GROWTH OF HIGH-QUALITY GALLIUM-ARSENIDE ON HF-ETCHED SILICON (001) BY CHEMICAL BEAM EPITAXY

HF etching followed by relatively low temperature (almost-equal-to 600-degrees-C) pretreatment is shown to provide a suitable substrate for the heteroepitaxial growth of GaAs on Si(100) by CBE using TEGa and AsH3 as sources. Rutherford backscattering (RBS), photoluminescence (PL), transmission electron microscopy (TEM), and Raman measurements show the low-defect nature of the GaAs epilayer.

Theoretical and experimental investigations of flexural wave propagation in periodic grid structures designed with the idea of phononic crystals

The propagation characteristics of fiexural waves in periodic grid structures designed with the idea of phononic crystals are investigated by combining the Bloch theorem with the finite element method. This combined analysis yields phase constant surfaces, which predict the location and the extension of band gaps, as well as the directions and the regions of wave propagation at assigned frequencies. The predictions are validated by computation and experimental analysis of the harmonic responses of a finite structure with 11 × 11 unit cells. The fiexural wave is localized at the point of excitation in band gaps, while the directional behaviour occurs at particular frequencies in pass bands. These studies provide guidelines to designing periodic structures for vibration attenuation.

HCl/HF/CrO3溶液对 InGaAs/InGaAsP的选择性湿法刻蚀--应用于楔形结构的制备

利用动态掩膜湿法腐蚀技术,研究了HCl/HF/CrO3溶液对与InP衬底晶格匹配的InxGa1-xAs1-yPy(y=0,0.2,0.4,0.6)材料的腐蚀特性.对于HCl(36wt%)/HF(40wt%)/CrO3(10wt%)的体积比为x∶0.5∶1的溶液,随着x由0增加到1.25,相应的腐蚀液对In0.53Ga0.47As/In0.72Ga0 28As06P0.4的选择性由42.4降到1.4;通过调节腐蚀液的选择性,在In072Ga0.28As06P0.4外延层上制备出了倾角从1.35°到35.9°的各种楔形结构;当x为0.025和1.25时,相应的In0.72Ga0.28As0.6P0.4腐蚀表面的均方根粗糙度分别为1.1nm和1.6nm.还研究了溶液的组分与InxGa1-xAs1-yPy(y=0,0.2,0.4)的腐蚀速率间的关系,并对腐蚀机理进行了分析.

HF/CrO_3溶液对AlGaAs的选择性湿法刻蚀应用于楔型结构的制备

利用动态掩膜腐蚀技术，研究了HF/CrO_3腐蚀液对各种不同组分的Al_xGa_(1-x)As (x = 0.3, 0.5, 0.65)的腐蚀速率及腐蚀表面形貌。随着HF(48wt%)/CrO_3(33wt%)的体积比由0.01变化到0.138，相应的腐蚀液对Al_(0.8)Ga_(0.2)As/Al_(0.3)Ga_(0.7)As的选择性由179降到8.6；通过调节腐蚀液的选择性，在Al_(0.3)Ga_(0.7)As外延层上制备出了倾角从0.32°到6.61°的各种斜面。当HF(48wt%)/CrO_3(33wt%)的体积比为0.028时，Al组分分别为0.3、0.5和0.65时，相应的腐蚀表面的均方根粗糙度为1.8、9.1和19.3nm。另外，还分析了腐蚀机理与腐蚀表面形貌之间的关系。

etl workflow analysis and verification using backwards constraint propagation

University of Twente; Centre for Telematics and Information Technology; Netherlands Organisation for Scientific Research; Jacquard; Capgemini

Intercellular calcium wave propagation in linear and circuit-like bone cell networks

In the present study, the mechanism of intercellular calcium wave propagation in bone cell networks was identified. By using micro-contact printing and self-assembled monolayer technologies, two types of in vitro bone cell networks were constructed: open-ended linear chains and looped hexagonal networks with precisely controlled intercellular distances. Intracellular calcium responses of the cells were recorded and analysed when a single cell in the network was mechanically stimulated by nano-indentation. The looped cell network was shown to be more efficient than the linear pattern in transferring calcium signals from cell to cell. This phenomenon was further examined by pathway-inhibition studies. Intercellular calcium wave propagation was significantly impeded when extracellular adenosine triphosphate (ATP) in the medium was hydrolysed. Chemical uncoupling of gap junctions, however, did not significantly decrease the transferred distance of the calcium wave in the cell networks. Thus, it is extracellular ATP diffusion, rather than molecular transport through gap junctions, that dominantly mediates the transmission of mechanically elicited intercellular calcium waves in bone cells. The inhibition studies also demonstrated that the mechanical stimulation-induced calcium responses required extracellular calcium influx, whereas the ATP-elicited calcium wave relied on calcium release from the calcium store of the endoplasmic reticulum.

Experimental Setup for Assessing the Energetic Materials Deflagration Propagation under High Temperature and High Pressure Conditions

The technology of "explosion in fractures" is one of new synthetic engineering methods used in low permeability reservoirs. The most important problem arose from the technology is to assess the deflagration propagation capability of milky explosives in rock fractures. In order to investigate detailed this problem in the laboratory, an experimental setup was designed and developed in which different conditions can be simulated. The experimental setup mainly includes two parts. One is the experimental part and the other is the measurement part. In the experimental setup, the narrow slots with different width can be simulated; meanwhile, different initial pressures and initial temperatures can be loaded on the explosives inside the narrow slots. The initial pressure range is from 0-60 MPa, and the initial temperatures range is from room temperature to 100 V. The temperature and the velocity of deflagration wave can be measured; meanwhile the corresponding pressure in the narrow slot is also measured. In the end, some typical measurement results are briefly presented and discussed.

Study on peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles

The on-way peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles are important data for process safety. Based on carbon monoxide deflagration experiments, the paper presents a multi-zone integration model for calculation of on-way peak overpressure, in which the tube with obstacles is considered as a series of venting explosion enclosures which link each others. The analysis of experimental data indicates that the on-way peak overpressure of gas deflagration can be correlated as an empirical formula with equivalence ratio of carbon monoxide oxidation, expansion ratio, flame path length, etc., and that the on-way peak overpressure exhibits a linear relationship with turbulence factor and flame propagation speed. An empirical formula of flame propagation speed is given.

Hf同位素新衰变γ射线的观测

利用14MeV中子轰击天然钨靶,通过180,182,183,184,186W(n,2pxn)反应,产生铪的放射性同位素,以γ(X)谱学方法鉴别出铪,观测到了能量为75.2keV和88.7keV的2条新γ射线,测定其半衰期为(3.6±0.6)min。

An efficient in vitro method for mass propagation of Potentilla potaninii wolf

This study reports a method for high-frequency shoot organogenesis and plant establishment of Potentilla potaninii Wolf. Hypocotyl and cotyledon explants of P. potaninii were cultured on Murashige and Skoog (MS) medium supplemented with various concentrations of benzyladenine (BA) and alpha-naphthaleneacetic acid (NAA) to induce adventitious shoot formation for micropropagation. The highest frequency of adventitious shoot regeneration was achieved from hypocotyl and cotyledon explants grown on MS medium supplemented with 5.0 mg l(-1) BA and 1.0 mg l(-1) NAA. The regenerated shoots rooted most efficiently on half-strength MS medium supplemented with 1.0 mg l(-1) NAA and 0.5 mg l(-1) indole-3-acetic acid or indole-3-butyric acid. The acclimatized plants with normal morphology and growth characters flowered and set seeds in the following year.