1.55μm InGaAsP/InP DH激光器中的0.95μm发光带与Auger复合

于2010-11-23批量导入

Tunable MQW-DBR lasers using selective area growth

The tunable ridge waveguide distributed Bragg reflector (DBR) lasers designed for wavelength-division-multiplex (WDM) communication systems at 1.55 um by using selective area growth (SAG) is reported. The threshold current of the DBR laser is 62mA and the output power is more than 8mW. The isolation resistance between the active region and the Bragg region is 30K Ohm. The total tuning range is 6.5nm and this DBR laser can provide 6 continuous standard WDM channels with 100GHz channel spacing; in the tuning range, the single mode suppression ratio (SMSR) is maintained more than 32dB and the maximum output power variation is less than 3dB.

High performance 1.55 mu m InGaAsP/InP strained layer quantum well laser diodes fabricated by MOCVD overgrowth method

High performance uncooled 1.55 mu m InGaAsP/InP strained layer quantum well (SL-QW) lasers grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) were reported in this paper. Whole MOCVD over growth method were applied in this work. The threshold currents of 5mA and the highest lasing temperature of 122 degrees C were obtained.

西藏产雪莲花的化学成分研究

本学位论文报道了作为传统藏药材广泛使用的西藏产雪莲花化学成分的研究。论文由五章组成，第一章是三种西藏产雪莲花的化学成分的系统分离纯化和结构鉴定；第二章为西藏产雪莲花化学成分的液-质及串联质谱联用分析；第三章提出了以HPLC和TLC为检测方法的雪莲花药材质量标准草案；第四章给出了对西藏产雪莲花挥发油化学成分的气-质联用分析结果；第五章概述了雪莲花的化学成分及药理研究进展。 第一章包括三个部分。第一部分报道了绵头雪莲花(Saussurea laniceps Hand.-Mazz.)全草乙醇提取物化学成分的分离鉴定。采用正相硅胶柱层析及凝胶柱层析等分离方法，从西藏产绵头雪莲花的乙醇提取物中共分离鉴定出15个化合物。其中11个化合物为首次从该植物中分离得到，当中2个化合物系在凤毛菊属植物中首次发现。第二部分报道了水母雪莲花(Saussurea medusa Maxim.)全草乙醇提取物的化学成分。采用正、反相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出15个化合物，其中1个为新化合物，另有4个化合物为首次从该植物中分离得到。新化合物结构通过质谱和一维及二维核磁共振等波谱解析方法及碱水解反应确定为巴豆酰基-高车前苷(M-7)。第三部分报道了三指雪莲花 (Saussurea tridactyla Sch.-Bip. ex Hook. f.)全草乙醇提取物的化学成分。采用正相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出7个化合物，其中1个化合物为首次从该植物中分离得到。 第二章也包括三个部分。首先是采用液-质联用(HPLC-DAD-ESI-MSn)分析方法，对7个西藏不同产地的三指雪莲花化学成分进行了分析，通过与标准品的 UV和MS数据比较，共鉴定出14个峰，并对其中8个共有成分进行了定量测定。其次是关于八种西藏产雪莲花化学成分的液-质联用(HPLC-DAD-ESI-MSn)分析，通过与标准品的UV和MS数据比较，共鉴定出15个峰，并对其中8个共有成分进行了定量检测。最后通过对八种西藏产雪莲花主要化学成分的多级串联质谱(ESI-MSn)分析，快速、灵敏地鉴定出10个黄酮和3个香豆素化学成分。 第三章同样包括三个部分。首先是以绵头雪莲花中主要香豆素成分东莨菪素和伞形花内酯为对照品，通过TLC定性检测和HPLC含量测定，草拟出较严谨的药材质量标准。其次是将绵头雪莲花、三指雪莲花和雪兔子作为一个药材看待，草拟了以东莨菪素和伞形花内酯的TLC检测为指标的药材质量标准。最后是针对水母雪莲花，以主要黄酮成分芹菜素-7-O-b-D-葡萄糖苷为对照品作TLC检测，并草拟出该药材的质量标准草案。 第四章报道了西藏产雪莲花挥发油的化学成分分析。采用传统水蒸气蒸馏法分别从八种雪莲花全草中提取挥发油，利用气相色谱-质谱联用技术分别从水母雪莲花、绵头雪莲花、槲叶雪莲花、云状雪兔子、拉萨雪兔子、小果雪兔子、雪兔子和三指雪莲花中分别鉴定出83、83、56、34、21、20、24和20个化学成分，分别占其挥发油总量的70.7%、76.0%、82.2%、55.4%、49.7%、70.4 %、76.2%和 76.7%。 第五章为综述，总结和概括了雪莲花的化学和药理研究进展。 The dissertation reports the investigation of the chemical constituents of the genus Saussurea. Quite a lot of species in this genus are traditional Tibetan medicinal plants, and hence have been widely used in traditional Tibetan medicine. This dissertation consisted of five chapters. The first chapter is on the chemical constituents of three Saussurea plants. The second section is about the analysis of chemical constituents of Saussurea plants using HPLC-MS and ESI-MS/MS. In the third chapter, we proposed quality-control standards for the Genus Saussurea based on TLC (thin layer chromatography) and HPLC. The fourth chapter is about chemical compositions of the essential oil from the whole plant of Saussurea plants. The last chapter reviews the research progress of the Genus Saussurea. The first chapter consists of three parts. The first part is about chemical constituents of ethanol extracts from whole plant of Saussurea laniceps Hand.-Mazz. Fifteen compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. Among them, eleven compounds were isolated from this plant for the first time, and two compounds were isolated from Genus Saussurea for the first time. The second part is about chemical constituents of ethanol extracts from whole plant of Saussurea medusa Maxim. Fifteen compounds were isolated by column chromatography on normal phase, reversed phase silica gel and Sephadex LH-20. Five of them were isolated from this plant for the first time, and there is one new flavonoid glucoside which was identified as 6″-O-crotonoyl-homoplantaginin (M-7) based on the evidence of one- and two-dimensional nuclear magnetic resonance, mass spectrometry analysis, and alkaline hydrolysis reaction. The last part is about chemical constituents of ethanol extracts from whole plant of Saussurea tridactyla Sch.-Bip. ex Hook. f.. Seven compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. There is one compound which was isolated from this plant for the first time. The second chapter consists of three parts. In the first part, we analyzed the chemical constituents of S. tridactyla collected from seven different places in Tibet using HPLC-DAD-ESI-MSn. Fourteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds, among which eight common peaks were quantified. In the second part, we analyzed the chemical constituents of eight Saussurea species using HPLC-DAD-ESI-MSn method. Fifteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds and eight main peaks of them were quantified. In the last part, we analyzed the chemical compounds of the above eight Saussurea plants directly by ESI-MS/MS. Thirteen major compounds, including 10 flavonoids and 3 coumarins were easily rapidly identified. The third chapter consists of three parts. In the first part, we proposed a comparative high quality-control standard for S. laniceps, based on quality detection by TLC and quantity analysis by HPLC using two major compounds (umbelliferone and scopoletin) as standard compounds. In the second part, in viewing S. laniceps, S. tridactyla and S. gossypiphora as the members of one family of medicinal herbs, we suggested a quality-control standard based on the TLC detection of the two major compounds (umbelliferone and scopoletin). In the last part, we proposed a quality-control standard for S. medusa based on the TLC detection of its major component (apigenin 7-O-glucoside). The four chapter analyzed the chemical constituents of essential oil of eight Saussurea species. The essential oils were extracted from the whole plants of these samples with water stream distillation. By GC-MS analysis, we identified eighty-three compounds from S. medusa, eighty-three from S. laniceps, fifty-six from S. quercifolia, thirty-four from S. aster, twenty-one from S. kingii, twenty from S. simpsoniana, twenty-four from S. gossypiphora, and twenty from S. tridactyla respetively, which accounted for 70.7%, 76.0%, 82.2%, 55.4%, 49.7%, 70.4 %, 76.2% and 76.7% of the total essential oil, respectively. The last chapter reviews the research progress of the Genus Saussurea.

水稻同源四倍体三系法杂种优势利用研究

水稻是重要的粮食作物，其产量的增加和品质的改良都是关系国计民生的大事。就我国现阶段的国情而言，水稻产量在现有水平上稳步提升仍是未来十几年甚至几十年农业生产最重要的目标之一。尽管根据“超级杂交水稻育种”的战略设想和水稻育种实践，通过不断地改进育种技术可望在更高的产量水平上进行水稻杂种优势利用，在稻属植物内还具有很大的产量潜力可以挖掘。然而，仅仅从现有的种质基础出发，要更大幅度提高水稻单产，实现“超级杂交稻”的目标也存在一些困难：现有的推广品种是二倍体，尽管种类众多，但是其基因组的来源相对单一；同时，水稻基因组DNA含量也是作物中最少的，基因组内寻求开发潜力有一定困难；水稻作为C3植物，光合利用效率不高也是制约水稻产量提高的因素之一。因此，寻求常规手段以外的技术突破或者方法创新，是实现“超级杂交稻”的目标的迫切需求。本研究利用秋水仙素能抑制细胞分裂中纺锤丝的收缩、使细胞染色体加倍的作用，对水稻幼穗诱导的愈伤组织细胞进行加倍，并分化出再生植株；创制出水稻同源四倍体新的种质材料，在此基础上选育水稻同源四倍体雄性不育三系材料，并实现水稻同源四倍体的三系配套，开展水稻同源四倍体杂种优势利用和四倍体杂交水稻选育研究，建立水稻同源四倍体杂种优势利用的新技术体系。这不仅有助于倍性水平杂种优势的开拓和利用，同时也将为我国新世纪“超级稻”育种研究开辟一条新的技术途径。 水稻幼穗诱导愈伤组织并分化成苗是一项成熟、简单的组织培养技术。本研究以普通二倍体水稻亲本为材料，用秋水仙素进行水稻的多倍体化诱导，创制同源四倍体水稻三系亲本材料并对其进行鉴定。多倍体化以秋水仙素诱导的愈伤组织培养为基础，研究不同秋水仙素浓度梯度和愈伤组织诱导培养基组合对诱导四倍体植株的影响。结果表明在MS+2,4 D 1.0mg/L+ KT0.2mg/L+ IAA0.2mg/L 和500mg/L的秋水仙素处理下，水稻愈伤组织染色体加倍（有最高的效率）效果较好，平均加倍频率可达25.26%，其中，材料CDR22和IR26诱导较易成功，加倍频率分别达到75%和26.5%；相对材料94109 1.3%加倍频率和冈46B 10.8%加倍频率，诱导率差异极显著。 对水稻四倍体材料进行了形态学鉴定结果表明，与二倍体水稻对照相比其株高、穗长、花粉育性等主要农艺性状，确定四倍体材料在穗长和千粒重两方面极显著提高，种子的长度和宽度也显著增长。对花粉育性鉴定，确认水稻四倍体不育系材料仍为不育，保持系材料自交和杂交可育，恢复系材料自交和杂交可育。对四倍体材料进行细胞形态、染色体数目等方面进行细胞学鉴定，经核型分析表明水稻四倍体材料具有48条染色体，是二倍体水稻的两倍。水稻四倍体材料根尖分生组织细胞与二倍体的根尖分生组织细胞相比，细胞体积、细胞核和核仁显著增大。四倍体三系材料在细胞有丝分裂中期均可规则排列在赤道板，并能均等地移向两极；后期观察中没有发现染色体分离滞后现象，分裂末期细胞能够形成大小相对均一的子细胞。水稻同源四倍体三系材料细胞分裂未见异常，植株生长发育正常。 从1996年至2006年，针对结实率、有效分蘖、着粒数和穗长等主要农艺性状，通过系谱选育的方法，对培育的同源四倍体水稻亲本材料进行了连续选择和改良，取得较好成效。表现为结实率的改良效果极佳，所有改良材料的平均结实率均呈上升趋势，如D237（29.70％→72.70％）、DTB（19.55％→53.21％）等。有效分蘖总体呈现上升趋势，但在不同的年份，如1998和2002存在较大的负向波动。部分材料改良效果明显，如D19B（5.87→13.50）、D什香 (7.00→12.00)等；同时一些材料如DTB和D明恢63虽然总体略有提高，但在不同的年份波动很大，因此存在较大改良阻力，原因还有待进一步研究。着粒数的改良上升趋势比较显著，除保持系的DTB之外，其余材料的平均着粒数有显著提高。穗长的改良阻力较大，虽然不同材料总体上有所提高，但效果并不显著，并且不同年份有较大负向波动（2001）。此外还对株高、剑叶长等性状也进行了选择，但效果不显著，原因有待进一步提高。同源四倍体材料产量相关性状遗传改良幅度不一致，保持系和恢复系间的遗传改良效果也存在差异。这为同源四倍体水稻的进一步利用打下了良好的基础。 籼稻和粳稻亚种间杂交及杂种优势利用的主要障碍就是其低的结实率。而同源四倍体杂交水稻的研究为提高杂交水稻的杂种优势利用创造了新的途径。本研究通过随机区组设计方案，挑选性状优良的二倍体水稻材料，包括雄性不育系，保持系和恢复系进行秋水仙素诱导加倍，从而获得同源四倍体水稻对应的三系材料。利用选育的优良水稻同源四倍体三系材料，配制7个杂交组合，杂交F1代与其恢复系亲本进行比较，用于计算超亲优势（HB）；而杂交F1代与生产上大面积推广的二倍体杂交品种汕优63进行比较，用于计算杂种优势。结果显示，同源四倍体杂交水稻的超亲优势表现为：每株有效穗变化幅度为1.4%至105.9%，总粒数为0.5%至74.3%，每穗实粒数为17.6%至255.7%，结实率为9.6%至130.4%。这些农艺性状的改良使得这7个杂种F1的理论产量的超亲优势高达64.8%至672.7%。小区试验中四倍体杂交水稻组合T461A/T4002和T461A/T4193分别比二倍体对照汕优63提高46.3%和38.3%以上，除一个品种以外所有品种产量均接近或高于汕优63的产量。同源四倍体水稻强大的杂种优势表明，亚种间杂交育性低的问题可通过四倍体化及强化选择来解决。此外，同源四倍体杂交水稻器官的巨大性也是其产量提高的有利因素，水稻同源四倍体三系杂种优势利用研究具有一定的理论价值和商业生产潜力。 Rice is one of the major food crops, the improvement of the production and quality of it is an important thing related to the people's livelihood. On China's current national conditions, steadily increase of the rice yield based on the current level is still one of the most important goals in the next decade or even decades of agricultural production. According to the "super hybrid rice breeding" the strategic and rice breeding practice, improvement of the use of hybrid rice heterosis through continuous improvements in breeding technology is expected to get a higher level of rice yield, there are also a great yield potential can be exploited. However, there are also some difficulties to increase rice yield obviously and implement the goal of "super hybrid rice" based on the existing germplasm: Rice varieties in promotion are diploid, although there are many varieties, but their genome are from a comparatively single source; Meanwhile, the rice genome DNA are the least among the crops, it is difficult to exploit the development potential within the genome; Rice as C3 plants, photosynthetic efficiency is not high, it is one of the factors constraint rice yield. Therefore, seeking technological breakthroughs or innovative methods different from conventional means is the urgent needs to reach the target of "super hybrid rice". Using colchicine inhibit spindle contraction during cell division, double the cell chromosome, we induced callus cells from rice panicle to be doubled, and differentiated regeneration; we created a new autotetraploid rice germplasm material, and on that basis we bred male sterility three line autotetraploid rice materials, and the achieved the three line rice autotetraploid matchmaking, researched in autotetraploid rice heterosis usage and tetraploid hybrid rice breeding, constituted a new technology system of autotetraploid hybrid rice heterosis utilization. This not only helps the tetraploid rice heterosis exploration and use, but also inaugurates a new technical means for China in the new century "super rice" breeding research. We chose ordinary diploid rice as materials, using colchicine to induce the polyploidization, created the autotetraploid rice three-line materials and identified them. The polyploidization was based on the colchicine-induced callus tissue culture, and we experimented different colchicine concentrations and culture mediums to induce tetraploid plants, confirmed that the optimal concentration for inducement was 500 mg/L, the average induce rate was 25.26 %. Among all the materials, CDR22 and IR26 had higher induced rate; in contrary, 94109 and GANG46B had lower induced rate, the difference was significant. Autotetraploid materials was identified of both morphological and cytological, compared plant height, length of pollen sterility, and other major agronomic traits with a diploid rice as the control plant, identified that the autotetraploid materials had very significant advantages in ear length and thousand-grain weight, as well as the size of the seeds. Cytology identification included observation of the cell morphology, the number of chromosomes, and karyotype analysis on the autotetraploid materials confirmed that their chromosome number was 48, twice of the diploid rice. Mitoses in the three lines were common: chromosomes arrayed normally in metaphase and separated balanced into the two poles, chromosome moved without lagging in anaphase and daughter cells normally formed in telophase except one. It has been proved that tetraploid rice has normal meiosis as their diploid relatives, which usually including series of sub-phases as interphase, prophase I (five sub-phases), prophase II, metaphase I, II, anaphase I, II and telophase I, II. However, abnormal phenomena, such as formation of tetravalent, trivalent and univalent, chromosome lagging and so on, which would finally block meiosis. Configurations of chromosome in metaphaseⅠwere versatile in structure and form accept the bivalent. That condition varied in different strain, suggesting more complex paring configurations and more versatile genetic characters in tetraploid rice. All these abnormalities in meiosis contributed to low fertility of gamete and might consequently resulted in low seed setting. Successive selection and improvement on seed set, productive tiller per plant, total grains per panicle, panicle length and so on had been carried out from 1996 to 2006. The raise of seed sets was significant in both restorers and maintainers. Seed sets of some strains were improved more significantly than others, for example D237（29.70％→72.70％）、DTB（19.55％→53.21％）and et al.. Productive tiller per plant was improved to some extant. The tendency of improvement was rising on the whole but changed in some years such as 1998 and 2002. Part of the stains increased greatly, such as D19B（5.87→13.50）、Dshixiang (7.00→12.00) and so on, but some strains including DTB and Dminghui63 only increased little and decreased in some years by unknown reason. Total grains per panicle increased significantly and all strains except DTB increased. Improvement of panicle length termed to be hard. Different strains showed different capacities for improvement and floating existed in different years for example 2001. It has been proved that other agronomical traits including plant length, flag leaf length and so on could be improved but not significantly by selection also. In a word, agronomical traits could be raised by successive selection that is prerequisite for further utility of autotetraploid rice. Poor fertility is the main barrier for utilizing heterosis between the two rice (Oryza stiva L.) sub-species, indica and japonica. Recently, the development of autotetraploid hybrids (2n=4x=48) has been suggested as a new method for increasing heterosis in hybrid rice. Using standard experimental protocols, the elite diploid rice male sterile, maintainer, and restorer lines were colchine-doubled and autotetraploid counterparts were obtained. Seven resulting hybrids were analyzed for heterobeltiosis (HB), where the F1 was compared to the male parent, and the degree of heterosis, where the F1 was compared to the diploid commercial hybrid, Shanyou 63. The HB among the autotetraploid hybrids ranged from 1.4 to 105.9% for the productive panicles per plant, 0.5 to 74.3% for total kernels per panicle, 17.6 to 255.7% for filled kernels per panicle, and 9.6 to 130.4% for seed set. Improvements in these yield components resulted in the HB for kernel yield ranging from 64.8 to 672.7% among the seven hybrids. Hybrids T461A/T4002 and T461A/T4193 yielded 46.3 and 38.3% more, respectively than Shanyou 63, and all other hybrids but one yielded the same or more than Shanyou 63. The high heterosis for yield suggests that hybrid sterility between two rice sub-species may be overcome by using tetraploid lines followed by intensive selection. Also, the gigantic features of the autotetraploid hybrids may establish a plant structure able to support the higher yield.

制革废水生物强化处理及中水回用试验研究

制革行业是轻工行业中仅次于造纸业的高耗水、重污染行业，作为劳动密集型行业，在解决大量人口就业问题的同时，也对所在地区环境造成了严重污染。目前我国制革行业每年排放废水8,000~12,000万吨，废水中含铬约3,500 t，SS为1.2×105 t，COD为1.8×105 t，BOD为7×104 t，对水体污染严重。 本研究在对厌氧酸化工艺进行研究、一级好氧处理段进行工艺比选研究的基础上，获得了匀质调节—SBBR—BAF的生物处理工艺，并依托该工艺进行了生物强化处理的研究，考察了菌剂的强化运行效果及其处理水回用的可行性。 研究表明，在进水COD＞3,000 mg/L，厌氧酸化具有很好的抗冲击作用，保证了好氧工艺出水COD＜200 mg/L；在进水COD＜3,000 mg/L，可只通过好氧处理实现出水COD＜200 mg/L。厌氧酸化停留时间选择不当，会导致厌氧出水硫化物浓度升高，严重影响好氧系统，会使好氧活性污泥因中毒而解絮。 研究表明，当进水COD为2,000~2,500 mg/L，NH4+-N为130~146 mg/L时，COD、NH4+-N去除率SBBR分别为93.8%~96.6%和14.5%~55.9%，SBR分别为88.8%~94.9%和13%~50.7%，表明SBBR优于SBR。同时，研究发现SBBR污泥增长率为0.05 kgVSS/kgCOD，仅为SBR0.57 kgVSS/kgCOD的8.8%。此外，研究发现SBBR在停止运行后经3个运行周期可回复原油能力，而SBR池经9个周期培养也不能恢复，说明SBBR恢复能力明显优于SBR。 研究表明，以匀质调节—SBBR—BAF为主的制革废水处理工艺，出水水质稳定，进水COD 801~2,834 mg/L、NH4+-N 87~203 mg/L，出水COD＜80 mg/L、NH4+-N＜10 mg/L，基本达到中水回用标准；操作简单灵活，没有污泥回流系统，污泥产率低，污泥处理费用低；工艺基本不需要添加化学药剂，既节约成本、又避免了二次污染；两级生物膜使得该工艺具有很强的耐冲击负荷能力，特别适合制革废水水质水量波动大的特点。 研究表明，高效菌对系统的启动具有一定的促进作用，强化系统生物膜6天可以成熟，对照系统生物膜9天可以成熟。同时高效菌能加速COD降解，缩短停留时间，强化系统6~8 h可使COD＜200 mg/L，对照系统8~10 h可使COD＜200 mg/L。长期运行表明，强化系统的SBBR在COD和NH4+-N的去除率都优于对照系统的SBBR。最终出水COD强化系统平均为53 mg/L、对照系统为74 mg/L。在模拟循环过程中，强化系统均有更高的稳定性。可实现8次理论循环，而对照系统只能实现4次理论循环。 研究表明，通过合理的工艺设计，可以实现猪皮制革废水达到《污水综合排放标准GB8976-1996》一级标准，同时满足工厂部分用水要求。通过添加高效微生物，可提高生物处理系统处理能力，使处理水能够满足工厂的多次回用。 As a labour-intensive industry, tanning has created large amount of working opportunities as well as caused severe contamination to environment. And it is one of the highest water-consuming and polluting industry, only second to manufacturing. At present time, Chinese leather industry emits wastewater about 80,000,000~120,000,000 t annually, which contains chromium about 3,500 t, SS 1.2×105 t, COD 1.8×105 t, BOD 7×104 t and ambient riverhead has been polluted greatly. Based on the research of anaerobic acidification and comparison of SBBR and SBR, biotreatment process (Homogenization—SBBR—BAF) had been established to amend the disadvantages of traditional sewage treatment such as too much sludge, high cost of advanced treatment and NH4+-N can not reach the emission standard. Research on the bioaugmentation was also been carried out. Researches showed, when COD of influent was beyond 3,000 mg/L, anaerobic acidification could resist strong impact, thus COD of effluent was less than 200 mg/L; when COD of influent was less than 3,000 mg/L, only throughout aerobic sewage treatment could COD of effluent beless than 200 mg/L. False residence tiome of anaerobic acidification would lead to the higher effluent concentration of sulfide and disintegration of aerobic activated sludge. Researches showed SBBR worked a better than SBR: when influent between 2,000 and 2,500 mg/L, NH4+-N between 130 mg/L and 146 mg/L, COD, NH4+-N removal rate of SBBR was 93.3%~96.6%, 14.5%~55.9% respectively while COD, NH4+-N removal rate of SBR was 88.8%~94.9%, 13%~50.7% respectively. Sludge growth rate of SBBR was 8.8% of that of 0.05 kgVSS/kgCOD. Besides, SBBR could recovered after 3 operating periods while SBR worked no better after 9 operating periods.Therefore, SBBR excelled SBR. Researches showed, effluent quantity of tannery wastewater treatment process (Homogenization—SBBR—BAF) was stable. When COD of influent was between 801 and 2,834 mg/L, NH4+-N was between 87 mg/L and 203 mg/L, COD of effluent was less than 80 mg/L, NH4+-N was less than 10 mg/L, which achieved the standard of reuse. This biotreatment was featured in low cost, easy and flexible management, less sludge, no inverse sludge system. Besides, this technique required no chemical, which could lower the cost and avoid secondary pollution. Great resistant of impact due to two membranes and was suitable for tannery wastewater which was featured by fluctuation of influent quality and quantity. Researches showed effective microorganisms promotes the startup of the process.Biofilm in the bioaugmentation process matured with 6 days while biofilm in normal process matured with 9 days. Effective microorganisms could accelerate the degradation of COD and shorten the residence time. Aggrandizement system could make COD<200 mg/L with 6 to8 hours while cntrolling system could make COD<200 mg/L with 8 to 10 hours. Long-term operating shows that SBBR in the bioaugmentation system worked better than the normal system in the treatment of COD and NH4+-N. The average COC of effluent in bioaugmentation system was 53 mg/L, normal system was 74 mg/L. In the simulative circulation process,aggrandizement process, which could fulfill 8 times theoretical circulation, works more stably than controlling process which could only fulfill 4 times theoretical circulation. Researches showed that reasonable design could make the wastewater meet the first grade of discharging standard of National Integrated Wastewater Discharge Standard (GB8976-1996), and partially meet the demand of water using of the factory. Adding effective microorganisms could enhance the biotreatment and make the effluents reuse many times.

5×5阵列PHOSWICH闪烁探测器望远镜

描述了一个 5× 5阵列带电粒子 PHOSWICH闪烁探测器望远镜结构。它的每一个单元由 1片厚度为 1mm,面积为 2 4 mm× 2 4 mm快塑料闪烁体 NE10 2 A和 1个前表面为 2 4 mm× 2 4 mm,后表面为 37mm×37mm,厚度为 4 0 mm的 Cs I( Tl)晶体组成的。在兰州放射性离子次级束流线 ( RIBL L )上测试到 Z/ΔZ =2 0

Effect of 80.55 MeV/u(12)C(6+) ions on radiosensitivity and cell cycle of human hepatoma cell lines

In this paper, the relationship between radiosensitivity, cell cycle alteration and the change of apoptosis in different human hepatoma cell lines irradiated by heavy ions were studied with the aim of building up the base data for clinical therapy. Exponentially growing hepatoma cell lines were irradiated by 80.55 MeV/u(12)C(6+) ions at a dose of 0 Gy, 0.5 Gy, 1 Gy, 2 Gy, 4 Gy and 8 Gy. The radiosensitivity was assessed by means of the colony-forming assay. The DNA content, the percentage of each cell-cycle phase and the apoptosis rate were obtained with flow cytometry methods. After the irradiation, the SF2 (survival fraction at 2 gray) of SMMC-7721 cells were evidently lower than that of HepG2 cells. The S phase arrest, G2/M phase arrest delay and the apoptosis in the two hepatoma cell lines varied with the increase of the dose and repair time. The heavy ions could obviously kill the human hepatoma cell lines. Compared to HepG2 cells, SMMC-7721 cells were more radiosensitive to C-12(6+) ions.

Low-temperature heat capacities and standard molar enthalpy of formation of aspirin

Molar heat capacities (C-p,C-m) of aspirin were precisely measured with a small sample precision automated adiabatic calorimeter over the temperature range from 78 to 383 K. No phase transition was observed in this temperature region. The polynomial function of Cp, vs. T was established in the light of the low-temperature heat capacity measurements and least square fitting method. The corresponding function is as follows: for 78 Kless than or equal toTless than or equal to383 K, C-p,C-m/J mol(-1) K-1=19.086X(4)+15.951X(3)-5.2548X(2)+90.192X+176.65, [X=(T-230.50/152.5)]. The thermodynamic functions on the base of the reference temperature of 298.15 K, {DeltaH(T)-DeltaH(298.15)} and {S-T-S-298.15}, were derived.

Low-temperature heat capacity and standard molar enthalpy of formation of 9-fluorenemethanol (C14H12O)

Low-temperature heat capacities of the 9-fluorenemethanol (C14H12O) have been precisely measured with a small sample automatic adiabatic calorimeter over the temperature range between T = 78 K and T = 390 K. The solid-liquid phase transition of the compound has been observed to be T-fus = (376.567 +/- 0.012) K from the heat-capacity measurements. The molar enthalpy and entropy of the melting of the substance were determined to be Delta(fus)H(m) = (26.273 +/- 0.013) kJ (.) mol(-1) and Delta(fus)S(m) = (69.770 +/- 0.035) J (.) K-1 (.) mol(-1). The experimental values of molar heat capacities in solid and liquid regions have been fitted to two polynomial equations by the least squares method. The constant-volume energy and standard molar enthalpy of combustion of the compound have been determined, Delta(c)U(C14H12O, s) = -(7125.56 +/- 4.62) kJ (.) mol(-1) and Delta(c)H(m)degrees(C14H12O, s) = -(7131.76 +/- 4.62) kJ (.) mol(-1), by means of a homemade precision oxygen-bomb combustion calorimeter at T = (298.15 +/- 0.001) K. The standard molar enthalpy of formation of the compound has been derived, Delta(f)H(m)degrees (C14H12O, s) = -(92.36 +/- 0.97) kJ (.) mol(-1), from the standard molar enthalpy of combustion of the compound in combination with other auxiliary thermodynamic quantities through a Hess thermochemical cycle. (C) 2004 Elsevier Ltd. All rights reserved.