Preliminary Study and Proposal for Restoring a Jesuit College at Saragossa, Spain

A historical study and a construction pathology survey were conducted prior to proposing a solution for restoring the upper windows on the south side of Old San Carlos College at Saragossa (16th-17th centuries), wich had been forteited to add a third storey to the cloister. Althought initially designed to a simple large hall format, the church is a harmonius blend of Aragonese Gothic architecture and typical Jesuit scheme, consisting in a central nave flanket by chapel-confessional and raised galleries for the community. A subsequent enlargement of the roof, wich rests on the original framing over the central nave, reduced the mechanical strength of the principal rafters on the opposite side, prompting a concomitant imbalance of forces that has affected the entire structure. In view of the foregoing, in addition to restituting the upper window, the proposal solution envisages restoring the roof over the central nave to its original design, and with the interior lighting in the church.

Polymer-solvent interaction parameters of SBS rubbers by inverse gas chromatography measurements

The solubility parameters of two SBS commercial rubbers with different structures (lineal and radial), and with slightly different styrene content have been determined by inverse gas chromatography technique. The Flory–Huggins interaction parameters of several polymer–solvent mixtures have also been calculated. The influence of the polymer composition, the solvent molecular weight and the temperature over these parameters have been discussed; besides, these parameters have been compared with previous ones, obtained by intrinsic viscosity measurements. From the Flory–Huggins interaction parameters, the infinite dilution activity coefficients of the solvents have been calculated and fitted to the well-known NRTL model. These NRTL binary interaction parameters have a great importance in modelling the separation steps in the process of obtaining the rubber.

Intraply fracture of fiber-reinforced composites: microscopic mechanisms and modeling

The fracture behavior parallel to the fibers of an E-glass/epoxy unidirectional laminate was studied by means of three-point tests on notched beams. Selected tests were carried out within a scanning electron microscope to ascertain the damage and fracture micromechanisms upon loading. The mechanical behavior of the notched beam was simulated within the framework of the embedded cell model, in which the actual composite microstructure was resolved in front of the notch tip. In addition, matrix and interface properties were independently measured in situ using a nanoindentor. The numerical simulations very accurately predicted the macroscopic response of the composite as well as the damage development and crack growth in front of the notch tip, demonstrating the ability of the embedded cell approach to simulate the fracture behavior of heterogeneous materials. Finally, this methodology was exploited to ascertain the influence of matrix and interface properties on the intraply toughness.

Implications of macromolecular crowding for signal transduction and metabolite channeling

The effect of different total enzyme concentrations on the flux through the bacterial phosphoenolpyruvate:carbohydrate phosphotransferase system (PTS) in vitro was determined by measuring PTS-mediated carbohydrate phosphorylation at different dilutions of cell-free extract of Escherichia coli. The dependence of the flux on the protein concentration was more than linear but less than quadratic. The combined flux–response coefficient of the four enzymes constituting the glucose PTS decreased slightly from values of ≈1.8 with increasing protein concentrations in the assay. Addition of the macromolecular crowding agents polyethylene glycol (PEG) 6000 and PEG 35000 led to a sharper decrease in the combined flux–response coefficient, in one case to values of ≈1. PEG 6000 stimulated the PTS flux at lower protein concentrations and inhibited the flux at higher protein concentrations, with the transition depending on the PEG 6000 concentration. This suggests that macromolecular crowding decreases the dissociation rate constants of enzyme complexes. High concentrations of the microsolute glycerol did not affect the combined flux–response coefficient. The data could be explained with a kinetic model of macromolecular crowding in a two-enzyme group-transfer pathway. Our results suggest that, because of the crowded environment in the cell, the different PTS enzymes form complexes that live long on the time-scale of their turnover. The implications for the metabolic behavior and control properties of the PTS, and for the effect of macromolecular crowding on nonequilibrium processes, are discussed.

Obtenção e caracterização de PLA reforçado com nanocelulose.

A celulose é o polímero natural renovável disponível em maior abundância atualmente. Por possuir estrutura semicristalina, é possível extrair seus domínios cristalinos através de procedimentos que ataquem sua fase amorfa, como a hidrólise ácida, obtendo-se assim partículas cristalinas chamadas nanopartículas de celulose (NCs). Estas nanopartículas têm atraído enorme interesse científico, uma vez que possuem propriedades mecânicas, como módulo de elasticidade e resistência à tração, semelhantes a várias cargas inorgânicas utilizadas na fabricação de compósitos. Além disso, possuem dimensões nanométricas, o que contribui para menor adição de carga à matriz polimérica, já que possuem maior área de superfície, quando comparadas às cargas micrométricas. Nanocompósitos formados pela adição destas cargas em matrizes poliméricas podem apresentar propriedades comerciais atraentes, como barreira a gases, melhores propriedades térmicas e baixa densidade, quando comparados aos compósitos tradicionais. Como se trata de uma carga com dimensões nanométricas, obtida de fontes renováveis, uma das principais áreas de interesse para aplicação deste reforço é em biopolímeros biodegradáveis. O poli(ácido lático) (PLA), é um exemplo de biopolímero com propriedades mecânicas, térmicas e de processamento superiores a de outros biopolímeros comerciais. No presente trabalho foram obtidas nanopartículas de celulose (NCs), por meio de hidrólise ácida, utilizando-se três métodos distintos, com o objetivo de estudar o método mais eficiente para a obtenção de NCs adequadas à aplicação em compósitos de PLA. Os Métodos I e II empregam extração das NCs por meio do H2SO4, diferenciando-se apenas pela neutralização, a qual envolve diálise ou neutralização com NaHCO3, respectivamente. No Método III a extração das NCs foi realizada com H3PO4. As NCs foram caracterizadas por diferentes técnicas, como difração de raios X (DRX), análise termogravimétrica (TG), espectroscopia vibracional de absorção no infravermelho (FTIR), microscopia eletrônica de transmissão (MET) e microscopia de força atômica (MFA). Os resultados de caracterização das NCs indicaram que, a partir de todos os métodos utilizados, há formação de nanocristais de celulose (NCCs), entretanto, apenas os NCCs obtidos pelos Métodos II e III apresentaram estabilidade térmica suficiente para serem empregados em compósitos preparados por adição da carga no polímero em estado fundido. A incorporação das NCs em matriz de PLA foi realizada em câmara de mistura, com posterior moldagem por prensagem a quente. Compósitos obtidos por adição de NCs obtidas pelo Método II foram caracterizados por calorimetria exploratória diferencial (DSC), análise termogravimétrica, microscopia óptica, análises reológicas e microscopia eletrônica de varredura (MEV). A adição de NCs, extraídas pelo Método II, em matriz de PLA afetou o processo de cristalização do polímero, o qual apresentou maior grau de cristalinidade. Além disso, a adição de 3% em massa de NCs no PLA foi suficiente para alterar seu comportamento reológico. Os resultados reológicos indicaram que a morfologia do compósito é, predominantemente, composta por uma dispersão homogênea e fina da carga na fase matriz. Micrografias obtidas por MEV corroboram os resultados reológicos, mostrando, predominantemente a presença de partículas de NC em escala nanométrica. Compósitos de PLA com NCs obtidas pelo Método III apresentaram aglomerados de partículas de NC em escala micro e milimétrica, ao longo da fase matriz, e não foram extensivamente caracterizados.

Reverse Vending Machines: A Potential Solution for the Florida Plastic Waste Management Challenge

The waste of plastic beverage bottles creates environmental problems and takes up a large volume of landfill space. The high rate of consumption of plastics in the State of Florida is challenging the disposal capacity of waste authorities. The lack of the reverse vending machines in the State of Florida, including applicable scientific or technical literature represented an opportunity for this research to discuss the applicability of this equipment as a potential solution for the management of the plastic waste in Florida. With this research document, I will propose a recycling system for plastic bottles made with PET based on the implementation of reverse vending machines, stressing the importance of the creation of policies that promote recycling and public participation.

Synthesis, Characterization and Conducting Properties of Nanocomposites of Intercalated 2-Aminophenol with Aniline in Sodium-Montmorillonite

A simple method was used to synthesize poly(2-aminophenol), poly(2-aminophenol-co-Aniline) and polyaniline nanocomposites with sodium-montmorillonite (Na-M) using in situ intercalative oxidative polymerization. Morphology and thermal properties of the synthesized nanocomposites were examined by transmission electron microscopy (TEM) and thermogravimetric analysis. The thermal analysis shows an improved thermal stability of the nanocomposites in comparison with the pure poly(2-aminophenol). The intercalation of polymers into the clay layers was confirmed by X-ray diffraction studies, TEM images and FTIR spectroscopy. In addition, the room temperature conductivity values of these nanocomposites varied between 8.21 × 10−5 and 6.76 × 10−4 S cm−1. The electrochemical behavior of the polymers extracted from the nanocomposites, has been analyzed by cyclic voltammetry. Good electrochemical response has been observed for polymer films; the observed redox processes indicate that the polymerization into Na-M produces electroactive polymers.

Ethanol dehydration via azeotropic distillation with gasoline fraction mixtures as entrainers: A pilot-scale study with industrially produced bioethanol and naphta

Various hydrocarbons (n-hexane, cyclohexane, toluene, isooctane) and mixtures of them (binary, ternary or quaternary), as well as two different types of industrially produced naphtha (one obtained by direct distillation and the other from a catalytic cracking process), have been tested as candidate entrainers to dehydrate ethanol. The tests were carried out in an azeotropic distillation column on a semi pilot plant. The results show that it is possible to dehydrate bioethanol using naphtha as entrainer, obtaining as a result a fuel blend with negligible water content and ready for immediate use in motor vehicles.

Chemistry and boron isotope ratios of Izu arc front volcanic rocks

The process of fluid release from the subducting slab beneath the Izu arc volcanic front (Izu VF) was examined by measuring B concentrations and B isotope ratios in the Neogene fallout tephra (ODP Site 782A). Both were measured by secondary ion mass spectrometry, in a subset of matrix glasses and glassy plagioclase-hosted melt inclusions selected from material previously analyzed for major and trace elements (glasses) and radiogenic isotopes (Sr, Nd, Pb; bulk tephra). These tephra glasses have high B abundances (~10-60 ppm) and heavy delta11B values (+4.5? to +12.0?), extending the previously reported range for Izu VF rocks (delta11B, +7.0? to +7.3?). The glasses show striking negative correlations of delta11B with large ion lithophile element (LILE)/Nb ratios. These correlations cannot be explained by mixing two separate slab fluids, originating from the subducting sediment and the subducting basaltic crust, respectively (model A). Two alternative models (models B and C) are proposed. Model B proposes that the inverse correlations are inherited from altered oceanic crust (AOC), which shows a systematic decrease of B and LILE with increasing depth (from basaltic layer 2A to layer 3), paralleled by an increase in delta11B (from ~ +1? to +10? to +24?). In this model, the contribution of sedimentary B is insignificant (<4% of B in the Izu VF rocks). Model C explains the correlation as a mixture of a low-delta11B (~ +1?) 'composite' slab fluid (a mixture of metasediment- and metabasalt-derived fluids) with a metasomatized mantle wedge containing elevated B (~1-2 ppm) and heavy delta11B (~ +14?). The mantle wedge was likely metasomatized by 11B-rich fluids beneath the outer forearc, and subsequently down dragged to arc front depths by the descending slab. Pb-B isotope systematics indicate that, at arc front depths, ~ 53% of the B in the Izu VF is derived from the wedge. This implies that the heavy delta11B values of Izu VF rocks are largely a result of fluid fractionation, and do not reflect variations in slab source provenance (i.e. subducting sediment vs. basaltic crust). Since the B content of the peridotite at the outer forearc (7-58 ppm B, mean 24 +/- 16 ppm) is much higher than beneath the arc front (~1-2 ppm B), the hydrated mantle wedge must have released a B-rich fluid on its downward path. This 'wedge flux' can explain (1) the across-arc decrease in B and delta11B (e.g. Izu, Kuriles), without requiring a progressive decrease in fluid flux from the subducting slab, and (2) the thermal structure of volcanic arcs, as reflected in the B and delta11B variations of volcanic arc rocks.

Polymerizable Peptide Monomers for the Targeted and Intracellular Delivery of Cancer Therapeutics

Thesis (Ph.D.)--University of Washington, 2016-06

Electrodeposition of composite copper/liquid-containing microcapsule coatings

This paper presents results on the preparation of microcapsules containing liquid organosilica, and their co-deposition with copper in an acidic copper electrolyte onto a carbon steel cathode to form a copper/microcapsule composite coating. Microscopic analyses of the surface and the cross-section of the coating confirm the incorporation of the liquid-containing microcapsules in the coating layer. The influence of microcapsules in the electrolyte on the cathode polarization, as well as that of process conditions on the microcapsule inclusion, is also discussed. (C) 2004 Kluwer Academic Publishers.

Infrared microspectroscopic mapping of the homogeneity of extruded blends: Application to starch/polyester blends

Blends of starch and a biodegradable polyester, produced by an extrusion process, which included a cross-linker/compatibilizer (maleic anhydride) and an initiator (dicumyl peroxide), were studied by infrared (IR) microspectroscopy using an attenuated total reflectance (ATR) objective. Extruded material, which had a diameter of about 3 mm, was sectioned and embedded in epoxy resin prior to IR analysis. Spectra were collected in a grid pattern across the sectioned face of the sample. Measurement of various band parameters from the spectra allowed IR maps to be constructed containing semi-quantitative information about the distribution of blend components. These maps showed the quality of the blend on a microscopic scale and showed how it varied with different concentrations of compatibilizer and initiator. (c) 2005 Elsevier Ltd. All rights reserved.

Mechanics of cellular adhesion to artificial artery templates

We are using polymer templates to grow artificial artery grafts in vivo for the replacement of diseased blood vessels. We have previously shown that adhesion of macrophages to the template starts the graft formation. We present a study of the mechanics of macrophage adhesion to these templates on a single cell and single bond level with optical tweezers. For whole cells, in vitro cell adhesion densities decreased significantly from polymer templates polyethylene to silicone to Tygon (167, 135, and 65 cells/mm(2)). These cell densities were correlated with the graft formation success rate (50%, 25%, and 0%). Single-bond rupture forces at a loading rate of 450 pN/s were quantified by adhesion of trapped 2-mm spheres to macrophages. Rupture force distributions were dominated by nonspecific adhesion (forces, < 40 pN). On polystyrene, preadsorption of fibronectin or presence of serum proteins in the cell medium significantly enhanced adhesion strength from a mean rupture force of 20 pN to 28 pN or 33 pN, respectively. The enhancement of adhesion by fibronectin and serum is additive (mean rupture force of 43 pN). The fraction of specific binding forces in the presence of serum was similar for polystyrene and polymethyl-methacrylate, but specific binding forces were not observed for silica. Again, we found correlation to in vivo experiments, where the density of adherent cells is higher on polystyrene than on silica templates, and can be further enhanced by fibronectin adsorption. These findings show that in vitro adhesion testing can be used for template optimization and to substitute for in-vivo experiments.

The use of microviscometry to study polymer dissolution from solid dispersion drug delivery systems

Solid dispersions can be used to improve dissolution of poorly soluble drugs and PVP is a common polymeric carrier in such systems. The mechanisms controlling release of drug from solid dispersions are not fully understood and proposed theories are dependent on an understanding of the dissolution behaviour of both components of the dispersion. This study uses microviscometry to measure small changes in the viscosity of the dissolution medium as the polymer dissolves from ibuprofen-PVP solid dispersions. The microviscometer determines the dynamic and kinematic viscosity of liquids based on the rolling/falling ball principle. Using a standard USP dissolution apparatus, the dissolution of the polymer from the solid dispersion was easily measured alongside drug release. Drug release was found to closely follow polymer dissolution at the molecular weights and ratios used. The combination of sensitivity and ease of use make microviscometry a valuable technique for the elucidation of mechanisms governing drug release from polymeric delivery systems. © 2004 Elsevier B.V. All rights reserved.