Laboratory investigation on the effects of overburden pressure, water, and time on slaking induced material property degradation of coal mine spoil

In open-cut strip mining, waste material is placed in-pit to minimise operational mine costs. Slope failures in these spoil piles pose a significant safety risk to personnel, along with a financial risk from loss of equipment and scheduling delays. It has been observed that most spoil pile failures occur when the pit has been previously filled with water and then subsequently dewatered. The failures are often initiated at the base of spoil piles where the material can undergo significant slaking (disintegration) over time due to overburden pressure and water saturation. It is important to understand how the mechanical properties of base spoil material are affected by slaking when designing safe spoil pile slope angles, heights, and dewatering rates. In this study, fresh spoil material collected from a coal mine in Brown Basin Coalfield of Queensland, Australia was subjected to high overburden pressure (0 – 900 kPa) under saturated condition and maintained over a period of time (0 – 6 months) allowing the material to slake. To create the above conditions, laboratory designed pressure chambers were used. Once a spoil sample was slaked under certain overburden pressure over a period of time, it was tested for classification, permeability, and strength properties. Results of this testing program suggested that the slaking of saturated coal mine spoil increase with overburden pressure and the time duration over which the overburden pressure was maintained. Further, it was observed that shear strength and permeability of spoil decreased with increase in spoil slaking.

Role of Melt Convection on the Thermal Performance of Heat Sinks with Phase Change Material

The role of melt convection oil the performance of beat sinks with Phase Change Material (PCM) is presented in this paper. The beat sink consists of aluminum plate fins embedded in PCM and heat flux is supplied from the bottom. The design of such a heat sink requires optimization with respect to its geometrical parameters. The objective of the optimization is to maximize the heat sink operation time for the prescribed heat flux and the critical chip temperature. The parameters considered for optimization are fin number and fill thickness. The height and base plate thickness of heat sink are kept constant in the present analysis. An enthalpy based CFD model is developed, which is capable Of Simulating phase change and associated melt convection. The CFD model is Coupled with Genetic Algorithm (GA) for carrying out the optimization. Two cases are considered, one without melt convection (conduction regime) and the other with convection. It is found that the geometrical optimizations of heat sinks are different for the two cases, indicating the importance of inch convection in the design of heat sinks with PCMs.

Original Pirate Material : Translating Justin Somper's Demons of the Ocean

Tutkielma käsittelee suomentamani Vampiraatit: Kirottujen laiva -nuortenromaanin käännösprosessia. Materiaalina on kustantajalle toimittamani näytekäännös, joka käsittää yhden kokonaisen luvun ja lisäksi kirjan tapahtumiin keskeisesti liittyvän runon. Molemmista tarkastellaan sekä lopullisia, julkaistuja versioita että ensimmäisiä raakaversioita. Julkaistut versiot ovat osa varsinaista tutkielmaa, raakaversiot ja lähtötekstit puolestaan on sisällytetty mukaan liitteinä. Tarkastelunäkökulmani on pääosin deskriptiivinen ja kontrastiivinen. Proosa-analyysi jakautuu kahteen osaan. Ensimmäisessä osassa tutkin tapoja, joilla käännökseni vastustaa ns. lisääntyvän standardisoitumisen lakia (the law of growing standardization), jota Gideon Toury on ehdottanut yleispäteväksi käännöslaiksi. Touryn laki ennustaa, että käännökset ovat useimmiten tyylillisesti alkuteoksiaan latteampia. Esimerkkini kuitenkin osoittavat, että kääntäjän on mahdollista valita ratkaisunsa niin, että latistumiselta vältytään, ainakin silloin, kun lähtöteksti on melko suoraviivaista. Proosa-analyysin jälkimmäinen osa keskittyy käännöksen muokkaamiseen. Vertaan siinä näytekäännös-luvun ensimmäistä versiota julkaistuun versioon ja tutkin muun muassa sitä, missä määrin ensimmäinen versio sisältää lähtökielen interferenssiä, ts. missä määrin englannille tyypilliset rakenteet paistavat siitä läpi. Tarkastelun kohteena ovat myös kohdekieliset kömpelyydet ja niiden poistaminen sekä pienet mutta kokonaisuuden kannalta tärkeät tyylilliset muutokset. Esimerkeistä käy selvästi ilmi kääntämisen prosessimainen luonne. Käännösnäytteeseen sisältyneen runon suomentaminen oli oma erillinen kokonaisuutensa. Tässä osiossa vertailen lähtötekstiä, raakaversiota ja julkaistua käännöstä rinnakkain säkeistö säkeistöltä. Tarkastelussa painottuvat edelleen tekstin muokkaaminen ja hiominen. Analyysien taustaksi esittelen lyhyesti alkuteoksen ja sen kirjoittajan Justin Somperin. Kuvailen myös omaa käännösfilosofiaani ja esittelen kaksi siihen voimakkaasti vaikuttanutta suomentajaa.

Base material characterisation of spoil piles at BMA coal mines

This project was an initiation to investigate slaking induced properties detrition of spoil pile materials with overburden pressure and time. The changes in the material properties over time are important parameters that control the behaviour and performance of the piles. The time dependent mechanical and hydraulic properties reported together with mineralogical changes. One chamber designed to apply slaking in the laboratory and geotechnical investigation conducted to fulfil the objective of this project.

Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242

A new method of modeling material behavior which accounts for the dynamic metallurgical processes occurring during hot deformation is presented. The approach in this method is to consider the workpiece as a dissipator of power in the total processing system and to evaluate the dissipated power co-contentJ = ∫o σ ε ⋅dσ from the constitutive equation relating the strain rate (ε) to the flow stress (σ). The optimum processing conditions of temperature and strain rate are those corresponding to the maximum or peak inJ. It is shown thatJ is related to the strain-rate sensitivity (m) of the material and reaches a maximum value(J max) whenm = 1. The efficiency of the power dissipation(J/J max) through metallurgical processes is shown to be an index of the dynamic behavior of the material and is useful in obtaining a unique combination of temperature and strain rate for processing and also in delineating the regions of internal fracture. In this method of modeling, noa priori knowledge or evaluation of the atomistic mechanisms is required, and the method is effective even when more than one dissipation process occurs, which is particularly advantageous in the hot processing of commercial alloys having complex microstructures. This method has been applied to modeling of the behavior of Ti-6242 during hot forging. The behavior of α+ β andβ preform microstructures has been exam-ined, and the results show that the optimum condition for hot forging of these preforms is obtained at 927 °C (1200 K) and a strain rate of 1CT•3 s•1. Variations in the efficiency of dissipation with temperature and strain rate are correlated with the dynamic microstructural changes occurring in the material.

Field evaluation of micropropagated and conventionally propagated ginger in subtropical Queensland

The growth and performance of micropropagated ginger (Zingiber officinale Roscoe) was compared with 'seed'-derived plants in field trials conducted in south-eastern Queensland. In the first generation ex vitro, micropropagated plants had significantly (P<0.01) reduced rhizome yield with smaller knobs and more roots. Micropropagated plants had a greater (P<0.01) shoot: root (rhizome) ratio compared with seed-derived plants. Shoots from micropropagated plants were also significantly (P<0.01) smaller with a greater number of shoots per plant. The unusual shoot morphology of the micropropagated plants did not appear to be related to the presence of benzylaminopurine, a plant growth hormone added to the multiplication medium, as plants subcultured for 3 cycles on a hormone-free medium also exhibited similar characteristics. Seed collected from the micropropagated plants and seed-derived plants was harvested and, despite the micropropagated seed being significantly (P<0.01) smaller, by the second generation ex vitro there were no significant differences between the treatments. Factors that can improve rhizome size, while reducing production costs, need to be identified before micropropagated plants can be recommended for routine use in the ginger industry as a source of disease and pest-free planting material.

Biomineralization of manganese by Bacillus spp isolated from a marine biofilm

Biomineralization of manganese on titanium condenser material exposed to seawater has been illustrated. Biomineralization occurs when the fouling components, namely, the microbes, are able to oxidize minerals present in water and deposit them as insoluble oxides on biofilm surfaces. Extensive biofilm characterization studies Showed that an alarmingly large number of bacteria in these biofilms are capable of oxidizing manganese and are, thereby, capable of causing biomineralization on the condenser material exposed to seawater. This paper addresses studies on understanding the exact role of the microbes in bringing about oxidation of manganese. The kinetics of manganese oxidation by marine Gram-positive manganese oxidizing bacterium Bacillus spp. that was isolated front the titanium surface was studied in detail. Manganese oxidation in the presence of Bacillus cells, by cell free extract (CFE) and heat-treated cell free extract was also studied. The study confirmed that bacteria mediate manganese oxidation and lead to the formation of biogenic oxides of MnO2 eventually leading to biomineralization on titanium surface exposed to seawater.

Phosphorus nutrition and tolerance of cotton to water stress: II. Water relations, free and bound water and leaf expansion rate

In previous experiments, increased leaf-Phosphorus (P) content with increasing P supply enhanced the individual leaf expansion and water content of fresh cotton leaves in a severely drying soil. In this paper, we report on the bulk water content of leaves and its components, free and bound water, along with other measures of plant water status, in expanding cotton leaves of various ages in a drying soil with different P concentrations. The bound water in living tissue is more likely to play a major role in tolerance to abiotic stresses by maintaining the structural integrity and/or cell wall extensibility of the leaves, whilst an increased amount of free water might be able to enhance solute accumulation, leading to better osmotic adjustment and tolerance to water stress, and maintenance of the volumes of sub-cellular compartments for expansive leaf growth. There were strong correlations between leaf-P%, leaf water (total, free and bound water) and leaf expansion rate (LER) under water stress conditions in a severely drying soil. Increased soil-P enhanced the uptake of P from a drying soil, leading to increased supply of osmotically active inorganic solutes to the cells in growing leaves. This appears to have led to the accumulation of free water and more bound water, ultimately leading to increased leaf expansion rates as compared to plants in low P soil under similar water stress conditions. The greater amount of bound and free water in the high-P plants was not necessarily associated with changes in cell turgor, and appears to have maintained the cell-wall properties and extensibility under water stressed conditions in soils that are nutritionally P-deficient.

Unsteady free Convection MHD Boundary Layer Flow Near a Three-Dimensional Stagnation Point

The unsteady free convection boundary layer hydromagnectic flow near a stagnation point of a three-dimensional body with applied magnetic field and time-dependent wall temperature has been studied. Both semi-semilar and self-similar cases have been considered. The equations governing the above flow have been solved numerically using an implicit finite-difference scheme due to Keller. The magnetic field is found to reduce both the heat transfer and skin friction. The effect of the variation of the wall temperature with time and of mass transfer is found to be more pronounced on the heat transfer than on the skin friction. In self-similar case, for decelerating flow, there is temperature overshoot in the presence of fmagnetic field, but in semi-similar case overshoot occurs even without magnetic field due to the unsteadiness

Det pedagogiska självet : en narrativ studie av direktvalda svensklärarstudenters berättelser

The Pedagogical Self: a narrative study of stories by prospective subject teachers of Swedish The aim of this study is to examine how prospective subject teachers of Swedish experience themselves, their lives and their studies in university context. By answering this question I try to shed light on the pedagogical self of the students, i.e. to reach a deeper understanding of the narrative construction of their teacher identity. My material consists of stories written by one group of students and of transcribed interviews with another group of students at Nordica. All these students have entered both the teacher education programme and studies in their major subject simultaneously, through the so called direct admission. My study focuses on the students first year at the university. I define teacher identity, the pedagogical self, as the part of an individual s self-concept where he/she makes an assessment of himself/herself as a teacher(-to-be). The frame of reference of this interdisciplinary narrative study is founded on phenomenology, hermeneutics, social constructionism and dialogism. The main analysis of the stories is thematic, with the addition of linguistic and metaphorical analysis. With reference to the theories of Paul Ricoeur and Katharine Young, I regard the textual world of the stories as a world of its own. This implies that the researcher can feel free to concentrate on the texts, thus being able to leave the mental processes of the writers disregarded. The theoretician that has influenced my research the most is Max van Manen. He combines a pedagogical attitude with a phenomenological-hermeneutic philosophy. My research results imply that most of these students are drawn to studying Swedish by the clear professional orientation of the studies; their identity as teachers seems to be stronger than their identity as language teachers. The image of a teacher is relatively traditional: a teacher is seen as a self-evident authority, but at the same time as a fostering educator. The students see their studies in a larger perspective: studies as well as the future profession are only one part of life, albeit an important one. Keywords: narrativity, teacher identity

The effect of endophyte on the performance of irrigated perennial ryegrasses in subtropical Australia

The effect of fungal endophyte (Neotyphodium lolii) infection on the performance of perennial ryegrass (Lolium perenne) growing under irrigation in a subtropical environment was investigated. Seed of 4 cultivars, infected with standard (common toxic or wild-type) endophyte or the novel endophyte AR1, or free of endophyte (Nil), was sown in pure swards, which were fertilised with 50 kg N/ha.month. Seasonal and total yield, persistence, and rust susceptibility were assessed over 3 years, along with details of the presence of endophyte and alkaloids in plant shoots. Endophyte occurrence in tillers in both the standard and AR1 treatments was above 95% for Bronsyn and Impact throughout and rose to that level in Samson by the end of the second year. Meridian AR1 only reached 93% while, in the standard treatment, the endophyte had mostly died before sowing. Nil Zendophyte treatments carried an average of ?0.6% infection throughout. Infection of the standard endophyte was associated with increased dry matter (DM) yields in all 3 years compared with no endophyte. AR1 also significantly increased yields in the second and third years. Over the full 3 years, standard and AR1 increased yields by 18% and 11%, respectively. Infection with both endophytes was associated with increased yields in all 4 seasons, the effects increasing in intensity over time. There was 27% better persistence in standard infected plants compared with Nil at the end of the first year, increasing to 198% by the end of the experiment, while for AR1 the improvements were 20 and 134%, respectively. The effect of endophyte on crown rust (Puccinia coronata) infection was inconsistent, with endophyte increasing rust damage on one occasion and reducing it on another. Cultivar differences in rust infection were greater than endophyte effects. Plants infected with the AR1 endophyte had no detectable ergovaline or lolitrem B in leaf, pseudostem, or dead tissue. In standard infected plants, ergovaline and lolitrem B were highest in pseudostem and considerably lower in leaf. Dead tissue had very low or no detectable ergovaline but high lolitrem B concentrations. Peramine concentration was high and at similar levels in leaf and pseudostem, but not detectable in dead material. Concentration was similar in both AR1 and standard infected plants. Endophyte presence appeared to have a similar effect in the subtropics as has been demonstrated in temperate areas, in terms of improving yields and persistence and increasing tolerance of plants to stress factors.

Split-Freedom And Mvd-Intersection - A New Characterization Of Multivalued Dependencies Having Conflict-Free Covers

Sets of multivalued dependencies (MVDs) having conflict-free covers are important to the theory and design of relational databases [2,12,15,16]. Their desirable properties motivate the problem of testing a set M of MVDs for the existence of a confiict-free cover. In [8] Goodman and Tay have proposed an approach based on the possible equivalence of M to a single (acyclic) join dependency (JD). We remark that their characterization does not lend an insight into the nature of such sets of MVDs. Here, we use notions that are intrinsic to MVDs to develop a new characterization. Our approach proceeds in two stages. In the first stage, we use the notion of “split-free” sets of MVDs and obtain a characterization of sets M of MVDs having split-free covers. In the second, we use the notion of “intersection” of MVDs to arrive at a necessary and sufficient condition for a split-free set of MVDs to be conflict-free. Based on our characterizations, we also give polynomial-time algorithms for testing whether M has split-free and conflict-free covers. The highlight of our approach is the clear insight it provides into the nature of sets of MVDs having conflict-free covers. Less emphasis is given in this paper to the actual efficiency of the algorthms. Finally, as a bonus, we derive a desirable property of split-free sets of MVDs,thereby showing that they are interesting in their own right.

Effect of micro-propagation on the health status of strawberry planting material for commercial production of strawberry runners for Queensland

Plant tissue culture has been used for a number of years to produce micropropagated strawberry plants for planting into runner growing beds in the Stanthorpe (Queensland) and Bothwell (Tasmania) regions. This process has allowed the rapid release of new cultivars from the LAWS (Late Autumn, Winter, Spring) breeding program into the current runner production system. Micro-propagation in vitro allows plants to be produced during the autumn and winter months, when mother plants would normally be in a fruit production phase in the field in Queensland. The plants produced are of a high health status when they are planted. The subsequent arrival and build up of various diseases in the runner fields are closely monitored. Using tissue culture for the first generation reduces the time the plants spend in the field by twelve months, reducing disease incidence. To date, any disease outbreak has been successfully managed using early detection and rapid response methods.

In vitro propagation of Corymbia torelliana x C. citriodora (Myrtaceae) via cytokinin-free node culture

Hybrids between Corymbia torelliana (F.Muell.) K.D.Hill & L.A.S.Johnson and C. citriodora subsp. variegata (F.Muell.) A.R.Bean & M.W.McDonald are used extensively to establish forestry plantations in subtropical Australia. Methods were developed for in vitro seed germination, shoot multiplication and plantlet formation that could be used to establish in vitro and ex vitro clone banks of juvenile Corymbia hybrids. Effects of sodium hypochlorite concentration and exposure time on seed contamination and germination, and effects of cytokinin and auxin concentrations on shoot multiplication and subsequent rooting, were assessed. A two-step surface sterilisation procedure, involving 70% ethanol followed by 1% sodium hypochlorite, provided almost no contamination and at least 88% germination. A novel method of cytokinin-free node culture proved most effective for in vitro propagation. Lateral bud break of primary shoots was difficult to induce by using cytokinin, but primary shoots rooted prolifically, elongated rapidly and produced multiple nodes in the absence of exogenous cytokinin. Further multiplication was obtained either by elongating lateral shoots of nodal explants in cytokinin-free medium or by inducing organogenic callus and axillary shoot proliferation with 2.2 µm benzyladenine. Plantlets were produced using an in vitro soil-less method that provided extensive rooting in sterile propagation mixture. These methods provide a means for simultaneous laboratory storage and field-testing of clones before selection and multiplication of desired genotypes.