is formed of cutin, a complex mixture of esterified fatty acids that are embedded and associated with waxes. The cuticle often appears as a superposition of layers of different composition: The cuticle proper formed of cutin and a mixture of waxes and underneath, the cuticle layer containing cutin, intracuticular waxes and polysaccharides of the cell wall. In addition to its involvement in plant development by preventing organ fusions, the cuticle acts as a barrier to prevent water loss and protect plants against environmental aggressions such as excessive radiation or pathogens attacks. PEC1/AtABCG32 is an ABC transporter from the PDR family involved in cutin biosynthesis. Characterization of the peci mutant in Arabidopsis thaliana showed that PEC1 plays a significant role in the diffusion barrier formation in leaves and petals. The cuticles of leaves and flowers of peci are permeable and the cuticular layer rather than the cuticular proper was altered in the petals, underlining the importance of this particular layer in the maintenance of the diffusion barrier. Chemical analysis on the flower cutin monomer composition of ped mutant revealed a decrease in hydroxylated cutin monomers, suggesting a function of PEC1 in the incorporation of these monomers in the polymer cutin. However, the exact nature of the substrates of PEC1 remained elusive. PEC1 homologues in barley and rice, respectively HvABCG31/EIBI1 and OsABCG31, are also implicated in cuticle biosynthesis. Interestingly, the rice mutant displays more severe phenotypes such as dwarfism and spreading necrosis conducting to the seedling death. In this work, we further characterized osabcg31 mutant and hairpin-RNAi downregulated OsABCG31 plant lines showing reduced growth and cuticle permeability. Our analysis showed a decrease in hydroxylated cutin monomers and severe disruptions in the cuticle, which explain the permeability. Further insights into the function of the cuticle in rice resistance/susceptibility to Pathogens were obtained after inoculation with Magnaporthe oryzae, the fungus responsible for the rice blast disease. Osabcg31 as well as the transgenic lines downregulating OsABCG31 showed increased resistance to the fungus. However, only later steps of infection are reduced . and no impact is obseived on the germination or penetration stages, suggesting that the cuticle disruption per se is not responsible for the resistance. We further investigated the cause of the resistance by analyzing the expression of defense related gene in osabcg31 prior to infection. We found that osabcg31 constitutively express defense related genes, which may explain the resistance, the dwarfism and the cell death. osabcg31 is thus a tool to study the connection between cuticle, plant development and defense signaling networks in rice. The transport function of PEC1 family members is still unknown. In order to link cutin biosynthesis and transport activity, we combined ped mutation with mutations in cutin synthesis related genes. Here, we show that PEC1 acts independently from GPAT4 and GPAT8 pathway and partially overlaps with GPAT6 biosynthesis pathway that leads to the production of hydroxylated C16 cutin precursor 2-Mono(10,16-dihydroxyhexadecanoylJglycerol (2-MHG). In addition, we noticed that despite a comparable cutin monomer composition, ped mutant leaves cuticle are permeable while that of gpat6 mutant are not. This finding raises the possibility of PEC1 being required for the incorporation of C16 hydroxylated monomers and their structural arrangement rather than their direct transport towards the cuticle. A careful investigation of the cuticle permeability, cutin composition and ultrastructure during leave development in Wt plants and ped mutants revealed a possible different regulation of several pathways of cutin biosynthesis and showed the importance of PEC1 function early during leave cuticle maturation. In order to elucidate the transport activity of PEC1, we successfully expressed PEC1 in Nicotiana benthamiana plant system for direct transport experiments. This system will be used to test the PEC 1-dependent transport of potential substrates such as sn-2-monoacylglycerol loaded with a hydroxylated C16 fatty acid. -- Toutes les parties aériennes des plantes sont recouvertes d'une couche hydrophobe appelée «cuticule». Cette cuticule est composée de cutine, un polymère d'acides gras estérifiés, et de cires. La cuticule apparaît souvent sous forme de couches superposées: une première couche extérieure appelée «cuticle proper» formée de cutine et d'un mélange de cires, et une deuxième couche, la «cuticle layer», formée de cutine associée à des cires intracuticulaires et des polysaccharides pariétaux. La cuticule joue le rôle de barrière prévenant contre la perte d'eau et les agressions environnementales. AtABCG32/PEC1 est un transporteur ABC de la famille des PDR impliqué dans la synthèse de la cutine. L'étude du mutant peci d'Arabidopsis thaliana a révélé une fonction de PEC1 dans la formation de la barrière de diffusion. La cuticule des feuilles et fleurs de peci est perméable. Des altérations de la «cuticle layer» ont été démontrées, soulignant son importance dans le maintien de la barrière. L'analyse de la composition de la cutine de peci a montré une réduction spécifique en monomères hydroxylés, suggérant un rôle de PEC1 dans leur incorporation dans la cuticule. Cependant, la nature exacte des substrats de PEC1 n'a pas été identifiée. PEC1 possède deux homologues chez l'orge et le riz, respectivement HvABCG31 et OsABCG31, et qui sont impliqués dans la biosynthèse de la cuticule. Chez le riz, des phénotypes plus sévères ont été observés tels que nanisme et nécroses conduisant à la mort des jeunes plants. Dans cette étude, nous avons continué la caractérisation de osabcg31 ainsi que des lignées de riz sous exprimant le gène OsABCG31 et présentant une cuticule perméable tout en ayant une meilleure croissance. Notre étude a démontré une réduction des monomères hydroxylés de cutine et une désorganisation de la structure de la cuticule, aggravée dans le mutant osabcg31. Ce résultat explique la perméabilité observée. Des mformations P|us approfondies sur l'implication de la cuticule dans la résistance aux pathogènes ont été obtenues après inoculation du mutant osabcg31 et les lignées sous- exprimant OsABCG31 avec une souche virulente de Magnaporthe Oryzae, le champignon responsable de la pyriculariose du riz. Les différentes lignées testées ont démontré une résistance au pathogène. Cependant, seules les étapes tardives de l'infection sont réduites et aucun impact n'est observé sur la germination des spores ou la pénétration du champignon, suggérant que les modifications de la cuticule ne sont pas directement à l'origine de la résistance. L'analyse de l'expression de gènes impliqués dans la résistance à Magnaporthe.oryzae a mis en évidence l'expression constitutive de ces gènes en l'absence de tout contact avec le pathogène. Ceci explique la résistance, le nanisme et la mort cellulaire observés. Ainsi, osabcg31 représente un outil efficace pour l'étude intégrée des systèmes de régulation de la défense, de développement des plantes et la cuticule. La nature des substrats transportés par PEC1/AtABCG32 reste inconnue. Dans le but d'établir une liaison entre biosynthèse de cutine et transport des précurseurs par PEC1, la mutation peci a été combinée avec des mutants impliqués dans différentes voies de biosynthèse. Cette étude a démontré une fonction indépendante de PEC1 de la voie de biosynthèse impliquant les enzymes GPAT4 et GPAT8, et une fonction partiellement indépendante de la voie impliquant GPAT6 qui mène à la production de précurseurs sn-2- monoacylglycerol chargés en acides gras en C16 (2-MHG). De plus, malgré un profil similaire en monomères de cutine, gpat6 conserve une cuticule imperméable alors que celle de PEC1 est perméable. Ceci suggère que PEC1 est nécessaire à l'incorporation des monomères en C16 et leur arrangement structurel plutôt que simplement à leur transport direct. L'étude approfondie de la perméabilité cuticulaire, de la structure ainsi que de la composition en cutine pendant le développement des feuilles de peci et la plante sauvage a révélé l'existence de différentes régulations des voies de biosynthèses des monomères et a démontré l'importance de PEC1 dans les premières étapes de la mise en place de la cuticule. Pour identifier les substrats transportés, l'expression de PEC1 chez le système hétérologue Nicotiana benthamiana a été conduite avec succès. Ce système sera utilisé pour tester le transport de substrats potentiels tels que le sn-2-monoacylglycerol chargé en acide gras en C16.

Eletrodos quimicamente modificados aplicados à eletroanálise: uma breve abordagem

Chemically modified electrodes (CMEs) have been subject of considerable attention since its inception about 23 years ago. CMEs result of a deliberate immobilization of a modifier agent onto the electrode surface obtained through chemical reactions, chemisorption, composite formation or polymer coating. This immobilization seeks transfer the physicochemical properties of the modifier to the electrode surface and thus to dictate and control the behavior of the electrode/solution interface. In recent years the interest in CMEs has increased particularly to enhance the sensitivity and/or the selectivity of electroanalytical techniques. In general higher sensitivity and/or selectivity may be achieved by exploiting one or more of the following phenomena: electrocatalysis, preconcentration and interferents exclusion. This paper deals with the application of CMEs in electroanalysis, including a brief presentation of the more general procedures that have been employed for the modification of electrode surfaces.

Caracterização de filmes finos de Nb2O5 com propriedades eletrocrômicas

The sols for thin electrochromic coatings of Nb2O5 were obtained by synthesis of the niobium butoxide from BuONa and NbCl5. The ~300nm thick films were deposited by dip-coating technique from the alkoxide solution and calcined at 560ºC in O2 atmosphere during 3 hours. The particles size of niobium oxide (V) powder (~20mm) was obtained from x-ray diffraction using the Scherrer equation. The coatings were characterized by cyclic voltammetry and cronoamperommetry techniques. The spectral variation of the optical transmittance were determined in situ as a function of the cyclical potencial and memory effect. The insertion process of lithium is reversible and change the film color from transparent (T=80%) to dark blue (T=20%).

Coatings on Composites

Polymer based composite materials coated with thin layers of wear resistant materials have been proposed as replacements for steel components for certain applications with the advantage of reduced mass. Magnetron sputtered coatings can be successfully deposited on composite materials. Nevertheless there are number of issues which must be addressed such as limited temperature, which the composite can withstand because of the epoxy binder which is used, the adhesion of the coating to the composite and the limited mechanical support, the hard coating can obtain from the relatively soft epoxy. We have investigated the deposition of chromium nitride, titanium carbide and titanium doped DLC coatings on carbon fibre reinforced composites and various polymers. The adhesion of the coatings has been studied by the pull-off adhesion tester. In general, the failure mechanism has been noticed to be due to the cohesive failure for a wide range of conditions. The wear behavior of the coatings has been noticed to be complicated. Wear tests on coated composites have shown that where the reinforcing fibres are near the surface, the composite samples do not perform well due to breakage of the fibres from the polymer matrix. A fibre free surface has been noticed to improve the wear resistance.

Characterisation of pigment particles by scanning electron microscope and image analysis programs

Coating and filler pigments have strong influence to the properties of the paper. Filler content can be even over 30 % and pigment content in coating is about 85-95 weight percent. The physical and chemical properties of the pigments are different and the knowledge of these properties is important for optimising of optical and printing properties of the paper. The size and shape of pigment particles can be measured by different analysers which can be based on sedimentation, laser diffraction, changes in electric field etc. In this master's thesis was researched particle properties especially by scanning electron microscope (SEM) and image analysis programs. Research included nine pigments with different particle size and shape. Pigments were analysed by two image analysis programs (INCA Feature and Poikki), Coulter LS230 (laser diffraction) and SediGraph 5100 (sedimentation). The results were compared to perceive the effect of particle shape to the performance of the analysers. Only image analysis programs gave parameters of the particle shape. One part of research was also the sample preparation for SEM. Individual particles should be separated and distinct in ideal sample. Analysing methods gave different results but results from image analysis programs corresponded even to sedimentation or to laser diffraction depending on the particle shape. Detailed analysis of the particle shape required high magnification in SEM, but measured parameters described very well the shape of the particles. Large particles (ecd~1 µm) could be used also in 3D-modelling which enabled the measurement of the thickness of the particles. Scanning electron microscope and image analysis programs were effective and multifunctional tools for particle analyses. Development and experience will devise the usability of analysing method in routine use.

LWC-paperin opasiteetin parantaminen

LWC-syväpainopaperilta vaaditaan hyvän ajettavuuden, kiillon ja sileyden ohella hyvää opasiteettia. Tämä on asettanut haasteita LWC-paperin valmistajille paperin neliömassojen laskiessa. Tässä diplomityössä etsittiin keinoja parantaa kevyiden LWC-syväpainolajien opasiteettia heikentämättä oleellisesti muita tärkeitä paperin ominaisuuksia. Tavoitteena oli nostaa CR48-lajin opasiteetti tavoitearvoon 90 %. Työn kirjallisuusosassa perehdyttiin paperin optisten ominaisuuksien teoriaan sekä raaka-aineisiin ja prosessin osiin, joilla on vaikutusta paperin opasiteettiin. Työn kokeellisessa osassa tutkittiin olemassa olevan aineiston perusteella tekijöitä, joilla uskottiin olevan vaikutusta CR48-lajin opasiteettiin. Tutkimuksen ja kirjallisuuden perusteella ajettiin tehdaskoeajoa, joiden avulla pyrittiin parantamaan paperin opasiteettia. CR48-lajin opasiteettitavoite saavutettiin kolmella eri tavalla. Opasiteettitavoite saavutettiin, kun paperin vaaleus säädettiin tavoitearvoon pigmenttivärin avulla tumman hierteen sijasta. Tällöin väripigmentin määrää päällystyspastassa nostettiin 0,01 osaa ja valkaistun hierteen osuus kokonaishierteen määrästä oli 100 %. Vaaleuden säätö pastavärillä oli käytännössä hidasta ja hankalaa. Opasiteettitavoite saavutettiin myös, kun hierre jauhettiin täysin koeterillä. Koeterillä tapahtuva jauhatus oli rajumpaa ja katkovampaa kuin perinteisillä terillä, joten hienoaineen lisääntyminen ja kuidun lyheneminen paransivat paperin opasiteettia, mutta lujuudet huononivat. Lisäksi tavoiteopasiteetti saavutettiin, kun sellun osuutta vähennettiin 8 %-yksikköä. Lujuuden säilymisen kannalta sellun vähennys oli parempi keino opasiteetin parantamiseksi kuin hierteen jauhaminen koeterillä. Koeajojen perusteella pohjapaperin tuhkapitoisuuden nostolla ja hierteen CSF-luvun alentamisella ei ollut vaikutusta paperin opasiteettiin. Lisäksi 100 %:nen koeterillä jauhettu sahahakehierre antoi paperille huonomman opasiteetin kuin hierre, josta puolet oli jauhettu koeterillä ja raaka-aineesta 25 % oli sahahaketta.

Dióxido de titânio sol-gel: propriedades e comportamento eletrocrômico

Titanium dioxide was prepared by hydrolysis and polycondensation of titanium tetraisopropoxide. TiO2 films were obtained by spin coating of the precursor solution on ITO substractes (glass covered with indium doped tin oxide). Films were prepared using different temperatures and hydrochloric acid contents. The effect of the drying temperature of the films (100 or 400ºC) was also investigated. TiO2 films were characterized by cyclic voltammetry, chronoamperometry, ultraviolete-visible spectroscopy, scanning electron microscopy and X-ray diffractrometry.

Eletrodos modificados com polímeros perfluorados e sulfonados: aplicações em análises ambientais

Perfluoro and sulfonated ion-exchange polymers are recognized as a very useful material for various mechanistic studies and applications in electrochemistry. These polymers are characterized by high equivalent weights and by a low number of ion-exchange sites interposed between long organic chains. The solubility enables a preparation of stable polyelectrolyte films on the electrode surface. Examples of the determination of trace metals and organic componds in real environmental samples are presented.

Nanoparticle Labels in Bioaffinity Assays

Nanoparticles offer adjustable and expandable reactive surface area compared to the more traditional solid phase forms utilized in bioaffinity assays due to the high surface to-volume ratio. The versatility of nanoparticles is further improved by the ability to incorporate various molecular complexes such as luminophores into the core. Nanoparticle labels composed of polystyrene, silica, inorganic crystals doped with high number of luminophores, preferably lanthanide(III) complexes, are employed in bioaffinity assays. Other label species such as semiconductor crystals (quantum dots) or colloidal gold clusters are also utilized. The surface derivatization of such particles with biomolecules is crucial for the applicability to bioaffinity assays. The effectiveness of a coating is reliant on the biomolecule and particle surface characteristics and the selected coupling technique. The most critical aspects of the particle labels in bioaffinity assays are their size-dependent features. For polystyrene, silica and inorganic phosphor particles, these include the kinetics, specific activity and colloidal stability. For quantum dots and gold colloids, the spectral properties are also dependent on particle size. This study reports the utilization of europium(III)-chelate-embedded nanoparticle labels in the development of bioaffinity assays. The experimental covers both the heterogeneous and homogeneous assay formats elucidating the wide applicability of the nanoparticles. It was revealed that the employment of europium(III) nanoparticles in heterogeneous assays for viral antigens, adenovirus hexon and hepatitis B surface antigen (HBsAg), resulted in sensitivity improvement of 10-1000 fold compared to the reference methods. This improvement was attributed to the extreme specific activity and enhanced monovalent affinity of the nanoparticles conjugates. The applicability of europium(III)-chelate-doped nanoparticles to homogeneous assay formats were proved in two completely different experimental settings; assays based on immunological recognition or proteolytic activity. It was shown that in addition to small molecule acceptors, particulate acceptors may also be employed due to the high specific activity of the particles promoting proximity-induced reabsorptive energy transfer in addition to non-radiative energy transfer. The principle of proteolytic activity assay relied on a novel dual-step FRET concept, wherein the streptavidin-derivatized europium(III)-chelate-doped nanoparticles were used as donors for peptide substrates modified with biotin and terminal europium emission compliant primary acceptor and a secondary quencher acceptor. The recorded sensitized emission was proportional to the enzyme activity, and the assay response to various inhibitor doses was in agreement with those found in literature showing the feasibility of the technique. Experiments regarding the impact of donor particle size on the extent of direct donor fluorescence and reabsorptive excitation interference in a FRET-based application was conducted with differently sized europium(III)-chelate-doped nanoparticles. It was shown that the size effect was minimal

Highly functional binding surface for miniaturised solid-phase immunoassays. - A spot story -

Several bioaffinity assays are based on the detection of an analyte which is bound on a solid substrate via biochemical interaction. These so called solid phase assays are based on the adhesion of the primary binding partner on a solid surface, which then binds the analyte to be detected. In this thesis work a novel solid phase based assay technology, known as spot technology, was developed. The spot technology is based on combination of high-capacity solid phases, concentrated in a spot format, utilising modified streptavidin molecules and recombinant antibody fragments. The reduction of the solid phase binding surface to a size of a spot enabled denser binding of the target molecules, providing improved signal intensities and signal-to-background ratio when applied in different solid phase immunoassays. Streptavidin-biotin interactions are commonly utilised in numerous different bioaffinity assays and the ultimate nature of streptavidin to bind biotin is among the strongest non-covalent interaction reported between two biomolecules. In this study native core streptavidin was chemically modified to provide polymerised streptavidin molecules with altered adsorption properties. These streptavidin conjugates, when coated onto polystyrene surface, provided enhanced biotin binding capacity and surface stability when compared to a reference coating constructed with native streptavidin. Furthermore, the combination of chemically modified streptavidin, sitespecifically biotinylated antibody fragments and the spot coating technology provided highly dense solid phase coating with improved binding properties. The performance of the spot assay technology was further demonstrated in different immunoassay configurations. Human thyroid stimulating hormone (TSH) and human cardiac troponin I (cTnI) were used as model analytes to show the applicability of the highly sensitive spot-based solid-phase immunoassay for detection of very low levels of analytes. It was demonstrated that the spot technology provided an assay concept with enhanced sensitivity and short turn-around times, characteristics that are highly suitable for point-of-care applications.

Desenvolvimento de um método de MEFS com CG-DIC para determinação de 1,4 dioxana em amostras de cosméticos

A headspace solid-phase microextraction (HS-SPME) for the determination of 1,4 dioxane in cosmetics by gas chromatography is described. A manual SPME holder with 85 µm polyacrylate coating is utilized. The method is determined to have good resolution, satisfactory linerity (correlation coefficient r=0.997 for 0.20-10.00 mg Kg-1 range), a relative standard deviation of 6.3% and a detection limit of 5.00 µg Kg-1. Some cosmectic products were analyzed.

Tendências em modificação de eletrodos amperométricos para aplicações eletroanalíticas

The most relevant advances on the analytical applications of chemically modified electrodes (CME) are presented. CME have received great attention due to the possibility of electrode surface modification including chemisorption, composite generation and polymer coating. In recent years, the interest in CME has increased overall to improve the sensitivity and selectivity of the electroanalytical probes, considering the electron mediator incorporation and the new conducting polymers development. The general procedures employed for the electrode modification and the operational characteristics of some electrochemical sensors are discussed.