Robottisolun servotekniikan kehittäminen

Työn kehityksen kohteena toimii CIRB 500i –robottisolu, jonka sisällä työskentelee korkeaan tuotantokapasiteettiin kehitetty näköjärjestelmällä ohjattu sähköservomanipulaattori. Kokonaisuutena ajatellen työ tekee servotekniikan osalta poikkileikkauksen CIRB 500i –robottisolun matkasta prototyypistä tuotteeksi erilaisine kehitysvaiheineen. Työn alkutaipaleella perehdytään pitkälle pelkkään teoriaan nojautuen mitä on servotekniikka, miten se toimii ja kuinka se viritetään. Tämän jälkeen edellä opitut teoriat konkretisoidaan CIRB 500i –robottisoluun ja siinä käytettävään servotekniikkaan. Robottisolun komponenttien ja laitteistojen tullessa tutuiksi mietitään ja kehitetään kuinka robottisolusta saataisiin entistä kehittyneempi ja käytännöllisempi teknillisestä näkökulmasta katsoen kuitenkaan valmistamisen kustannustehokkuutta unohtamatta. Loppupuolella analysoidaan miten edellä tehdyt kehitystoimenpiteet ovat vaikuttaneet robottisolun toimintaan ja valmistamiseen. Lopuksi sovelletaan teoriaosuuden virityskeinoja servojen virittämiseen käytännössä ja analysoidaan saavutettuja kehittämistyön tuloksia. Lisäksi tehdään katsaus CIRB 500i –robottisolun tulevaisuuden näkymiin.

Fatigue analysis of brackets with and without scallop for bridge and other deck structure using effective notch stress.

Due to functional requirement of a structural detail brackets with and without scallop are frequently used in bridges, decks, ships and offshore structure. Scallops are designed to serve as passage way for fluids, to reduce weld length and plate distortions. Moreover, scallops are used to avoid intersection of two or more welds for the fact that there is the presence of inventible inherent initial crack except for full penetrated weld and the formation of multi-axial stress state at the weld intersection. Welding all around the scallop corner increase the possibility of brittle fracture even for the case the bracket is not loaded by primary load. Avoiding of scallop will establish an initial crack in the corner if bracket is welded by fillet welds. If the two weld run pass had crossed, this would have given a 3D residual stress situation. Therefore the presences and absence of scallop necessitates the 3D FEA fatigue resistance of both types of brackets using effective notch stress approach ( ). FEMAP 10.1 with NX NASTRAN was used for the 3D FEA. The first and main objective of this research was to investigate and compare the fatigue resistance of brackets with and without scallop. The secondary goal was the fatigue design of scallops in case they cannot be avoided for some reason. The fatigue resistance for both types of brackets was determined based on approach using 1 mm fictitiously rounded radius based on IIW recommendation. Identical geometrical, boundary and loading conditions were used for the determination and comparison of fatigue resistance of both types of brackets using linear 3D FEA. Moreover the size effect of bracket length was also studied using 2D SHELL element FEA. In the case of brackets with scallop the flange plate weld toe at the corner of the scallop was found to exhibit the highest and made the flange plate weld toe critical for fatigue failure. Whereas weld root and weld toe at the weld intersections were the highly stressed location for brackets without scallop. Thus weld toe for brackets with scallop, and weld root and weld toe for brackets without scallop were found to be the critical area for fatigue failure. Employing identical parameters on both types of brackets, brackets without scallop had the highest except for full penetrated weld. Furthermore the fatigue resistance of brackets without scallop was highly affected by the lack of weld penetration length and it was found out that decreased as the weld penetration was increased. Despite the fact that the very presence of scallop reduces the stiffness and also same time induce stress concentration, based on the 3D FEA it is worth concluding that using scallop provided better fatigue resistance when both types of brackets were fillet welded. However brackets without scallop had the highest fatigue resistance when full penetration weld was used. This thesis also showed that weld toe for brackets with scallop was the only highly stressed area unlike brackets without scallop in which both weld toe and weld root were the critical locations for fatigue failure when different types of boundary conditions were used. Weld throat thickness, plate thickness, scallop radius, lack of weld penetration length, boundary condition and weld quality affected the fatigue resistance of both types of brackets. And as a result, bracket design procedure, especially welding quality and post weld treatment techniques significantly affect the fatigue resistance of both type of brackets.

Singular Reference Without Singular Thought

Abstract In this paper I challenge the widespread assumption that the conditions for singular reference are more or less the same as the conditions for singular thought. I claim that we refer singularly to things without thinking singularly about them more often than it is usually believed. I first argue that we should take the idea that singular thought is non-descriptive thought very seriously. If we do that, it seems that we cannot be so liberal about what counts as acquaintance; only perception (and memory) will do. I also briefly discuss and reject semantic instrumentalism. Finally, I argue that while singular reference is cheap, singular thought comes only at a price.

Making Sense of Shared Leadership. A case study of leadership processes and practices without formal leadership structure in the team context

Leadership is essential for the effectiveness of the teams and organizations they are part of. The challenges facing organizations today require an exhaustive review of the strategic role of leadership. In this context, it is necessary to explore new types of leadership capable of providing an effective response to new needs. The presentday situations, characterized by complexity and ambiguity, make it difficult for an external leader to perform all leadership functions successfully. Likewise, knowledge-based work requires providing professional groups with sufficient autonomy to perform leadership functions. This study focuses on shared leadership in the team context. Shared leadership is seen as an emergent team property resulting from the distribution of leadership influence across multiple team members. Shared leadership entails sharing power and influence broadly among the team members rather than centralizing it in the hands of a single individual who acts in the clear role of a leader. By identifying the team itself as a key source of influence, this study points to the relational nature of leadership as a social construct where leadership is seen as social process of relating processes that are co-constructed by several team members. Based on recent theoretical developments concerned with relational, practice-based and constructionist approaches to the study of leadership processes, this thesis proposes the study of leadership interactions, working processes and practices to focus on the construction of direction, alignment and commitment. During the research process, critical events, activities, working processes and practices of a case team have been examined and analyzed with the grounded theory –approach in the terms of shared leadership. There are a variety of components to this complex process and a multitude of factors that may influence the development of shared leadership. The study suggests that the development process of shared leadership is a common sense -making process and consists of four overlapping dimensions (individual, social, structural, and developmental) to work with as a team. For shared leadership to emerge, the members of the team must offer leadership services, and the team as a whole must be willing to rely on leadership by multiple team members. For these individual and collective behaviors to occur, the team members must believe that offering influence to and accepting it from fellow team members are welcome and constructive actions. Leadership emerges when people with differing world views use dialogue and collaborative learning to create spaces where a shared common purpose can be achieved while a diversity of perspectives is preserved and valued. This study also suggests that this process can be supported by different kinds of meaning-making and process tools. Leadership, then, does not reside in a person or in a role, but in the social system. The built framework integrates the different dimensions of shared leadership and describes their relationships. This way, the findings of this study can be seen as a contribution to the understanding of what constitutes essential aspects of shared leadership in the team context that can be of theoretical value in terms of advancing the adoption and development process of shared leadership. In the real world, teams and organizations can create conditions to foster and facilitate the process. We should encourage leaders and team members to approach leadership as a collective effort that the team can be prepared for, so that the response is rapid and efficient.

Control system for forced-air cooling of horticultural products

This work is a study of the implementation of a classical controller using a tuning method referred to as IMC (Internal Model Control) and aimed at the reduction of electrical energy consumption by the appropriate relation between energy consumption and the cooling time with forced air. The supervisory system installed was able to manipulate the variable of frequency of the signal power of the exhaust fan engine (forced air module), to accelerate or decelerate the loss of heat from the product to be cooled by airflow variation that passes through the mass of the produce. The results demonstrated a reduction in energy consumption from 64% and an increase of only 8% in the cooling time to the system using PI/IMC (Proportional - Integral with IMC) tuning method compared with the system in its operating nominal condition. This PI/IMC control may be implemented directly in a frequency converter, without the need to purchase a computer or PLC (programmable logic controller) to run the dedicated application, increasing its economical viability.

Comparison of maps of spatial variability of soil resistance to penetration constructed with and without covariables using a spatial linear model

A study about the spatial variability of data of soil resistance to penetration (RSP) was conducted at layers 0.0-0.1 m, 0.1-0.2 m and 0.2-0.3 m depth, using the statistical methods in univariate forms, i.e., using traditional geostatistics, forming thematic maps by ordinary kriging for each layer of the study. It was analyzed the RSP in layer 0.2-0.3 m depth through a spatial linear model (SLM), which considered the layers 0.0-0.1 m and 0.1-0.2 m in depth as covariable, obtaining an estimation model and a thematic map by universal kriging. The thematic maps of the RSP at layer 0.2-0.3 m depth, constructed by both methods, were compared using measures of accuracy obtained from the construction of the matrix of errors and confusion matrix. There are similarities between the thematic maps. All maps showed that the RSP is higher in the north region.

Managing without growth : slower by design, not disaster

Kirjallisuusarvostelu

Väriavaruuden rakenteen muokkaaminen yhtenäisyyden parantamiseksi

Pienien värierojen mittaamiseen käytetään CIE:n (The International Commission on Illumination) kehittämää ja standardoitua CIELAB – väriavaruutta ja sille suunniteltua CIEDE2000 – värieromittaria. CIELAB ei kuitenkaan ole täysin yhtenäinen ja siksi mittareita joudutaan virittämään sopivammiksi tähän väriavaruuteen. Työssä tutkitaan millä tavoin CIELAB - väriavaruutta voitaisiin korjata, jotta siitä saataisiin yhtenäisempi ja yksinkertainen ja virittämättömämpi värieromittari toimisi siinä paremmin. Työn tuloksena saatu muokattu väriavaruus paransi yhtenäisyyttä keskimäärin kymmenen prosenttia, mikä on liian vähän kun tavoitteena oli 30 - 50 prosenttia.

Single access laparoscopic cholecystectomy: technique without the need for special materials and with better ergonomics

The authors describe a surgical technique which allows, without increasing costs, to perform laparoscopic cholecystectomy with a single incision, without using specific materials and with better surgical ergonomics. The technique consists of a longitudinal umbilical incision, navel detachment, use of a permanent 10mm trocar and two clamps directly and bilaterally through the aponeurosis without the use of 5mm trocars, transcutaneous gallbladder repair with straight needle cotton suture, ligation with unabsorbable suture and umbilical incision for the specimen extraction. The presented technique enables the procedure with conventional and permanent materials, improving surgical ergonomics, with safety and aesthetic advantages.

Fifty consecutive pancreatectomies without mortality

Objective: to report the group's experience with a series of patients undergoing pancreatic resection presenting null mortality rates. Methods: we prospectively studied 50 consecutive patients undergoing pancreatic resections for peri-ampullary or pancreatic diseases. Main local complications were defined according to international criteria. In-hospital mortality was defined as death occurring in the first 90 postoperative days. Results: patients' age ranged between 16 and 90 years (average: 53.3). We found anemia (Hb < 12g/dl) and preoperative jaundice in 38% and 40% of cases, respectively. Most patients presented with peri-ampullary tumors (66%). The most common surgical procedure was the Kausch - Whipple operation (70%). Six patients (12%) needed to undergo resection of a segment of the mesenteric-portal axis. The mean operative time was 445.1 minutes. Twenty two patients (44%) showed no clinical complications and presented mean hospital stay of 10.3 days. The most frequent complications were pancreatic fistula (56%), delayed gastric emptying (17.1%) and bleeding (16%). Conclusion : within the last three decades, pancreatic resection is still considered a challenge, especially outside large specialized centers. Nevertheless, even in our country (Brazil), teams seasoned in such procedure can reach low mortality rates.

AMB system for high-speed motors using automatic commissioning

The general trend towards increasing e ciency and energy density drives the industry to high-speed technologies. Active Magnetic Bearings (AMBs) are one of the technologies that allow contactless support of a rotating body. Theoretically, there are no limitations on the rotational speed. The absence of friction, low maintenance cost, micrometer precision, and programmable sti ness have made AMBs a viable choice for highdemanding applications. Along with the advances in power electronics, such as signi cantly improved reliability and cost, AMB systems have gained a wide adoption in the industry. The AMB system is a complex, open-loop unstable system with multiple inputs and outputs. For normal operation, such a system requires a feedback control. To meet the high demands for performance and robustness, model-based control techniques should be applied. These techniques require an accurate plant model description and uncertainty estimations. The advanced control methods require more e ort at the commissioning stage. In this work, a methodology is developed for an automatic commissioning of a subcritical, rigid gas blower machine. The commissioning process includes open-loop tuning of separate parts such as sensors and actuators. The next step is to apply a system identi cation procedure to obtain a model for the controller synthesis. Finally, a robust model-based controller is synthesized and experimentally evaluated in the full operating range of the system. The commissioning procedure is developed by applying only the system components available and a priori knowledge without any additional hardware. Thus, the work provides an intelligent system with a self-diagnostics feature and an automatic commissioning.

Is it worth while driving without a trailer?

kuv., 22 x 31 cm

Tunable lumped-element bandpass filters for Cognitive Radio application

In this thesis the design of bandpass filters tunable at 400 MHz – 800 MHz was under research. Microwave filters are vital components which provide frequency selectivity in wide variety of electronic systems operating at high frequencies. Due to the occurrence of multi-frequency bands communication and diverse applications of wireless devices, requirement of tunable filters exists. The one of potential implementation of frequency-agile filters is frontends and spectrum sensors in Cognitive Radio (CR). The principle of CR is to detect and operate at a particular available spectrum without interfering with the primary user’s signals. This new method allows improving the efficiency of utilizing allocated spectrum such as TV band (400 MHz – 800 MHz). The focus of this work is development of sufficiently compact, low cost tunable filters with quite narrow bandwidth using currently available lumped-element components and PCB board technology. Filter design, different topologies and methods of tuning of bandpass filters are considered in this work. As a result, three types of topologies of bandpass filter were simulated and realised. They use digitally tunable capacitors (DTCs) for adjusting central frequency at TV "white space" spectrum. Measurements revealed that schematics presented in this work have proper output response and filters are successfully tuned by DTCs.