Unconfined shear strength of compacted unsaturated plastic soils

A central goal in unsaturated soil mechanics research is to create a smooth transition between traditional soil mechanics approaches and an approach that is applicable to unsaturated soils. Undrained shear strength and the liquidity index of reconstituted or remoulded saturated soils are consistently correlated, which has been demonstrated by many studies. In the liquidity index range from 1 (at w(l)) to 0 (at w(p)), the shear strength ranges from approximately 2 kPa to 200 kPa. Similarly, for compacted soil, the shear strength at the plastic limit ranges from 150 kPa to 250 kPa. When compacted at their optimum water content, most soils have a suction that ranges from 20 kPa to 500 kPa; however, in the field, compacted materials are subjected to drying and wetting, which affect their initial suction and as a consequence their shear strength. Unconfined shear tests were performed on five compacted tropical soils and kaolin. Specimens were tested in the as-compacted condition, and also after undergoing drying or wetting. The test results and data from prior literature were examined, taking into account the roles of void ratio, suction, and relative water content. An interpretation of the phenomena that are involved in the development of the undrained shear strength of unsaturated soils in the contexts of soil water retention and Atterberg limits is presented, providing a practical view of the behaviour of compacted soil based on the concept of unsaturated soil. Finally, an empirical correlation is presented that relates the unsaturated state of compacted soils to the unconfined shear strength.

Effect of Plastic Deformation on the Excess Loss of Electrical Steel

The interpretation of the effect of plastic deformation on the calculated excess loss component (anomalous-loss) supports the concept of loss separation. Magnetic losses and Barkhausen noise of nonoriented electrical steel sheets were measured on Epstein strips taken from a single coil of 0.8% Si nonoriented electrical steel. Sheets were extracted in the annealed condition, without any skin pass and with a grain size of 18 mu m. This material was cold rolled in order to obtain sets of samples with true strain from 2% up to 29%. X-ray diffraction was used to estimate the dislocation density. The analysis of magnetic properties was performed by Barkhausen noise measurements and also by analyzing the hysteresis loops obtained from Epstein frame measurements for different inductions and different frequencies (including the quasi-static regime for hysteresis loss measurements). These data allowed us to observe that most of the well known total loss increase with plastic deformation is due to an increase in the hysteresis loss component, while excess loss decreases to become negligible. This behavior can be explained if it is assumed that the plastic deformation lead to an increase in the number of domain walls per unit volume, thereby decreasing the excess loss. Barkhausen peak area increases with plastic deformation, reproducing results taken from samples of different silicon content.

Steel fiber reinforced concrete pipes: part 1: technological analysis of the mechanical behavior

This paper is the first part of an extensive work focusing the technological development of steel fiber reinforced concrete pipes (FRCP). Here is presented and discussed the experimental campaign focusing the test procedure and the mechanical behavior obtained for each of the dosages of fiber used. In the second part ("Steel fiber reinforced concrete pipes. Part 2: Numerical model to simulate the crushing test"), the aspects of FRCP numerical modeling are presented and analyzed using the same experimental results in order to be validated. This study was carried out trying to reduce some uncertainties related to FRCP performance and provide a better condition to the use of these components. In this respect, an experimental study was carried out using sewage concrete pipes in full scale as specimens. The diameter of the specimens was 600 mm, and they had a length of 2500 mm. The pipes were reinforced with traditional bars and different contents of steel fibers in order to compare their performance through the crushing test. Two test procedures were used in that sense. In the 1st Series, the diameter displacement was monitored by the use of two LVDTs positioned at both extremities of the pipes. In the 2nd Series, just one LVDT is positioned at the spigot. The results shown a more rigidity response of the pipe during tests when the displacements were measured at the enlarged section of the socket. The fiber reinforcement was very effective, especially when low level of displacement was imposed to the FRCP. At this condition, the steel fibers showed an equivalent performance to superior class pipes made with traditional reinforced. The fiber content of 40 kg/m3 provided a hardening behavior for the FRCP, and could be considered as equivalent to the critical volume in this condition.

Steel fibre reinforced concrete pipes. Part 2: numerical model to simulate the crushing test

This paper is part of an extensive work about the technological development, experimental analysis and numerical modeling of steel fibre reinforced concrete pipes. The first part ("Steel fibre reinforced concrete pipes. Part 1: technological analysis of the mechanical behavior") dealt with the technological development of the experimental campaign, the test procedure and the discussion of the structural behavior obtained for each of the dosages of fibre used. This second part deals with the aspects of numerical modeling. In this respect, a numerical model called MAP, which simulates the behavior of fibre reinforced concrete pipes with medium-low range diameters, is introduced. The bases of the numerical model are also mentioned. Subsequently, the experimental results are contrasted with those produced by the numerical model, obtaining excellent correlations. It was possible to conclude that the numerical model is a useful tool for the design of this type of pipes, which represents an important step forward to establish the structural fibres as reinforcement for concrete pipes. Finally, the design for the optimal amount of fibres for a pipe with a diameter of 400 mm is presented as an illustrating example with strategic interest.

Cruising for ocean conservation: no exactly a waste of time. Plastic pollution in the oceans

Grabación realizada por Ciencia compartida (Biblioteca Universitaria)

L'effetto della pressione sulle perdite in condotte con fessure longitudinali - The effect of pressure on leakage in longitudinally crecked pressurized pipes.

La crescente attenzione verso un utilizzo attento, sostenibile ed economicamente efficiente della risorsa idrica rende di primaria importanza il tema delle perdite idriche e della gestione efficiente dei sistemi idrici. La richiesta di controlli dell’uso dell’acqua è stata avanzata a livello mondiale. Il problema delle perdite idriche nei Paesi industrializzati è stato così affrontato con specifiche normative e procedure di best practice gestionale per avanzare una valutazione delle perdite idriche e una limitazione degli sprechi e degli usi impropri. In quest’ambito, la pressione gioca un ruolo fondamentale nella regolazione delle perdite reali. La regolazione delle pressioni nelle diverse ore del giorno consente, infatti, di poter agire su queste ultime perdite, che aumentano all’aumentare della pressione secondo una cosiddetta legge di potenza. La motivazione della presente tesi è originata dalla necessità di quantificare il livello di perdita idrica in un sistema acquedottistico in relazione alla pressione all’interno del sistema stesso. Per avere una stima realistica che vada al di là della legge della foronomia, si vuole valutare l’influenza della deformabilità della condotta in pressione fessurata sull’entità delle perdite idriche, con particolare attenzione alle fessurazioni di tipo longitudinale. Tale studio è condotto tramite l’introduzione di un semplice modello di trave alla Winkler grazie al quale, attraverso un’analisi elastica, si descrive il comportamento di una generica condotta fessurata longitudinalmente e si valuta la quantità d’acqua perduta. I risultati ottenuti in condizioni specifiche della condotta (tipo di materiale, caratteristiche geometriche dei tubi e delle fessure, etc.) e mediante l’inserimento di opportuni parametri nel modello, calibrati sui risultati forniti da una raffinata modellazione tridimensionale agli elementi finiti delle medesime condotte, verranno poi confrontati con i risultati di alcune campagne sperimentali. Gli obiettivi del presente lavoro sono, quindi, la descrizione e la valutazione del modello di trave introdotto, per stabilire se esso, nonostante la sua semplicità, sia effettivamente in grado di riprodurre, in maniera realistica, la situazione che si potrebbe verificare nel caso di tubo fessurato longitudinalmente e di fornire risultati attendibili per lo studio delle perdite idriche. Nella prima parte verrà approfondito il problema della perdite idriche. Nella seconda parte si illustrerà il semplice modello di trave su suolo elastico adottato per l’analisi delle condotte in pressione fessurate, dopo alcuni cenni teorici ai quali si è fatto riferimento per la realizzazione del modello stesso. Successivamente, nella terza parte, si procederà alla calibrazione del modello, tramite il confronto con i risultati forniti da un’analisi tridimensionale agli elementi finiti. Infine nella quarta parte verrà ricavata la relazione flusso-pressione con particolare attenzione all’esponente di perdita, il cui valore risulterà superiore a quello predetto dalla teoria della foronomia, e verrà verificata l’effettiva validità del modello tramite un confronto con i risultati sperimentali di cui è stata fatta menzione in precedenza.

Anisotropy in plastic deformation of extruded magnesium alloy sheet during tensile straining at high temperature

Experimental measurements are used to characterize the anisotropy of flow stress in extruded magnesium alloy AZ31 sheet during uniaxial tension tests at temperatures between 350°C and 450°C, and strain rates ranging from 10-5 to 10-2 s-1. The sheet exhibits lower flow stress and higher tensile ductility when loaded with the tensile axis perpendicular to the extrusion direction compared to when it is loaded parallel to the extrusion direction. This anisotropy is found to be grain size, strain rate, and temperature dependent, but is only weakly dependent on texture. A microstructure based model (D. E. Cipoletti, A. F. Bower, P. E. Krajewski, Scr. Mater., 64 (2011) 931–934) is used to explain the origin of the anisotropic behavior. In contrast to room temperature behavior, where anisotropy is principally a consequence of the low resistance to slip on the basal slip system, elevated temperature anisotropy is found to be caused by the grain structure of extruded sheet. The grains are elongated parallel to the extrusion direction, leading to a lower effective grain size perpendicular to the extrusion direction. As a result, grain boundary sliding occurs more readily if the material is loaded perpendicular to the extrusion direction.

Retention force of plastic clips on implant bars: a randomized controlled trial

Retention of overdentures is important for patients' satisfaction. The study tested whether the clinical performance of retentive clips made of poly-ether-ether-ketone (PEEK) is superior to those made of poly-oxy-methylene (POM).

Extending lifetime of plastic changes in the human brain

The ability of the brain to adjust to changing environments and to recover from damage rests on its remarkable capacity to adapt through plastic changes of underlying neural networks. We show here with an eye movement paradigm that a lifetime of plastic changes can be extended to several hours by repeated applications of theta burst transcranial magnetic stimulation to the frontal eye field of the human cortex. The results suggest that repeated application of the same stimulation protocol consolidates short-lived plasticity into long-lasting changes.