HIGH PRESSURE VAPOR-LIQUID EQUILIBRIA OF PALM FATTY ACIDS DISTILLATES-CARBON DIOXIDE SYSTEM

Vapor-Liquid equilibria of palm fatty acids distillates/carbon dioxide system has been investigated experimentally at temperatures of 333, 353, and 373 K and pressures of 20, 23, 26, and 29 MPa using the static method. Experimental data for the quasi-binary system palm fatty acids distillates/carbon dioxide has been correlated with Redlich-Kwong-Aspen equation of state. Modeling shows good agreement with experimental data. Selectivity obtained indicates that supercritical carbon dioxide is a reasonable solvent for separating saturated (palmitic acid) and unsaturated (oleic+linoleic acids) fatty acids from palm fatty acids distillates in a continuous multistage countercurrent column.

Processing of spent nickelcatalyst for fat recovery

Spent nickel catalyst (SNC) has the potential of insulting the quality of the environment in a number of ways. Its disposal has a pollution effect. Optimum recovery of fat from SNC, could save the environment and reduce the oil loss. Hexane has been the solvent of choice for oil extraction. Alternative solvents considered to have been safer have been evaluated. Hexane, isopropanol, ethanol and heptane were examined using soxhlet extraction. While hexane is more efficient in oil recovery from SNC, isopropanol proved to be very good in clear separation of oil from waste material and also provides high solvent recovery compared to other solvents. Isopropanol extraction with chill separation of miscella into lower oil-rich phase, and an upper, solvent-rich recyclable phase save mush energy of vaporization for distilling. An aqueous extraction process with immiscible solvent assisted was tested. Solvent like hexane added to SNC, and water added later with continuous stirring. The mixture was stirred for about 30 minutes, prior to centrifugation. Aqueous process extracted less amount of oil compared to solvent extraction.

Kraft recovery boilers – Principles and practice

This book was created as postgraduate lecture notes for Lappeenranta University of Technology's special course of steam power plants. But as with anything ever written the ideas shown have nurtured for a long time. Parts of these chapters have appeared elsewhere as individual papers or work documents. One of the most helpful episodes have been presentations and discussions during Pohto Operator training seminars. Input from those sessions can be seen in chapter firing. You who run recovery boilers, I salute you. The purpose of this text is to give the reader an overview of recovery boiler operation. Most parts of the recovery boiler operation are common to boilers burning other fuels. The furnace operation differs significantly from operation of other boiler furnaces. Oxygen rich atmosphere is needed to burn fuel efficiently. But the main function of recovery boiler is to reduce spent cooking chemicals. Reduction reactions happen best in oxygen deficient atmosphere. This dual, conflicting nature of recovery furnace makes understanding it so challenging. To understand the processes happening in the recovery furnace one must try to understand the detailed processes that might occur and their limitations. Therefore chapters on materials, corrosion and fouling have been added.

Otimização do cozimento de filé de frango empanado em forno de injeção direta de vapor

Foi estudado o efeito da temperatura do ar (205-215°C) e do tempo de cozimento (3,5 - 4,1 minutos), sobre a temperatura interna e o rendimento durante o cozimento do filé de frango empanado usando a metodologia de superfície de resposta, obtendo-se modelos estatísticos adequados. Verificou-se que as melhores condições de processo foram o emprego de temperaturas entre 206 e 209°C e tempos entre 2,5 e 3,6 minutos.

Determinação da pressão de vapor de compostos orgânicos por cromatografia gasosa

O conhecimento das pressões de vapor dos compostos naturais e suas propriedades críticas, de grande interesse para a extração supercrítica e impregnação de polímeros pelo processo supercrítico, é imprescindível para se fazer a modelagem termodinâmica do equilíbrio de fases. No entanto, a escassez de dados experimentais desses compostos, devida à alta volatilidade, ou facilidade à degradação em temperaturas baixas, requer a utilização de métodos especiais. Neste trabalho, determinaram-se as pressões de vapor da curcumina, nicotina, d-limoneno, beta-mirceno, citronelal e linalol, através de um método que utiliza medidas de tempo de retenção por cromatografia gasosa. Utilizou-se detector de ionização de chama e coluna em fase estacionária não polar, em condições isotérmicas. O método apresenta vantagens em relação a outros métodos, quanto à rapidez de análise, quantidade e repetibilidade das amostras. Para as determinações das pressões de vapor destes compostos naturais requer-se o conhecimento da temperatura normal de ebulição, ou temperatura de fusão e das pressões de vapor dos homólogos dos compostos analisados.

Enzymatic Synthesis, Recovery, and Purification of Ethyl β-ᴅ-glucopyranoside

A method to synthesize ethyl β-ᴅ-glucopyranoside (BEG) was searched. Feasibility of different ion exchange resins was examined to purify the product from the synthetic binary solution of BEG and glucose. The target was to produce at least 50 grams of 99 % pure BEG with a scaled up process. Another target was to transfer the batch process into steady-state recycle chromatography process (SSR). BEG was synthesized enzymatically with reverse hydrolysis utilizing β-glucosidase as a catalyst. 65 % of glucose reacted with ethanol into BEG during the synthesis. Different ion exchanger based resins were examined to separate BEG from glucose. Based on batch chromatography experiments the best adsorbent was chosen between styrene based strong acid cation exchange resins (SAC) and acryl based weak acid cation exchange resins (WAC). CA10GC WAC resin in Na+ form was chosen for the further separation studies. To produce greater amounts of the product the batch process was scaled up. The adsorption isotherms for the components were linear. The target purity was possible to reach already in batch without recycle with flowrate and injection size small enough. 99 % pure product was produced with scaled-up batch process. Batch process was transferred to SSR process utilizing the data from design pulse chromatograms and Matlab simulations. The optimal operating conditions for the system were determined. Batch and SSR separation results were compared and by using SSR 98 % pure products were gained with 40 % higher productivity and 40 % lower eluent consumption compared to batch process producing as pure products.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Mechanical and water vapor permeability properties of biodegradables films based on methylcellulose, glucomannan, pectin and gelatin

Mimic biological structures such as the cell wall of plant tissues may be an alternative to obtain biodegradable films with improved mechanical and water vapor barrier properties. This study aims to evaluate the mechanical properties and water vapor permeability (WVP) of films produced by using the solvent-casting technique from blended methylcellulose, glucomannan, pectin and gelatin. First, films from polysaccharides at pH 4 were produced. The film with the best mechanical performance (tensile strength = 72.63 MPa; elongation = 9.85%) was obtained from methylcellulose-glucomannan-pectin at ratio 1:4:1, respectively. Then, gelatin was added to this polysaccharide blend and the pH was adjusted to 4, 5 and 6. Results showed significant improvement in WVP when films were made at pH 5 and at polysaccharides/gelatin ratio of 90/10 and 10/90, reaching 0.094 and 0.118 g.mm/h.m².kPa as values, respectively. Films with the best mechanical properties were obtained from the blend of polysaccharides, whereas WVP was improved from the blend of polysaccharides and gelatin at pH 5.

Isolation and recovery of glycomacropeptide from milk whey by means of thermal treatment

During enzymatic process of cheese manufacturing, rennin cleaves κ-casein releasing two fractions: para-κ-casein and glycomacropeptide (GMP), which remains soluble in milk whey. GMP is a peptide with structural particularities such as chain carbohydrates linked to specific threonine residues, to which a great variety of biological activities is attributed. Worldwide cheese production has increased generating high volumes of milk whey that could be efficiently used as an alternative source of high quality peptide or protein in foodstuff formulations. In order to evaluate isolation and recovery on whey GMP by means of thermal treatment (90 °C), 18 samples (2 L each) of sweet whey, resuspended commercial whey (positive control) and acid whey (negative control) were processed. Indirect presence of GMP was verified using chemical tests and PAGE-SDS 15%. At 90 °C treated sweet whey, 14, 20 and 41 kDa bands were observed. These bands may correspond to olygomers of GMP. Peptide recovery showed an average of 1.5 g/L (34.08%). The results indicate that industrial scale GMP production is feasible; however, further research must be carried out for the biological and nutritional evaluation of GMP's incorporation to foodstuff as a supplement.

The effect of relative humidity on tensile strength and water vapor permeability in chitosan, fish gelatin and transglutaminase edible films

Abstract Composite films of chitosan, fish gelatin and microbial transglutaminase (MTgase) were developed. Films were produced by the casting method and dried at room temperature for 30 h, conditioned for 7 days at 30 °C at a relative humidity (RH) from 11 to 90%, and characterized. Chitosan:fish gelatin films in different proportions (100:0, 75:25, 50:50) with MTgase, were subjected to tensile properties and water vapor transmission (WVT) testing. The results showed that tensile strength decreased with an increase in RH and with an increase in gelatin content. Percent of elongation also increased with increasing RH and gelatin concentration. Water vapor transmission showed an increase proportional to an increase in RH with the presence of gelatin being unfavorable for reducing WVT. Results in this work allowed studying the effect of relative humidity on tensile and water vapor properties of chitosan and fish gelatin films.

Early initiation of dialysis: mortality and renal function recovery in acute kidney injury patients

INTRODUCTION: The decision of when to start dialysis in Acute Kidney Injury (AKI) patients with overt uremia is strongly established, however, when blood urea nitrogen (BUN) levels is < 100 mg/dL the timing of initiation of dialysis remains uncertain. Purpose: The aim of this study was to assess mortality and renal function recovery AKI patients started on dialysis at different BUN levels. METHODS: This was a retrospective study performed at Medical School Hospital, São Paulo, Brazil, enrolling 86 patients underwent to dialysis. RESULTS: Dialysis was started when BUN < 75 mg/dl in 23 patients (Group I) and BUN > 75 mg/dl in 63 patients (Group II). Hypervolemia and mortality were higher in Group I than in Group II (65.2% vs. 14.3% - p < 0.05, 39.1% vs. 68.9%- p < 0.05, respectively). Among survivors, the rate of renal function recovery was higher in Group I (71.4% and 36.8%, respectively - p < 0.05). Multivariate analysis showed that sepsis, age > 60 years, peritoneal dialysis and BUN > 75 mg/dl at dialysis initiation were independently related with mortality. CONCLUSIONS: Lower mortality and higher renal function recovery rates were associated with early dialysis initiated at lower BUN leves in AKI patients.

Recovery and purification of anthocyanins from purple-blue potato

The aim of this work was to study techniques to extract and purify of anthocyanins from purple-blue potato. This topic was determined as a master’s thesis and it was done in collaboration with the Food Chemistry and Food Development Department of University of Turku and Department of Chemical and Process Engineering at Lappeenranta University of Technology. At first, purple-blue potatoes were pretreated in four types of boiled, raw, freeze-dried and dried boiled potato for extraction. They were mixed with aqueous acidified ethanol (ethanol:water:acetic acid 40%:53%:7% v/v) for conventional extraction. Boiled potato was selected as a best pretreated potato. Different ethanol concentration and extraction time were examined and the mixture of 80% in 24 h resulted in maximum anthocyanin content (132.23 mg/L). As conventional extraction method of anthocyanins was non-selective, some of impurities such as free sugars might accelerate anthocyanin degradation. Therefore, to obtain anthocyanins in purified form, adsorption as a promising selective method was used to recovery and isolate anthocyanins. It was carried out with six adsorbents. Among those, Amberlite XAD-7HP, a nonionic acrylic ester adsorbent, was found to have the best performance. In an adsorption column, flow rate of 3 mL/min was selected as the loading flow rate among four tested flow rates. Eluent volume and flow rate were 3 BV of aqueous acidified ethanol (75%, v/v) and 1 mL/min for desorption. The quantification of the total anthocyanin contents was performed by pH-differential method using UV-vis spectrophotometer. The resulting anthocyanin solution after purification was almost free from free sugars which were the major cause for degradation of anthocyanins. The average anthocyanin concentration in the purified and concentrated sample was obtained 1752.89 mg/L.