Medidas de concentração de radônio proveniente de argamassas de cimento portland, gesso e fosfogesso

Portland cement being very common construction material has in its composition the natural gypsum. To decrease the costs of manufacturing, the cement industry is substituting the gypsum in its composition by small quantities of phosphogypsum, which is the residue generated by the production of fertilizers and consists essentially of calcium dihydrate and some impurities, such as fluoride, metals in general, and radionuclides. Currently, tons of phosphogypsum are stored in the open air near the fertilizer industries, causing contamination of the environment. The 226 Ra present in these materials, when undergoes radioactive decay, produces the 222Rn gas. This radioactive gas, when inhaled together with its decay products deposited in the lungs, produces the exposure to radiation and can be a potential cause of lung cancer. Thus, the objective of this study was to measure the concentration levels of 222Rn from cylindrical samples of Portland cement, gypsum and phosphogypsum mortar from the state of Paraná, as well as characterizer the material and estimate the radon concentration in an environment of hypothetical dwelling with walls covered by such materials. Experimental setup of 222Rn activity measurements was based on AlphaGUARD detector (Saphymo GmbH). The qualitative and quantitative analysis was performed by gamma spectrometry and EDXRF with Au and Ag targets tubes (AMPTEK), and Mo target (ARTAX) and mechanical testing with x- ray equipment (Gilardoni) and the mechanical press (EMIC). Obtained average values of radon activity from studied materials in the air of containers were of 854 ± 23 Bq/m3, 60,0 ± 7,2 Bq/m3 e 52,9 ± 5,4 Bq/m3 for Portland cement, gypsum and phosphogypsum mortar, respectively. These results extrapolated into the volume of hypothetical dwelling of 36 m3 with the walls covered by such materials were of 3366 ± 91 Bq/m3, 237 ± 28 Bq/m3 e 208 ± 21 Bq/m3for Portland cement, gypsum and phosphogypsum mortar, respectively. Considering the limit of 300 Bq/m3 established by the ICRP, it could be concluded that the use of Portland cement plaster in dwellings is not secure and requires some specific mitigation procedure. Using the results of gamma spectrometry there were calculated the values of radium equivalent activity concentrations (Raeq) for Portland cement, gypsum and phosphogypsum mortar, which were obtained equal to 78,2 ± 0,9 Bq/kg; 58,2 ± 0,9 Bq/kg e 68,2 ± 0,9 Bq/kg, respectively. All values of radium equivalent activity concentrations for studied samples are below the maximum level of 370 Bq/kg. The qualitative and quantitative analysis of EDXRF spectra obtained with studied mortar samples allowed to evaluate quantitate and the elements that constitute the material such as Ca, S, Fe, and others.

Estudo da influência da morfologia de nanopartículas de sílica mesoporosa na liberação do anticancerígeno indol-3-carbinol

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Ceilândia, Programa de Pós-graduação em Ciências e Tecnologias em Saúde, 2015.

Sinterização de Ce1-XEuXO2-(X/2) para aplicação como eletrólito sólido em células a combustível de temperaturas intermediárias

Given the environmental concern over global warming that occurs mainly by emission of CO2 from the combustion of petroleum, coal and natural gas research focused on alternative and clean energy generation has been intensified. Among these, the highlight the solid oxide fuel cell intermediate temperature (IT-SOFC). For application as electrolyte of the devices doped based CeO2 with rare earth ions (TR+ 3) have been quite promising because they have good ionic conductivity and operate at relatively low temperatures (500-800 ° C). In this work, studied the Ce1-xEuxO2-δ (x = 0,1, 0,2 and 0,3), solid solutions synthesized by the polymeric precursor method to be used as solid electrolyte. It was also studied the processing steps of these powders (milling, compaction and two step sintering) in order to obtain dense sintered pellets with reduced grain size and homogeneous microstructure. For this, the powders were characterized by thermal analysis, X-ray diffraction, particle size distribution and scanning electrons microscopy, since the sintered samples were characterized by dilatometry, scanning electrons microscopy, density and grain size measurements. By x-ray diffraction, it was verified the formation of the solid solution for all compositions. Crystallites in the nanometric scale were found for both sintering routes but the two step sintering presented significant reduction in the average grain size

Caracterização de atapulgita visando aplicação para reforço de materiais poloméricos

The clay mineral attapulgite is a group of hormitas, which has its structures formed by microchannels, which give superior technological properties classified the industrial clays, clays of this group has a very versatile range of applications, ranging from the drilling fluid for wells oil has applications in the pharmaceutical industry. Such properties can be improved by activating acid and / or thermal activation. The attapulgite when activated can improve by up to 5-8 times some of its properties. The clay was characterized by X-ray diffraction, fluorescence, thermogravimetric analysis, differential thermal analysis, scanning electron microscopy and transmission electron microscopy before and after chemical activation. It can be seen through the results the efficiency of chemical treatment, which modified the clay without damaging its structure, as well as production of polymer matrix composites with particles dispersed atapugita

Desenvolvimento de bloco de vedação com barita na composição de partida para blindagem de radiação X

This work main objective is to study the use of bricks in barium X-rays rooms in order to contribute to the optimization of shielding rooms diagnosis. The work was based on experimental measurements of X-ray attenuation (40 to 150 kV), using ceramic seal bearing the incorporation of barium sulfat (BaSO4). Different formulations were studied in three different firing temperatures and evaluated for incorporation in the ceramic body. The composition of 20% of barite processed at a temperature of 950 ° C showed better physical and mechanical properties, is considered the most suitable for the purpose of this work. Were produced bricks sealing composition formulated based on that presented the best technological features. These blocks were tested physically as a building material and wall protective barrier. Properties such as visual, deviation from the square, face flatness, water absorption and compressive strength were evaluated for all the blocks produced. The behavior of this material as attenuator for X-rays was investigated by experimental results which take into account mortar manufacturers barium through the different strains and compared with the reference material (Pb). The simulation results indicated that the ceramic block barium shows excellent properties of attenuation equivalence lead taking into account the energy used in diagnostic X-ray

Remoção de metais pesados em efluentes sintéticos utilizando vermiculita como adsorvente

Heavy metals are used in many industrial processestheirs discard can harm fel effects to the environment, becoming a serious problem. Many methods used for wastewater treatment have been reported in the literature, but many of them have high cost and low efficiency. The adsorption process has been used as effective for the metal remoal ions. This paper presents studies to evaluate the adsorption capacity of vermiculite as adsorbent for the heavy metals removal in a synthetic solution. The mineral vermiculite was characterized by differents techniques: specific surface area analysis by BET method, X-ray diffraction, raiosX fluorescence, spectroscopy in the infraredd region of, laser particle size analysis and specific gravity. The physical characteristics of the material presented was appropriate for the study of adsorption. The adsorption experiments weredriveal finite bath metod in synthetic solutions of copper, nickel, cadmium, lead and zinc. The results showed that the vermiculite has a high potential for adsorption, removing about 100% of ions and with removal capacity values about 85 ppm of metal in solution, 8.09 mg / g for cadmium, 8.39 mg/g for copper, 8.40 mg/g for lead, 8.26 mg/g for zinc and 8.38 mg/g of nickel. The experimental data fit in the Langmuir and Freundlich models. The kinetic datas showed a good correlation with the pseudo-second order model. It was conducteas a competition study among the metals using vermiculiti a adsorbent. Results showed that the presence of various metals in solution does not influence their removal at low concentrations, removing approximat wasely 100 % of all metals present in solutions

Caracterização microestrutural e elétrica de La(FexNi1-x)O3 sintetizado pelo método da gelatina

The present work deals with the synthesis of materials with perovskite structure with the intention of using them as cathodes in fuel cells SOFC type. The perovskite type materials were obtained by chemical synthesis method, using gelatin as the substituent of citric acid and ethylene glycol, and polymerizing acting as chelating agent. The materials were characterized by X-ray diffraction, thermal analysis, spectroscopy Fourier transform infrared, scanning electron microscopy with EDS, surface area determination by the BET method and Term Reduction Program, TPR. The compounds were also characterized by electrical conductivity for the purpose of observing the possible application of this material as a cathode for fuel cells, solid oxide SOFC. The method using gelatin and polymerizing chelating agent for the preparation of materials with the perovskite structure allows the synthesis of crystalline materials and homogeneous. The results demonstrate that the route adopted to obtain materials were effective. The distorted perovskite structure have obtained the type orthorhombic and rhombohedral; important for fuel cell cathodes. The presentation material properties required of a candidate cathode materials for fuel cells. XRD analysis contacted by the distortion of the structures of the synthesized materials. The analyzes show that the electrical conductivity obtained materials have the potential to act as a cell to the cathode of solid oxide fuel, allowing to infer an order of values for the electrical conductivities of perovskites where LaFeO3 < LaNiO3 < LaNi0,5Fe0,5O3. It can be concluded that the activity of these perovskites is due to the presence of structural defects generated that depend on the method of synthesis and the subsequent heat treatment

Desenvolvimento de filtros cerâmicos impregnados com nanopartículas de prata para desinfecção de água potável

Brazil has vast amounts of hydric resources, whose quality has been deteriorating due to pollutant dumping. Household waste disposal is one of the main sources of water pollution, stimulating bacteria proliferation and introducing microorganisms, including those from fecal matter. Conventional water disinfection methods are a solution, but on the downside, they lead to the formation byproducts hazardous to human health. In this study, aiming to develop bactericidal filters for the disinfection of drinking water; silver nanoparticles were deposited on alumina foams through three routes: sputtering DC, dip coating and in situ chemical reduction of silver nitrate. The depositions were characterized through X-ray diffraction, scanning electron microscopy and EDS element mapping. The influence of the depositions on permeability and mechanical properties of the ceramic foams was assessed and, in sequence, a preliminary antibacterial efficiency analysis was carried out. Characterization results indicate that the chemical reduction routes were efficient in depositing homogeneously distributed silver particles and that the concentration of the metallic precursor salt affects size and morphology of the particles. The antibacterial efficiency analysis indicates that the chemical reduction filters have potential for water disinfection

Efeito da adição de fibras da palma do licuri (syagrus coronata) no comportamento físico e mecânico de compósitos de matriz cimentícia

This research was motivated by the requirement of asbestos s replacement in building systems and the need to generate jobs and income in the country side of the state of Bahia, Brazil. The project aimed at using fibers from licuri leaves (syagrus coronata), an abundant palm in the region, to produce composites appropriate for the sustainable production of cement fibre reinforced products in small plants. The composites were produced in laboratory using Portland cement CP-II-F32, sand, water, licuri palm fiber contents of 1.0, 1.5 and 2.0% by weight of binder (two different fiber length) and metakaolin. The latter was chosen as an additional binder for its efficiency to reduce the alkalinity of cementitious matrixes therefore preventing the degradation of vegetable fibers. The characterization of the composite components was carried out by sieving and laser particle size analyses, thermal analysis, fluorescence and X-ray diffraction. The composites performance was evaluated by 3- point-bending tests, compressive strength, ultrasound module of elasticity, free and restrained shrinkage, water capillarity absorption and apparent specific gravity. It has been found that the addition of fibers increased the time to onset of cracking over 200.00% and a 25% reduction in cracks opening in the restrained shrinkage test. The capillary absorption reduced about 25% when compared to fiber-free composites. It was also observed with regard to flexural strength, compressive strength and specific gravity, that the addiction of fibers did not affect the composite performance presenting similar results for compounds with and without fibers. In general it can be stated that the reinforced composite fibers of palm licuri presents physical and mechanical characteristics which enable them to be used in the intended proposals of this research

Variedades e estilos na obra atribuída a Frei Carlos: novas perspetivas

Este trabalho de investigação centra-se no contributo dos exames de superfície e nas análises micro-analíticas no estudo de vinte e uma pinturas atribuídas à oficina de Frei Carlos, um dos grandes Mestres Luso-Flamengos ativos em território Nacional durante a primeira metade do século XVI. A "Pintura Luso-Flamenga" é uma expressão comummente usada na história da pintura Portuguesa do primeiro terço do século XVI e no seu sentido mais básico designa o trabalho de mestres flamengos que se instalaram em Portugal durante o reinado de D. Manuel I (1495- 1521) contribuindo decisivamente para o processo de renovação da pintura Portuguesa na época. O estudo integrado combina a pesquisa histórica em fontes documentais com exames de superfície e de caracterização material das obras de arte. O estudo material das pinturas foi realizado através de microscopia ótica, microscopia de infravermelhos com transformada de Fourier, espectroscopia de micro-Raman, microscopia eletrónica de varrimento acoplada com espectrometria de energia dispersiva de raios X, micro- difração de raios-X, cromatografia líquida de alta eficiência e pirólise acoplada à cromatografia gasosa /espectrometria de massa. Esta investigação envolveu técnicas complementares de análise de superfície e de ponto no estudo técnico e material das preparações, imprimitura, desenho subjacente, camadas pictóricas e sucessões estratigráficas, dando a conhecer os materiais utilizados na execução técnica das pinturas e evidenciando especificidades técnicas da produção artística. Este estudo pretende inclusivamente evidenciar alguns detalhes técnicos do artista que possivelmente estão relacionados com a herança das práticas Flamengas. O conhecimento de algumas particularidades da técnica deste Mestre também permitiu estabelecer comparações com duas pinturas que haviam sido atribuídas, com algumas reservas, a esta oficina de pintura Luso-Flamenga. Mais recentemente, como resultado de um estudo colaborativo, foi realizada uma ampla campanha de reflectografia infravermelhos, introduzindo novos dados acerca da execução técnica do desenho subjacente, o que contribuiu para diferenciar, nestas duas pinturas, outra "mão", atribuída então a um seguidor de Frei Carlos. Esta investigação introduz um novo e profundo conhecimento sobre a Oficina de Frei Carlos, permitindo estabelecer comparações com a obra do seu seguidor e com uma pintura também atribuída a esta oficina e que incorpora o Museu da National Gallery (NG5594), evidenciando os materiais utilizados na técnica de produção artística e especificidades técnicas aliadas aos processos criativos/ construtivos que permitem estabelecer os pontos de contacto e de diferenciação entre estas obras; Varieties and styles in the works attributed to Frei Carlos - new perspectives Abstract: This investigation is focused on the contributions of surface exams and micro-analytical research in the study of twenty one paintings attributed to Frei Carlos workshop, one of the most important Portuguese-Flemish painters active in our country during the first half of sixteen Century. "Portuguese-Flemish Painting" is a common expression used in the history of Portuguese painting of the first third of the sixteenth century and in its most basic meaning designates the work of Flemish masters who settled in Portugal during the reign of King Manuel I (1495-1521) contributing decisively to the process of renewal of Portuguese painting at the time. The integrated approach combines historical research on documental sources with surface examination and material characterization of the paintings by using state-of-art analytical techniques. Microanalysis was carried out by optical microscopy, micro-Fourier-transform infrared-spectroscopy, micro-Raman spectroscopy, scanning electron microscopy coupled with energy dispersive X-ray spectrometry, micro-X-ray diffraction analysis, high performance liquid chromatography and Pyrolysis gas chromatography mass spectrometry. This complementary surface and analytical research was involved in the technical and material characterization of grounds, underdrawings, primings, paint layers and its multi-layered build-up, providing access to the painter´s materials used in the technical execution of the paintings and details of the technique of artistic production. This study also intends to expose some usual details of the artist’s technique which are possibly related to the Master´s Flemish influence. The knowledge of some particularities of the Master´s technique also allowed a new comparison with two paintings that had been attributed with some reserves to this Portuguese-Flemish workshop. More recently, as a result of a collaborative study, an extensive infrared reflectography campaign was made, giving new data concerning underdrawings technical execution and contributing to differentiate, in these two paintings, another “hand”, attributed to a follower of Frei Carlos. Complementary analytical research also added a new and deep insight into Frei Carlos workshop, his follower and a panel that still attributed to Frei Carlos workshop that integrates the National Gallery´s Museum (NG5594), evidencing the materials used in technical production, their models and sources of artistic inspiration, techniques and pictorial construction procedures that could specifically relate or distinguish between them.

Analytical evaluation of paper degradation

The aim of this work was in first place to define a methodology for the use of Py-GC/MS as a characterization technique for the organic compounds present in paper samples containing foxing stains, paper have a complex structure and mostly consist with cellulose fibers. Additionally, it was intent to characterize paper samples containing foxing stains with a batch of non-destructive analytical techniques. The work intent to deepen our knowledge on foxing stains, its chemical nature and morphological aspects. For characterization of the morphology of paper samples and foxing stains was used photography under different illuminations and optical microscopy. The presence of fibers disruption was observed with scanning electron microscopy coupled with energy dispersive spectroscopy (SEM-EDS), and also the nature of the fillers that is present in different areas. Attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) was used for identification of the sizing agents, determination of the chemical composition of additives that were used for production of paper, and comparison between foxing stains and unfoxed areas was allowed. Micro X-ray diffraction was used to evaluate the crystalline fillers in the sample. Pyrolysis-Gas Chromatography/Mass Spectrometry (Py-GC/MS was used for chemical analysis to identify the organic components and different classes of organic compounds; Resumo: O objetivo deste trabalho foi definir, em primeiro lugar, uma metodologia para o uso de Py-GC / MS como técnica de caracterização dos compostos orgânicos presentes em amostras de papel contendo manchas de foxing, o papel tem uma estrutura complexa e consiste principalmente com fibras de celulose. Além disso, pretendia caracterizar amostras de papel contendo manchas de raposas com técnicas analíticas não destrutivas. Para a caracterização da morfologia das amostras de papel e das manchas de foxing foi usada fotografia sob diferentes iluminações e microscopia óptica. A presença de fibras de ruptura foi observada por microscopia electrónica de varrimento juntamente com espectroscopia dispersiva de energia (EDS-SEM), assim como a natureza dos materiais de enchimento que está presente em diferentes áreas. Espectroscopia de infravermelho com transformada de Fourier em modo de reflexão total atenuada (ATR-FTIR) foi utilizada na identificação dos agentes de colagem, e na determinação da composição química de aditivos usados na produção de papel, e a comparação entre foxing manchas e áreas unfoxed foi deixada. Micro difracção de raios X foi usada para avaliar o enchimentos cristalinos na amostra. Cromatografia pirólise-gasosa / espectrometria de massa (Py-GC / MS) foi utilizada para análise química para identificar os componentes orgânicos e diferentes classes de compostos orgânicos.

Análise comparativa entre amostras de raízes com e sem sintomas de amarelecimento fatal de Elaeis guineensis JACQ. (dendezeiro).

O dendê possui grande importância econômica para o estado do Pará, no entanto, o Amarelecimento Fatal (AF) tem sido um grande obstáculo para a sua produção. Alguns elementos químicos foram testados, em pesquisas anteriores, para saber sua relação com o AF e as consequências da sua deficiência. A análise química por espectrometria de raios-x por dispersão de energia (EDS) é um recurso da microscopia de varredura (MEV) que permite fazer uma avaliação química da amostra. O presente trabalho teve como objetivo analisar semiquantitativamente os elementos químicos cálcio e silício, em quatro diferentes tecidos de raízes terciárias e quaternárias de Elaeis guineensis Jacq. (Dendezeiro) com grau zero (sem sintoma) e grau dez (com sintoma) de amarelecimento fatal (AF). Em plantas com sintomas de AF as médias percentuais para cálcio são de 0,731 a 4,453 e para silício 2,619 a 8,124 dentre os tecidos analisados, enquanto que em plantas sem sintomas as médias são de 0,712 a 5,313 e 2,963 a 7,494, para cálcio e silício, respectivamente. A diferença encontrada em relação as porcentagens dos elementos nos diferentes tecidos radiculares analisados, é maior do que entre os diferentes graus da doença, exceto para o aerênquima. Em relação ao acumulo de cálcio e silício nos tecidos, o comportamento das plantas com sintoma e sem sintoma é muito parecido. A presença de cálcio aumenta conforme se aproxima do cilindro vascular, ocorrendo o comportamento variado com o silício.

Are skeletally mature female rats a suitable model to study osteoporosis?

OBJECTIVE: To analyze if female Wistar rats at 56 weeks of age are a suitable model to study osteoporosis. MATERIALS AND METHODS: Female rats with 6 and 36 weeks of age (n = 8 per group) were kept over a 20-week period and fed a diet for mature rodents complete in terms of Ca, phosphorous, and vitamin D. Excised femurs were measured for bone mass using dual-energy x-ray absorptiometry, morphometry, and biomechanical properties. The following serum mar-kers of bone metabolism were analyzed: parathyroid hormone (PTH), osteocalcin (OC), osteoprotegerin (OPG), receptor activator of nuclear factor Κappa B ligand (RANKL), C-terminal peptides of type I collagen (CTX-I), total calcium, and alkaline phosphatase (ALP) activity. RESULTS: Rats at 56 weeks of age showed important bone metabolism differences when compared with the younger group, such as, highest diaphysis energy to failure, lowest levels of OC, CTX-I, and ALP, and elevated PTH, even with adequate dietary Ca. CONCLUSION: Rats at 26-week-old rats may be too young to study age-related bone loss, whereas the 56-week-old rats may be good models to represent the early stages of age-related changes in bone metabolism.

A medição da grandeza practical peak voltage na prática radiológica

OBJETIVO: O objetivo deste trabalho foi estudar a grandeza practical peak voltage (PPV), determinada a partir da forma de onda de tensão aplicada a tubos radiológicos, e compará-la com algumas definições de kVp para diferentes tipos de geradores: monofásico (onda completa, clínico), trifásico (seis pulsos, clínico) e potencial constante (industrial). MATERIAIS E MÉTODOS: O trabalho envolveu a comparação do PPV medido invasivamente (utilizando um divisor de tensão) com a resposta de dois medidores comerciais não invasivos, além dos valores de outras grandezas usadas para medição da tensão de pico aplicada ao tubo de raios X, e a análise da variação do PPV com a ondulação percentual da tensão (ripple). RESULTADOS: Verificou-se que a diferença entre o PPV e as definições mais comuns de tensão de pico aumenta com o ripple. Os valores de PPV variaram em até 3% e 5%, respectivamente, na comparação entre medições invasivas e não invasivas feitas com os equipamentos trifásico e monofásico. CONCLUSÃO: Os resultados demonstraram que a principal grandeza de influência que afeta o PPV é o ripple da tensão. Adicionalmente, valores de PPV obtidos com medidores não invasivos devem ser avaliados considerando que eles dependem da taxa de aquisição e da forma de onda adquirida pelo instrumento.