Seismic Wave Velocity as a Means of In-Place Density Measurement, Part 1, HR-114

Velocity-density tests conducted in the laboratory involved small 4-inch diameter by 4.58-inch-long compacted soil cylinders made up of 3 differing soil types and for varying degrees of density and moisture content, the latter being varied well beyond optimum moisture values. Seventeen specimens were tested, 9 with velocity determinations made along two elements of the cylinder, 180 degrees apart, and 8 along three elements, 120 degrees apart. Seismic energy was developed by blows of a small tack hammer on a 5/8-inch diameter steel ball placed at the center of the top of the cylinder, with the detector placed successively at four points spaced 1/2-inch apart on the side of the specimen involving wave travel paths varying from 3.36 inches to 4.66 inches in length. Time intervals were measured using a model 217 micro-seismic timer in both laboratory and field measurements. Forty blows of the hammer were required for each velocity determination, which amounted to 80 blows on 9 laboratory specimens and 120 blows on the remaining 8 cylinders. Thirty-five field tests were made over the three selected soil types, all fine-grained, using a 2-foot seismic line with hammer-impact points at 6-inch intervals. The small tack hammer and 5/8-inch steel ball was, again, used to develop seismic wave energy. Generally, the densities obtained from the velocity measurements were lower than those measured in the conventional field testing. Conclusions were reached that: (1) the method does not appear to be usable for measurement of density of essentially fine-grained soils when the moisture content greatly exceeds the optimum for compaction, and (2) due to a gradual reduction in velocity upon aging, apparently because of gradual absorption of pore water into the expandable interlayer region of the clay, the seismic test should be conducted immediately after soil compaction to obtain a meaningful velocity value.

A civil society response on the report of the UN High-Level Panel on system-wide coherence

Abordamos el Informe del Grupo de Alto Nivel sobre la Coherencia en todo el Sistema de las Naciones Unidas («Informe del Grupo») y el proceso de reforma de las Naciones Unidas del que forma parte como grupos de la sociedad civil que tienen una larga experiencia por lo que se refiere a propugnar reformas del sistema de las Naciones Unidas.

Analysis of Industrial Granular Flow Applications by Using Advanced Collision Models

Granular flow phenomena are frequently encountered in the design of process and industrial plants in the traditional fields of the chemical, nuclear and oil industries as well as in other activities such as food and materials handling. Multi-phase flow is one important branch of the granular flow. Granular materials have unusual kinds of behavior compared to normal materials, either solids or fluids. Although some of the characteristics are still not well-known yet, one thing is confirmed: the particle-particle interaction plays a key role in the dynamics of granular materials, especially for dense granular materials. At the beginning of this thesis, detailed illustration of developing two models for describing the interaction based on the results of finite-element simulation, dimension analysis and numerical simulation is presented. The first model is used to describing the normal collision of viscoelastic particles. Based on some existent models, more parameters are added to this model, which make the model predict the experimental results more accurately. The second model is used for oblique collision, which include the effects from tangential velocity, angular velocity and surface friction based on Coulomb's law. The theoretical predictions of this model are in agreement with those by finite-element simulation. I n the latter chapters of this thesis, the models are used to predict industrial granular flow and the agreement between the simulations and experiments also shows the validation of the new model. The first case presents the simulation of granular flow passing over a circular obstacle. The simulations successfully predict the existence of a parabolic steady layer and show how the characteristics of the particles, such as coefficients of restitution and surface friction affect the separation results. The second case is a spinning container filled with granular material. Employing the previous models, the simulation could also reproduce experimentally observed phenomena, such as a depression in the center of a high frequency rotation. The third application is about gas-solid mixed flow in a vertically vibrated device. Gas phase motion is added to coherence with the particle motion. The governing equations of the gas phase are solved by using the Large eddy simulation (LES) and particle motion is predicted by using the Lagrangian method. The simulation predicted some pattern formation reported by experiment.

Poisoning effect of s on pd surfaces

In this study we observe the poisoning effect of S to the adsorption and dissociation of 02 molecule on Pd surfaces. To perform this study we used Viennaab initio Simulation Package (VASP) and Spanish Initiative for Electronic structure with thousands of Atoms (SIESTA) ab initio softwares. To describe all Pd surfaces we selected the (100), and (211) surfaces, because we need very reactive and simple surfaces. Before studying the poison¬ing effect of S we had to study the dissociation of 02 on the surfaces. We discovered that on the (100) surface the hollow site is the most reactive site, but at room temperature the steric hinderace effect occurs very easily. If the molecule has enough vibrational energyit will dissociate. On the (211) surface the (100) micro facet's hollow site is the most reactive site and the molecule dissociates in the site without any barrier, and the molecule drifts from the terrace to this site. An S atom sticks on the Pd (100) surface in the hollow site. It affects the d-band density of states of the nearests Pd atoms; It moves the center of the d-band downin energy, when the bond between the Pd atom and the 0 atom is more antibonding. In the hollow site the S atom also blocks the dissociation site of the molecule. On the Pd(211) surface the energetically favourable site of the S atom is the(100) microfacet's hollow site. There it blocks the most reactive site, but its effect to the Pd atoms next to it is not significant.

Colloid cysts of the third ventricle: correlation of MR and CT findings with histology and chemical analysis.

Eight patients with colloid cysts of the third ventricle were examined with CT and MR. In six, surgical resection was performed and the material was subjected to histologic evaluation; the concentrations of trace elements were determined by particle-induced X-ray emission. Stereotaxic aspiration was performed in two. The investigation showed that colloid cysts are often iso- or hypodense relative to brain on CT (5/8), but sometimes have a center of increased density. Increased density did not correlate with increased concentration of calcium or other metals but did not correlate with high cholesterol content. Colloid cysts appear more heterogeneous on MR (6/8) than on CT (3/8), despite a homogeneous appearance at histology. High signal on short TR/TE sequences is correlated with a high cholesterol content. A marked shortening of the T2 relaxation time is often noticed in the central part of the cyst. Analysis of trace elements showed that this phenomenon is not related to the presence of metals with paramagnetic effects. Our analysis of the contents of colloid cysts does not support the theory that differing metallic concentrations are responsible for differences in MR signal intensity or CT density. We did find that increased CT density and high MR signal correlated with high cholesterol content.

Coordination pattern adaptability: energy cost of degenerate behaviors.

This study investigated behavioral adaptability, which could be defined as a blend between stability and flexibility of the limbs movement and their inter-limb coordination, when individuals received informational constraints. Seven expert breaststroke swimmers performed three 200-m in breaststroke at constant submaximal intensity. Each trial was performed randomly in a different coordination pattern: 'freely-chosen', 'maximal glide' and 'minimal glide'. Two underwater and four aerial cameras enabled 3D movement analysis in order to assess elbow and knee angles, elbow-knee pair coordination, intra-cyclic velocity variations of the center of mass, stroke rate and stroke length and inter-limb coordination. The energy cost of locomotion was calculated from gas exchanges and blood lactate concentration. The results showed significantly higher glide, intra-cyclic velocity variations and energy cost under 'maximal glide' compared to 'freely-chosen' instructional conditions, as well as higher reorganization of limb movement and inter-limb coordination (p<0.05). In the 'minimal glide' condition, the swimmers did not show significantly shorter glide and lower energy cost, but they exhibited significantly lower deceleration of the center of mass, as well as modified limb movement and inter-limb coordination (p<0.05). These results highlight that a variety of structural adaptations can functionally satisfy the task-goal.

Development of fluid conduits in the auriferous shear zones of the Hutti Gold Mine, India: evidence for spatially and temporally heterogeneous fluid flow

The gold mineralization of the Hutti Mine is hosted by nine parallel, N - S trending, steeply dipping, 2 - 10 m wide shear zones, that transect Archaean amphibolites. The shear zones were formed after peak metamorphism during retrograde ductile D, shearing in the lower amphibolite facies. They were reactivated in the lower to mid greenschist facies by brittle-ductile D-3 shearing and intense quartz veining. The development of a S-2-S-3 crenulation cleavage facilitates the discrimination between the two deformation events and contemporaneous alteration and gold mineralization. Ductile D, shearing is associated with a pervasively developed distal chlorite - sed cite alteration assemblage in the outer parts of the shear zones and the proximal biotite-plagioclase alteration in the center of the shear zones. D3 is characterized by development of the inner chlorite-K-feldspar alteration, which forms a centimeter-scale alteration halo surrounding the laminated quartz veins and replaces earlier biotite along S-3. The average size of the laminated vein systems is 30-50 m along strike as well as down-dip and 2-6 m in width. Mass balance calculations suggest strong metasomatic changes for the proximal biotite-plagioclase alteration yielding mass and volume increase of ca. 16% and 12%, respectively. The calculated mass and volume changes of the distal chlorite-sericite alteration (ca. 11%, ca. 8%) are lower. The decrease in 6180 values of the whole rock from around 7.5 parts per thousand for the host rocks to 6-7 parts per thousand for the distal chlorite-sericite and the proximal biotite-plagioclase alteration and around 5 parts per thousand for the inner chlorite-K-feldspar alteration suggests hydrothermal alteration during two-stage deformation and fluid flow. The ductile D-2 deformation in the lower amphibolite facies has provided grain scale porosities by microfracturing. The pervasive, steady-state fluid flow resulted in a disseminated style of gold-sulfide mineralization and a penetrative alteration of the host rocks. Alternating ductile and brittle D3 deformation during lower to mid greenschist facies conditions followed the fault-valve process. Ductile creep in the shear zones resulted in a low permeability environment leading to fluid pressure build-up. Strongly episodic fluid advection and mass transfer was controlled by repeated seismic fracturing during the formation of laminated quartz(-gold) veins. The limitation of quartz veins to the extent of earlier shear zones indicate the importance of preexisting anisotropies for fault-valve action and economic gold mineralization. (C) 2003 Elsevier B.V. All rights reserved.

The effects of productivity on profitability: a case study at firm level using an activity-based costing approach

Productivity and profitability are important concepts and measures describing the performance and success of a firm. We know that increase in productivity decreases the costs per unit produced and leads to better profitability. This common knowledge is not, however, enough in the modern business environment. Productivity improvement is one means among others for increasing the profitability of actions. There are many means to increase productivity. The use of these means presupposes operative decisions and these decisions presuppose informationabout the effects of these means. Productivity improvement actions are in general made at floor level with machines, cells, activities and human beings. Profitability is most meaningful at the level of the whole firm. It has been very difficult or even impossible to analyze closely enough the economical aspects of thechanges at floor level with the traditional costing systems. New ideas in accounting have only recently brought in elements which make it possible to considerthese phenomena where they actually happen. The aim of this study is to supportthe selection of objects to productivity improvement, and to develop a method to analyze the effects of the productivity change in an activity on the profitability of a firm. A framework for systemizing the economical management of productivity improvement is developed in this study. This framework is a systematical way with two stages to analyze the effects of productivity improvement actions inan activity on the profitability of a firm. At the first stage of the framework, a simple selection method which is based on the worth, possibility and the necessity of the improvement actions in each activity is presented. This method is called Urgency Analysis. In the second stage it is analyzed how much a certain change of productivity in an activity affects the profitability of a firm. A theoretical calculation model with which it is possible to analyze the effects of a productivity improvement in monetary values is presented. On the basis of this theoretical model a tool is made for the analysis at the firm level. The usefulness of this framework was empirically tested with the data of the profit center of one medium size Finnish firm which operates in metal industry. It is expressedthat the framework provides valuable information about the economical effects of productivity improvement for supporting the management in their decision making.

Environmental requirements and environmental management system of boiler plant supplier

Työn tärkeimpänä tavoitteena oli edistää ympäristöjärjestelmän laatimista Kvaerner Pulping, Power divisioonan Kattilat-liiketoimintayksikölle. Lisäksi tavoitteena oli tarkastella yritykseen kohdistuvia ympäristövaatimuksia ja niiden vaikutusta yrityksen toimintaan. Aluksi työssä tarkasteltiin ympäristöjärjestelmästandardien sisältöjä ja niiden eroja. Työssä käsiteltiin myös erilaisia elinkaarijohtamisen malleja, joita voidaan hyödyntää yrityksen kokonaisvaltaisessa ympäristöjärjestelmässä. Työssä tarkasteltiin myös sidosryhmien vaikutusta yrityksen ympäristötoimintaan. Kattilalaitostoimittajan tärkeimpiä asiakkaita ovat sellu- ja paperiteollisuus. Näihin yrityksiin on kohdistunut runsaan kymmenen vuoden aikana paineita ympäristötoiminnan tehostamiseksi. Tämän kehityksen seurauksena vastaavat tehostamispaineet ovat siirtymässä myös alihankkijoille, kuten kattilaitostoimittajille. Tehokkaan ympäristöjohtamisen takaamiseksi työssä määriteltiin ympäristövastuut ja –valtuudet sekä ympäristöpäämäärät ja –tavoitteet. Lisäksi tunnistettiin yrityksen toimintaan liittyvät ympäristönäkökohdat ja –riskit. Työn yhteydessä laadittiin ympäristöjärjestelmän luonnos, ja se sisältää jatkuvan parantamisen periaatteen. Työn yhteydessä laadittiin lisäksi Kvaerner Pulping Oy:n koelaitokselle ympäristölupahakemus. Työssä on kuvattu koelaitosta ja sen ympäristölupahakemukseen liittyviä asioita esimerkkinä parantuneesta ympäristöasioiden hoidosta.

Design, implementation and testing of DVB/MHP-application development environment

Tämä diplomityö esittelee 1.6. - 4.11.2002 Mikkelin ammattikorkeakoulun YTI-tutkimuskeskuksen Informaatio- ja mediateknologian hankekokonaisuuden STRIMT-projektin puitteissa tekemäni MHP-kehitysjärjestelmähankinnan tuloksia. Digitaalitelevision MHP-sovelluskehitysjärjestelmän hankinnan tulosten lisäksi työ antaa yleiskuvan MHP-sovelluskehitystyökaluista, digitaalitelevisiostandardeista sekä digitaalitelevisioverkkojen yhteistoimintamalleista televerkkojen kanssa. Keräämieni tietojen, tekemäni tarvemäärittelyn ja suorittamani tuotevertailun perusteella valitsin tarpeisiimme sopivimmaksi järjestelmäksi Alticast Inc.-yrityksen Altifusion-tuotteen. Tuotteen valinnassa otin huomioon myös mahdolliset tulevaisuuden tarpeet aina täysimittaista lähetysjärjestelmää varten kehittämällä vaiheittaisen hankintasuunnitelman. Järjestelmää hankittaessa tärkeintä on huomioida heti alusta alkaen mahdolliset tulevat tarpeet ja varmistaa hankinnan hyödynnettävyys myös tulevaisuudessa. Järjestelmän hankinnan lisäksi vastasin sen käyttöönotosta ja järjestelmää hyödyntävän testisovelluksen laatimisesta.

Spatial mapping of exciton lifetimes in single ZnO nanowires

We investigate the spatial dependence of the exciton lifetimes in single ZnO nanowires. We have found that the free exciton and bound exciton lifetimes exhibit a maximum at the center of nanowires, while they decrease by 30% towards the tips. This dependence is explained by considering the cavity-like properties of the nanowires in combination with the Purcell effect. We show that the lifetime of the bound-excitons scales with the localization energy to the power of 3/2, which validates the model of Rashba and Gurgenishvili at the nanoscale.

Fluid dynamical prediction of changed v1-flow at energies available at the CERN Large Hadron Collider

Substantial collective flow is observed in collisions between lead nuclei at Large Hadron Collider (LHC) as evidenced by the azimuthal correlations in the transverse momentum distributions of the produced particles. Our calculations indicate that the global v1-flow, which at RHIC peaked at negative rapidities (named third flow component or antiflow), now at LHC is going to turn toward forward rapidities (to the same side and direction as the projectile residue). Potentially this can provide a sensitive barometer to estimate the pressure and transport properties of the quark-gluon plasma. Our calculations also take into account the initial state center-of-mass rapidity fluctuations, and demonstrate that these are crucial for v1 simulations. In order to better study the transverse momentum flow dependence we suggest a new"symmetrized" vS1(pt) function, and we also propose a new method to disentangle global v1 flow from the contribution generated by the random fluctuations in the initial state. This will enhance the possibilities of studying the collective Global v1 flow both at the STAR Beam Energy Scan program and at LHC.

Performance Management of a Next Generation Network

Today's communication networks consist of numerous interdependent network components. To manage these networks and to ensure their reliable and efficient operation to meet the increasing customer usability demands, extensive network management tools are required from the service provider. The goal of this study was to adapt the Next Generation Network (NGN) providing VoIP services within a performance oriented network management system. This study focuses only on NGN network and the project was implemented as an assignment of the Network Operations Center of Elisa Corporation. The theoretical part of this study introduces the network environment of the Elisa NGN platform: its components and used signalling protocols as well as other exploitable communication protocols. In addition, the Simple Network Management Protocol (SNMP) is closely examined since it is commonly used as the basis of IP (Internet Protocol) network management. Also some primary applications enabled by the NGN technology are introduced. The empirical part of this study contains a short overview of the implemented network performance management system and its properties. The most crucial monitored MIB modules, SNMP parameters and implemented performance measurements are described. The trap topology and the role of the traps for management of the NGN platform are considered and finally, the conclusion based on the several disquisitions is made supported with suggestions for future improvements.