The Good, Bad, and Ugly of Occupational Health Surveillance Part 2: Region 7 OHI Data, Lead, Fatalities, May 21, 2014

A power point made by the IDPH on promoting and protecting the health of Iowans in the workplace.

Effect of a Noise Wall on Snow Accumulation and Air Quality, 1985

A noise wall was investigated to assess its effect on snow accumulation and air quality. Wind tunnel studies were undertaken to evaluate (a) possible snow accumulations and (b) the dispersion of particulate concentrations (dust, smoke, and lead particles) and carbon monoxide. Full-scale monitoring of particulate concentrations and carbon monoxide was performed both before and after the noise wall was constructed. The wind tunnel experiments for snow accumulation were conducted on a model wall located in a flat, unobstructed area. A separated flow zone existed upwind of the wall and snow immediately began to accumulate over most of the separated zone. Having the noise wall in an aerodynamically rough area, such as in an urban area as this one was, substantially decreased the amount of snow collected, compared with in the wind tunnel studies, because of turbulence reducing the separation zone. The snow accumulation has not been significantly greater with the noise wall in place than it was before construction and has proven to be of no concern to date. Monitoring for particulate concentrations has shown that the noise wall has had a beneficial effect because the amount of material collected was reduced. With the noise wall in place, monitoring for carbon monoxide has indicated that (a) for equivalent emissions under conditions of high atmospheric stability and low wind speeds, the carbon monoxide levels would be lower; and (b) under conditions of low atmospheric stability and high wind speeds, the carbon monoxide levels would be higher than expected without the wall in place.

Evaluation of respiratory and dermal occupational exposures to monoethanolamine during cleaning

Professional cleaning is a basic service occupation with a wide variety of tasks carried out in all kind of different sectors and workplaces by a large workforce. One important risk for cleaning workers is the exposure to chemical substances that are present in cleaning products.Monoethanolamine was found to be often present in cleaning products such as general purpose cleaners, bathroom cleaners, floor cleaners and kitchen cleaners. Monoethanolamine can injure the skin, and exposure to monoethanolamine was associated to asthma even when the air concentrations were low. It is a strong irritant and known to be involved in sensitizing mechanisms. It is very likely that the use of cleaning products containing monoethanolamine gives rise to respiratory and dermal exposures. Therefore there is a need to further investigate the exposures to monoethanolamine for both, respiratory and dermal exposure.The determination of monoethanolamine has traditionally been difficult and analytical methods available are little adapted for occupational exposure assessments. For monoethanolamine air concentrations, a sampling and analytical method was already available and could be used. However, a method to analyses samples for skin exposure assessments as well as samples of skin permeation experiments was missing. Therefore one main objective of this master thesis was to search an already developed and described analytical method for the measurement of monoethanolamine in water solutions, and to set it up in the laboratory. Monoethanolamine was analyzed after a derivatisation reaction with o-pthtaldialdehyde. The derivated fluorescing monoethanolamine was then separated with high performance liquid chromatography and detection took place with a fluorescent detector. The method was found to be suitable for qualitative and quantitative analysis of monoethanolamine. An exposure assessment was conducted in the cleaning sector to measure the respiratory and dermal exposures to monoethanolamine during floor cleaning. Stationary air samples (n=36) were collected in 8 companies and samples for dermal exposures (n=12) were collected in two companies. Air concentrations (Mean = 0.18 mg/m3, Standard Deviation = 0.23 mg/m3, geometric Mean = 0.09 mg/m3, Geometric Standard Deviation = 3.50) detected were mostly below 1/10 of the Swiss 8h time weighted average occupational exposure limit. Factors that influenced the measured monoethanolamine air concentrations were room size, ventilation system and the concentration of monoethanolamine in the cleaning product and amount of monoethanolamine used. Measured skin exposures ranged from 0.6 to 128.4 mg/sample. Some cleaning workers that participated in the skin exposure assessment did not use gloves and had direct contact with the solutions containing the cleaning product and monoethanolamine. During the entire sampling campaign, cleaning workers mostly did not use gloves. Cleaning workers are at risk to be regularly exposed to low air concentrations of monoethanolamine. This exposure may be problematic if a worker suffers from allergic reactions (e.g. Asthma). In that case a substitution of the cleaning product may be a good prevention measure as several different cleaning products are available for similar cleaning tasks. Currently there are no occupational exposure limits to compare the skin exposures that were found. To prevent skin exposures, adaptations of the cleaning techniques and the use of gloves should be considered. The simultaneous skin and airborne exposures might accelerate adverse health effects. Overall the risks caused by exposures to monoethanolamine are considered as low to moderate when the cleaning products are used correctly. Whenever possible, skin exposures should be avoided. Further research should consider especially the dermal exposure routes, as very high exposures might occur by skin contact with cleaning products. Dermatitis but also sensitization might be caused by skin exposures. In addition, new biomedical insights are needed to better understand the risks of the dermal exposure. Therefore skin permeability experiments should be considered.

Maternal exposure to polychlorinated biphenyls and the secondary sex ratio: an occupational cohort study.

Background: Though commercial production of polychlorinated biphenyls was banned in the United States in 1977, exposure continues due to their environmental persistence. Several studies have examined the associationbetween environmental polychlorinated biphenyl exposure and modulations of the secondary sex ratio, with conflicting results.Objective: Our objective was to evaluate the association between maternal preconceptional occupational polychlorinated biphenyl exposure and the secondary sex ratio.Methods: We examined primipara singleton births of 2595 women, who worked in three capacitor plants at least one year during the period polychlorinated biphenyls were used. Cumulative estimated maternal occupationalpolychlorinated biphenyl exposure at the time of the infant's conception was calculated from plant-specific job exposure matrices. A logistic regression analysis was used to evaluate the association between maternalpolychlorinated biphenyl exposure and male sex at birth (yes/no).Results: Maternal body mass index at age 20, smoking status, and race did not vary between those occupationally exposed and those unexposed before the child's conception. Polychlorinated biphenyl-exposed mothers were, however, more likely to have used oral contraceptives and to have been older at the birth of their first child than non-occupationally exposed women. Among 1506 infants liveborn to polychlorinated biphenyl-exposedprimiparous women, 49.8% were male; compared to 49.9% among those not exposed (n = 1089). Multivariate analyses controlling for mother's age and year of birth found no significant association between the odds of amale birth and mother's cumulative estimated polychlorinated biphenyl exposure to time of conception.Conclusions: Based on these data, we find no evidence of altered sex ratio among children born to primiparous polychlorinated biphenyl-exposed female workers.

The Child Occupational Self Assessment (COSA, version 2.1) : lasten toimintamahdollisuuksien itsearviointi COSA:n esittely ja suomentamisprosessi

Tämän opinnäytetyön tarkoituksena on aloittaa lapsille ja nuorille suunnatun The Child Occupational Self Assessment (COSA, version 2.1) itsearviointimenetelmän suomenkielisen version käännöstyö. COSA on asiakaslähtöinen itsearviointi, jolla kartoitetaan lasten ja nuorten kokemusta toiminnallisesta pätevyydestään ja jokapäiväisten toimintojen tärkeydestä heille. COSA pohjaa Inhimillisen toiminnan malliin ja sen toteutus seuraa asiakaslähtöistä teoriaa. COSA:n avulla voidaan asettaa toimintaterapialle tavoitteet ja tarkastella niiden toteutumista. Työssämme suomennamme arviointimenetelmän nimen muotoon; Lasten toimintamahdollisuuksien itsearviointi COSA. Arviointimenetelmän käännöstyö tehdään Helsingin ammattikorkeakoulu Stadian toimintaterapian koulutusohjelmalle. Opinnäytetyössä esittelemme ensin arviointia ja tavoitteiden asettamista lasten toimintaterapiassa sekä itsearvioinnin käyttämistä arviointimenetelmänä. Esittelemme COSA itsearviointimenetelmän sekä sen taustalla vaikuttavat Inhimillisen toiminnan mallin sisällön ja asiakaslähtöisyyden. Kartoitamme myös The Child Occupational Self Assessment (COSA, version 2.1 )itsearviointimenetelmän kehittymistä, sitä edeltäneitä arviointimenetelmiä ja COSA:sta aiemmin tehtyjä tutkimuksia. Opinnäytetyössä suomennamme COSA:n arviointilomakkeen. Arviointilomakkeessa on 25 lasten ja nuorten toiminnallista pätevyyttä ja jokapäiväisten toimintojen tärkeyttä kartoittava väittämää. Suomentamisprosessissa selvitämme COSA:n arviointilomakkeen väittämien suomennosten ymmärrettävyyden onnistumista kahdeksan käyttökokeiluun ja haastatteluun osallistuvan lapsen avulla. Saimme arviointilomakkeen suomentamisprosessiin apua neljältä lasten kanssa työskentelevältä toimintaterapeutilta sekä koulutusohjelmamme koulutuspäälliköltä. Käyttökokeiluiden sekä toimintaterapeuttien palautteiden avulla viimeistelimme suomennetun arviointilomakkeen väittämät. Opinnäytetyön lopuksi pohdimme arviointilomakkeen suomentamisprosessin vaiheita sekä mahdollisia jatkotutkimusehdotuksia. Luovutimme Lasten toimintamahdollisuuksien itsearviointi COSA:n arviointilomakkeen koulutusohjelmamme käyttöön ja mahdollisten jatkotutkimusten kohteeksi.

On the thermal noise introduced by a resistor in a circuit

Comentari sobre l'article publicat anteriorment pels mateixos autors: Vargas, M; Pallás, R; The seemingly paradoxical noise behaviour some active circuits. IEEE Transactions on Instrumentation and Measurement. 1994, vol. 43, núm. 5, p. 764-767

Comments on "On resistor-induced thermal noise in linear circuits"

Correspondència referida a l'article de R. Giannetti, publicat ibid. vol.49 p.87-88

SAR Interferometric phase noise reduction using wavelet transform

The problem of synthetic aperture radar interferometric phase noise reduction is addressed. A new technique based on discrete wavelet transforms is presented. This technique guarantees high resolution phase estimation without using phase image segmentation. Areas containing only noise are hardly processed. Tests with synthetic and real interferograms are reported.

Power supply noise and logic error probability

Voltage fluctuations caused by parasitic impedances in the power supply rails of modern ICs are a major concern in nowadays ICs. The voltage fluctuations are spread out to the diverse nodes of the internal sections causing two effects: a degradation of performances mainly impacting gate delays anda noisy contamination of the quiescent levels of the logic that drives the node. Both effects are presented together, in thispaper, showing than both are a cause of errors in modern and future digital circuits. The paper groups both error mechanismsand shows how the global error rate is related with the voltage deviation and the period of the clock of the digital system.

Error probability in synchronous digital circuits due to power supply noise

This paper presents a probabilistic approach to model the problem of power supply voltage fluctuations. Error probability calculations are shown for some 90-nm technology digital circuits.The analysis here considered gives the timing violation error probability as a new design quality factor in front of conventional techniques that assume the full perfection of the circuit. The evaluation of the error bound can be useful for new design paradigms where retry and self-recoveringtechniques are being applied to the design of high performance processors. The method here described allows to evaluate the performance of these techniques by means of calculating the expected error probability in terms of power supply distribution quality.

Occupational exposure to diisononyl phthalate (DiNP) in polyvinyl chloride processing operations

PURPOSE: Diisononyl phthalate (DiNP) is primarily used as a plasticizer in polyvinyl chloride (PVC) materials. While information is available on general population exposure to DiNP, occupational exposure data are lacking. We present DiNP metabolite urinary concentrations in PVC processing workers, estimate DiNP daily intake for these workers, and compare worker estimates to other populations. METHODS: We assessed DiNP exposure in participants from two companies that manufactured PVC materials, a PVC film manufacturer (n = 25) and a PVC custom compounder (n = 12). A mid-shift and end-shift urine sample was collected from each participant and analyzed for the DiNP metabolite mono(carboxy-isooctyl) phthalate (MCiOP). Mixed models were used to assess the effect on MCiOP concentrations of a worker being assigned to (1) a task using DiNP and (2) a shift where DiNP was used. A simple pharmacokinetic model was used to estimate DiNP daily intake from the MCiOP concentrations. RESULTS: Creatinine-adjusted MCiOP urinary concentrations ranged from 0.42-80 μg/g in PVC film and from 1.11-13.4 μg/g in PVC compounding. PVC film participants who worked on a task using DiNP (n = 7) had the highest MCiOP geometric mean (GM) end-shift concentration (25.2 μg/g), followed by participants who worked on a shift where DiNP was used (n = 11) (17.7 μg/g) as compared to participants with no task (2.92 μg/g) or shift (2.08 μg/g) exposure to DiNP. The GM end-shift MCiOP concentration in PVC compounding participants (4.80 μg/g) was comparable to PVC film participants with no task or shift exposure to DiNP. Because no PVC compounding participants were assigned to tasks using DINP on the day sampled, DiNP exposure in this company may be underestimated. The highest DiNP intake estimate was 26 μg/kg/day. CONCLUSION: Occupational exposure to DiNP associated with PVC film manufacturing tasks were substantially higher (sixfold to tenfold) than adult general population exposures; however, all daily intake estimates were less than 25% of current United States or European acceptable or tolerable daily intake estimates. Further characterization of DiNP occupational exposures in other industries is recommended.

Three-Dimensional (3D) Microarchitecture Correlations with 2D Projection Image Gray-Level Variations Assessed by Trabecular Bone Score Using High-Resolution Computed Tomographic Acquisitions: Effects of Resolution and Noise.

The aim of the present study is to determine the level of correlation between the 3-dimensional (3D) characteristics of trabecular bone microarchitecture, as evaluated using microcomputed tomography (μCT) reconstruction, and trabecular bone score (TBS), as evaluated using 2D projection images directly derived from 3D μCT reconstruction (TBSμCT). Moreover, we have evaluated the effects of image degradation (resolution and noise) and X-ray energy of projection on these correlations. Thirty human cadaveric vertebrae were acquired on a microscanner at an isotropic resolution of 93μm. The 3D microarchitecture parameters were obtained using MicroView (GE Healthcare, Wauwatosa, MI). The 2D projections of these 3D models were generated using the Beer-Lambert law at different X-ray energies. Degradation of image resolution was simulated (from 93 to 1488μm). Relationships between 3D microarchitecture parameters and TBSμCT at different resolutions were evaluated using linear regression analysis. Significant correlations were observed between TBSμCT and 3D microarchitecture parameters, regardless of the resolution. Correlations were detected that were strongly to intermediately positive for connectivity density (0.711≤r(2)≤0.752) and trabecular number (0.584≤r(2)≤0.648) and negative for trabecular space (-0.407 ≤r(2)≤-0.491), up to a pixel size of 1023μm. In addition, TBSμCT values were strongly correlated between each other (0.77≤r(2)≤0.96). Study results show that the correlations between TBSμCT at 93μm and 3D microarchitecture parameters are weakly impacted by the degradation of image resolution and the presence of noise.

Estimating the contribution of occupational solar ultraviolet exposure to skin cancer

BACKGROUND: Exposure to solar ultraviolet (UV) light is the main causative factor for skin cancer. Outdoor workers are at particular risk because they spend long working hours outside, may have little shade available and be bound to take their lunch at their workplace. Despite epidemiological evidence of a doubling in risk of squamous cell carcinoma in outdoor workers, the recognition of skin cancer as an occupational disease remains scarce. OBJECTIVE: To assess occupational solar UV doses and its contribution to skin cancer risk. METHODS: A numerical model (SimUVEx) was used to assess occupational and lunch break exposures, characterize exposure patterns and anatomical distribution. Risk of squamous cell carcinoma (SCC) was estimated from an existing epidemiological model. RESULTS: Horizontal body locations received 2.0-2.5 times more UV than vertical locations. Dose associated to lunch outdoor every day was similar to outdoor work one day per week but only half of a seasonal worker. Outdoor workers are associated with an increased risk of SCC but also of frequent acute episodes. CONCLUSION: Occupational solar exposure contributes largely to the overall lifetime UV dose, resulting in an excess risk of SCC. The magnitude of the estimated excess in risk supports the recognition of SCC as an occupational disease.