Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.

Semantics-supported cooperative learning for enhanced awareness

Awareness is required for supporting all forms of cooperation. In Computer Supported Collaborative Learning (CSCL), awareness can be used for enhancing collaborative opportunities across physical distances and in computer-mediated environments. Shared Knowledge Awareness (SKA) intends to increase the perception about the shared knowledge, students have in a collaborative learning scenario and also concerns the understanding that this group has about it. However, it is very difficult to produce accurate awareness indicators based on informal message exchange among the participants. Therefore, we propose a semantic system for cooperation that makes use of formal methods for knowledge representation based on semantic web technologies. From these semantics-enhanced repository and messages, it could be easier to compute more accurate awareness.

Evaluation of the Development of Metacognitive Knowledge Supported by the KnowCat System

The aim of this study was to examine the development of the metacognitive knowledge of a group of higher education students who participated actively in an experiment based on a Computer Supported Collaborative Learning environment called KnowCat. Eighteen university students participated in a 12-month learning project during which the KnowCat learning environment was used to support scaffolding process among equals during problem-solving tasks. After using KnowCat, the students were interviewed over their work in this shared workspace. Qualitative analysis revealed that the educational application of KnowCat can favour and improve the development of metacognitive knowledge.

Wiki-supported collaborative learning in primary education. How a dialogic space is created for thinking together

This paper explores how wikis may be used to support primary education students’ collaborative interaction and how such an interaction process can be characterised. The overall aim of this study is to analyse the collaborative processes of students working together in a wiki environment, in order to see how primary students can actively create a shared context for learning in the wiki. Educational literature has already reported that wikis may support collaborative knowledge-construction processes, but in our study we claim that a dialogic perspective is needed to accomplish this. Students must develop an intersubjective orientation towards each others’ perspectives, to co-construct knowledge about a topic. For this purpose, our project utilised a ‘Thinking Together’ approach to help students develop an intersubjective orientation towards one another and to support the creation of a ‘dialogic space’ to co-construct new understanding in a wiki science project. The students’ asynchronous interaction process in a primary classroom -- which led to the creation of a science text in the wiki -- was analysed and characterised, using a dialogic approach to the study of CSCL practices. Our results illustrate how the Thinking Together approach became embedded within the wiki environment and in the students’ collaborative processes. We argue that a dialogic approach for examining interaction can be used to help design more effective pedagogic approaches related to the use of wikis in education and to equip learners with the competences they need to participate in the global knowledge-construction era.

Sisäisten donorien vaikutus Polypropeeni Ziegler-Natta katalyytissä

Tässä työssä tutkittiin erilaisten sisäisten donorien vaikutusta polypropeenin ominaisuuksiin käytettäessä Ziegler-Natta-katalyyttiä, joka valmistettiin Borealiksen aiemmin kehittämällä kaksifaasimenetelmällä. Tällä uudella menetelmällä katalyytti voidaan valmistaa ilman lisättyä sisäistä donoria ja kantajaa. Katalyyttihiukkaset saadaan kaksifaasisysteemin ansiosta muodoltaan pyöreiksi. Työn kokeellisessa osassa valmistettiin erilaisia Mg-komplekseja, jossa sisäinen donori muodostuu in-situ alkoholin ja karboksyylihappokloridin reagoidessa keskenään. Katalyyttisynteesissä Mg-kompleksi reagoi TiCl4:n kanssa. Saatujen katalyyttien ominaisuuksia testattiin polymeroimalla niillä propeenia 70 °C:ssa tunnin ajan. Polymeerien ominaisuuksia tutkittiin useiden eri karakterisointimenetelmien avulla. Lisäksi tutkittiin mahdollisuutta valmistaa katalyytti, joka ei sisältäisi ftalaattia. Työssä havaittiin, että katalyytin valmistusmenetelmä on käyttökelpoinen myös muilla sisäisillä donoreilla kuin referenssinä käytetyllä DOP:lla. Kaksiliuosfaasi-systeemi saatiin aikaan myös kahdella muulla työssä tutkitulla sisäisellä donorilla. Lisäksi faasitasapainokokeissa kahden liuosfaasin systeemi saatiin aikaan sisäisellä donorilla, joka ei sisältänyt ftalaattia. Kyseisellä katalyytillä havaittiin olevan muista katalyyteistä poikkeavia ominaisuuksia. Esimerkiksi se antoi matalamman isotaktisuuden kuin referenssikatalyytti ja se saattaisikin soveltua matalan isotaktisuuden pehmeille tuotteille. Työssä kokeiltiin yhdellä uudella katalyytillä myös eteenin polymerointia, sillä katalyytin donoripitoisuus oli hyvin matala. Katalyytin aktiivisuus eteenipolymeroinnissa oli varsin hyvä.

Simulation Supported Robot Programming using XML

The main objective of this master's thesis is to study robot programming using simulation software, and also how to embed the simulation software into company's own robot controlling software. The further goal is to study a new communication interface to the assembly line's components -more precisely how to connect the robot cell into this new communication system. Conveyor lines are already available where the conveyors use the new communication standard. The robot cell is not yet capable of communicating with to other devices using the new communication protocols. The main problem among robot manufacturers is that they all have their own communication systems and programming languages. There has not been any common programming language to program all the different robot manufacturers robots, until the RRS (Realistic Robot Simulation) standards were developed. The RRS - II makes it possible to create the robot programs in the simulation software and it gives a common user interface for different robot manufacturers robots. This thesis will present the RRS - II standard and the robot manufacturers situation for the RRS - II support. Thesis presents how the simulation software can be embedded into company's own robot controlling software and also how the robot cell can be connected to the CAMX (Computer Aided Manufacturing using XML) communication system.

From caging to rouse dynamics in polymer melts with intramolecular barriers: a critical test of the mode coupling theory

By means of computer simulations and solution of the equations of the mode coupling theory (MCT),we investigate the role of the intramolecular barriers on several dynamic aspects of nonentangled polymers. The investigated dynamic range extends from the caging regime characteristic of glass-formers to the relaxation of the chain Rouse modes. We review our recent work on this question,provide new results, and critically discuss the limitations of the theory. Solutions of the MCT for the structural relaxation reproduce qualitative trends of simulations for weak and moderate barriers. However, a progressive discrepancy is revealed as the limit of stiff chains is approached. This dis-agreement does not seem related with dynamic heterogeneities, which indeed are not enhanced by increasing barrier strength. It is not connected either with the breakdown of the convolution approximation for three-point static correlations, which retains its validity for stiff chains. These findings suggest the need of an improvement of the MCT equations for polymer melts. Concerning the relaxation of the chain degrees of freedom, MCT provides a microscopic basis for time scales from chain reorientation down to the caging regime. It rationalizes, from first principles, the observed deviations from the Rouse model on increasing the barrier strength. These include anomalous scaling of relaxation times, long-time plateaux, and nonmonotonous wavelength dependence of the mode correlators.

Service product structure supported by remote diagnostics

Työn tavoitteena oli määrittää etähuoltokonseptin yleinen rakenne sekä selvittää asiakkaille tarjottavia modulaarisia palvelutuotteita. Aluksi selvitettiin huoltokonseptin rakennetta kirjallisuuden ja asiantuntijoiden haastattelujen avulla. Asiantuntijoiden haastattelut toteutettiin vapaamuotoisesti kysymyslistaa apuna käyttäen. Tämän lisäksi työssä pohditaan KM, CRM ja PDM rooleja etähuoltokonseptin kannalta sekä tutkaillaan etähuollon tulevaisuuden näkymiä.Diplomityössä käsitellään modulaarisuutta yleisellä tasolla. Moduularisuus on moniulotteinen termi. Usein sillä tarkoitetaan yrityksen sisäistä tuotekehityksen hallintaa. Toisaalta se voidaan nähdä myös asiakkaalle tarjottavina tuotteina ja tässä diplomityössä on keskitytty tähän puoleen. Loppuosa diplomityöstä käsittelee palvelutuotteiden tuotteistamisprosessia.Diplomityön tuloksena hahmoteltiin etähuolto konseptia ja tutkittiin mahdollisia palvelutuotteita, joita voidaan sisällyttää etähuoltokonseptiin. Tämän lisäksi toteutettiin osa tuotteistamisprosessista. Etähuollon kehittäminen on haasteellista. Haasteeksi jää tuotekehitystoiminnan ja palvelupuolen toiminnan tehostaminen, jotta tuotteita voitaisiin jo suunnittelupuolella kehittää etähuollon tarpeisiin. Kehittäminen vaatii molempien puolien aktiivista osallistumista.

Dynamic arrest in polymer melts: competition between packing and intramolecular barriers

We present molecular dynamics simulations of a simple model for polymer melts with intramolecular barriers. We investigate structural relaxation as a function of the barrier strength. Dynamic correlators can be consistently analyzed within the framework of the mode coupling theory of the glass transition. Control parameters are tuned in order to induce a competition between general packing effects and polymer-specific intramolecular barriers as mechanisms for dynamic arrest. This competition yields unusually large values of the so-called mode coupling theory exponent parameter and rationalizes qualitatively different observations for simple bead-spring and realistic polymers. The systematic study of the effect of intramolecular barriers presented here also establishes a fundamental difference between the nature of the glass transition in polymers and in simple glass formers.

Unbreakable PT symmetry of solitons supported by inhomogeneous defocusing nonlinearity

Peer Reviewed

Hidróxidos duplos lamelares: síntese, estrutura, propriedades e aplicações

The layered double hydroxides, known as anionic clays and represented by the general formula [M2+1-x M3+x (OH) 2]x+ Am-x/m·nH 2O, are a group of materials which are of much interest currently. They present a variety of potential applications as adsorbents, catalysts and catalyst support, ion-exchangers, antacids and as a polymer stabilizer. It is possible to obtain a broad variety of layered double hydroxides (LDHs), depending on the identity and ratio of the cations M2+ and M3+, as well as the interlamelar anion. The aim of this review is to give out some information about this class of materials, concerning to the synthesis, characterization, properties and applications.

Estimating the value of the metal-ligand bond dissociation enthalpy<D> (M-L) for adducts using empirical equations supported by TG data

In this work is presented and tested (for 106 adducts, mainly of the zinc group halides) two empirical equations supported in TG data to estimate the value of the metal-ligand bond dissociation enthalpy for adducts: <D> (M-O) = t i / g if t i < 420 K and <D> (M-O) = (t i / g ) - 7,75 . 10-2 . t i if t i > 420 K. In this empirical equations, t i is the thermodynamic temperature of the beginning of the thermal decomposition of the adduct, as determined by thermogravimetry, andg is a constant factor that is function of the metal halide considered and of the number of ligands, but is not dependant of the ligand itself. To half of the tested adducts the difference between experimental and calculated values was less than 5%. To about 80% of the tested adducts, the difference between the experimental (calorimetric) and the calculated (using the proposed equations) values are less than 15%.

A combustão catalítica do metano: estudo estatístico do efeito das variáveis de preparação e pré-tratamento de catalisadores de paládio suportado sobre a atividade catalítica

The catalytic combustion of methane on alumina supported palladium catalysts was studied. It has been reported that the activity of the catalyst increases with its time on line, despite of an increase of the palladium particle size. However, different preparation, pretreatment and testing conditions can be the reason for the observed different results. An experimental design, which allows to verify the influence of several parameters at the same time with a good statistical quality, was used. A Plackett-Burman design was selected for the screening of the variables which have an effect on the increase of the catalyst activity.

Síntese, caracterização e estudo das propriedades catalíticas e magnéticas de nanopartículas de Ni dispersas em matriz mesoporosa de SiO2

Nickel nanoparticles supported on amorphous silica ceramic matrix were synthesized by the polymeric precursor method. The nanostructure was characterized by NMR, BET, XRD, SEM, TEM, and flame atomic absorption spectrometry techniques. It was observed a dependence of the crystallite size on the thermal annealing, under a N2 atmosphere. The materials presented a high catalytic activity and selectivity upon the beta-pinene hydrogenation reaction. The magnetic hystereses were also correlated with the morphology of the processed material.