Surface engineering of reduced graphene oxide for controllable ambipolar flash memories

Tunable charge-trapping behaviors including unipolar charge trapping of one type of charge carrier and ambipolar trapping of both electrons and holes in a complementary manner is highly desirable for low power consumption multibit flash memory design. Here, we adopt a strategy of tuning the Fermi level of reduced graphene oxide (rGO) through self-assembled monolayer (SAM) functionalization and form p-type and n-type doped rGO with a wide range of manipulation on work function. The functionalized rGO can act as charge-trapping layer in ambipolar flash memories, and a dramatic transition of charging behavior from unipolar trapping of electrons to ambipolar trapping and eventually to unipolar trapping of holes was achieved. Adjustable hole/electron injection barriers induce controllable Vth shift in the memory transistor after programming operation. Finally, we transfer the ambipolar memory on flexible substrates and study their charge-trapping properties at various bending cycles. The SAM-functionalized rGO can be a promising candidate for next-generation nonvolatile memories.

Environments for zonal cartilage tissue engineering

Articular cartilage is a highly organized tissue with cellular and matrix properties that vary with depth zones. Regenerating this zonal organization has proven difficult in tissue-engineered cartilage to treat damaged cartilage. In this thesis, we evaluated the effects of culture environments that mimic aspects of the native cartilage environment on chondrocyte subpopulations. We found that decellularized cartilage matrix can improve zonal tissue-engineered cartilage. Also, chondrocytes respond to signals from bone cells and compressive stimulation in a zone-dependent manner. These results highlight the importance of a zone-specific environment to improve tissue-engineered cartilage in vitro.

Science, Technology, Engineering, and Maths (STEM)

"Historically, science had a place in education before the time of Plato and Aristotle (e.g., Stonehenge). Technology gradually increased since early human inventions (e.g., indigenous tools and weapons), rose up dramatically through the industrial revolution and escalated exponentially during the twentieth and twenty-first centuries, particularly with the advent of the Internet. Engineering accomplishments were evident in the constructs of early civil works, including roads and structural feats such as the Egyptian pyramids. Mathematics was not as clearly defined BC (Seeds 2010), but was utilized for more than two millennia (e.g., Archimedes, Kepler, and Newton) and paved its way into education as an essential scientific tool and a way of discovering new possibilities. Hence, combining science, technology, engineering, and mathematics (STEM) areas should not come as a surprise but rather as a unique way of packaging what has been ..."--Publisher Website

Teaching manufacturing engineering at tertiary institutions in conjunction with engineering design and engineering materials

Tertiary institutions now face serious challenges. Modern industry requires engineering graduates with strong knowledge of modern technologies, highly practical focus, management skills, ability to work individually and in a team, understanding of environmental issues and many other skills and graduate attributes. Institutions in the tertiary sector change courses and modify curriculum to reflect challenges of the modern industry and make engineering graduates better prepared for the “real world”. Queensland University of Technology in the recent years introduced an innovative structure of engineering courses with a common core for Bachelor of Engineering Mechanical, Infomechatronics and Medical, where manufacturing is taught in conjunction with engineering design and engineering materials. In this paper we discuss the innovative curriculum structure, teaching and learning approaches of coherent delivery of manufacturing in conjunction with engineering design and

Driving toward user-centered engineering in automotive design

In an industry worth more than €500 billion annually, producing more than 80 million vehicles worldwide each year and consisting of over 50 major manufacturers worldwide, the automotive industry represents a lucrative but highly competitive manufacturing industry (Deloitte, 2009a; European Automobile Manufacturers Association, 2012). With sales falling in Europe in 2013 for the sixth consecutive year (Boston and Curtin, 2014), automotive manufacturers are increasingly turning to new strategies to retain their share of sales in a contracting market. Some strategies have focused on the industry approach to manufacturing, namely, a technically focused push for a build-toorder process rather than the current build-to-stock approach in order to reduce overall value-chain costs and to increase efficiency (Parry and Roehrich, 2013, p. 13). However, others stress a more customer-orientated approach, striving to develop products that meet customer requirements (Oliver Wyman Group, 2007).

First-principle engineering magnetism in low-dimensional boron nitride materials

Nanotubes and nanosheets are low-dimensional nanomaterials with unique properties that can be exploited for numerous applications. This book offers a complete overview of their structure, properties, development, modeling approaches, and practical use. It focuses attention on boron nitride (BN) nanotubes, which have had major interest given their special high-temperature properties, as well as graphene nanosheets, BN nanosheets, and metal oxide nanosheets. Key topics include surface functionalization of nanotubes for composite applications, wetting property changes for biocompatible environments, and graphene for energy storage applications

Copula-based spatial modelling of geometallurgical variables

The most important aspect of modelling a geological variable, such as metal grade, is the spatial correlation. Spatial correlation describes the relationship between realisations of a geological variable sampled at different locations. Any method for spatially modelling such a variable should be capable of accurately estimating the true spatial correlation. Conventional kriged models are the most commonly used in mining for estimating grade or other variables at unsampled locations, and these models use the variogram or covariance function to model the spatial correlations in the process of estimation. However, this usage assumes the relationships of the observations of the variable of interest at nearby locations are only influenced by the vector distance between the locations. This means that these models assume linear spatial correlation of grade. In reality, the relationship with an observation of grade at a nearby location may be influenced by both distance between the locations and the value of the observations (ie non-linear spatial correlation, such as may exist for variables of interest in geometallurgy). Hence this may lead to inaccurate estimation of the ore reserve if a kriged model is used for estimating grade of unsampled locations when nonlinear spatial correlation is present. Copula-based methods, which are widely used in financial and actuarial modelling to quantify the non-linear dependence structures, may offer a solution. This method was introduced by Bárdossy and Li (2008) to geostatistical modelling to quantify the non-linear spatial dependence structure in a groundwater quality measurement network. Their copula-based spatial modelling is applied in this research paper to estimate the grade of 3D blocks. Furthermore, real-world mining data is used to validate this model. These copula-based grade estimates are compared with the results of conventional ordinary and lognormal kriging to present the reliability of this method.

Tectonometamorphic evolution of the Åreskutan Nappe-Caledonian history revealed by SIMS U–Pb zircon geochronology

Secondary ionization mass spectrometry (SIMS) U–Pb dating of zircons from the Åreskutan Nappe in the central part of the Seve Nappe Complex of western central Jämtland provides new constraints on the timing of granulite–amphibolite-facies metamorphism and tectonic stacking of the nappe during the Caledonian orogeny. Peak-temperature metamorphism in garnet migmatites is constrained to c. 442 ± 4 Ma, very similar to the ages of leucogranites at 442 ± 3 and 441 ± 4 Ma. Within a migmatitic amphibolite, felsic segregations crystallized at 436 ± 2 Ma. Pegmatites, cross-cutting the dominant Caledonian foliation in the Nappe, yield 428 ± 4 and 430 ± 3 Ma ages. The detrital zircon cores in the migmatites and leucogranites provide evidence of Late Palaeoproterozoic, Mesoproterozoic to Early Neoproterozoic source terranes for the metasedimentary rocks. The formation of the ductile and hot Seve migmatites, with their inverted metamorphism and thinning towards the hinterland, can be explained by an extrusion model in which the allochthon stayed ductile for a period of at least 10 million years during cooling from peak-temperature metamorphism early in the Silurian. In our model, Baltica–Laurentia collision occurred in the Late Ordovician–earliest Silurian, with emplacement of the nappes far on to the Baltoscandian platform during the Silurian and early Devonian, Scandian Orogeny lasting until c. 390 Ma.

Preparing engineering graduates for the knowledge economy through blended delivery of mathematics

Contemporary higher education institutions are making significant efforts to develop cohesive, meaningful and effective learning experiences for Science, Technology, Engineering and Mathematics (STEM) curricula to prepare graduates for challenges in the modern knowledge economy, thus enhancing their employability (Carnevale et al, 2011). This can inspire innovative redesign of learning experiences embedded in technology-enhanced educational environments and the development of research-informed, pedagogically reliable strategies fostering interactions between various agents of the learning-teaching process. This paper reports on the results of a project aimed at enhancing students’ learning experiences by redesigning a large, first year mathematics unit for Engineering students at a large metropolitan public university. Within the project, the current study investigates the effectiveness of selected, technology-mediated pedagogical approaches used over three semesters. Grounded in user-centred instructional design, the pedagogical approaches explored the opportunities for learning created by designing an environment containing technological, social and educational affordances. A qualitative analysis of mixed-type questionnaires distributed to students indicated important inter-relations between participants’ frames of references of the learning-teaching process and stressed the importance (and difficulty) of creating appropriate functional context. Conclusions drawn from this study may inform instructional design for blended delivery of STEM-focused programs that endeavor to enhance students’ employability by educating work-ready graduates.

Additive tissue manufacturing for breast reconstruction: Combining CAD/CAM with adipose tissue engineering

The primary aim of this multidisciplinary project was to develop a new generation of breast implants. Disrupting the currently prevailing paradigm of silicone implants which permanently introduce a foreign body into mastectomy patients, highly porous implants developed as part of this PhD project are biodegradable by the body and augment the growth of natural tissue. Our technology platform leverages computer-assisted-design which allows us to manufacture fully patient-specific implants based on a personalised medicine approach. Multiple animal studies conducted in this project have shown that the polymeric implant slowly degrades within the body harmlessly while the body's own tissue forms concurrently.

User centred engineering in automotive design: A shift from technology-driven product development

The research assessed how best to transition engineering-based automotive firms towards more customer-orientated design and development approaches, whilst identifying the main barriers and concerns facing such a shift. The research investigates the ability of a firm to empower individual engineers with user centred design tools traditionally used by designers, whilst understanding the company-wide needs to facilitate their implementation.

Tissue engineering of a morphologically and functionally intact humanized bone organ for bone metastasis research

The aim of this thesis was to establish an individualized, patient-specific diagnostic and therapeutic preclinical disease model for bone metastasis research. Tissue engineering of humanized bone within mice allowed the development of a humanized immune system in the host animal. This novel platform makes it possible to analyze the growth of human cancer cells in human bone in the presence of human immune cells.

Cyclic Salinity Model for deposition of large-scale coal deposits

Existing field data for Rangal coals (Late Permian) of the Bowen Basin, Queensland, Australia, are inconsistent with the depositional model generally accepted in the current geological literature to explain coal deposition. Given the apparent unsuitability of the current depositional model to the Bowen Basin coal data, a new depositional model, here named the Cyclic Salinity Model, is proposed and tested in this study.

Eruption centres of the Hamilton area of the Newer Volcanics Province, Victoria, Australia: Pinpointing volcanoes from a multifaceted approach to landform mapping

Volcanic eruption centres of the mostly 4.5 Ma-5000 BP Newer Volcanics Province in the Hamilton area of southeastern Australia were examined in detail using a multifaceted approach, including ground truthing and analysis of ArcGIS Total Magnetic Intensity and seamless geology data, NASA Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) digital elevation models and Google Earth satellite image interpretation. Sixteen eruption centres were recognised in the Hamilton area, including three previously unrecorded volcanoes-one of which, the Cas Maar, constitutes the northernmost maar-cone volcanic complex in the Western Plains subprovince. Seven previously allocated eruption centres were placed into question based on field and laboratory observations. Three phases of volcanic activity have been suggested by other authors and are interpreted to correlate with ages of >4 Ma, ca 2 Ma and <0.5 Ma, which may be further subdivided based on preservation of outcrop. Geochemical compositions of the dominantly basaltic products become increasingly alkaline and enriched in incompatible elements from Phases 1 to 2, with Phase 3 eruptions both covering the entire geochemical range and extending into increasingly enriched compositions. This research highlights the importance of a multifaceted approach to landform mapping and demonstrates that additional volcanic centres may yet be discovered in the Newer Volcanics Province