Ohjelmistoyritysten liiketoimintamallit Kaakkois-Suomessa

Tutkielman tavoitteena on tunnistaa Kaakkois-Suomen alueella olevat ohjelmistoyritysten tyypilliset yritysryhmät ja kuvata niiden toimintaa. Tunnistamalla alueen ohjelmistoyrityksille ominaiset piirteet työ antaa myös pohjaa tulevien kehityskohteiden löytämisessä ja kehitystoimenpiteiden kohdistamisessa useisiin samantyyppisiin yrityksiin. Työn taustaksi esitellään ohjelmistoalaa ja ohjelmistoliiketoiminnan malleja, joiden pohjalta muodostetaan viitekehys alueen ohjelmistoyritysten empiiriseen tarkasteluun. Empiriaosuudessa tarkastellaan työn teoreettisessa osiossa esitettyjen liiketoimintamallien toteutumista Kaakkois-Suomessa ja ryhmitellään alueen ohjelmistoyritykset erottelevimpien tekijöiden avulla. Tutkimus on luonteeltaan kvantitatiivinen kokonaistutkimus Kaakkois-Suomen ohjelmistoyrityksistä, ja tutkimusotteeltaan deskriptiivinen eli kuvaileva. Tutkimusaineisto perustui tutkimusryhmän suorittamaan strukturoituun haastatteluun, jossa haastateltiin kaikkiaan 58 ohjelmistoyrityksen vastuuhenkilöitä. Tutkimustulosten perusteella alueelta pystyttiin tunnistamaan neljä toimintatavoiltaan erilaista ohjelmistoliiketoiminnan perustyyppiä: asiakaslähtöiset toimijat (26 toimipaikkaa), räätälöijät (14 toimipaikkaa), integroijat (10 toimipaikkaa) ja tuotteistajat (8 toimipaikkaa). Tulokset osoittavat, että perinteisten ohjelmistoalan liiketoimintamallien kuvaukset ja niistä tehtävät yleistykset antavat hyvän lähtökohdan ohjelmistoyritysten tarkasteluun. Kuitenkin perinteisten ohjelmistoalan liiketoimintamallien antama näkökulma on liian rajoittunut,jos halutaan tarkastella syvällisemmin ohjelmistoyritysten liiketoimintalogiikkaa.

Unlicensed Mobile Access Concept from Testing Point of View

Viime vuosikymmenien aikana kommunikaatioteknologiat ovat kehittyneet erittäin paljon. Uusia verkkoja, liityntätekniikoita, protokollia ja päätelaitteita on luotu alati kehittyvällä vauhdilla, eikä hidastumisen merkkejä ole näkyvissä. Varsinkin mobiilisovellukset ovat kasvattaneet markkinaosuuksiaan viime aikoina. Unlicensed MobileAccess (UMA) on uusi liityntätekniikka mobiilipäätelaitteille, joka mahdollistaa liitynnän GSM- runkoverkkoon WLAN- tai Bluetooth - tekniikoiden avulla. Tämä diplomityö keskittyy UMAan liittyviin teknologioihin, joita tarkastellaan lähemmin ensimmäisissä kappaleissa. Tavoitteena on esitellä, mitä UMA merkitsee, ja kuinka eri tekniikoita voidaan soveltaa sen toteutuksissa. Ennenkuin uusia teknologioita voidaan soveltaa kaupallisesti, täytyy niiden olla kokonaisvaltaisesti testattuja. Erilaisia testausmenetelmiä sovelletaan laitteistonja ohjelmiston testaukseen, mutta tavoite on kuitenkin sama, eli vähentää testattavan tuotteen epäluotettavuutta ja lisätä sen laatua. Vaikka UMA käsittääkin pääasiassa jo olemassa olevia tekniikoita, tuo se silti mukanaan uuden verkkoelementin ja kaksi uutta kommunikaatioprotokollaa. Ennen kuin mitään UMAa tukevia ratkaisuja voidaan tuoda markkinoille, monia erilaisia testausmenetelmiä on suoritettava, jotta varmistutaan uuden tuotteen oikeasta toiminnallisuudesta. Koska tämä diplomityö käsittelee uutta tekniikkaa, on myös testausmenetelmien yleisen testausteorian käsittelemiselle varattu oma kappale. Kappale esittelee erilaisia testauksen näkökulmia ja niihin perustuen rakennetaan myös testausohjelmisto. Tavoitteena on luoda ohjelmisto, jota voidaan käyttää UMA-RR protokollan toiminnan varmentamiseen kohdeympäristössä.

Kromatografisen erotusfaasin huokoskoon karakterisointi

Työssä tutkittiin sulfonoitujen polystyreenidivinyylibentseenirunkoisten geeli-, meso- ja makrohuokoistenioninvaihtohartsien rakennetta käyttäen useita eri karakterisointimenetelmiä. Lisäksi työssä tutkittiin hartsien huokoskoon vaikutusta aminohappojen kromatografisessa erotuksessa. Työn pääpaino oli hartsien huokoskoon ja huokoisuuden määrittämisessä. Sen selvittämiseksi käytettiin hyväksi elektronimikroskopiaa, typpiadsorptiomittauksia, sekä käänteistä kokoekskluusiokromatografiaa. Parhaat tulokset saatiin käänteisellä kokoekskluusiokromatografialla, joka perustuu erikokoisten dekstraanipolymeerien käyttöön mallimolekyyleinä. Menetelmä sopii meso- ja makrohuokoisuuden tutkimiseen, mutta sen heikkoutena on erittäin pitkä mittausaika. Menetelmä antaa myös huokoskokojakauman, mutta yhden hartsin mittaaminen voi kestää viikon. Menetelmää muutettiin siten, että käytettiin määritettävää huokoskokoaluetta kuvaavien kahden dekstraanipolymeerin seosta. Kromatografiset ajo-olosuhteet optimoitiin sellaisiksi, että injektoidussa seoksessa olevien dekstraanien vastehuiput erottuivat toisistaan. Tällöin voitiin luotettavasti määrittää tutkittavan stationaarifaasin suhteellinen huokoisuus. Tätä työssä kehitettyä nopeaa käänteiseen kokoekskluusiokromatografiaan perustuvaa menetelmää kutsutaan kaksipistemenetelmäksi. Hartsien sulfonihapporyhmien määrää ja jakautumista tutkittiin määrittämällä hartsien kationinvaihtokapasiteetti sekä tutkimalla hartsin pintaa konfokaali-Raman-spektroskopian avulla. Sulfonihapporyhmien ioninvaihtokyvyn selvittämiseksi mitattiin K+-muotoon muutetusta hartsista S/K-suhde poikkileikkauspinnasta. Tulosten perusteella hartsit olivat tasaisesti sulfonoituneet ja 95 % rikkiatomeista oli toimivassa ioninvaihtoryhmässä. Aminohappojen erotuksessa malliaineina oli lysiini, seriini ja tryptofaani. Hartsi oli NH4+-muodossa ja petitilavuus oli 91 mL. Eluenttina käytettiin vettä, jonka pH oli 10. Paras tulos saatiin virtausnopeudella 0,1 mL/min, jolla kaikki kolme aminohappoa erottuivat toisistaan Finex Oy:n mesohuokoisella KEF78-hartsilla. Muilla tutkituilla hartseilla kaikki kolme aminohappoa eivät missään ajo-olosuhteissa erottuneet täysin.

Analysis of a finite volume method for a cross-diffusion model in population dynamics

The main goal of this paper is to propose a convergent finite volume method for a reactionâeuro"diffusion system with cross-diffusion. First, we sketch an existence proof for a class of cross-diffusion systems. Then the standard two-point finite volume fluxes are used in combination with a nonlinear positivity-preserving approximation of the cross-diffusion coefficients. Existence and uniqueness of the approximate solution are addressed, and it is also shown that the scheme converges to the corresponding weak solution for the studied model. Furthermore, we provide a stability analysis to study pattern-formation phenomena, and we perform two-dimensional numerical examples which exhibit formation of nonuniform spatial patterns. From the simulations it is also found that experimental rates of convergence are slightly below second order. The convergence proof uses two ingredients of interest for various applications, namely the discrete Sobolev embedding inequalities with general boundary conditions and a space-time $L^1$ compactness argument that mimics the compactness lemma due to Kruzhkov. The proofs of these results are given in the Appendix.

Palveluhankintojen analysointi ja mittaaminen, case Stora Enso Saimaa Services Oy

Tutkimuksen tavoitteena oli luoda Stora Enso Saimaa Services Oy:lle palveluhankintojen suorituskyvyn mittaristo Balanced Scorecardin avulla. Yrityksen palveluhankintakentän kirjavuuden vuoksi työ rajattiin koskemaan vain Etelä-Karjalan Yrityksiltä (= EKY) ostettavia kunnossapitopalveluja. Mittariston muodostamisen lähtökohtana oli hankintatoimen strateginen tavoite, kokonaiskustannusten alentaminen. Tämä tavoite konkretisoituu parhaiten hankintojen elinkaarikustannusten minimoimisena. Työssä käytettiin kvalitatiivista tutkimusmenetelmää. Tutkimuskohdetta analysoitiin tapaustutkimusmenetelmällä. Aineisto kerättiin sisäisille asiakkaille suunnatulla puolistrukturoidulla haastatteluilla, ostajien ajankäytönseurantakyselyllä sekä osallistuvalla havainnoinnilla. Haastatteluja tehtiin 10 ja kyselyjä 6. Palveluhankintojen elinkaarikustannusten ja mittaamisen osalta on tehty tutkimuksia hyvin vähän. EKY-palveluhankintoihin onnistuttiin kuitenkin luomaan tasapainotettu mittaristo palvelujen erityispiirteet huomioiden. EKY-elinkaarikustannusanalysoinnissa keskityttiin palveluhankintojen keskeisiin kustannuskomponentteihin kuten transaktiokustannusteoriaan, hintojen määräytymiseen ja huonon laadun kustannuksiin. Näiden pohjalta kriittisiksi palveluhankintojen menestystekijöiksi nousivat mm. ostajien ajankäytön suuntaaminen strategisiin työtehtäviin, hintojen hallinta sekä toimittajien laadun arviointi. Nämä tekijät muotoiltiin EKY-palveluhankintojen tuloskorttiin ja niihin valittiin hankintatoimen mittausmalleista sopivat suorituskyvyn mittarit. Mittarit jaettiin EKY-palveluhankintoihin määriteltyihin neljään näkökulmaan Balanced Scorecard -prosessin mukaisesti.

Événements et déformations tardi-métamorphiques dans le segment Ossola-Ticino (Val Vigezzo-Centovalli, Italie-Suisse)

RESUME: Une zone tectonique large et complexe, connue sous le nom de ligne des Centovalli, traverse le secteur des Alpes Centrales compris entre Domodossola et Locarno. Cette région, formée par le Val Vigezzo et la vallée des Centovalli, constitue la terminaison méridionale du dôme Lepontin et représente une portion de la zone des racines des nappes alpines. Elle fait partie d’une grande et complexe zone de cisaillement, en partie associée à des phénomènes hydrothermaux d’âge alpin (<20 Ma), qui comprend le système tectonique Insubrien et celui du Simplon. Le Val Vigezzo et les Centovalli constituent un vrai carrefour entre les principaux accidents tectoniques des Alpes ainsi qu'une zone de juxtaposition du socle Sudalpin avec la zone des racines de l’Austroalpin et du Pennique. Les phases de déformation et les structures géologiques qui peuvent être étudiées s'étalent sur une période comprise entre environ 35 Ma et l'actuel. L’étude détaillée de terrain a mis en évidence la présence de nombreuses roches et structures de déformation de type ductile et cassant tels que des mylonites, des cataclasites, des pseudotachylites, des kakirites, des failles minéralisées, des gouges de faille et des plis. Sur le terrain on a pu distinguer au moins quatre générations de plis liés aux différentes phases de déformation. Le nombre et la complexité de ces structures indiquent une histoire très compliquée, selon plusieurs étapes distinctes, parfois liées, voire même superposées. Une partie de ces structures de déformation affectent aussi les dépôts sédimentaires d’âge quaternaire, notamment des limons et des sables lacustres. Ces sédiments constituent les restes d'un bassin lacustre attribué à l'époque interglaciaire Riss/Würm (éemien, 67.000-120.000 ans) et ils affleurent dans la partie centrale de la zone étudiée, à l'Est de la plaine de Santa Maria Maggiore. Ces sédiments montrent en leur sein toute une série de structures de déformation tels que des plans de faille inverses, des structures conjuguées de raccourcissement et des véritables plis. Ces failles et ces plis représenteraient les évidences de surface d’une déformation probablement active en époque quaternaire. Une autre formation rocheuse a retenu tout notre attention; il s'agit d'un corps de brèches péridotitiques monogéniques qui affleure en discontinuité le long du versant méridional et le long du fond de la vallée Vigezzo sur environ 20 km. Ces brèches se posent indifféremment sur le socle (unités Finero, Orselina) ou sur les sédiments lacustres. Elles sont traversées par des plans de failles qui développent des véritables stries de faille et des gouges de faille; l’orientation de ces plans est la même que celle affectant les failles à gouges du socle. La genèse de cette brèche est liée à l'altération et au modelage glacier (rock-glaciers) d'une brèche tectonique originelle qui borde la partie externe du Corps de Finero. Les structures de déformation de cette brèche, pareillement à celles des sédiments lacustres, ont été considérées comme les évidences de surface d'une tectonique quaternaire active dans la région. La dernière phase de déformation cassante qui affecte cette région peut donc être considérée comme active en époque quaternaire. Une vue d’ensemble de la région étudiée nous permet de reconnaître à l’échelle régionale une zone de cisaillement complexe orientée E-W, parallèlement à l’axe de la vallée Centovalli-Val Vigezzo. Les données de terrain, indiquent que cette zone de cisaillement débute sous conditions ductiles et évolue en plusieurs étapes jusqu’à des conditions de failles cassantes de surface. La reconstruction de l'évolution géodynamique de la région a permis de définir trois étapes distinctes qui marquent le passage, de ce secteur de socle cristallin, de conditions P-T profondes à des conditions de surface. Dans ce contexte, on a reconnu trois phases principales de déformation à l’échelle régionale qui caractérisent ces trois étapes. La phase la plus ancienne est constituée par des mylonites en faciès amphibolite, associées à des mouvements de cisaillement dextre, qui sont ensuite remplacés par des mylonites en faciès schistes verts et des plis rétrovergentes liés au rétrocharriage des nappes alpines. Une deuxième étape est identifiée par le développement d’une phase hydrothermale liée à un système de failles extensives et décrochantes dextres à direction principale E-W, NE-SW et NW-SE. Leur caractérisation minéralogique a permis la mise en évidence des phases cristallines de néoformation liées à cet événement constituées par : K-feldspath (microcline), chlorites (Fe+Mg), épidotes, prehnite, zéolites (laumontite), sphène, calcite. Dans ce contexte, pour obtenir une meilleure caractérisation de cet événement hydrothermal on a utilisé des géothermomètres sur chlorites, sensible aussi à la pression et a la a(H2O), qui ont donné des valeurs descendantes comprises entre 450-200°C. Les derniers mouvements sont mis en évidence par le développement d’une série de plans majeurs de failles à gouge, qui forment une structure en sigmoïdes d’épaisseur kilométrique reconnaissable à l’échelle de la vallée et caractérisée par des mouvements transpressifs avec une composante décrochante dextre toujours importante. Cette phase de déformation forme un système conjugué de failles avec direction moyenne E-W qui coupent la zone des racines des nappes alpines, la zone du Canavese et le corps ultramafique de Finero. Ce système se déroule de manière subparallèle à l'axe de la vallée le long de plusieurs dizaines de kilomètres. Une analyse complète et détaillée des gouges de faille par XRD a montré que la fraction argileuse (<2 µm) de ces gouges contient une partie de néoformation très importante constituée par, des illites, des chlorites et des interstratifiés de type illite/smectite ou chlorite/smectite. Des datations avec méthode K-Ar sur ces illites ont donné des valeurs comprises entre 12 et 4 Ma qui représentent l'âge de cette dernière déformation cassante. L'application de la méthode de la cristallinité de l'illite (C.I.) a permis d'évaluer les conditions thermiques qui caractérisent le déroulement de cette dernière phase tectonique qui se produit sous conditions de température caractéristiques de l'anchizone et de la diagenèse. L'ensemble des structures de déformation qu'on vient de décrire s'insère parfaitement dans le contexte de convergence oblique entre la plaque adriatique et celle européenne qui à produit l'orogène alpin. On peut considérer les structures tectoniques du Val Vigezzo-Centovalli comme l'expression d'une zone majeure de cisaillement "Simplo-Insubrienne". L'empilement structural et les structures tectoniques affleurantes dans la région sont le résultat de l'interaction entre un régime tectonique transpressif et un régime transtensif. Ces deux champs de tension sont antagonistes entre eux mais sont reliés, de toute façon, à une seule phase décrochante dextre principale, due à une convergence oblique entre deux plaques. À l'échelle de l'évolution géodynamique on peut distinguer différentes étapes au cours desquelles les structures de ces deux régimes tectoniques interagissent en manière différente. En accord avec les données géophysiques et les reconstructions paléodynamiques prises dans la littérature on considère que la ligne Rhône-Simplon-Centovalli représente l'évidence de surface de la suture majeure profonde entre la plaque Adriatique et celle Européenne. Les vitesses de soulèvement qui ont été calculées dans cette étude pour cette région des Alpes donnent une valeur moyenne de 0.8 mm/a qui est tout à fait comparable avec les données proposées par la littérature sur cette zone. La zone Val Vigezzo-Centovalli peut être donc considérée comme un carrefour géologique où se croisent différentes phases tectoniques qui représentent les évidences de surface d'une suture profonde majeure entre deux plaques dans un contexte de collision continentale. ABSTRACT: A wide and complex tectonic zone known as Centovalli line, crosses the Central Alps sector between Domodossola and Locarno. This area, formed by the Vigezzo Valley and Centovalli valley, constitutes the southernmost termination of the Lepontin dome and represents a portion of the alpine nappes root zone. It belongs to a large and complex shear-zone, partly associated with hydrothermal phenomena of alpine age (<20 My), which includes the Insubric Line and the Simplon fault zone. Vigezzo Valley and Centovalli constitute a real crossroads between the mains alpines tectonics lines as well as a zone of juxtaposition of the Southalpine basement with the Austroalpin and Pennique root zone. The deformation phases and the geological structures that can be studied between approximately 35 My and the present. The detailed field study showed the presence of many brittle and ductile deformation structures and fault rocks such as mylonites, cataclasites, pseudotachylites, kakirites, mineralized faults, fault gouges and folds. In the field we could distinguish at least four folds generations related to the various deformation phases. The number and the complexity of these structures indicate a very complicated history, comprising several different stages, that sometimes are related and even superimposed. Part of these deformation structures affect also the sedimentary deposits of quaternary age, in particular the silts and sands lake deposit. These sediments constitute the remainders of a lake basin ascribed to the interglacial Riss/Würm (Eemien, 67.000-120.000 years) and outcroping in the central part of the studied area, in the Eastern part of Santa Maria Maggiore plain. These sediments show a whole series of deformation structures such as inverse fault planes, combined shortening structures and true folds. These faults and folds would represent the surface evidence of a probably active tectonic deformation in quaternary time. Another rock formation attracted all our attention. It is a body of monogenic peridotite breccia which outcrops in discontinuity along the southernmost slope and the bottom of the Vigezzo valley on approximately 20 km. This breccia lies indifferently on the basement (Finero and Orselina units) or on the lake sediments. They are crossed by fault planes which developed slikenside and fault gouges whose orientation is the same of the faults gouges in the alpine basement. This breccia results from the weathering and the surface modelling of an original tectonic breccia which borders the external part of Finero peridotite body. This breccia deformation structures, like those of the lake sediments, were regarded as the surface interaction of active quaternary tectonics in the area. So the last brittle deformation phases which affects this area seems to be actives in quaternary time. Theoverall picture of the studied area on a regional scale enables us to point out a complex shear-zone directed E-W, parallel to the axis of the Centovalli and Vigezzo Valley. The field analysis indicates that this shear-zone began under ductile conditions and evolved in several stages to brittle faulting under surface conditions. The analysis of the geodynamic evolution of the area allows to define three different stages which mark the transition of this alpine basement root zone, from deep P-T conditions to P-T surface conditions. In this context on regional scale three principal deformation phases, which characterize these three stages can be distinguished. The oldest phase consisted of the amphibolitie facies mylonites, associated to dextral strikeslip movements. They are then replaced by green-schists facies mylonites and backfolds related to the backthrusting of the alpines nappes. A second episode is caracterized by the development of an hydrothermal phase bound to an extensive fault and dextral strike-slip fault system, with E-W, NW-SE and SE-NW principal directionsThe principal neoformed mineral phases related to this event are: K-feldspar (microcline), chlorites (Fe+Mg), epidotes prehnite, zéolites (laumontite), sphene and calcite. In this context, to obtain a better characterization of this hydrothermal event, we have used an chlorite geothermometer, sensitive also to the pressure and has the a(H2O), which gave downward values ranging between 450-200°C. The last movements are caracterized by the development of important gouge fault plans, which form a sigmoid structure of kilometric thickness which is recognizable at the valley scale, and is characterized by transpressive movements always with a significant dextral strike-slip component. This deformation phase forms a combined faults system with an average E-W direction, which cuts trough the alpine root zone, the Canavese zone and the Finero ultramafic body. This fault system takes place subparallel to the axis of the valley over several tens of kilometers. A complete and detailed XRD analysis of the gouges fault showed that the clay fraction (<2µm) contains a very significant neo-formation of illite, chlorites and mixed layered clays such as illite/smectite or chlorite/smectite. The K-Ar datings of the illite fraction <2µm gave values ranging between 12 and 4 My and the illite fraction <0.2µm gave more recents values until to 2,4-0 My.This values represent the age of this last brittle deformation. The application of the illite crystallinity method (C.I.) allowed evaluating the thermal conditions which characterize this tectonic phase that occured under temperature conditions of the anchizone and diagenesis. The whole set of deformation structures which we just described, perfectly fit the context of oblique convergence between the Adriatic and the European plate that produced the alpine orogen. We can regard the Vigezzo valley and Centovalli tectonic structures as the expression of a major "Simplo-Insubric" shear-zone. Structural stacking and tectonic structures that outcrop in the studied area, are the result of the interaction between a transpressive and a transtensve tectonic phases. These two tension fields are antagonistic but they are also connected, in any event, with only one principal dextral strike-slip movement, caused by an oblique convergence between two plates. On the geodynamic evolution scale we can distinguish various stages during which these two tectonic structures fields interact in various ways. In agreement with the geophysical data and the paleodynamic recostructions taken in the literature we considers that the Rhone-Simplon-Centovalli line are the surface feature of the major collision between the Adriatique and the European plate at depth. The uplift speeds we calculated in this study for this Alpine area give an average value of 0.8 mm/a, which is in good agreement with the data suggested by the literature on this zone. TheVigezzo Valley and Centovalli zone can therefore be regarded as a geological crossroad where various tectonic phases are superimposed. They represent the evidences of a major and deeper suture between two plates in a continental collision context.

Studies on integrating kinematic design method with mechanical systems simulation techniques

Theultimate goal of any research in the mechanism/kinematic/design area may be called predictive design, ie the optimisation of mechanism proportions in the design stage without requiring extensive life and wear testing. This is an ambitious goal and can be realised through development and refinement of numerical (computational) technology in order to facilitate the design analysis and optimisation of complex mechanisms, mechanical components and systems. As a part of the systematic design methodology this thesis concentrates on kinematic synthesis (kinematic design and analysis) methods in the mechanism synthesis process. The main task of kinematic design is to find all possible solutions in the form of structural parameters to accomplish the desired requirements of motion. Main formulations of kinematic design can be broadly divided to exact synthesis and approximate synthesis formulations. The exact synthesis formulation is based in solving n linear or nonlinear equations in n variables and the solutions for the problem areget by adopting closed form classical or modern algebraic solution methods or using numerical solution methods based on the polynomial continuation or homotopy. The approximate synthesis formulations is based on minimising the approximation error by direct optimisation The main drawbacks of exact synthesis formulationare: (ia) limitations of number of design specifications and (iia) failure in handling design constraints- especially inequality constraints. The main drawbacks of approximate synthesis formulations are: (ib) it is difficult to choose a proper initial linkage and (iib) it is hard to find more than one solution. Recentformulations in solving the approximate synthesis problem adopts polynomial continuation providing several solutions, but it can not handle inequality const-raints. Based on the practical design needs the mixed exact-approximate position synthesis with two exact and an unlimited number of approximate positions has also been developed. The solutions space is presented as a ground pivot map but thepole between the exact positions cannot be selected as a ground pivot. In this thesis the exact synthesis problem of planar mechanism is solved by generating all possible solutions for the optimisation process ¿ including solutions in positive dimensional solution sets - within inequality constraints of structural parameters. Through the literature research it is first shown that the algebraic and numerical solution methods ¿ used in the research area of computational kinematics ¿ are capable of solving non-parametric algebraic systems of n equations inn variables and cannot handle the singularities associated with positive-dimensional solution sets. In this thesis the problem of positive-dimensional solutionsets is solved adopting the main principles from mathematical research area of algebraic geometry in solving parametric ( in the mathematical sense that all parameter values are considered ¿ including the degenerate cases ¿ for which the system is solvable ) algebraic systems of n equations and at least n+1 variables.Adopting the developed solution method in solving the dyadic equations in direct polynomial form in two- to three-precision-points it has been algebraically proved and numerically demonstrated that the map of the ground pivots is ambiguousand that the singularities associated with positive-dimensional solution sets can be solved. The positive-dimensional solution sets associated with the poles might contain physically meaningful solutions in the form of optimal defectfree mechanisms. Traditionally the mechanism optimisation of hydraulically driven boommechanisms is done at early state of the design process. This will result in optimal component design rather than optimal system level design. Modern mechanismoptimisation at system level demands integration of kinematic design methods with mechanical system simulation techniques. In this thesis a new kinematic design method for hydraulically driven boom mechanism is developed and integrated in mechanical system simulation techniques. The developed kinematic design method is based on the combinations of two-precision-point formulation and on optimisation ( with mathematical programming techniques or adopting optimisation methods based on probability and statistics ) of substructures using calculated criteria from the system level response of multidegree-of-freedom mechanisms. Eg. by adopting the mixed exact-approximate position synthesis in direct optimisation (using mathematical programming techniques) with two exact positions and an unlimitednumber of approximate positions the drawbacks of (ia)-(iib) has been cancelled.The design principles of the developed method are based on the design-tree -approach of the mechanical systems and the design method ¿ in principle ¿ is capable of capturing the interrelationship between kinematic and dynamic synthesis simultaneously when the developed kinematic design method is integrated with the mechanical system simulation techniques.

Technology selection and group decision support systems: Case studies on supporting strategic technology selection processes

The objective of the dissertation is to increase understanding and knowledge in the field where group decision support system (GDSS) and technology selection research overlap in the strategic sense. The purpose is to develop pragmatic, unique and competent management practices and processes for strategic technology assessment and selection from the whole company's point of view. The combination of the GDSS and technology selection is approached from the points of view of the core competence concept, the lead user -method, and different technology types. In this research the aim is to find out how the GDSS contributes to the technology selection process, what aspects should be considered when selecting technologies to be developed or acquired, and what advantages and restrictions the GDSS has in the selection processes. These research objectives are discussed on the basis of experiences and findings in real life selection meetings. The research has been mainly carried outwith constructive, case study research methods. The study contributes novel ideas to the present knowledge and prior literature on the GDSS and technology selection arena. Academic and pragmatic research has been conducted in four areas: 1) the potential benefits of the group support system with the lead user -method,where the need assessment process is positioned as information gathering for the selection of wireless technology development projects; 2) integrated technology selection and core competencies management processes both in theory and in practice; 3) potential benefits of the group decision support system in the technology selection processes of different technology types; and 4) linkages between technology selection and R&D project selection in innovative product development networks. New type of knowledge and understanding has been created on the practical utilization of the GDSS in technology selection decisions. The study demonstrates that technology selection requires close cooperation between differentdepartments, functions, and strategic business units in order to gather the best knowledge for the decision making. The GDSS is proved to be an effective way to promote communication and co-operation between the selectors. The constructs developed in this study have been tested in many industry fields, for example in information and communication, forest, telecommunication, metal, software, and miscellaneous industries, as well as in non-profit organizations. The pragmatic results in these organizations are some of the most relevant proofs that confirm the scientific contribution of the study, according to the principles of the constructive research approach.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.

Introducing Basic Systematic Requirements Engineering Practices in Small Organizations with an Easy to Adopt Method

Requirements-relatedissues have been found the third most important risk factor in software projects and as the biggest reason for software project failures. This is not a surprise since; requirements engineering (RE) practices have been reported deficient inmore than 75% of all; enterprises. A problem analysis on small and low maturitysoftware organizations revealed two; central reasons for not starting process improvement efforts: lack of resources and uncertainty; about process improvementeffort paybacks.; In the constructive part of the study a basic RE method, BaRE, was developed to provide an; easy to adopt way to introduce basic systematic RE practices in small and low maturity; organizations. Based on diffusion of innovations literature, thirteen desirable characteristics; were identified for the solution and the method was implemented in five key components:; requirements document template, requirements development practices, requirements; management practices, tool support for requirements management, and training.; The empirical evaluation of the BaRE method was conducted in three industrial case studies. In; this evaluation, two companies established a completely new RE infrastructure following the; suggested practices while the third company conducted continued requirements document; template development based on the provided template and used it extensively in practice. The; real benefits of the adoption of the method were visible in the companies in four to six months; from the start of the evaluation project, and the two small companies in the project completed; their improvement efforts with an input equal to about one person month. The collected dataon; the case studies indicates that the companies implemented new practices with little adaptations; and little effort. Thus it can be concluded that the constructed BaRE method is indeed easy to; adopt and it can help introduce basic systematic RE practices in small organizations.

A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Grafting of quince 'Portugal' on Cydonia and Chaenomeles rootstocks

In the specific case of the quince trees, there is lack of information about the emergency of their seedlings, development and time of production of rootstocks to reach the point of the grafting, as well as development of the grafts. Therefore, the objective of the present research was to study the Cydonia and Chaenomeles genera, as well as the development of the grafts during the nursery phase. Seeds of the quince tree cultivars 'Mendoza Inta-37', 'Provence', ' Portugal' and 'Japonês' were obtained from ripe fruits and submitted to cold stratification during 20 days. Soon after, the seeds were sowed in 72-cell polystyrene trays (120 cm³ of capacity/cell) containing vermiculite as substrate. After 60 days, the seedlings were put in plastic bags (3 liters of capacity) filled with a substrate containing soil: sand: manure (1:1:1 v/v). The seedlings were kept in a 50% of shadow nursery and periodically irrigated. After 180 days, the seedlings were grafted by the cleft grafting method, during the winter, using scion sticks from quince 'Portugal'. After 60 days, the percentage of alive and sprouted grafts was evaluated. The length and diameter of the grafts were measured every 30 days, a total of four times. The quince 'Japonês' showed the best performance among all the rootstocks in this experiment, being an excellent alternative as rootstock for quince trees. 'Japonês' and 'Mendoza Inta-37' were also the rootstocks that promoted the best development of the grafts.

Use of the heat dissipation method for sap flow measurement in citrus nursery trees1

Sap flow could be used as physiological parameter to assist irrigation of screen house citrus nursery trees by continuous water consumption estimation. Herein we report a first set of results indicating the potential use of the heat dissipation method for sap flow measurement in containerized citrus nursery trees. 'Valencia' sweet orange [Citrus sinensis (L.) Osbeck] budded on 'Rangpur' lime (Citrus limonia Osbeck) was evaluated for 30 days during summer. Heat dissipation probes and thermocouple sensors were constructed with low-cost and easily available materials in order to improve accessibility of the method. Sap flow showed high correlation to air temperature inside the screen house. However, errors due to natural thermal gradient and plant tissue injuries affected measurement precision. Transpiration estimated by sap flow measurement was four times higher than gravimetric measurement. Improved micro-probes, adequate method calibration, and non-toxic insulating materials should be further investigated.

Lipid peroxidation and seed emergency in progenies of the yellow passion fruit plant

The objective was to evaluate the percentage of emergency plantlets and lipid peroxidation in seeds of 29 half-sib progenies of yellow passion fruit (Passiflora edulis Sims.) after 24 months under storage. The experimental design was completely randomized, with four replications of 50 seeds each, from which the treatments were the progenies (1-29). The evaluation of the percent plantlet emergency was accomplished at 14 and 28 days after sowing. The lipid peroxidation of the seeds was expressed as malondialdehyde (MDA) content that was determined by the TBARS method. Approximately 21% of those half-sib progenies maintained the viability of their seeds for twenty-four months under storage. The results point out a remarkable genetic variability for vigor and emergency of the yellow passion fruit plantlets, with occurrence of individuals with high and other ones with low capacity to maintaining the physiologic quality of their seeds after storage.

Procurement, Quality and Productivity Enhancements and Manufacturing Strategy Formulation Applying Product Life Cycle Method

The objective of the thesis was to create a framework that can be used to define a manufacturing strategy taking advantage of the product life cycle method, which enables PQP enhancements. The starting point was to study synkron implementation of cost leadership and differentiation strategies in different stages of the life cycles. It was soon observed that Porter’s strategies were too generic for the complex and dynamic environment where customer needs deviate market and product specifically. Therefore, the strategy formulation process is based on the Terry Hill’s order-winner and qualifier concepts. The manufacturing strategy formulation is initiated with the definition of order-winning and qualifying criteria. From these criteria there can be shaped product specific proposals for action and production site specific key manufacturing tasks that they need to answer in order to meet customers and markets needs. As a future research it is suggested that the process of capturing order-winners and qualifiers should be developed so that the process would be simple and streamlined at Wallac Oy. In addition, defined strategy process should be integrated to the PerkinElmer’s SGS process. SGS (Strategic Goal Setting) is one of the PerkinElmer’s core management processes. Full Text: Null