Growth performance and management of a mixed rainforest tree plantation

Monoculture plantations of Pinus, Eucalyptus and Acacia have been established oil rainforest lands throughout the world. However, this type of reforestation generally supplies low quality timber and contributes to landscape simplification. Alternatives to exotic monoculture plantations are now beginning to gain momentum with farmers and landholders attempting to establish a variety of rainforest trees in small plantations. When compared to the well studied commercial species, knowledge concerning the growth and management of many of these rainforest species is in its infancy. To help expand this limited knowledge base an experimental plantation of 16 rainforest tree species in a randomised design was established near Mt. Mee, in south-eastern Queensland, Australia. Changes in growth, form (based on stem straightness, branch size and branchiness), crown diameters and leaf area of each species were examined over 5 years. Patterns of height growth were also measured monthly for 31 months. Species in this trial could be separated into three groups based on their overall growth after 5 years and their growth patterns. Early successional status, low timber density, high maximum photosynthetic rates and large total leaf areas were generally correlated to rapid height growth. Several species (including Araucaria cunninghamii, Elaeocarpus grandis, Flindersia brayleyana, Grevillea robusta and Khaya nyasica) had above average form and growth, while all species in the trial had considerable potential to have increased productivity through tree selection. As canopy closure occurred at the site between years four and five, growth increments declined. To reduce stand competition a number of different thinning techniques could be employed. However, simple geometric or productivity based thinnings appear to be inappropriate management techniques for this mixed species stand as they would either remove many of the best performing trees or nearly half the species in the trial. Alternatively, a form based thinning would maintain the site's diversity, increase the average form of the plantation and provide some productivity benefits.

Capillary break-up rheometry of low-viscosity elastic fluids

We investigate the dynamics of the capillary thinning and break-up process for low viscosity elastic fluids such as dilute polymer solutions. Standard measurements of the evolution of the midpoint diameter of the necking fluid filament are augmented by high speed digital video images of the break up dynamics. We show that the successful operation of a capillary thinning device is governed by three important time scales (which characterize the relative importance of inertial, viscous and elastic processes), and also by two important length scales (which specify the initial sample size and the total stretch imposed on the sample). By optimizing the ranges of these geometric parameters, we are able to measure characteristic time scales for tensile stress growth as small as 1 millisecond for a number of model dilute and semi-dilute solutions of polyethylene oxide (PEO) in water and glycerol. If the final aspect ratio of the sample is too small, or the total axial stretch is too great, measurements are limited, respectively, by inertial oscillations of the liquid bridge or by the development of the well-known beads-on-a-string morphology which disrupt the formation of a uniform necking filament. By considering the magnitudes of the natural time scales associated with viscous flow, elastic stress growth and inertial oscillations it is possible to construct an operability diagram characterizing successful operation of a capillary break-up extensional rheometer. For Newtonian fluids, viscosities greater than approximately 70 mPas are required; however for dilute solutions of high molecular weight polymer, the minimum Viscosity is substantially lower due to the additional elastic stresses arising from molecular extension. For PEO of molecular weight 2.10(6) g/mol, it is possible to measure relaxation times of order 1 ms in dilute polymer solutions with zero-shear-rate viscosities on the order of 2-10 mPas.

Changes to porcine blastocyst vitrification methods and improved litter size after transfer

The objective was to improve the protocol that was used to obtain the first reported piglets from transferred vitrified and warmed zona-intact blastocysts. Blastocysts were collected from superovulated sows and gilts, centrifuged to polarize lipid, vitrified, warmed and cultured for 24 h or transferred immediately. Removing the zona pellucida after warming increased the number of cells in the surviving blastocysts (zona-free 60.8 +/- 4.3, zona-intact 39.1 +/- 2.8; P < 0.05). Thinning the zona pellucida produced similar results to zona removal. Changing the basal medium of the vitrification and warming solutions from modified PBS to phosphate buffered NCSU-23 increased the number of cells (44.7 +/- 2.2 versus 56.0 +/- 3.9, respectively; P < 0.05). Reducing the plunge temperature of the liquid nitrogen from - 196 degrees C to less than -204 degrees C improved the embryo survival rate (61.9% versus 82.9%, respectively; P < 0.05). These modifications were incorporated into the vitrification protocol that was used to vitrify and warm 105 blastocysts (that were subsequently transferred into four recipients). Three recipients became pregnant, farrowing three litters (average litter size, 5.3; 18.8% embryo survival in farrowing sows). Changing the warming protocol to using sucrose rather than ethylene glycol resulted in a trend towards improved embryo survival (73.5% versus 91.2%) but this was not statistically significant. Incorporating this modification, 203 blastocysts were vitrified, warmed and transferred into seven recipients. Five became pregnant and 36 fetuses were recovered (average litter size 7.2; 24.8% embryo survival in pregnant sows) at Day 40 of pregnancy. In conclusion, changes made to the vitrification protocol improved pregnancy rate and in vivo embryo survival compared to an earlier study using the original protocol. (c) 2005 Elsevier Inc. All rights reserved.

Scaling laws for the critical rupture thickness or common thin films

Despite decades of experimental and theoretical investigation on thin films, considerable uncertainty exists in the prediction of their critical rupture thickness. According to the spontaneous rupture mechanism, common thin films become unstable when capillary waves. at the interfaces begin to grow. In a horizontal film with symmetry at the midplane. unstable waves from adjacent interfaces grow towards the center of the film. As the film drains and becomes thinner, unstable waves osculate and cause the film to rupture, Uncertainty sterns from a number of sources including the theories used to predict film drainage and corrugation growth dynamics. In the early studies, (lie linear stability of small amplitude waves was investigated in the Context of the quasi-static approximation in which the dynamics of wave growth and film thinning are separated. The zeroth order wave growth equation of Vrij predicts faster wave growth rates than the first order equation derived by Sharma and Ruckenstein. It has been demonstrated in an accompanying paper that film drainage rates and times measured by numerous investigations are bounded by the predictions of the Reynolds equation and the more recent theory of Manev, Tsekov, and Radoev. Solutions to combinations of these equations yield simple scaling laws which should bound the critical rupture thickness of foam and emulsion films, In this paper, critical thickness measurements reported in the literature are compared to predictions from the bounding scaling equations and it is shown that the retarded Hamaker constants derived from approximate Lifshitz theory underestimate the critical thickness of foam and emulsion films, The non-retarded Hamaker constant more adequately bounds the critical thickness measurements over the entire range of film radii reported in the literature. This result reinforces observations made by other independent researchers that interfacial interactions in flexible liquid films are not adequately represented by the retarded Hamaker constant obtained from Lifshitz theory and that the interactions become significant at much greater separations than previously thought. (c) 2005 Elsevier B.V. All rights reserved.

Bounding film drainage in common thin films

A review of thin film drainage models is presented in which the predictions of thinning velocities and drainage times are compared to reported values on foam and emulsion films found in the literature. Free standing films with tangentially immobile interfaces and suppressed electrostatic repulsion are considered, such as those studied in capillary cells. The experimental thinning velocities and drainage times of foams and emulsions are shown to be bounded by predictions from the Reynolds and the theoretical MTsR equations. The semi-empirical MTsR and the surface wave equations were the most consistently accurate with all of the films considered. These results are used in an accompanying paper to develop scaling laws that bound the critical film thickness of foam and emulsion films. (c) 2005 Elsevier B.V. All rights reserved.

Effectiveness of topical skin care provided in aged care facilities

Background The 2001 Australian census revealed that adults aged 65 years and over constituted 12.6% of the population, up from 12.1% in 1996. It is projected that this figure will rise to 21% or 5.1 million Australians by 2031. In 1998, 6% (134 000) of adults in Australia aged 65 years and over were residing in nursing homes or hostels and this number is also expected to rise. As skin ages, there is a decreased turnover and replacement of epidermal skin cells, a thinning subcutaneous fat layer and a reduced production of protective oils. These changes can affect the normal functions of the skin such as its role as a barrier to irritants and pathogens, temperature and water regulation. Generally, placement in a long-term care facility indicates an inability of the older person to perform all of the activities of daily living such as skin care. Therefore, skin care management protocols should be available to reduce the likelihood of skin irritation and breakdown and ultimately promote comfort of the older person. Objectives The objective of this review was to determine the best available evidence for the effectiveness and safety of topical skin care regimens for older adults residing in long-term aged care facilities. The primary outcome was the incidence of adverse skin conditions with patient satisfaction considered as a secondary outcome. Search strategy A literature search was performed using the following databases: PubMed (NLM) (1966–4/2003), Embase (1966–4/2003), CINAHL (1966–4/2003), Current Contents (1993–4/2003), Cochrane Library (1966–2/2003), Web of Science (1995–12/2002), Science Citation Index Expanded and ProceedingsFirst (1993–12/2002). Health Technology Assessment websites were also searched. No language restrictions were applied. Selection criteria Systematic reviews of randomised controlled trials, randomised and non-randomised controlled trials evaluating any non-medical intervention or program that aimed to maintain or improve the integrity of skin in older adults were considered for inclusion. Participants were 65 years of age or over and residing in an aged care facility, hospital or long-term care in the community. Studies were excluded if they evaluated pressure-relieving techniques for the prevention of skin breakdown. Data collection and analysis Two independent reviewers assessed study eligibility for inclusion. Study design and quality were tabulated and relative risks, odds ratios, mean differences and associated 95% confidence intervals were calculated from individual comparative studies containing count data. Results The resulting evidence of the effectiveness of topical skin care interventions was variable and dependent upon the skin condition outcome being assessed. The strongest evidence for maintenance of skin condition in incontinent patients found that disposable bodyworn incontinence protection reduced the odds of deterioration of skin condition compared with non-disposable bodyworns. The best evidence for non-pressure relieving topical skin care interventions on pressure sore formation found the no-rinse cleanser Clinisan to be more effective than soap and water at maintaining healthy skin (no ulcers) in elderly incontinent patients in long-term care. The quality of studies examining the effectiveness of topical skin care interventions on the incidence of skin tears was very poor and inconclusive. Topical skin care for prevention of dermatitis found that Sudocrem could reduce the redness of skin compared with zinc cream if applied regularly after each pad change, but not the number of lesions. Topical skin care on dry skin found the Bag Bath/Travel Bath no-rinse skin care cleanser to be more effective at preventing overall skin dryness and most specifically flaking and scaling when compared with the traditional soap and water washing method in residents of a long-term care facility. Information on the safety of topical skin care interventions is lacking. Therefore, because of the lack of evidence, no recommendation on the safety on any intervention included in this review can be made.

How the west was once: vegetation change in south-west Queensland from 1930 to 1995

Conflicting perceptions of past and present rangeland condition and limited historical data have led to debate regarding the management of vegetation in pastoral landscapes both internationally and in Australia. In light of this controversy we have sought to provide empirical evidence to determine the trajectory of vegetational change in a semi-arid rangeland for a significant portion of the 20th century using a suite of proxy measures. Ambathala Station, approximately 780 km west of Brisbane, in the semi-arid rangelands of south-western Queensland, Australia. We excavated stratified deposits of sheep manure which had accumulated beneath a shearing shed between the years 1930 and 1995. Multi-proxy data, including pollen and leaf cuticle analyses and analysis of historical aerial photography were coupled with a fine resolution radiocarbon chronology to generate a near annual history of vegetation on the property and local area. Aerial photography indicates that minor (< 5%) increases in the density of woody vegetation took place between 1951 and 1994 in two thirds of the study area not subjected to clearing. Areas that were selectively or entirely cleared prior to the 1950s (approximately 16% of the study area) had recovered to almost 60% of their original cover by the 1994 photo period. This slight thickening is only partially evident from pollen and leaf cuticle analyses of sheep faeces. Very little change in vegetation is revealed over the nearly 65 years based on the relative abundances of pollen taxonomic groups. Microhistological examination of sheep faeces provides evidence of dramatic changes in sheep diet. The majority of dietary changes are associated with climatic events of sustained above-average rainfall or persistent drought. Most notable in the dietary analysis is the absence of grass during the first two decades of the record. In contrast to prevailing perceptions and limited research into long-term vegetation change in the semi-arid areas of eastern Australia, the record of vegetation change at the Ambathala shearing shed indicates only a minor increase in woody vegetation cover and no decrease in grass cover on the property over the 65 years of pastoral activity covered by the study. However, there are marked changes in the abundance of grass cuticles in sheep faeces. The appearance and persistence of grass in sheep diets from the late 1940s can be attributed to the effects of periods of high rainfall and possibly some clearing and thinning of vegetation. Lower stock numbers may have allowed grass to persist through later drought years. The relative abundances of major groups of plant pollen have not changed significantly over the past 65 years.

Rehabilitating degraded forest land in central Vietnam with mixed native species plantings

This paper examines the use of Acacia as a nurse crop to overcome some of the ecological and economic impediments to reforestation of degraded areas dominated by grasses including Imperata cylindrica. The study site at Hai Van Pass in central Vietnam was initially reforested using Acacia auriculiformis. After 8 years these stands were thinned and under-planted with Hopea odorata, Dipterocarpus alatus, Parashorea chinensis, Tarrietia javanica, Parashorea stellata, Scaphium lychnophorum, Peltophorum dasyrhachis var. tonkinensis and other high-value native species. At the time of field assessment (early 2004), the Acacia trees were aged between 16 and 18 years and basal area ranged from 9 to 13 m(2) ha(-1) after several thinnings. Acacias facilitated the establishment of native species, but after 6-7 years of growth, further thinning is needed to maintain growth rates. In addition to assisting the establishment of native species, the Acacia nurse crop should provide a revenue stream (NPV about US$ 180, or IRR 19%) sufficient to cover the establishment costs of the underplanted native species (about US$ 100). (c) 2006 Published by Elsevier B.V.

Drop formation and breakup of low viscosity elastic fluids: Effects of molecular weight and concentration

The dynamics of drop formation and pinch-off have been investigated for a series of low viscosity elastic fluids possessing similar shear viscosities, but differing substantially in elastic properties. On initial approach to the pinch region, the viscoelastic fluids all exhibit the same global necking behavior that is observed for a Newtonian fluid of equivalent shear viscosity. For these low viscosity dilute polymer solutions, inertial and capillary forces form the dominant balance in this potential flow regime, with the viscous force being negligible. The approach to the pinch point, which corresponds to the point of rupture for a Newtonian fluid, is extremely rapid in such solutions, with the sudden increase in curvature producing very large extension rates at this location. In this region the polymer molecules are significantly extended, causing a localized increase in the elastic stresses, which grow to balance the capillary pressure. This prevents the necked fluid from breaking off, as would occur in the equivalent Newtonian fluid. Alternatively, a cylindrical filament forms in which elastic stresses and capillary pressure balance, and the radius decreases exponentially with time. A (0+1)-dimensional finitely extensible nonlinear elastic dumbbell theory incorporating inertial, capillary, and elastic stresses is able to capture the basic features of the experimental observations. Before the critical "pinch time" t(p), an inertial-capillary balance leads to the expected 2/3-power scaling of the minimum radius with time: R-min similar to(t(p)-t)(2/3). However, the diverging deformation rate results in large molecular deformations and rapid crossover to an elastocapillary balance for times t>t(p). In this region, the filament radius decreases exponentially with time R-min similar to exp[(t(p)-t)/lambda(1)], where lambda(1) is the characteristic time constant of the polymer molecules. Measurements of the relaxation times of polyethylene oxide solutions of varying concentrations and molecular weights obtained from high speed imaging of the rate of change of filament radius are significantly higher than the relaxation times estimated from Rouse-Zimm theory, even though the solutions are within the dilute concentration region as determined using intrinsic viscosity measurements. The effective relaxation times exhibit the expected scaling with molecular weight but with an additional dependence on the concentration of the polymer in solution. This is consistent with the expectation that the polymer molecules are in fact highly extended during the approach to the pinch region (i.e., prior to the elastocapillary filament thinning regime) and subsequently as the filament is formed they are further extended by filament stretching at a constant rate until full extension of the polymer coil is achieved. In this highly extended state, intermolecular interactions become significant, producing relaxation times far above theoretical predictions for dilute polymer solutions under equilibrium conditions. (C) 2006 American Institute of Physics

Geochronology of the Pengjiakuang and Rushan gold deposits, Eastern Jiaodong Gold Province, Northeastern China: Implications for regional mineralization and geodynamic setting

The Jiaodong gold province, the largest gold-producing district in China, is located in the jiaodong peninsula at the eastern margin of the North China craton and bounded by the continental scale Tan-Lu fault, 40 kin to the west. Previous geochronological studies suggest that pervasive gold deposition took place in the western part of the province between 122 and 119 Ma. Here we report high-quality Ar-40/Ar-39 ages of the Pengjiakuang and Rushan deposits from the eastern part of the jiaodong gold province, placing additional chronological constraints on the timing of regional mineralization. Seven sericite grains extracted from auriferous alteration assemblages at the Pengiiakuang deposit yielded well-defined plateau ages between 120.9 +/- 0.4 and 119.1 +/- 0.2 Ma (2 sigma). Three separates of igneous biotite from a sample of the Queshan gneissic granite, adjacent to the Pengjiakuang deposit, gave reproducible plateau ages of 124.6 +/- 0.6 to 123.9 +/- 0.4 Ma (2 sigma). Six sericite separates front two samples in the Rushan deposit yielded Ar-40/Ar-39 plateau ages at 109.3 +/- 0.3 to 107.7 +/- 0.5 Ma (2 sigma), whereas biotite from the Kunyushan monzogranite that hosts the Rushan deposit had plateau ages ranging from 129.0 +/- 0.6 to 126.9 +/- 0.6 Ma (3 separates front one sample). The apparent age gap between hydrothermal sericite and magmtic biotite from both deposits, together with the similar argon closure temperatures for these mica minerals, suggest that gold mineralization had no direct relationship to the granitoid magmatism. Instead, gold deposition coincided with the emplacement of mafic to intermediate dikes widespread in the jiaodong gold province, which have been dated at ca. 122 to 119 Ma and, less commonly, at 110 to 102 Ma. The new Ar-40/Ar-39 ages from the eastern jiaodong peninsula, when combined with published data from the western part suggest that gold mineralization was broadly contemporaneous throughout the district. The Early Cretaceous gold mineralization also is widely developed in four other major gold districts along the Tan-Lu fault. The temporal and spatial correlation of these gold deposits with mafic to intermediate dikes commonly found in most mineralized areas, the presence of well-documented metamorphic core complexes and half-graben basins along the Tan-Lu fault, and voluminous basalts therein, suggest that the Early Cretaceous was an important period of lithospheric extension, possibly caused by the late Mesozoic lithospheric thinning beneath the eastern block of the North China craton. Lithospheric thinning and extension could have resulted in abnormally high heat and fluid fluxes necessary for large-scaled gold mineralization.

Local geometric changes in left ventricular remodeling post-infarction can lead to apparent reduction in scar thickness

Serial reduction in scar thickness has been shown in animal models. We sought whether this reduction in scar thickness may be a result of dilatation of the left ventricle (LV) with stretching and thinning of the wall. Contrast enhanced magnetic resonance imaging (CMRI) was performed to delineate radial scar thickness in 25 patients (age 63±10, 21 men) after myocardial infarction. The LV was divided into 16 segts and the absolute radial scar thickness (ST) and percentage scar to total wall thickness (%ST) were measured. Regional end diastolic (EDV) and end systolic volumes (ESV) of corresponding segments were measured on CMRI. All patients underwent revascularization and serial changes in ST, %ST, and regional volumes were assessed with a mean follow up of 15±5 months. CMRI identified a total of 93 scar segments. An increase in EDV or ESV was associated with a serial reduction inST(versusEDV, r =−0.3, p = 0.01; versusESV, r =−0.3, p = 0.005) and%ST(versusEDV, r =−0.2, p = 0.04; versus ESV, r =−0.3, p = 0.001). For segts associated with a positive increase in EDV (group I) or ESV (group II) there was a significant decrease in ST and %ST, but in those segts with stable EDV (group III) or ESV (group IV) there were no significant changes in ST and %ST (Table).

Stand density management in rainforest plantations

Trees in plantations established for timber production are usually grown at a sufficiently high density that canopy closure occurs within a relatively short time after planting. The trees then shade and outcompete most herbs, shrubs or grasses growing at the site. The closer the spacing (i.e. the greater the density) the faster this will occur. Subsequently, as the trees grow larger, this between-species competition is replaced by within-species competition. If unmanaged, this competition can reduce the commercial productivity of the plantation. Thus, there are two management dilemmas. One is knowing the best initial planting density. The second is knowing how to management the subsequent between-tree competition in order to optimize overall plantation timber productivity. In this chapter we consider initial spacing and thinning for high value timber trees grown in single and mixed species plantations. From growth studies in stands of different ages recommendations are proposed for managing both types of plantations where the primary objective is timber production. It seems that many rainforest species will require more space to achieve optimal growth than most eucalypts and conifers. On the other hand many rainforest species do not have strong apical dominance. Care will be needed to balance these two attributes.

Optical fibre sensors with applications in gas and biological sensing

This thesis describes the study of various grating based optical fibre sensors for applications in refractive index sensing. The sensitivity of these sensors has been studied and in some cases enhanced using novel techniques. The major areas of development are as follows. The sensitivity of long period gratings (LPGs) to surrounding medium refractive index (SRI) for various periods was investigated. The most sensitive period of LPG was found to be around 160 µm and this was due to the core mode coupling to a single cladding mode but phase matching at two wavelength locations, creating two attenuation peaks, close to the waveguide dispersion turning point. Large angle tilted fibre gratings (TFGs) have similar behaviour to LPGs, in that they couple to the co-propagating cladding modes. The tilted structure of the index modulation within the core of the fibre gives rise to a polarisation dependency, differing the large angle TFG from a LPG. Since the large angle TFG couple to the cladding mode they are SRI sensitive, the sensitivity to SRI can be further increased through cladding etching using HF acid. The thinning of the cladding layer caused a reordering of the cladding modes and shifted to more SRI sensitive cladding modes as the investigation discovered. In a SRI range of 1.36 to 1.40 a sensitivity of 506.9 nm/URI was achieved for the etched large angle TFG, which is greater than the dual resonance LPG. UV inscribed LPGs were coated with sol-gel materials with high RIs. The high RI of the coating caused an increase in cladding mode effective index which in turn caused an increase in the LPG sensitivity to SRI. LPGs of various periods of LPG were coated with sol-gel TiO2 and the optimal thickness was found to vary for each period. By coating of the already highly SRI sensitive 160µm period LPG (which is a dual resonance) with a sol-gel TiO2, the SRI sensitivity was further increased with a peak value of 1458 nm/URI, which was an almost 3 fold increase compared to the uncoated LPG. LPGs were also inscribed using a femtosecond laser which produced a highly focused index change which was no uniform throughout the core of the optical fibre. The inscription technique gave rise to a large polarisation sensitivity and the ability to couple to multiple azimuthal cladding mode sets, not seen with uniform UV inscribed gratings. Through coupling of the core mode to multiple sets of cladding modes, attenuation peaks with opposite wavelength shifts for increasing SRI was observed. Through combining this opposite wavelength shifts, a SRI sensitivity was achieved greater than any single observed attenuations peak. The maximum SRI achieved was 1680 nm/URI for a femtosecond inscribed LPG of period 400 µm. Three different types of surface plasmon resonance (SPR) sensors with a multilayer metal top coating were investigated in D shape optical fibre. The sensors could be separated into two types, utilized a pre UV inscribed tilted Bragg grating and the other employed a post UV exposure to generate surface relief grating structure. This surface perturbation aided the out coupling of light from the core but also changed the sensing mechanism from SPR to localised surface plasmon resonance (LSPR). This greatly increased the SRI sensitivity, compared to the SPR sensors; with the gold coated top layer surface relief sensor producing the largest SRI sensitivity of 2111.5nm/URI was achieved. While, the platinum and silver coated top layer surface relief sensors also gave high SRI sensitivities but also the ability to produce resonances in air (not previously seen with the SPR sensors). These properties were employed in two applications. The silver and platinum surface relief devices were used as gas sensors and were shown to be capable of detecting the minute RI change of different gases. The calculated maximum sensitivities produced were 1882.1dB/URI and 1493.5nm/URI for silver and platinum, respectively. Using a DFB laser and power meter a cheap alternative approach was investigated which showed the ability of the sensors to distinguish between different gases and flow rates of those gases. The gold surface relief sensor was coated in a with a bio compound called an aptamer and it was able to detect various concentrations of a biological compound called Thrombin, ranging from 1mM to as low as 10fM. A solution of 2M NaCl was found to give the best stripping results for Thrombin from the aptamer and showed the reusability of the sensor. The association and disassociation constants were calculated to be 1.0638×106Ms-1 and 0.2482s-1, respectively, showing the high affinity of the Aptamer to thrombin. This supports existing working stating that aptamers could be alternative to enzymes for chemical detection and also helps to explain the low detection limit of the gold surface relief sensor.

Investigation of the oxidative degradation mechanisms and melt stabilisation of a new generation metallocene polytehylene

The two main objectives of the research work conducted were firstly, to investigate the processing and rheological characteristics of a new generation metallocene catalysed linear low density polyethylene (m-LLDPE), in order to establish the thermal oxidative degradation mechanism, and secondly, to examine the role of selected commercial stabilisers on the melt stability of the polymers. The unstabilised m-LLDPE polymer was extruded (pass I) using a twin screw extruder, at different temperatures (210-285°C) and screw speeds (50-20rpm) and was subjected to multiple extrusions (passes, 2-5) carried out under the same processing conditions used in the first pass. A traditional Ziegler/Natta catalysed linear low density polyethylene (z-LLDPE) produced by the same manufacturer was also subjected to a similar processing regime in order to compare the processability and the oxidative degradation mechanism (s) of the new m-LLDPE with that of the more traditional z-LLDPE. The effect of some of the main extrusion characteristics of the polymers (m-LLDPE and z-LLDPE) on their melt rheological behaviour was investigated by examining their melt flow performance monitored at two fixed low shear rate values, and their rheological behaviour investigated over the entire shear rates experienced during extrusion using a twin-bore capillary rheometer. Capillary rheometric measurements, which determine the viscous and elastic properties of polymers, have shown that both polymers are shear thinning but the m-LLDPE has a higher viscosity than z-LLDPE and the extent of reduction in viscosity of the former when the extrusion temperature was increased from 210°C to 285°C was much higher than in the case of the z-LLDPE polymer. This was supplied by the findings that the m-LLDPE polymer required higher power consumption under all extrusion conditions examined. It was fUliher revealed that the m-LLDPE undergoes a higher extent of melt fracture, the onset of which occurs under much lower shear rates than the Ziegler-based polymer and this was attributed to its higher shear viscosity and narrower molecular weight distribution (MWD). Melt flow measurements and GPC have shown that after the first extrusion pass, the initial narrower MWD of m-LLDPE is retained (compared to z-LLDPE), but upon further multiple extrusion passes it undergoes much faster broadening of its MWD which shifts to higher Mw polymer fractions, paliicularly at the high screw speeds. The MWD of z-LLDPE polymer on the other hand shifts towards the lower Mw end. All the evidence suggest therefore the m-LLDPE undergoes predominantly cross-linking reactions under all processing conditions whereas z-LLDPE undergoes both cross-linking and chain scission reactions with the latter occurring predominantly under more severe processing conditions (higher temperatures and screw speeds, 285°CI200rpm). The stabilisation of both polymers with synergistic combinations of a hindered phenol (Irganox 1076) and a phosphite (Weston 399) at low concentrations has shown a high extent of melt stabilisation in both polymers (extrusion temperatures 210-285°C and screw speeds 50-200rpm). The best Irganox 1076/Weston 399 system was found to be at an optimum 1:4 w/w ratio, respectively and was found to be most effective in the z-LLDPE polymer. The melt stabilising effectiveness of a Vitamin E/Ultranox 626 system used at a fraction of the total concentration of Irganox 1076/Weston 399 system was found to be higher in both polymers (under all extrusion conditions). It was found that AOs which operate primarily as alkyl (Re) radical scavengers are the most effective in inhibiting the thermal oxidative degradation of m-LLDPE in the melt; this polymer was shown to degrade in the melt primarily via alky radicals resulting in crosslinking. Metallocene polymers stabilised with single antioxidants of Irganox HP 136 (a lactone) and Irganox E201 (vitamin E) produced the highest extent of melt stability and the least discolouration during processing (260°C/1 OOrpm). Furthermore, synergistic combinations of Irganox HP I 36/Ultranox 626 (XP-60) system produced very high levels of melt and colour stability (comparable to the Vitamin E based systems) in the mLLDPE polymer. The addition of Irganox 1076 to an Irganox HP 136/Ultranox 626 system was found not to result in increasing melt stability but gave rise to increasing discolouration of the m-LLDPE polymer. The blending of a hydroxylamine (lrgastab FS042) with a lactone and Vitamin E (in combination with a phosphite) did not increase melt stability but induced severe discolouration of resultant polymer samples.

Mechanical properties of sheet metal under forming conditions

In the bulge test, a sheet metal specimen is clamped over a circular hole in a die and formed into a bulge by the hydraulic pressure on one side of the specirnen. As the unsupported part of the specimen is deformed in this way, its area is increased, in other words, the material is generally stretched and its thickness generally decreased. The stresses causing this stretching action are the membrane stresses in the shell generated by the hydraulic pressure, in the same way as the rubber in a toy balloon is stretched by the membrane stresses caused by the air inside it. The bulge test is a widely used sheet metal test, to determine the "formability" of sheet materials. Research on this forming process (2)-(15)* has hitherto been almost exclusively confined to predicting the behaviour of the bulged specimen through the constitutive equations (stresses and strains in relation to displacements and shapes) and empirical work hardening characteristics of the material as determined in the tension test. In the present study the approach is reversed; the stresses and strains in the specimen are measured and determined from the geometry of the deformed shell. Thus, the bulge test can be used for determining the stress-strain relationship in the material under actual conditions in sheet metal forming processes. When sheet materials are formed by fluid pressure, the work-piece assumes an approximately spherical shape, The exact nature and magnitude of the deviation from the perfect sphere can be defined and measured by an index called prolateness. The distribution of prolateness throughout the workpiece at any particular stage of the forming process is of fundamental significance, because it determines the variation of the stress ratio on which the mode of deformation depends. It is found. that, before the process becomes unstable in sheet metal, the workpiece is exactly spherical only at the pole and at an annular ring. Between the pole and this annular ring the workpiece is more pointed than a sphere, and outside this ring, it is flatter than a sphere. In the forming of sheet materials, the stresses and hence the incremental strains, are closely related to the curvatures of the workpiece. This relationship between geometry and state of stress can be formulated quantitatively through prolateness. The determination of the magnitudes of prolateness, however, requires special techniques. The success of the experimental work is due to the technique of measuring the profile inclination of the meridional section very accurately. A travelling microscope, workshop protractor and surface plate are used for measurements of circumferential and meridional tangential strains. The curvatures can be calculated from geometry. If, however, the shape of the workpiece is expressed in terms of the current radial (r) and axial ( L) coordinates, it is very difficult to calculate the curvatures within an adequate degree of accuracy, owing to the double differentiation involved. In this project, a first differentiation is, in effect, by-passed by measuring the profile inclination directly and the second differentiation is performed in a round-about way, as explained in later chapters. The variations of the stresses in the workpiece thus observed have not, to the knowledge of the author, been reported experimentally. The static strength of shells to withstand fluid pressure and their buckling strength under concentrated loads, both depend on the distribution of the thickness. Thickness distribution can be controlled to a limited extent by changing the work hardening characteristics of the work material and by imposing constraints. A technique is provided in this thesis for determining accurately the stress distribution, on which the strains associated with thinning depend. Whether a problem of controlled thickness distribution is tackled by theory, or by experiments, or by both combined, the analysis in this thesis supplies the theoretical framework and some useful experimental techniques for the research applied to particular problems. The improvement of formability by allowing draw-in can also be analysed with the same theoretical and experimental techniques. Results on stress-strain relationships are usually represented by single stress-strain curves plotted either between one stress and one strain (as in the tension or compression tests) or between the effective stress and effective strain, as in tests on tubular specimens under combined tension, torsion and internal pressure. In this study, the triaxial stresses and strains are plotted simultaneously in triangular coordinates. Thus, both stress and strain are represented by vectors and the relationship between them by the relationship between two vector functions. From the results so obtained, conclusions are drawn on both the behaviour and the properties of the material in the bulge test. The stress ratios are generally equal to the strain-rate ratios (stress vectors collinear with incremental strain vectors) and the work-hardening characteristics, which apply only to the particular strain paths are deduced. Plastic instability of the material is generally considered to have been reached when the oil pressure has attained its maximum value so that further deformation occurs under a constant or lower pressure. It is found that the instability regime of deformation has already occurred long before the maximum pressure is attained. Thus, a new concept of instability is proposed, and for this criterion, instability can occur for any type of pressure growth curves.